Orthogonal Frequency Division Multiplexing Pulse Research Articles

Radar Sensor and Data Communication System Based on OFDM Without Cyclic Prefix

The high data rate and large bandwidth of orthogonal frequency division multiplexing(OFDM) modulations have made the integrated waveform design using OFDM-based signals a popular research topic in recent years. However, OFDM signals are sensitive to the Doppler frequency bias and multipath effects, which are traditionally accommodated by cyclic prefixes (CP) inserted before each OFDM symbol. Since the CP is the partial copy of the OFDM symbol, it not only loses energy in communication systems but also forms false targets after radar signal processing. To address the shortcomings of conventional OFDM, this paper proposes a modified CP-free OFDM joint radar communication system(JRCS). It transmits the OFDM pulse signal to certain targets and/or communication systems and receives echoes in the pulse repetition interval. By removing CP, the radar system can compress the echoes without ghost targets. Through reasonable sampling which should be designed significantly, the communication systems demodulate the OFDM pulse to extract information without intersymbol interference in multipath channels. Furthermore, the constraints of the time, frequency, and sampling on the system are analyzed in detail and an illustrating system under an air-to-ground scenario is constructed. Simulation results show that the proposed signal design and processing method has a better performance compared to conventional OFDM signals.

ECCM Schemes against Deception Jamming Using OFDM Radar with Low Global PAPR.

In this paper, a type of effective electronic counter-countermeasures (ECCM) technique for suppressing the high-power deception jamming using an orthogonal frequency division multiplexing (OFDM) radar is proposed. Concerning the velocity deception jamming, the initial phases of the pulses transmitted in a coherent processing interval (CPI) are designed to minimize the jamming power within a specific range, forming a notch around the jamming in the Doppler spectrum. For the purpose of suppressing the range deception jamming and the joint range-velocity deception jamming, the phase codes of the subcarriers belonging to the OFDM pulses are optimized to minimize the jamming power, distributing some specific bands in the range and the range-velocity domain, respectively. According to Parseval’s theorem, the phase encoding, acting as the coding manner of the OFDM subcarriers can ensure that the energy of each OFDM symbol stays the same. It is worth noticing that the phase codes of the OFDM subcarriers can influence the peak-to-average power ratio (PAPR). Thus, an optimization problem is formulated to optimize the phase codes of the subcarriers under the constraint of global PAPR, which can regulate the PAPRs of multiple OFDM symbols at the same time. The proposed problem is non-convex; therefore, it is a huge challenge to tackle. Then we present a method named by the phase-only alternating direction method multipliers (POADMM) to solve the aforementioned optimization problem. Some necessary simulation results are provided to demonstrate the effectiveness of the proposed radar signaling strategy

High Range and Doppler Resolution by Application of Compressed Sensing Using Low Baseband Bandwidth OFDM Radar

Multicarrier waveforms such as orthogonal frequency-division multiplexing (OFDM) found their way into radar applications in the last few years. However, currently, typically only a fraction of the large baseband bandwidth required to obtain high resolution is available in practice due to hardware limitations. In this paper, we propose a frequency-agile sparse OFDM radar processing that allows the transmission of consecutive bandwidth-reduced OFDM pulses on different carriers, and thereby covering a much larger measurement bandwidth in a measurement frame. Through joint processing of multiple narrowband pulses and compressed sensing methods, high resolution and unambiguity in the joint range-velocity profile are obtained comparable to an equivalent wideband OFDM. It shows that a baseband bandwidth of 20% of the full channel bandwidth is sufficient to reliably obtain the same result as for an equivalent wideband OFDM signal. The proposed processing scheme is validated using simulations and radar measurements at 77 GHz.

CP-based MIMO OFDM radar IRCI free range reconstruction using real orthogonal designs

In this paper, we propose a range reconstruction method for a frequency-band shared multiple-input multiple-output (MIMO) orthogonal frequency-division multiplexing (OFDM) radar with sufficient cyclic prefix (CP) by using real orthogonal designs. Compared with the application of complex orthogonal designs in our previous work, the application of real orthogonal designs can significantly reduce the number of the all-zero-valued pulses in a coherent processing interval (CPI) for each transmitter and increase the efficiency of radar transmitters. Meanwhile, it still maintains the advantages of full spatial diversity without inter-range-cell interference (IRCI). We also apply the rate-$1$ real orthogonal designs for different numbers of transmitters and pulses for range reconstruction without any idleness of radar transmitters. Simulation results are presented to illustrate the performances of the OFDM pulse design and the CP-based MIMO OFDM radar using real orthogonal designs.

MIMO-OFDM signal optimization for SAR imaging radar

This paper investigates the optimization of the coded orthogonal frequency division multiplexing (OFDM) transmitted signal in a synthetic aperture radar (SAR) context. We propose to design OFDM signals to achieve range ambiguity mitigation. Indeed, range ambiguities are well known to be a limitation for SAR systems which operates with pulsed transmitted signal. The ambiguous reflected signal corresponding to one pulse is then detected when the radar has already transmitted the next pulse. In this paper, we demonstrate that the range ambiguity mitigation is possible by using orthogonal transmitted wave as OFDM pulses. The coded OFDM signal is optimized through genetic optimization procedures based on radar image quality parameters. Moreover, we propose to design a multiple-input multiple-output (MIMO) configuration to enhance the noise robustness of a radar system and this configuration is mainly efficient in the case of using orthogonal waves as OFDM pulses. The results we obtain show that OFDM signals outperform conventional radar chirps for range ambiguity suppression and for robustness enhancement in 2 ×2 MIMO configuration.

Orthogonal frequency division multiplexing phenomenology: recognition of canonical scatterers using flat spectra OFDM pulses

In this study, the authors present a novel approach to characterise scattering centres from their radar return using specially designed waveforms. The widely accepted scattering model derived from the geometrical theory of diffraction is considered. They show how the use of flat spectrum orthogonal frequency division multiplexing pulses can help discriminating between the various scattering mechanisms. The technique, which assumes prior information about the target runs into two steps. The first step consists of designing pulses of appropriate length to mitigate intersymbol interference when several scatterers compose the target. In the second step, they calculate the spectrum of the received echo and estimate the slope of this spectrum, whose value is used to infer the scatterer type. Eventually, they assess the sensitivity of this approach with respect to additive white Gaussian noise in terms of the overall probability of correct classification and show that an integration technique can help improve the classification rate even in low signal-to-noise ratio conditions.

A novel range-Doppler imaging algorithm with OFDM radar

Traditional pulse Doppler radar estimates the Doppler frequency by taking advantage of Doppler modulation over different pulses and usually it requires a few pulses to estimate the Doppler frequency. In this paper, a novel range-Doppler imaging algorithm based on single pulse with orthogonal frequency division multiplexing (OFDM) radar is proposed, where the OFDM pulse is composed of phase coded symbols. The Doppler frequency is estimated using one single pulse by utilizing Doppler modulation over different symbols, which remarkably increases the data update rate. Besides, it is shown that the range and Doppler estimations are completely independent and the well-known range-Doppler coupling effect does not exist. The effects of target movement on the performances of the proposed algorithm are also discussed and the results show that the algorithm is not sensitive to velocity. Performances of the proposed algorithm as well as comparisons with other range-Doppler algorithms are demonstrated via simulation experiments.

Investigations on OFDM Signal for Range Ambiguity Suppression in SAR Configuration

This paper presents an opportunity to cancel range ambiguities in synthetic aperture radar (SAR) configuration. One of the limitations of SAR systems is the range ambiguity phenomenon that appears with long delayed echoes. The reflected signal corresponding to one pulse is detected when the radar has already transmitted the next pulse. Thus, this signal is considered as an echo from the next pulse. This paper investigates the opportunity of coding the transmitted pulses using an orthogonal frequency-division multiplexing pulse. The results show that coded-OFDM signals outperform conventional chirp signal and make it possible to relax constraints placed upon the pulse repetition frequency.

An improved OFDM chirp waveform used for MIMO SAR system

Special attention has been devoted to multi-input multi-output (MIMO) synthetic aperture radar (SAR) systems in recent years. The applications of MIMO SAR systems which involve 3D imaging, highresolution wide-swath remote sensing, and multi-baseline interferometry are seriously limited to the orthogonal waveforms. Although orthogonal frequency division multiplexing (OFDM) chirp waveforms can be used for MIMO SAR systems to avoid intra-pulse interferences, there is a small frequency shift between the transmitted OFDM pulses. This vulnerable shift, which can not only affect the waveform orthogonality, but also introduce residual phase error, renders the OFDM waveforms impractical. In this paper, an improved OFDM chirp waveform which works without the mentioned shift is presented, along with the novel modulation and efficient demodulation procedures. Comparison between the improved and the conventional OFDM chirp waveforms is detailed. The influence of random noise, quantization error, and Doppler shift on the orthogonality of OFDM waveform is also investigated in this paper. Theoretical analysis and simulation results illustrate the feasibility of this waveform scheme.

Fast S-Parameter Calculation Technique for Multi-Antenna System Using Temporal-Spectral Orthogonality for FDTD Method

This paper proposes an S-parameter analysis method that uses simultaneous excitation for multi-antenna systems. In this method, OFDM (Orthogonal Frequency Division Multiplexing) and CI (Carrier Interferometry) pulse generation schemes are employed for maintaining the orthogonality among the excited signals. In OFDM excitation schemes, the characteristics of the neighboring antennas can be calculated by assigning different frequency subcarriers exclusively. CI enables the simultaneous verification of the antennas distant enough since this method can provide temporal orthogonality. Combining these two methods yields the simultaneous analyses of array antennas with both narrow and wide element spacing. The simulation of a 2×2 multi-antenna shows that the results of the proposed method agree well with those of the conventional method even though its computation speed is more 4 times that of the conventional method.

LDPC coding proposal for pulsed-OFDM modulation for WPAN systems using UWB communication in indoor propagation channels

In this paper, we describe a combined approach where low density parity check (LDPC) codes are used to reduce the complexity and power consumption of pulsed orthogonal frequency-division multiplexing (pulsed-OFDM) ultra-wideband (UWB) systems. The proposed system will use LDPC codes to achieve higher code rates without using convolution encoding and puncturing thereby reducing the complexity and power consumption of pulsed-OFDM system. The LDPC-pulsed-OFDM system will achieve channel capacity with different code rates and will have good performance in different channel fading scenarios. The proposals from pulsed OFDM system is used where pulsed signals could spread the frequency spectrum of the OFDM signal. The performance of LDPC-pulsed-OFDM system for wireless personal area networks (WPAN) is analysed for different UWB indoor propagation channels (CM3 and CM4) provided by the IEEE 802.15.3a Standard activity committee. To establish this, we present a design of LDPC-pulsed-OFDM system using the digital video broadcasting-satellite-second generation (DVB-S2) standard and provide the simulation results for the different code rates supported by LDPC codes.

Pulsed-OFDM Modulation for Ultrawideband Communications

In this paper, we describe a novel approach for reducing the power consumption and complexity of a multiband orthogonal frequency-division multiplexing (MB-OFDM) ultrawideband (UWB) system by applying ideas from pulsed UWB systems. The approach is quite general and applicable to many other systems. Unlike the MB-OFDM system, the enhancement that we propose uses pulses with duty cycles of less than 1 as the amplitude shaping pulse of orthogonal frequency-division multiplexing (OFDM) modulation. Pulsating OFDM symbols spread the spectrum of the modulated signals in the frequency domain, leading to a spreading gain that is equal to the inverse of the duty cycle of the pulsed subcarriers. We study the spectral characteristics of pulsed OFDM and the added degrees of diversity that it provides. We show that pulsed-OFDM signals can easily be generated by either upsampling an equivalent OFDM baseband signal with a reduced number of carriers or by replacing the digital-to-analog converter (DAC) of a normal MB-OFDM transmitter with a low-duty-cycle DAC. We establish that a pulsed-OFDM receiver can fully exploit the added diversity without using Rake receivers. It is shown that, while pulsed OFDM has superior or comparable performance to MB-OFDM in multipath fading channels, it also has intrinsic low-complexity and power consumption advantages compared with MB-OFDM. To establish this fact, we describe an example design for the IEEE 802.15.3a Standard and present full simulation results for the UWB indoor propagation channels provided by the IEEE 802.15.3a Standard activity committee.

Spectral precoding for rectangularly pulsed OFDM

Spectrally precoded orthogonal frequency-division multiplexing (OFDM) is a promising rectangularly pulsed OFDM signaling format which can provide very small power spectral sidelobes, while allowing for efficient implementation by fast Fourier transform and guard interval insertion. In this paper, general constraints on spectral precoding are developed for OFDM signals with zero padding (ZP-OFDM) or cyclic prefix (CP-OFDM) to warrant the desirable spectral property that the power spectral sidelobes decay asymptotically as f <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-2K-2</sup> , where K is a preassigned positive integer. In accordance with the constraints, block partitioning is adopted to construct a general signaling format to facilitate the precoder design of the spectrally precoded CP-OFDM that can provide fast decaying sidelobes. New correlative and orthogonal precoders are also devised so that the desirable spectral property of fast sidelobe decaying is achieved with spectrally precoded ZP-OFDM and CP-OFDM signals.

Spectrally Precoded OFDM

By bilinearly transforming the rectangularly pulsed multicarrier basis signals, new basis sets containing full-response continuous basis signals are developed for constructing spectrally efficient orthogonal frequency-division multiplexing (OFDM) signals with or without cyclic prefix (CP) or zero padding (ZP). Both multiple-product and linear-combination formats are presented for these basis sets. In the multiple-product format, the developed full-response basis signals are shown to be zero-valued at interval edges, and thus can be used to construct continuous-phase OFDM signals. It is analytically shown that the constructed continuous-phase OFDM signals exhibit relatively small power spectral sidelobes which fall off as f <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-4</sup> , and can thus provide much higher spectral efficiency than the traditional rectangularly pulsed OFDM signal. In the linear-combination format, the proposed basis signals are shown to be the linear combinations of rectangularly pulsed multicarrier basis signals, and thereby allow for the efficient realization of fast Fourier transform (FFT). Specifically, a spectrally precoded signaling structure is developed in conjunction with inverse FFT and guard insertion to construct continuous-phase OFDM signals with or without CP or ZP. The corresponding spectral decoders are also developed to enable zero-forcing (ZF) demodulation for spectrally precoded OFDM. With the zero-forcing demodulation, the spectrally precoded OFDM schemes are shown to outperform in average error-rate characteristics the conventional rectangularly pulsed and correlatively coded OFDM schemes on various delay-spread channels