Optical True Time Delay Line Research Articles

A microwave photonic radio frequency memory with tunable delay resolution and Doppler frequency shift

Radar target simulation is essential for radar development. In this paper, a microwave photonic radio frequency memory (RFM) is proposed and experimentally verified. The input radio frequency (RF) signals are delayed and stored in a recirculating loop with a 4-bit binary optical true time delay line (OTTDL), which enables the achievement of the tunable delay resolution and multiple replications. The Doppler frequency shift (DFS) of the delayed signals is achieved by a Mach-Zehnder modulator (MZM) and two cascaded acousto-optic modulators (AOMs), which facilitate a wide tuning range, high precision, and a high spurious suppression ratio (SSR). The experimental results demonstrate that the system has 16 distinct delay resolutions ranging from 0.045 us to 7.576 us. Furthermore, 30 circulations are achieved in the test, indicating that the theoretical maximum storage time is approximately 225 us. Additionally, the frequency shift for 1 GHz–18 GHz RF pulse signals can be tuned over a range of 10 Hz to 10 MHz, with a SSR exceeding 40 dB.

Continuously tunable silicon optical true-time delay lines with a large delay tuning range and a low delay fluctuation.

On-chip switchable optical true-time delay lines (OTTDLs) feature a large group delay tuning range but suffer from a discrete tuning step. OTTDLs with a large delay tuning range and a continuous tuning capability are highly desired. In this paper, we propose and experimentally demonstrate a silicon-based broadband continuously tunable OTTDL comprising a 7-bit delay line and a switch-based continuously tunable delay line. The group delay of the entire OTTDL can be continuously tuned from 0 to 1020.16 ps. A delay error within -1.27 ps to 1.75 ps, and a delay fluctuation of less than 2.69 ps in the frequency range of 2∼25 GHz are obtained. We analyze the causes of the delay fluctuation and its influence on beamforming. Moreover, we also propose a simplified non-invasive calibration method that can significantly reduce the complexity of the delay state calibration and can be easily extended to delay lines with more stages of optical switches. The high performance of our OTTDL chip and the calibration method drive practical applications of integrated OTTDLs.

Cladding modulated silicon waveguide Bragg grating with TM-polarized light for optical true time delay line

An optical true time delay line (OTTDL) is an essential component in optical signal processing. A Bragg grating structure is usually employed in OTTDL design, which makes it possible to achieve a slow-light effect. Here, we present the design and experimental demonstration of a cladding modulated waveguide Bragg grating (CMWBG) that supports transverse magnetic polarization for OTTDL application. In contrast to traditional waveguide Bragg gratings that support transverse electric polarization, the proposed structure has low propagation loss and high fabrication tolerance characteristics. The slow-light effect of the CMWBG was experimentally demonstrated with a high group index value. An averaged maximum group delay value of up to 84.4 ps was achieved at a length of 1 mm CMWBG, and a tuning range of about 81.4 ps was obtained.

On-chip optical true time delay lines based on subwavelength grating waveguides

On-chip optical true time delay lines based on subwavelength grating waveguides

True Time Delay Optical Beamforming Network Based on Hybrid Inp-Silicon Nitride Integration

We demonstrate a broadband and continuously tunable 1×4 optical beamforming network (OBFN), based on the hybrid integration of indium phosphide (InP) components in the silicon nitride (Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> ) platform. The photonic integrated circuit (PIC) comprises a hybrid InP-Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> external cavity laser, a pair of InP phase modulators, a Si <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sub> optical single-sideband full carrier (SSBFC) filter followed by four tunable optical true time delay lines (OTTDLs), and four InP photodetectors. Each OTTDL consists of eight cascaded thermo-optical micro-ring resonators (MRRs) that impose tunable true time delay on the propagating optical signals. The OBFN-PIC is designed to facilitate the steering of a microwave signal with carrier frequency up to 40 GHz over a continuous set of beam angles. We evaluate the performance of the OBFN-PIC to handle and process microwave signals, measuring the link gain, the noise figure (NF), and the spurious-free dynamic range (SFDR) parameters. Moreover, we assess its beamforming capabilities assuming that the OBFN-PIC is part of a wireless system operating in the downlink direction and feeds a multi-element antenna array. Using microwave signals at 5 and 10 GHz with quadrature amplitude modulation (QAM) formats at 500 Mbaud, we evaluate the performance of the OBFN-PIC under various configurations. We show that error-free performance can be achieved at both operating frequencies and for all the investigated beam angles ranging from 45° to 135°, thus validating its potential for high-quality beamforming performance.

Reflective coupled microring resonators for reconfigurable photonic systems: Performance analysis

We propose reflective type triple coupled microring resonators (TCMMRs) for reconfigurable photonic based systems. We have developed an analytical model and analyzed its useful performance characteristics. The TCMMRs based device exhibits a wide range of performance characteristics such as multi-band filtering, optical logical operations, and optical true-time delay lines. Reconfigurable multiple resonances and their splitting features associated with the device provide useful filtering performance characteristics such as high out-of-band rejection, flat-top bandwidth, and near to ideal shape factor. The device can perform multiple functions such as bandpass, bandstop, and notch filtering with a good performance. Unlike two input narrowband logical operations demonstrated in the literature, our proposed device can perform as three-input optical logical operator, and it can switch wideband microwave frequency signals optically. Moreover, the device exhibits wideband flat top group delay response. It carries out delay tuning using a single variable coupling coefficient which simplifies the complexity of the tuning encountered in binary tree-structured optical beamforming networks based on conventional microring resonators.

On-chip optical true time delay lines based on subwavelength grating waveguides.

An optical true time delay line (OTTDL) is a fundamental building block for signal processing applications in microwave photonics and optical communications. Here, we experimentally demonstrate an index-variable OTTDL based on an array of 40 subwavelength grating (SWG) waveguides in silicon-on-insulator. Each SWG waveguide in the array is 34 mm long and arranged in a serpentine manner; the average incremental delay between waveguides is about 4.7 ps, and the total delay between the first and last waveguides is approximately 181.9 ps. The waveguide array occupies a chip area of ∼6.5mm×8.7mm=56.55mm2. The proposed OTTDLs bring potential advantages in terms of compactness as well as operation versatility to a variety of microwave signal processing applications.

A wideband 1[formula omitted]4 optical beam-forming chip based on switchable optical delay lines for Ka-band phased array

Comparing with electronic beam forming, integrated optical beam forming is very promising for optical controlled phase array system, because much broader band beam steering can be achieved without the beam squint effect. The single channel optical true time delay lines based on the cascade microring resonators and switched optical delay waveguides have been extensively investigated. The optical beam forming chip based on multi-channel microring resonators have also been demonstrated, however only limited working bandwidth were obtained due to their inherent tradeoff between the delay and bandwidth. The bandwidth limitation can be overcome by using integrated optical beam forming chip composed of switched optical delay waveguides, which has not been demonstrated and evaluated. Here, a 1×4 optical beamforming chip with four integrated switchable delay lines units designed to control the Ka-band phased antenna arrays is proposed and demonstrated experimentally. The maximum delay of 96 ps with a delay increment about 3.02 ps/stage was obtained, which is in accordance with the design well. Based on the measured delay times, the directional diagrams of the optical beamforming network were simulated and beam angle coverage of 90° can be achieved. Furthermore, a magnitude response experiment was carried out to evaluate the performance of the optical beam forming chip, and a remarkable working bandwidth of 29 GHz was achieved.

Silicon integrated microwave photonic beamformer

Optical beam-forming networks (OBFNs) based on optical true-time delay lines (OTTDLs) are well known as the promising candidate for solving the bandwidth limitation of traditional electronic phased array antennas (PAAs) due to beam squinting. Here we report, to the best of our knowledge, the first monolithic 1 × 8 microwave photonic beamformer, based on switchable OTTDLs on the silicon-on-insulator platform. The chip consists of a modulator, an eight-channel OBFN, and eight photodetectors, thus including hundreds of active and passive components in total. It has a wide operating bandwidth from 8 to 18 GHz, which is almost two orders larger than that of electronic PAAs. The beam can be steered to 31 distinguishable angles in the range from − 75.51 ∘ to 75.64°, based on the beam pattern calculation with the measured radiofrequency response. The response time for beam steering is 56 µs. These results represent a significant step toward the realization of integrated microwave photonic beamformers that can satisfy compact-size and low-power consumption requirements for the future radar and wireless communication systems.

Integrated Wavelength-Tuned Optical mm-Wave Beamformer With Doubled Delay Resolution

Integrated optical true time delay lines attract lots of attention for optically controlled mm-wave beam steering due to its low-loss/broadband performance and stable/compact system architecture. However, for remotely-controlled networks, the techniques that require local-site actively-tuned elements would make the network control more complicated. A passive design using wavelength-tuning is regarded as a promising candidate. In this paper, an integrated wavelength-tuned optical mm-wave beamformer with doubled delay resolution is proposed and demonstrated in a generic InP platform. A bidirectional looped-back arrayed waveguide grating (AWG) module acts as the stepwise tunable delay unit. By introducing an extra AWG router for delay mode (positive/negative) selection and a bidirectional optical interface, a pure λ-tuned, resolution-doubled optical delay network is realized without using any active component (e.g. heaters, current injection) at the local site. This photonic passive design is more beneficial to the remotely-controlled mm-wave beam steering system. Furthermore, the AWG router potentially allows multi-port wavelength switching to support the scaling-up of the network. The fabrication-caused delay error of <; 1.1 ps is experimentally verified on-chip. A further proof-of-concept 38-GHz fiber-wireless beam steering system with a 186° angular steering is experimentally demonstrated using QAM-4 modulation. Accurate mm-wave phase shifts originated from the proposed optical beamformer are obtained, which proves the effectiveness of the tunable integrated beamformer.

A Seven Bit Silicon Optical True Time Delay Line for Ka-Band Phased Array Antenna

A seven-bit optical true time delay unit with a delay tuning increment of 1.42 ps was designed and fabricated on silicon photonics platform, which can be utilized in Ka-band phased array antenna systems. The delay unit consists of eight thermo-optical switches and seven waveguide delay lines with different lengths. By manipulating the states of the thermo-optical switches, 128 stages of discrete time delays varying from 0 to 191.37 ps has been obtained with low average power consumption of 178.77 mW. Besides, the integrated delay unit was fabricated on the silicon-on-insulator chip that has a very compact footprint of 7.4 mm × 1.8 mm. In addition, as the waveguide delay dependence on the modulation frequency is very limited and can be neglected, the proposed delay unit should process a large bandwidth that allows it to be utilized in microwave applications with abundant bandwidth.

Reconfigurable RF notch filter based on an integrated silicon optical true time delay line

The development of radio-frequency (RF) filters with bandwidth reconfigurability and frequency tunability in the MHz range is increasingly important to broadband wireless communication and radar systems. In this paper, we demonstrate a reconfigurable RF filter based on a silicon integrated optical true time delay line (OTTDL). The OTTDL is a four-path parallel structure with the reconfiguration enabled by thermo-optic Mach–Zehnder interferometer switches. By controlling the power splitting ratio of the switches, three different orders of finite impulse response filters with a variable bandwidth are realized. The bandwidth can be varied from 180.9 MHz to 662.0 MHz and the center frequency can be tuned in one free-spectral range up to 1 GHz.

Scalable and reconfigurable true time delay line based on an ultra-low-loss silica waveguide.

A scalable and reconfigurable on-chip optical true time delay line consisting of Mach-Zehnder interferometer (MZI) switches and delay waveguides is proposed and demonstrated with the ultra-low-loss silica waveguide platform. The MZI switches provide the reconfiguration of the light traveling paths and hence different delays. Our proposed structure can be easily scaled to an M bit delay line with a slight increase in dimensions. The footprint of our fabricated 1bit delay line is 33 mm×13 mm (length×width) and can provide a delay of 6.0ps with an insertion loss of 1.2dB at the operating wavelength of 1550nm, while the footprint of the 4bit delay line is 43 mm×14 mm and can provide a discrete delay tuning from 6.0 to 90.2ps with a delay deviation lower than 0.2ps and a tuning response time of 0.84ms. The insertion losses are lower than ∼2.34 dB, and the extinction ratios are greater than 20.42dB. The average switching power is ∼132.6 mW. Our proposed optical true time delay lines could find applications for optical beamforming in phased array antennas.

On-chip optical true time delay lines featuring one-dimensional fishbone photonic crystal waveguide

In this paper, we present on-chip optical true time delay lines based on slow light one-dimensional (1D) fishbone photonic crystal waveguides (FPCWs). The structural slow light is generated by modulating the index guided optical mode with periodically arranged sidewalls along the propagation direction. Due to the reduced mode overlap with the rough etched surface, the propagation loss of the 1D FPCW is significantly reduced compared to the two-dimensional photonic crystal waveguide. A delay time of 65 ps/mm is observed experimentally.

Subwavelength grating waveguide devices in silicon-on-insulators for integrated microwave photonics (Invited Paper)

We provide an overview of our recent work on developing subwavelength grating (SWG) waveguide devices as an enabling technology for integrated microwave photonics. First, we describe wavelength-selective SWG waveguide filters, including ring resonators, Bragg gratings, and contradirectional couplers. Second, we discuss the development of an index variable optical true time delay line that exploits spatial diversity in an equal-length waveguide array. These SWG waveguide components are fundamental building blocks for realizing more complex structures for advanced microwave photonic signal processing.

Silicon Photonics for Microwave Photonics Applications

We provide an overview of recent work on developing integrated microwave photonic subsystems in silicon photonics for generating chirped microwave waveforms as well as for providing optical true time delay. First, we describe on-chip spectral shapers based on Bragg gratings (BGs), including a distributed Fabry–Perot cavity, a Michelson interferometer incorporating identical chirped BGs, and a Sagnac loop incorporating a chirped BG, for use in wavelength-to-time mapping systems. The performance of these on-chip spectral shapers is compared to those based on microring resonators as well as fiber or free-space configurations. Second, we consider the development of an index variable optical true time delay line (OTTDL) using subwavelength grating (SWG) waveguides. For SWG waveguides of the same length, incremental delays can be obtained by tailoring the group index via control over the duty cycle. We compare the performance of SWG waveguide OTTDLs to other length variable implementations in silicon.

Subwavelength grating enabled on-chip ultra-compact optical true time delay line.

An optical true time delay line (OTTDL) is a basic photonic building block that enables many microwave photonic and optical processing operations. The conventional design for an integrated OTTDL that is based on spatial diversity uses a length-variable waveguide array to create the optical time delays, which can introduce complexities in the integrated circuit design. Here we report the first ever demonstration of an integrated index-variable OTTDL that exploits spatial diversity in an equal length waveguide array. The approach uses subwavelength grating waveguides in silicon-on-insulator (SOI), which enables the realization of OTTDLs having a simple geometry and that occupy a compact chip area. Moreover, compared to conventional wavelength-variable delay lines with a few THz operation bandwidth, our index-variable OTTDL has an extremely broad operation bandwidth practically exceeding several tens of THz, which supports operation for various input optical signals with broad ranges of central wavelength and bandwidth.

应用于相控阵雷达的光子晶体慢光波导光实时延迟线

应用于相控阵雷达的光子晶体慢光波导光实时延迟线

Seven-bit reconfigurable optical true time delay line based on silicon integration: erratum

Seven-bit reconfigurable optical true time delay line based on silicon integration: erratum

Seven-bit reconfigurable optical true time delay line based on silicon integration.

We design, fabricate, and characterize a 7-bit reconfigurable optical true time delay line consisting of Mach-Zehnder interferometer (MZI) switches on the silicon photonics platform. Variable optical attenuators (VOAs) are embedded to suppress the inter-symbol crosstalk caused by the finite extinction ratio of switches. The device can provide a maximum of 1.27 ns delay with a 10 ps resolution over a wide wavelength range. Eye diagram measurement of a 25 Gbps 2(51)-1 pseudo-random bit sequence (PRBS) signal reveals the power penalties only increase 0.17 dB and 0.77 dB after transmission through the shortest (reference) and the longest (1.27 ns delay) paths, respectively.