Output Load Regulation Research Articles

A Constant-on-Time Control DC–DC Buck Converter With the Pseudowave Tracking Technique for Regulation Accuracy and Load Transient Enhancement

Constant-on-time (COT) control with an additional current feedback path in conventional buck converters can remove the need of large equivalent series resistance (ESR) at the output capacitor but it induces degraded output voltage regulation accuracy and slow transient response owing to opposite reaction between the output voltage and the additional current feedback information. Therefore, this paper proposes the pseudowave tracking (PWT) technique to reduce the load-dependent dc offset voltage of output load regulation while keeping the fast transient response similar to conventional COT buck converter with large ESR. The PWT technique further improves the transient response instantly by extending on-time and off-time periods during light-to-heavy and heavy-to-light load changes, respectively. The test chip fabricated in 28 nm CMOS process has demonstrated the improvement of offset voltage from 42 to 4 mV, while the transient response can be improved to 4 and 5 μs with load changes from 0.3 to 1.7 A and vice versa, respectively.

A programmable, multichannel power supply for SIPMs with temperature compensation loop and Ethernet interface

Among the different techniques available, the SiPM power supply described in this paper uses output voltage and sensor temperature feedback. A high-resolution ADC digitizes both the output voltage and an analog signal proportional to the SiPM temperature for each of its 16 independent outputs. The appropriate change in the bias voltage is computed in a micro-controller and this correction is applied via a high resolution DAC to the control input of a DC/DC module that produces the output voltage. This method allows a reduction in gain variations from typically 30% to only 0.5% in a 10 °C range. The power supply is housed in a 3U-height aluminum box. A 2.8'' touch screen on the front panel provides local access to the configuration and monitoring functions using a graphical interface. The unit has an Ethernet interface on its rear side to provide remote operation and integration in slow control systems using the encrypted and secure SSH protocol. A LabVIEW application with SSH interface has been designed to operate the power supply from a remote computer. The power supply has good characteristics, such as 85 V output range with 1 mV resolution and stability better than 2 mVP, excellent output load regulation and programmable rise and fall voltage ramps. Commercial power supplies from well-known manufacturers can show far better specifications though can also result in an over featured and over costly solution for typical applications.

The Test Investigation and Design Improvements of Voltage Regulator Performance

Voltage regulator is designed to automatically maintain the constant of regular voltage level. Every automotive IC has its own regulator module for analog and logic circuit power supply. The output load regulation and current consumption are directly related to the IC’s performance, or even the whole application module. The performance of regulator is not only related with the output parameters, but also the protection character. The over voltage protection feature guarantees the IC’s working environment within specific voltage input range. This article use one IDC’s (Intelligent Distribution Controller) regulator module to describe the design theory for regulator over voltage performance improvement. The test investigation and verification on ATE (Automatic Test Equipment) are demonstrated. The parameter of over voltage threshold is optimized obviously by 2% yield increasing.

A high-current very wide-band transconductance amplifier

A novel design approach for a high-current, very-wide-band transconductance amplifier is described. The approach is based on paralleling the input and output of complementary unipolar current-mirror cells. Each cell has a fixed current gain determined by the ratio of two resistors. A differential input voltage-to-current circuit drives the cell array. The design avoids the need for a single low-resistance current-sensing resistor and the attendant problems inherent in such resistors. Although the concept is still under development, a prototype of the cell-based transconductance amplifier was implemented with ten positive and ten negative current cells to gain some experimental familiarity with the approach in addition to providing verification of computer simulation results. The prototype transconductance amplifier is DC coupled, has a 3-dB bandwidth of about 750 kHz, and can deliver up to 35 A RMS (root mean square) at 100 kHz with an output compliance voltage of 5 V RMS. Other important characteristics such as output-load regulation and DC offsets are discussed.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>