Oxygen Reduction Reaction Catalysts Research Articles

Main Group SnN4O Single Sites with Optimized Charge Distribution for Boosting the Oxygen Reduction Reaction.

Transition metal single-atom catalysts (SACs) have been regarded as possible alternatives to platinum-based materials due to their satisfactory performance of the oxygen reduction reaction (ORR). By contrast, main-group metal elements are rarely studied due to their unfavorable surface and electronic states. Herein, a main-group Sn-based SAC with penta-coordinated and asymmetric first-shell ligands is reported as an efficient and robust ORR catalyst. The introduction of the vertical oxygen atom breaks the symmetric charge balance, modulating the binding strength to oxygen intermediates and decreasing the energy barrier for the ORR process. As expected, the prepared Sn SAC exhibits outstanding ORR activity with a high half-wave potential of 0.912 V (vs RHE) and an excellent mass activity of 13.1 A mgSn-1 at 0.850 V (vs RHE), which surpasses that of commercial Pt/C and most reported transition-metal-based SACs. Additionally, the reported Sn SAC shows excellent ORR stability due to the strong interaction between Sn sites and the carbon support with oxygen atom as the bridge. The excellent ORR performance of Sn SAC was also proven by both liquid- and solid-state zinc-air battery (ZAB) measurements, indicating its great potential in practical applications.

N‐Doped Carbon Nanofibers and Carbon Nanotubes‐Encapsulated CoNi Alloy as Highly Active Oxygen Reduction Catalysts for Direct Methanol Fuel Cells

The slow oxygen reduction kinetics of direct methanol fuel cell (DMFCs) are one of the limiting factors affecting its application. Therefore, exploring nonprecious catalysts with high activity and methanol resistance is urgently needed. Herein, zeolitic imidazolate framework‐8 particles are first blended with different proportions of metal salts (Ni as well as Co) and further electrospun to obtain a nanofiber precursor. After pyrolysis treatment, a composite catalyst (CoNi@N‐CNFs) with a highly dispersed CoNi alloy phase supported by porous N‐doped carbon nanofiber and carbon nanotube is prepared. The surface electronic structure can be reasonably adjusted by optimizing the doping ratio of Ni and Co. The CoNi@N‐CNFs shows high oxygen reduction activity and methanol resistance. Half‐wave potential and the onset potential of Co1Ni1@N‐CNFs (Co: Ni mole ratio = 1:1) are 0.79 and 0.87 V. Additionally, Co1Ni1@N‐CNF‐modified DMFC endows a high power density (24.07 mW cm−2), which is close to Pt/C‐based DMFC (27.59 mW cm−2). Rich active sites, large specific surface area, and synergy between CoNi alloy and N configuration of CoNi@N‐CNFs effectively accelerate electron transfer, resulting in the superior catalytic activity. This work provides a new strategy to design effective 1D oxygen reduction reaction catalysts in fuel cells.

Instantaneous Thermal Energy for Swift Synthesis of Single-Atom Catalysts for Unparalleled Performance in Metal-Air Batteries and Fuel Cells.

Based on experimental and computational evidence, phthalocyanine (Pc) compounds in the form of quaternary bound metal-nitrogen (N) atoms are the most effective catalysts for oxygen reduction reaction (ORR). However, the heat treatment process used in their synthesis may compromise the ideal structure, causing the agglomeration of transition metals. To overcome this issue, we developed a novel method for synthesizing iron (Fe) single-atom catalysts with ideal structures supported by thermally exfoliated graphene oxide (GO). This was achieved through a short heat-treatment of only 2.5min involving FePc and N,N-dimethylformamide in the presence of GO. According to the synthesis mechanism revealed by this study, carbon monoxide acts as a strong linker between the single Fe atoms and graphene. It facilitates the formation of a structure containing oxygen species between FeN4 and graphene, which provides high activity and stability for the ORR. These catalysts possess an enormous number of active sites and exhibit enhanced activity towards the alkaline ORR. They have demonstrated excellent performance when applied to real electrochemical devices, such as zinc-air batteries and anion exchange membrane fuel cells. We expect that the instantaneous heat treatment method developed in our study will aid in the development of high-performing single-atom catalysts. This article is protected by copyright. All rights reserved.

Atomically Dispersed p-Block Aluminum-Based Catalysts for Oxygen Reduction Reaction.

The main group metals are commonly perceived as catalytically inert in the context of oxygen reduction reactions (ORR) due to the delocalized valence orbitals. Regulating the local environment and structure of metal center coordinated by nitrogen ligands (M-Nx) is a promising approach to accelerate catalytic dynamics. Herein, we, for the first time, report the atomically dispersed Al catalysts coordinated with N and C atoms for 4-electron ORR. The axial coordinated pyrrolyl N group (No) is constructed in the Al-N4-No moiety to regulate the p-band structure of Al center, effectively steering the local environment and structure of the square planar Al-N4 sites, which typically exhibit too strong interaction with ORR intermediates. The dynamic covalency competition of axial Al-No and Al-O bonding could endow the Al center with moderate hybridization between Al 3p orbital and O 2p orbital, alleviating the binding energy of ORR intermediates. The as-prepared Al-N4-No electrocatalyst exhibits excellent ORR activity, selectivity, and durability, along with the rapid kinetics as demonstrated by in situ Raman spectroscopy. This work offers a fundamental comprehension of the fine regulation on p-band and guides the rational design of main-group metal-based single atom catalysts.

Optimized porous nanostructure of carbon fibers enabling excellent stability of Pt-based catalysts for oxygen reduction reaction

Facile synthesis of highly-dispersed Pt-based electrocatalysts on porous carbon supports with strong durability is extremely desirable for oxygen reduction reaction but remains challenging. The influence of pores in carbon supports on the stability and activity of catalysts is ambiguous and needs to be elucidated. Targeting this aim, herein, we prepared a series of carbon nanofibers with tunable pore diameter and specific surface area using the resorcinol-formaldehyde (RF) resins as a model system. Homogeneous composite precursors composed of RF resins and silica colloids were synthesized by the surfactant-assisted simultaneous polycondensation of RF resins and tetraethylorthosilicate (TEOS). The diameter of the pores induced by removal of silica could be controllable tailored through thermal treatment of the composite under various target temperatures. Pt3Co alloy nanoparticles loaded on the as-synthesized porous carbon nanofibers were prepared by an optimized wet-impregnation method. The experimental results indicated that the carbon nanofibers with pore size distribution focused on ∼1.27 nm and ∼2.34 nm provided the best stability without limiting current density decay, and negative shift of half-wave potential (E1/2) and mass activity (MA) loss of Pt after 20000 potential cycles are relatively mild. Conversely, negative shift of 21 mV, 15 mV and 22 mV in E1/2 and mass activity loss of 51.8%, 30.2% and 33.0% were observed for the Pt3Co nanoparticles supported on MC-60, MC-100 and MC-140 matrices which have pore size distribution focused on ∼2.73 nm, ∼2.73 nm as well as ∼4.66 nm, and ∼4.66 nm, respectively. This work demonstrates the importance of micropores and small mesopores for activity and long-term stability enhancement of carbon supported Pt-based electrocatalysts.

Carbon‐Embedded Pt Alloy Cluster Catalysts for Proton Exchange Membrane Fuel Cells

AbstractMinimizing the use of platinum (Pt) in proton exchange membrane fuel cells (PEMFCs) is crucial for expanding the PEMFC market. The most straightforward approach would be to reduce the size of Pt particles. However, small Pt clusters, particularly those <2 nm in size, typically exhibit reduced activity for the oxygen reduction reaction (ORR) due to the overly strong adsorption of oxygen intermediates. Additionally, these small Pt clusters tend to degrade more quickly, resulting in lower durability. In this study, carbon‐embedded Pt alloy cluster catalysts (PtFe, PtCo, PtNi) that demonstrate high activity and durability in the PEMFC cathode are presented. Density functional theory calculations indicate that carbon atoms stably adsorb onto the Fe sites of PtFe clusters, making the neighboring Pt sites active for ORR with an optimal adsorption strength for oxygen intermediates. This research can pave the way for developing durable and efficient ORR catalysts while significantly reducing Pt usage in PEMFCs.

Single-atom Fe catalysts with pyrrolic-type FeN4 sites for efficient oxygen reduction reaction: Identifying the roles of different N species

Developing electrocatalysts with efficient cathode oxygen reduction reaction (ORR), for example, iron-based single-atom catalysts (Fe-SACs), has been deemed necessary to accelerate the commercialisation process of zinc (Zn)–air batteries. Nevertheless, determining how various nitrogen species and active metal centres coordinate on an atomic scale remains unclear and inadequately explained. Herein, we demonstrate a soft-template-aided technique using Fe-containing molecules (e.g. iron phthalocyanine [FePc], Fe-1,10-phenanthroline [Fe-Phen] and Fe-glucose) to enhance the performance of Fe-SACs in terms of ORR. In this technique, FePc molecules can be converted into atomically dispersed pyrrolic-type iron–nitrogen (FeN4) sites during a pyrolytic process. The resultant catalyst exhibits excellent ORR activity (half-wave potential = 0.90 V) in alkaline medium and standing battery performance when used in Zn–air batteries (peak power density = 197.3 mW cm−2 and specific capacity = 796.2 mAh g−1). As per the findings from control experiments and characterisation studies, electron transfer between the support and the active Fe centre amplifies the ORR performance. Theoretical calculations substantiate that Fe sites coordinated with pyrrolic N atoms govern the electronic configuration of the catalysis, reducing the free energy absorption of reaction intermediates and thus increasing its intrinsic ORR capability. Herein, we aim to offer a fresh perspective on the relation between coordination environments and catalytic activity in ORR catalysts.

Carbon Corrosion Induced by Surface Defects Accelerates Degradation of Platinum/Graphene Catalysts in Oxygen Reduction Reaction.

Graphene supported electrocatalysts have demonstrated remarkable catalytic performance for oxygen reduction reaction (ORR). However, their durability and cycling performance are greatly limited by Oswald ripening of platinum (Pt) and graphene support corrosion. Moreover, comprehensive studies on the mechanisms of catalysts degradation under 0.6-1.6V versus RHE (Reversible Hydrogen Electrode) is still lacking. Herein, degradation mechanisms triggered by different defects on graphene supports are investigated by two cycling protocols. In the start-up/shutdown cycling (1.0-1.6V vs.RHE), carbon oxidation reaction (COR) leads to shedding or swarm-like aggregation of Pt nanoparticles (NPs). Theoretical simulation results show that the expansion of vacancy defects promotes reaction kinetics of the decisive step in COR, reducing its reaction overpotential. While under the load cycling (0.6-1.0V vs.RHE), oxygen containing defects lead to an elevated content of Pt in its oxidation state which intensifies Oswald ripening of Pt. The presence of vacancy defects can enhance the transfer of electrons from graphene to the Pt surface, reducing the d-band center of Pt and making it more difficult for the oxidation state of platinum to form in the cycling. This work will provide comprehensive understanding on Pt/Graphene catalysts degradation mechanisms.

Single atom catalysts with anion center toward oxygen electrocatalysis based on the conductive 1T-HfTe2

Advancing efficient catalysts for oxygen reduction reaction (ORR) or oxygen evolution reaction (OER) is imperative for commercializing emerging energy devices. Using density functional theory (DFT) calculations, we propose doping different transition metal (TM) atoms to regulate the electronic structures of the two-dimensional 1T-HfTe2 monolayer to achieve bifunctional catalysis for the ORR/OER. Due to the small electronegativity of the Hf atom, we found the doped TMs can generally form anion centers by accepting abundant charges from the Hf interlayer. At the same time, the highly conductive 1T-HfTe2 contributes to the charge transfer between the active center and the reaction intermediates, rendering the designed SACs the tunable activity for the reactions. By comparing the theoretical overpotentials of ORR and OER on 15 single-atom catalysts (SACs), Pt-doped system exhibits excellent catalytic activity for both ORR and OER, outperforming the traditional Pt(111) and RuO2(110) catalysts. Based on the charge transfer mechanism, we clarified that the doped TM atoms act as a ‘bridge’ to transfer the electrons from the substrate to the reaction intermediates, thereby effectively contributing to the improvement of catalytic activity. In summary, our study shows that, by doping appropriate TM atoms, the intrinsic inert HfTe2 can be activated toward efficient ORR/OER. This could provide some guidance for the design of new two-dimensional ORR/OER bifunctional catalyst materials.

NC Loaded PtM Alloy from M-NC with Ultralow Pt Loading for Oxygen Reduction Reaction

Developing low Pt or non-precious metal catalysts for oxygen reduction reaction (ORR) has becoming necessary in recent years. Herein, PtM alloy anchored on nitrogen-doped carbon (PtM/NC, M=Fe, Co) catalyst with ultralow Pt loading (∼1 wt%) is prepared from the simple two-process pyrolysis, namely from C to M-NC then to PtM/NC. The as-prepared PtM/NC (M=Fe, Co) shows an excellent ORR catalytic performance with the peak potential and half-wave potential of 0.901 and 0.870 V for PtFe/NC, 0.868 and 0.845 V for Pt3Co/NC. The ORR on PtM/NC (M=Fe, Co) is a mainly direct 4-electron reaction pathway (3.75–3.90) in alkaline solution. Moreover, they possess good methanol tolerance and stability. Synergistic effect of Pt and M together with N species result in the excellent ORR catalytic activity of PtM/NC (M=Fe, Co). The negative shift of Pt binding energy caused by both lattice contraction and electron orbital coupling from M is beneficial for reducing the d-band center of Pt, weakening the oxygen binding energy and enhancing the ORR intrinsic activity of Pt. The strong interactions between NC and PtM alloy are beneficial for anchoring PtM nanoparticles, promoting the stability of catalyst. This work provides a new strategy for preparing ultralow Pt loading catalysts.

Enhanced corrosion protection of rebars in alkaline solutions by ferroporphyrin and the mechanisms of electron consumption and lattice reconstruction

Abstract Reinforced concretes are the primary materials in coastal and offshore engineering. In alkaline environment of concrete, the anodic process is passivation of rebars and the conjugated cathodic process is oxygen reduction reaction (ORR). It is proposed that a novel approach to enhance the passivation films through catalyzed ORR by iron meso-tetra(4-carboxyphenyl)porphine (FeTCPP). The ORR catalyst FeTCPP promotes the formation of passivation film, as it accelerates the consumption of abundant electrons generated and accumulated by the anodic formation of passivation films. The passivation films of rebars are highly defective Fe3O4 semiconductor. The dissolution of interstitial ferrous ions and lattice iron ions produces defects of O ion vacancies, Fe ion vacancies and interstitial Fe ions, and they further cause the formation and accumulation of Fe atom vacancies on the metal surface, leading to the collapse of the passivation films. The FeTCPP adsorbs on the surface of passivation films, hindering the dissolution of lattice iron ions and interstitial ferrous ions, thereby inhibiting the generation and accumulation of Fe atom vacancies and improving the integrity and protective ability of the passivation films.

Synthesis of biomass nitrogen-doped catalysts and their electrocatalytic performance in fuel cells

At present, biomass materials have the characteristics of low cost, stability, and relatively high activity, which is expected to replace platinum-based (Pt) materials as cathode catalysts. In this paper, Zn, Fe-N-C catalyst materials and Fe-N-C catalyst were composited by high-temperature calcination. Their crystal and morphological structures were featured by X-ray diffraction instruments (XRD) and scanning electron microscopy (SEM). Their activity and stability to oxygen reduction were tested by an electrochemical workstation, and it was found that Zn, Fe-N-C catalyst materials had the best performance. The investigation of this paper can furnish an effective method for oxygen reduction reaction catalysts.

Theoretical insights on 3D transition metal anchored poly[5,10,15,20-tetra(4-ethynylphenyl)porphyrin]diyne as highly efficient bifunctional catalyst toward ORR and OER

Searching for highly active oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts is a challenging task in the development of clean energy devices. Herein, by using the poly[5,10,15,20-tetra(4-ethynyl-phenyl)porphyrin]diyne (TEPPD), we designed ORR and OER catalysts by anchoring 3d transition metal into TEPPD (TM@TEPPD, TM = Mn-Zn). Our study indicated that Fe@TEPPD is the best bifunctional catalyst for both ORR and OER. By proposing a proper descriptor, Ni-N3@TEPPD (Ni is only coordinated with three N atoms) is designed and also predicted to be a promising bifunctional catalyst. For Fe@TEPPD, ORR and OER become inactive when the acetylene bond in TEPPD is broken. The surface Pourbaix diagram indicated that on the surface of Fe@TEPPD, ORR and OER can be carried out at the whole pH region due to the high dissolution potential of Fe2+. For Ni-N3@TEPPD, however, the dissolution potential 0.71 V for Ni2+is low. Thus, for Ni-N3@TEPPD, ORR can be carried out only after pH>2.54, while OER is not likely at the whole pH region. This suggested that the conclusions from the free energy changes at URHE=0 and pH=0 could be different when different potentials and pH values are considered.

Bimetallic Center Metal–Organic Framework Catalysts for the Two-Electron Oxygen Reduction Reaction

Bimetallic Center Metal–Organic Framework Catalysts for the Two-Electron Oxygen Reduction Reaction

Interlayer Polymerization to Construct a Fully Conjugated Covalent Organic Framework as a Metal-Free Oxygen Reduction Reaction Catalyst for Anion Exchange Membrane Fuel Cells.

Two-dimensional (2D) covalent organic frameworks (COFs) have a multilayer skeleton with a periodic π-conjugated molecular array, which can facilitate charge carrier transport within a COF layer. However, the lack of an effective charge carrier transmission pathway between 2D COF layers greatly limits their applications in electrocatalysis. Herein, by employing a side-chain polymerization strategy to form polythiophene along the nanochannels, a conjugated bridge is constructed between the COF layers. The as-synthesized fully conjugated COF (PTh-COF) exhibits high oxygen reduction reaction (ORR) activity with narrowed energy band gaps. Correspondingly, PTh-COF is tested as a metal-free cathode catalyst for anion exchange membrane fuel cells (AEMFCs) which showed a maximum power density of 176mWcm-2 under a current density of 533mAcm-2. The density functional theory (DFT) calculation reveals that interlayer conjugated polythiophene optimizes the electron cloud distribution, which therefore enhances the ORR performance. This work not only provides new insight into the construction of a fully conjugated covalent organic framework but also promotes the development of new metal-free ORR catalysts.

A Non‐Macrocycle Thiolate‐Based Cobalt Catalyst for Selective O2 Reduction into H2O

AbstractThe reduction of dioxygen to produce selectively H2O2 or H2O is crucial in various fields. While platinum‐based materials excel in 4H+/4e− oxygen reduction reaction (ORR) catalysis, cost and resource limitations drive the search for cost‐effective and abundant transition metal catalysts. It is thus of great importance to understand how the selectivity and efficiency of 3d‐metal ORR catalysts can be tuned. In this context, we report on a Co complex supported by a bisthiolate N2S2‐donor ligand acting as a homogeneous ORR catalyst in acetonitrile solutions both in the presence of a one‐electron reducing agent (selectivity for H2O of 93 % and TOFi=3 000 h−1) and under electrochemically‐assisted conditions (0.81 V <η<1.10 V, selectivity for H2O between 85 % and 95 %). Interestingly, such a predominant 4H+/4e− pathway for Co‐based ORR catalysts is rare, highlighting the key role of the thiolate donor ligand. Besides, the selectivity of this Co catalyst under chemical ORR conditions is inverse with respect to the Mn and Fe catalysts supported by the same ligand, which evidences the impact of the nature of the metal ion on the ORR selectivity.

Innovative Strategy for Developing PEDOT Composite Scaffold for Reversible Oxygen Reduction Reaction.

Metal-air batteries are an emerging technology with great potential to satisfy the demand for energy in high-consumption applications. However, this technology is still in an early stage, facing significant challenges such as a low cycle life that currently limits its practical use. Poly(3,4-ethylenedioxythiophene) (PEDOT) conducting polymer has already demonstrated its efficiency as catalyst for oxygen reduction reaction (ORR) discharge as an alternative to traditional expensive and nonsustainable metal catalysts. Apart from that, in most electrochemical processes, three phenomena are needed: redox activity and electronic and ionic conduction. Material morphology is important to maximize the contact area and optimize the 3 mechanisms to obtain high-performance devices. In this work, porous scaffolds of PEDOT-organic ionic plastic crystal (OIPC) are prepared through vapor phase polymerization to be used as porous self-standing cathodes. The scaffolds, based on abundant elements, showed good thermal stability (200 °C), with potential ORR reversible electrocatalytic activity: 60% of Coulombic efficiency in aqueous medium after 200 cycles.

Metal–organic framework–derived trimetallic particles encapsulated by ultrathin nitrogen-doped carbon nanosheets on a network of nitrogen-doped carbon nanotubes as bifunctional catalysts for rechargeable zinc–air batteries

Economical oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) bifunctional catalysts with high activity aimed at replacing precious metal catalysts for rechargeable zinc-air batteries (ZABs) must be developed. In this study, a multiple hierarchical-structural material is developed using a facile dielectric barrier discharge (DBD) plasma surface treatment, solvothermal reaction, and high-temperature carbonization strategy. This strategy allows for the construction of nanosheets using nitrogen-doped carbon (NC) material-encapsulated ternary CoNiFe alloy nanoparticles (NPs) on a network of NC nanotubes (NCNTs), denoted as CoNiFe–NC@p–NCNTs. Precisely, the presence of abundant CoNiFe alloy NPs and the formation of M–N–C active sites created by transition metals (cobalt, nickel, and iron) coupled with NC can provide superior OER/ORR bifunctional properties. Moreover, the prepared NC layers with a multilevel pore structure contribute to a larger specific surface area, exposing numerous active sites and enhancing the uniformity of electron and mass movement. The CoNiFe0.08–NC@p–NCNTs show remarkable dual functionality for electrochemical oxygen reactions (ORR half-wave potential of 0.811 V, limiting current density of 5.73 mA cm−2 measured with a rotating disk electrode at a rotation speed of 1600 rpm, and OER overpotential of 351 mV at 10 mA cm−2), which demonstrates similar ORR performance to 20 wt% Pt/C and better OER performance than the commercial RuO2. A liquid ZAB prepared using the proposed material has excellent bifunctionality with an open-circuit voltage of 1.450 V and long-term cycling stability of 230 h@10 mA cm−2.

Electrode microstructure design to improve effective utilization of Fe-N/C catalysts towards oxygen reduction reaction process

Fe-N/C materials have shown intrinsic activities comparable to Pt/C catalysts for oxygen reduction reaction on rotating ring-disk electrodes (RRDE). However, due to the insufficient three-phase interfaces (TPIs) and high oxygen transport resistance (RT), the high intrinsic activity cannot be sufficiently utilized in electrodes, resulting in a gap between the intrinsic catalytic activity on RRDE and the performance in devices. To expand the TPIs and promote oxygen transport, a novel electrode with a transition layer structure is proposed to disperse the active sites. The dispersion degree of active sites is optimized by tuning the solid–liquid interfacial energy between the ink solvent and the substrate. A high electrochemical active area of 1264 cm2 and a low RT of 2.0 s cm−1 are achieved for the electrode prepared by an alcohol-rich ink. The simulation and experimental results demonstrate that the microstructure can benefit the extension of TPIs and facilitate oxygen transport in the air cathode, ultimately achieving efficient utilization of catalytic activities. A maximum power density of 35.4 mW cm−2 is achieved in a membrane-less direct formate fuel cell, surpassing most congeneric devices. Our approach clarifies the relationship between TPI construction, mass transport, and electrode microstructure, which successfully exploits the intrinsic activity on air cathodes and improves the power generation ability.

Superior Catalytic Performance and Methanol Tolerance of Co@Mesoporous Graphene Nanocomposites toward Oxygen Reduction Reaction

AbstractThe global energy crisis and growing concerns about environmental pollution have spurred researchers to explore eco‐friendly methods of generating clean energy. Previous studies have often relied on noble metal catalysts to facilitate oxygen reduction reactions (ORR) in energy production reactions. However, their high cost has limited their widespread adoption, making the development of highly active and affordable ORR catalysts a significant challenge. In this study, a vacuum heat treatment technique was employed to fabricate a cobalt‐loaded mesoporous graphene (Co−Gs) nanocomposite. The inclusion of cobalt in graphene enhances the reaction, while the presence of mesoporous graphene provides a larger surface area to accommodate the active sites of Co. This synergistic effect promotes the improvement of catalytic performance. Additionally, the stability and methanol tolerance of Co−Gs nanocomposites is also superior than that of Pt−C. The excellent catalytic performance of the Co−Gs nanocomposite is attributed to a four‐electron pathway within the nanocomposite, as demonstrated by electrocatalytic kinetics investigations. Additionally, the interface interaction between the Co nanoparticles and Gs enhances the efficiency of electron transfer, effectively improving the catalytic performance. These findings highlight the potential of Co‐loaded graphene nanocomposites as highly efficient and cost‐effective electrocatalysts for clean energy application.