Optical Image Correlation Research Articles

Evaluation of localized mechanical properties of modified N50 welded joints at cryogenic temperature through a digital image correlation technique

The modified N50 austenitic stainless steel has been determined to be applied as the superconducting magnet supporting material of the Chinese Fusion Engineering Test Reactor (CFETR), especially the jacket material of the CICCs of both the TF coils and the CS coils and the case material of the TF coils, which inevitably requires welding connection. The welding process generally results in welding defects as well as degradation of cryogenic mechanical properties of metallurgical inhomogeneous zones. However, limited research has been reported to demonstrate the distinct localized performance of these zones at cryogenic temperature. The present paper presents an approach to characterize localized mechanical properties of the modified N50 welds at both room temperature (300 K) and cryogenic temperature (6 K). We identified the welding zone (WZ) through metallographic analysis and then the boundaries of the heat-affected zone (HAZ) were recognized by hardness measurements at room temperature. Finally, the localized optical digital image correlation (DIC) technique was used to obtain the localized yield strength Rp0.2 and percentage extension e of the WZ, the HAZ, and the base metal (BM) at both room and cryogenic temperature, of which the observed trend is verified through comparison with that of hardness measurements at room temperature. The technique proposed provides the localized measurement of cryogenic tensile properties of weld metals and also presents experimental data on different zones of the modified N50 welded joints as a jacket material for the next-generation fusion reactors.

Strain localisation and grain boundary-mediated deformation in pure titanium at low and high temperatures: In-situ optical microscopy and digital image correlation

Heterogeneous deformation occurs between grains in polycrystalline α-titanium. Understanding the role of temperature in local deformation is essential for its applications in extreme environments such as cryo- or high-temperature, but the underlying mechanism still remains elusive. Here we report a study of grain-scale deformation behaviour in CP-Ti plate at the temperature range from −60 °C to 280 °C. The full-field strain measurements were conducted on the tensile samples loaded parallel (RD) and transverse (TD) to the rolling direction, using in-situ optical microscopy and digital image correlation (OM-DIC). The DIC local strain maps were coupled with scanning electron microscopy and electron backscatter diffraction analysis. The grain boundary sliding and slip transfer occurred depending on the geometric relationship (i.e., deformation compatibility) between adjacent grains at 20 °C, and a micro-crack was observed at the {101‾1} twist boundary. The strain was recovered in the grains in the RD sample favourable for slip, whilst more accumulated in the grains in TD sample unfavourable for slip at 280 °C. The plasticity of grains differs with decreasing temperature to −40 °C, resulting in the presence of soft/hard grain pairs. The strong strain localisation between the soft and hard grains led to the cracking along the GBs (RD) and cross the grains (TD). Interestingly, the cracking was significantly reduced with decreasing temperature to −60 °C due probably to the temperature dependence of the plasticity of grains. The strain-hardening behaviour of α-Ti polycrystals was significantly affected by the temperature and crystal orientation dependence of grain-scale deformation mechanism.

Effect of Thermal Pre-treatment on Thermal Gradient Response of Granitic Rocks: Insights from Optical Microscopy and Digital Image Correlation

Effect of Thermal Pre-treatment on Thermal Gradient Response of Granitic Rocks: Insights from Optical Microscopy and Digital Image Correlation

Effects of preexisting dislocations on phase transition and deformation of NiTi shape memory alloy: An in situ multi-scale study

Phase transition and deformation in cold-rolled and heat-treated Ni50.6Ti49.4 alloys are explored by in situ multi-scale measurements with simultaneous X-ray diffraction and optical digital image correlation. Macroscale stress−strain curves, mesoscale strain fields and microscale X-ray diffraction peaks are obtained. Electron backscatter diffraction and transmission electron microscopy are also conducted on samples before and after tension as complements. For cold-rolled samples, since martensite nucleation is strongly associated with the widely distributed preexisting dislocations, homogeneous martensite phase transition takes place, in contrast with the localized mode in heat-treated samples. For localized phase transition, the intense growth of martensite results in clear Lüders bands. The beginning and the end of phase transition plateau on the stress−strain curve are associated with the initiation and complete propagation of Lüders bands. For the homogeneous phase transition, broad growth of martensite leads obscure Lüders bands and uniform strain fields, without any phase transition plateau. Given the initial {110}〈110〉 and {111}〈110〉 sheet textures in the heat-treated samples, different martensite variants with different preferred orientations are activated with respect to the loading directions.

Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis—Part I: Parameter identification

ObjectiveTo investigate the feasibility of optical coherence tomography (OCT)-based digital image correlation (DIC) analysis and to identify the experimental parameters for measurements of polymerization shrinkage. MethodsClass I cavities were prepared on bovine incisors and filled with Filtek Z350XT Flowable (Z350F). One OCT image of the polymerized restoration was processed to generate virtually displaced images. In addition, the tooth specimen was physically moved under OCT scanning. A DIC software analyzed these virtual and physical transformation sets and assessed the effects of subset sizes on accuracy. The refractive index of unpolymerized and polymerized Z350F was measured via OCT images. Finally, different particles (70–80 µm glass beads, 150–212 µm glass beads, and 75–150 µm zirconia powder) were added to Z350F to inspect the analyzing quality. ResultsThe analyses revealed a high correlation (>99.99%) for virtual movements within 131 pixels (639 µm) and low errors (<5.21%) within a 10-µm physical movement. A subset size of 51 × 51 pixels demonstrated the convergence of correlation coefficients and calculation time. The refractive index of Z350F did not change significantly after polymerization. Adding glass beads or zirconia particles caused light reflection or shielding in OCT images, whereas blank Z350F produced the best DIC analysis results. SignificanceThe OCT-based DIC analysis with the experimental conditions is feasible in measuring polymerization shrinkage of RBC restorations. The subset size in the DIC analysis should be identified to optimize the analysis conditions and results. Uses of hyper- or hypo-reflective particles is not recommended in this method.

Discontinuous Surface Ruptures and Slip Distributions in the Epicentral Region of the 2021 Mw7.4 Maduo Earthquake, China

Discontinuous Surface Ruptures and Slip Distributions in the Epicentral Region of the 2021 Mw7.4 Maduo Earthquake, China

High-resolution co-seismic fault offsets of the 2023 Türkiye earthquake ruptures using satellite imagery

On February 6, 2023, southern Türkiye was struck by two large earthquakes at 01:17 UTC (Mw=7.8, Pazarcık, Kahramanmaraş) and 10:30 UTC (Mw = 7.6, Elbistan, Kahramanmaraş), causing severe damage at the complex junction of the Dead Sea Fault (DSF), the Cyprus Arc and the East Anatolian Fault Zone (EAFZ). The ruptures propagated along several known strands of the southwestern termination of the EAFZ, the main Pazarcık and Karasu valley faults, and the Çardak-Sürgü fault. Here we present the high-resolution mapping of the entire coseismic surface rupture and an estimate of the rupture width, total and on-fault offset, and diffuse deformation obtained a few days to three months after the two mainshocks. The mapping is derived from image correlation of Sentinel-2 optical satellite imagery and validated with offset measurements collected on the ground. We find that the ruptures extend over lengths of 310 km and 140 km for the Mw 7.8 and Mw 7.6 mainshocks, respectively. The maximum offsets reach 7.5 ± 0.8 m and 8.7 ± 0.8 m near the epicenters of the Mw 7.8 and Mw 7.6 events, respectively. We propose a segmentation of the two ruptures based on these observations, and further discuss the location of the potential supershear rupture. The use of optical image correlation, complemented by field investigations along earthquake faults, provides new insights into seismic hazard assessment.

Coseismic slip distribution of the 2023 earthquake doublet in Turkey and Syria from joint inversion of Sentinel-1 and Sentinel-2 data: an iterative modelling method for mapping large earthquake deformation

SUMMARY Interferometric synthetic aperture radar (InSAR) decorrelation that creates great challenges to phase unwrapping has been a critical issue for mapping large earthquake deformation. Some studies have proposed a ‘remove-and-return model’ solution to tackle this problem, but it has not been fully validated yet, and therefore has rarely been applied to real earthquake scenarios. In this study, we use the 2023 Mw 7.8 and 7.6 earthquake doublet in Turkey and Syria as a case example to develop an iterative modelling method for InSAR-based coseismic mapping. We first derive surface deformation fields using Sentinel-1 offset tracking and Sentinel-2 optical image correlation, and invert them for an initial coseismic slip model, based on which we simulate InSAR coseismic phase measurements. We then remove the simulated phase from the actual Sentinel-1 phase and conduct unwrapping. The simulated phase is added back to the unwrapped phase to produce the final phase measurements. Comparing to the commonly used unwrapping method, our proposed approach can significantly improve coherence and reduce phase gradients, enabling accurate InSAR measurements. Combining InSAR, offset tracking and optical image correlation, we implement a joint inversion to obtain an optimal coseismic slip model. Our model shows that slip on the Çardak Fault is concentrated on a ∼100 km segment; to both ends, slip suddenly diminished. On the contrary, rupture on the East Anatolian Fault Zone propagated much longer as its geometry is fairly smooth. The iterative coseismic modelling method is proven efficient and can be easily applied to other continental earthquakes.

Tensile response of additively manufactured carbon/nylon joints using optical fibers and digital image correlation

ABSTRACT Additive manufacturing (AM) has gained popularity due to reduced production times of low-cost and geometrically complex structures. Due to technological constraints such as print volume, time, and thermal stability of large AM parts, adhesive joints are commonly used in assembling smaller components in large-scale polymeric structures. This work investigates the feasibility of using embedded optical fibers to monitor strain distributions within AM composite (carbon fiber/nylon) single-lap shear (SLS) joints. Internal strain distributions within the adhesive and surface strain fields of the SLS joints with AM adherends under tensile loads were obtained using optical fibers and digital image correlation, respectively. Results indicate negligible influence of optical fibers on the failure strength and axial stiffness of 3D-printed SLS joints under quasi-static loading. Higher strains were observed at the bond edges within the adhesive (using optical fiber) and the surface (using DIC) of the joints due to the rotation of the bond under loading. All specimens failed in the adherends beyond the bonded region due to their low interlaminar strength.

APPLICATION OF LUCAS-KANADE DENSE FLOW FOR TERRAIN MOTION IN LANDSLIDE MONITORING APPLICATION

Abstract. Landslides are natural hazards that can cause severe damage and loss of life. Optical cameras are a low-cost and high-resolution alternative among many monitoring systems, as their size and capabilities can vary, allowing for flexible implementation and location. Computer vision is a branch of artificial intelligence that can analyze and understand optical images, using techniques such as optical flow, image correlation and machine learning. The application of such techniques can estimate the motion vectors, displacement fields, providing valuable information for landslide detection, monitoring and prediction. However, computer vision also faces some challenges such as illumination changes, occlusions, image quality, and computational complexity. In this work, a computer vision approach based on Lucas-Kanade optical dense flow was applied to estimate the motion vectors between consecutive images obtained during landslide simulations in a laboratory environment. The approach is applied to two experiments that vary in their illumination and setup parameters to test its applicability. We also discuss the application of this methodology to images from Sentinel-2 satellite optical sensors for landslide monitoring in real-world scenarios.

AN OPTIMIZATION FRAMEWORK TO ENABLE THE MEASUREMENT OF STRAIN IN LIGAMENTS USING ULTRASOUND

AbstractObjectivesUltrasound speckle tracking is a safe and non-invasive diagnostic tool to measure soft tissue deformation and strain. In orthopaedics, it could have broad application to measure how injury or surgery affects muscle, tendon or ligament biomechanics. However, its application requires custom tuning of the speckle-tracking algorithm then validation against gold-standard reference data. Implementing an experiment to acquire these data takes months and is expensive, and therefore prohibits use for new applications. Here, we present an alternative optimisation approach that automatically finds suitable machine and algorithmic settings without requiring gold-standard reference data.MethodsThe optimisation routine consisted of two steps. First, convergence of the displacement field was tested to exclude the settings that would not track the underlying tissue motion (e.g. frame rates that were too low). Second, repeatability was maximised through a surrogate optimisation scheme. All settings that could influence the strain calculation were included, ranging from acquisition settings to post-processing smoothing and filtering settings, totalling &gt;1,000,000 combinations of settings. The optimisation criterion minimised the normalised standard deviation between strain maps of repeat measures. The optimisation approach was validated for the medial collateral ligament (MCL) with quasi-static testing on porcine joints (n=3), and dynamic testing on a cadaveric human knee (n=1, female, aged 49). Porcine joints were fully dissected except for the MCL and loaded in a material-testing machine (0 to 3% strain at 0.2 Hz), which was captured using both ultrasound (&gt;14 repeats per specimen) and optical digital image correlation (DIC). For the human cadaveric knee (undissected), 3 repeat ultrasound acquisitions were taken at 18 different anterior/posterior positions over the MCL while the knee was extended/flexed between 0° and 90° in a knee extension rig. Simultaneous optical tracking recorded the position of the ultrasound transducer, knee kinematics and the MCL attachments (which were digitised under direct visualisation post testing). Half of the data collected was used for optimisation of the speckle tracking algorithms for the porcine and human MCLs separately, with the remaining unseen data used as a validation test set.ResultsFor the porcine MCLs, ultrasound strains closely matched DIC strains (R2 &gt; 0.98, RMSE &lt; 0.59%) (Figure 1A). For the human MCL (Figure 1B), ultrasound strains matched the strains estimated from the optically tracked displacements of the MCL attachments. Furthermore, strains developed during flexion were highly correlated with AP position (R = 0.94) with strains decreasing the further posterior the transducer was on the ligament. This is in line with previously reported length change values for the posterior, intermediate and anterior bundles of the MCL.ConclusionsUltrasound speckle tracking algorithms can be adapted for new applications without ground-truth data by using an optimisation approach that verifies displacement field convergence then minimises variance between repeat measurements. This optimisation routine was insensitive to anatomical variation and loading conditions, working for both porcine and human MCLs, and for quasi-static and dynamic loading. This will facilitate research into changes in musculoskeletal tissue motion due to abnormalities or pathologies.Declaration of Interest(a) fully declare any financial or other potential conflict of interest

Investigation of frequency-dependent fatigue crack growth behavior in perfluorosulfonic-acid membrane: In-situ experiment, constitutive modeling and crack growth prediction

Fatigue crack growth behavior of perfluorosulfonic-acid membrane is investigated under distinct loading frequencies. The evolution of cyclic plastic zone (CPZ) is traced based on in-situ optical microscopy testing and digital image correlation (DIC) technique. The crack tip deformation process is directly observed by in-situ scanning electron microscope (SEM). The experimental results show that fatigue cracks experiencing a higher loading frequency display a comparatively reduced propagation rate. The CPZ can be solely used to interpret the fatigue crack growth rate variation under different loading frequencies. The crack-front microspores are easily formed under lower loading frequency due to the enhancement of near-tip plasticity deformation. Then, a cyclic elastic-viscoplastic constitutive model is developed, which successfully capture the mechanical behavior of the membrane. Finally, based on the plastically dissipated energy, a numerical method incorporated with the developed material’s constitutive relationship is established, which gives reasonable prediction of fatigue crack growth under various loading frequencies.

Stability of Three-Dimensional Printed Custom-Made Metaphyseal Cone for Tibial Bone Defects Reconstruction: A Finite Element Analysis and Biomechanical Study.

The reconstruction of bone defects in tibial revision knee arthroplasty is challenging. In this study, we evaluated the primary stability of a novel three-dimensional (3D)-printed custom-made metaphyseal cone for Anderson Orthopedic Research Institute (AORI) IIb or III bone defect reconstruction in tibial revision knee arthroplasty using the combination of finite-element analysis and biomechanical experiments. In the finite-element analysis, AORI II b and III medial tibial bone defects were designed at varying depths. A novel 3D-printed custom-made metaphyseal cone was designed and used to reconstruct the bone defect with or without a stem in simulated revision total knee arthroplasty (RTKA). A no-stem group and a stem group were established (based on whether a stem was used or not). Von Mises stress and micromotion were calculated with varying depths of bone defects, ranging from 5 mm to 35 mm, and then micromotions at the bone-implant interface were calculated and compared with the critical value of 150 μm. In the biomechanical experiment, the no-stem group was used, and the same bone defects were made in four synthetic tibias using patient-specific instruments. Micromotions at the bone-implant interface were investigated using a non-contact optical digital image correlation system and compared with the critical value of 150 μm. When the bone defect was <30 mm, micromotions at the bone-implant interface in the finite-element analysis were all below 150 μm both in the stem groups and no-stem groups, whereas those in the biomechanical experiment were also below 150 μm in the no-stem group. The 3D-printed custom-made metaphyseal cone in RTKA has excellent primary stability and does not require stems in reconstructing tibial AORI type IIb or III bone defects with a depth of <30 mm.

Structure and Mechanical Behavior of Heat-Resistant Steel Manufactured by Multilayer Arc Deposition

The manuscript demonstrates the structure and the mechanical behavior of a material manufactured by multilayer arc deposition. Three-dimensional printing was performed using OK Autrod 13.14 wire on a substrate of heat-resistant 12Cr1MoV steel in the standard gas metal arc welding (GMAW) mode and in the coldArc mode with reduced heat input. The printed materials have 40–45% higher strength and 50–70% lower ductility compared to the substrate. The microhardness of the printed materials is higher than the substrate, but it is reduced at the transition regions between the deposited layers. These regions have been studied using optical microscopy and digital image correlation. Such layer boundaries are an additional factor in reducing the plasticity of the material. The increase in strength and decrease in ductility for printed materials compared to the ferrite–pearlitic substrate is associated with a high cooling rate and the formation of a mixture of acicular and allotriomorphic ferrite, which have higher hardness. The structure of the obtained layers along the height is non-uniform and undergoes changes during the deposition of new layers. The main difference between the 3D printing modes is the reduced heat input in the coldArc mode, which results in less heat accumulation and faster cooling of the wall. Thus, a more dispersed and solid structure was formed compared with GMAW. It was concluded that the cooling rate and the level of heat input are the main factors affecting the structure formation (martensitic, bainitic, or ferritic), the height and quality of the surface, and the mechanical properties of the printed wall.

Vector Angular Continuity in the Fusion of Coseismic Deformations at Multiple Optical Correlation Scales.

As one of the common techniques for measuring coseismic deformations, optical image correlation techniques are capable of overcoming the drawbacks of inadequate coherence and phase blurring which can occur in radar interferometry, as well as the problem of low spatial resolution in radar pixel offset tracking. However, the scales of the correlation window in optical image correlation techniques typically influence the results; the conventional SAR POT method faces a fundamental trade-off between the accuracy of matching and the preservation of details in the correlation window size. This study regards coseismic deformation as a two-dimensional vector, and develops a new post-processing workflow called VACI-OIC to reduce the dependence of shift estimation on the size of the correlation window. This paper takes the coseismic deformations in both the east-west and north-south directions into account at the same time, treating them as vectors, while also considering the similarity of displacement between adjacent points on the surface. Herein, the angular continuity index of the coseismic deformation vector was proposed as a more reasonable constraint condition to fuse the deformation field results obtained by optical image correlation across different correlation window. Taking the earthquake of 2021 in Maduo, China, as the study area, the deformation with the highest spatial resolution in the violent surface rupture area was determined (which could not be provided by SAR data). Compared to the results of single-scale optical correlation, the presented results were more uniform (i.e., more consistent with published results). At the same time, the proposed index also detected the strip fracture zone of the earthquake with impressive clarity.

Digital Image Correlation Analysis of Strain Fields in Fibre-Reinforced Polymer–Matrix Composite under ±45° Off-Axis Tensile Testing

This study presents an experimental investigation of an in-plane shear of a glass lamina composite using a ±45° off-axis tension test. Typically, the shear stress curve, shear modulus, and in-plane shear strength for composite lamina-type materials are identified. Previous research indicated that a loading rate affects the strength of this composite. This study extends the existing literature by utilising a non-contact optical digital image correlation (DIC) method to measure strain distribution during the test. Two cross-head displacement rates were examined. The obtained strain maps reveal an uneven distribution resembling fabric texture. As the deformation progresses, the differences in the strain pattern increase. Subsequently, a quantitative analysis of the differences between regions with extreme (minimum and maximum) strain values and regions with average values was conducted. Based on these measurements, shear stress–strain curves, indicating variations in their courses, were constructed. These differences may reach several percent and may influence the analysis of numerical simulations. The DIC results were validated using strain gauge measurements, a commonly utilised method in this test. It was demonstrated that the location of the strain gauge installation impacts the results. During the tests, the occurrence of multiple microcracks in the resin was observed, which can contribute to the nonlinearity observed in the shear stress–shear strain curve.

Mode-III fracture toughness measurements of foam-cored sandwich composites using a constrained Shear-Torsion-Bending specimen

This work presents a constrained version of the Shear-Torsion-Bending (STB) test fixture, specially developed for testing of the mode-III face/core fracture toughness of sandwich specimens. Compared to the traditional STB test fixture, the free end of the specimen is now constrained between two support rollers, restraining the twisting deformation of the specimen resulting from the mode-III shear forces. The constrained STB test fixture was applied for mode-III fracture characterization of sandwich specimens with longitudinal slits and consisting of E-glass/epoxy face sheets and Divinycell PVC foam cores. Three density classes of the foam material were considered and tested, that is, H45, H100, and H160. Furthermore, two core thicknesses were tested for the H160 cored specimens. The experimental results from the constrained STB test method show that stable crack growth is obtained without kinking into the core. However, post-mortem investigations showed that longitudinal 45° tension cracks in the core just below the face/core interface occurred, before interface crack opening. Consequently, an apparent mode-III fracture toughness was computed using a three-dimensional Finite Element (FE) model in conjunction with the Crack Surface Displacement Extrapolation (CSDE) mode-mixity method and an optical Digital Image Correlation (DIC) based crack propagation method. Finally, based on the experimental observations presented in this paper, a general discussion of the existence of pure mode-III face/core interface propagation in foam-cored sandwich composites in relation to core and face/core bond strength is included.

High-speed Digital Image Correlation (DIC) for measuring deformation and vibration of fast rotating fan blades

Due to ecological requirements, the bypass-ratio of future civil turbofan engines will be increased. This leads to ultra-high bypass ratio (UHBR) engines, which bring in new challenges concerning the blade material, structural integration, and aeroelastic behaviour of the fan. The ambition of the project Composite fan Aerodynamic, Aeroelastic, and Aeroacoustic Validation Rig (CA3ViAR) is to design and test an open-test-case fan that experiences instability mechanisms, which are representative for UHBR fans of civil aircrafts. The optical measurement technique Digital Image Correlation (DIC) allows for the spatial measurement of deformations. The aim is to apply this technique to measure rotor blade deformation under loading and its vibration due to aeroelastic phenomena to get a better understanding of the structural and aeroelastic behaviour of the composite fan. However, the high rotational speeds, blade vibration frequencies, and expected amplitudes pose challenges for the measurement setup. In this work, a high-speed DIC system is prepared and tested to measure deformation and vibration of a fast rotating blade. Additionally, the requirements for the DIC setup are defined and presented. The expected blade tip speeds in the CA3ViAR project are up to 295 m/s and the blade frequencies of interest up to 650 Hz. Therefore, particular emphasis must be given to the setup in order to eliminate motion blur due to the rotation and to achieve the required frequency. This leads to a setup with synchronised high-speed cameras and a laser to measure frequency vibrations up to 1 kHz with an exposure time below 210 ns. Test measurements are conducted on a stationary beam and an axial blower with a max. blade tip speed of 50 m/s. A data analysis method is developed and described to eliminate the rigid body rotation, analyse the deformation of each blade compared to a reference condition, and analyse the spatial vibration in the frequency domain for a high number of data points per time step. The results of the structural beam are in agreement with the reference measurements and numerical simulations. By analysing the spatial vibration modes of the axial blower, the 1F-flap mode is identified at 38 Hz. In conclusion, this DIC setup shows promising results for future deformation and vibration measurements on a scaled UHBR fan.

Long silence on the East Anatolian Fault Zone (Southern Turkey) ends with devastating double earthquakes (6 February 2023) over a seismic gap: implications for the seismic potential in the Eastern Mediterranean region

On 6 February 2023, an earthquake with magnitude M w c . 7.0 on the Narlı Fault, a fault sub-parallel to the East Anatolian Fault Zone (EAFZ), initiated a chain of large earthquakes on the EAFZ. The earthquakes occurred in a seismic gap with low geodetic strain rates and low background seismicity, where deformation is distributed across a wide fault zone and a long recurrence time of historical earthquakes. The c. 50 km long rupture of the Narlı Fault towards Pazarcık led to an M w 7.8 left-lateral strike-slip earthquake breaking a c. 300 km section of the c. 600 km long EAFZ bilaterally with a total duration of more than 80 s. Toward the SW, the rupture propagated on the c. 100 km long Amanos segment with a peak surface offset of 5 m, before diminishing toward the Hatay graben. In the NE direction, the rupture reached a peak surface offset of 7 m before sharply declining at the termination of the 2020 M w 6.8 Sivrice earthquake rupture. A second large earthquake with M w 7.6 occurred 9 h later on the Çardak Fault, located at the western margin of (and sub-parallel to) the EAFZ and breaking the surface with almost 9 m of left-lateral slip (average of c. 4 m). Following these large earthquakes, the increase in the regional stress led to a rapid seismic activation in a broad region from central to eastern Anatolia, loading the faults at various scales and increasing seismic hazard. Two weeks after the initiation of the seismic crisis, a third earthquake with M w 6.4 occurred at the southern boundary of the Hatay graben, near the southwestern termination of the Amanos rupture. The earthquakes caused significant loss of human life, devastating 12 cities. We evaluate the observations prior to the ruptures, and present preliminary seismological results with surface displacements from sub-pixel correlation of optical satellite images and the stress perturbations computed on the nearby faults based on preliminary slip models. The re-evaluation of the seismic potential in light of the recent and historical earthquakes provides some new insight on seismic hazard assessment. The recent series of events on the EAFZ is an important reminder that large faults can generate very large earthquakes on multiple segments. The seismic potential of large earthquakes on these fault zones can be estimated only by considering multiple seismic cycles and moment deficits from very large earthquakes. Supplementary material : Supplementary figures and tables are available at https://doi.org/10.6084/m9.figshare.c.6567094

Effects of a Preannealing Process on the Morphology of Developed Kinks in Mille-Feuille Structured Cu/A5052 Alloy Fabricated by Accumulative Roll Bonding: Criteria for Kink Formation

Cu/A5052 dissimilar metal laminates (DMLs) were fabricated by an accumulative roll bonding process. The Cu/A5052 DML consisted of hard and soft layers, in other words, high and low shear modulus layers, which is called a mille-feuille structure (MFS). The Cu/A5052 DML with the MFS showed kink deformation during monotonic compression. Kink formation was analyzed by in-situ optical microscopy and digital image correlation. The development behavior and morphology of the ortho-type kink depended on the annealing conditions prior to the compression tests. Based on the observations and measurements, criteria for kink formation in the DML with the MFS were proposed.