Open Network Structure Research Articles

A detailed study on the physical, mechanical, structural and gamma ray shielding properties of Al2O3–Na2O–SiO2–B2O3–Bi2O3glass system

The density, boron–boron separation, and molar volume of 4Al2O3–12Na2O-(18-x)SiO2-(64-x) B2O3-(2+2x)Bi2O3 (where x = 2, 4, 6 and 8 mol%) are increasing with the addition of Bi2O3. The addition of Bi2O3 results in an open network structure. The elastic moduli decrease from 34.711 to 29.875 GPa for Young modulus (E); 20.395 to 15.843 GPa for bulk modulus (B); from 15.257 to 13.494 GPa for shear modulus (G) and 40.738 to 33.836 GPa for longitudinal (L) respectively with increased Bi2O3 concentration. FTIR spectrainvestigation found BO3, BO4, SiO4, and BiO6 structural units to be present. The glasses' highest mass attenuation coefficient (MAC) is at 0.0395 MeV, the lowest energy value. It gradually decreases as energy increases. There is a decrease in the linear attenuation coefficient (LAC) values with energy. Sample Bi18 has the highest MAC and LAC values due to its high concentration of Bi2O3. Across the entire energy range, sample Bi18 has the highest effective atomic number, and the lowest half value layer and mean free path values across all energy values. The transmission factor (TF) values for Bi6 indicate that the required thickness for blocking 90% of the radiation must be greater than the thickness necessaryfor the attenuation of 50%. Bi18 has the lowest TF compared to other glass samples. The radiation protection efficiency values for Bi18 are highest, confirming their full protection ability. Bi18's is the best choice for radiation shielding.

Comparative analysis of classic network vs. nanogel junction network in konjac glucomannan/kappa carrageenan hybrid hydrogels

The three-dimensional network architecture of hydrogels significantly influences their mechanical and physical properties; therefore, understanding them is essential for designing optimized hydrogel-based biomaterials. This study presents a comparative analysis of two hybrid hydrogels composed of konjac glucomannan (KGM) and kappa carrageenan (KCAR) with the same stiffness (5.2–5.7 kPa and 1.6–1.7 kPa) thus similar cross-linking density but different network architectures: a classic network formed by extended polysaccharide interactions and a nanogel junction network where nanoscale cross-linked KCAR (KCAR-NGs) links KGM chains. The mechanical behavior, dissolution, and diffusion characteristics were examined, revealing that the classic network demonstrates superior tensile resistance, elongation, and solvent-induced swelling resistance, leading to slower dissolution rates and higher viscosity. Conversely, the nanogel junction network offers higher permeability for small molecules and faster dissolution, suggesting a more open network structure. These findings highlight the nanogel-based hydrogels' advantages for biomedical applications requiring stability, permeability, and rapid dissolution without high temperatures or chelating agents. This study underscores the potential of nanogel junction networks to balance hydrogel stiffness and permeability, advancing the design of hydrogel-based biomaterials.

Effect of extracorporeal shock wave therapy on the microbial community in burn scars: retrospective case-control study.

The effectiveness of extracorporeal shock wave therapy (ESWT) has been demonstrated in various medical fields, including burn medicine. It promotes wound healing, improves blood flow, and modulates the inflammatory responses. The recovery speed and outcomes of skin diseases are influenced by the skin microbiome; however, studies examining the effects of specific treatments on the skin microbiome are lacking. This study investigated the impact of ESWT on the skin microbiome of burn patients, focusing on the microbial diversity and community structure within burn scars. In the retrospective case-control study, nineteen patients with burn scars were treated with ESWT, and changes in their skin microbiome were evaluated. ESWT was administered weekly for three months, and samples were collected from the ESWT-treated burn scars and untreated normal skin. Blood chemistry, and pain and itching scores were evaluated during sample collection. The collected samples were then subjected to 16S rRNA sequencing. Microbial community analysis was conducted using the QIIME2 and R packages. After ESWT, changes in alpha diversity indices were observed in burn scars. Faith phylogenetic diversity (P<0.05) and observed features (P<0.01) increased, whereas the evenness index decreased (P<0.01); no marked changes were noted in untreated skin. Beta diversity analysis showed stable microbial community structures in both the treated and untreated areas. A considerable increase in Micrococcus and Staphylococcus abundance was observed. Network analysis revealed a more open microbial network structure after ESWT, indicating adaptive changes in the microbial community. ESWT enhances microbial diversity and modifies microbial community structure in burn scars, promoting a more balanced and functionally supportive microbiome. ESWT aids in scar remodeling and positively influences skin microbiome dynamics, contributing to improved skin health and recovery.

Effect of inorganic salt impurities on seeded precipitation of silica hydrate from sodium silicate solution

To clarify the precipitation of silica hydrate from the real desilication solutions of aluminosilicate solid wastes by adding seeds and improve integrated waste utilization, the seeded precipitation was studied using synthesized sodium silicate solution containing different inorganic salt impurities. The results show that sodium chloride, sodium sulfate, sodium carbonate, or calcium chloride can change the siloxy group structure. The number of high-polymeric siloxy groups decreases with increasing sodium chloride or sodium sulfate concentration, which is detrimental to seeded precipitation. Calcium chloride favors the polymerization of silicate ions, and even the chain groups precipitate with the precipitation of high-polymeric sheet and cage-like siloxy groups. The introduced sodium cations in sodium carbonate render a more open network structure of high-polymeric siloxy groups, although the carbonate ions favor the polymerization of siloxy groups. No matter how the four impurities affect the siloxy group structure, the precipitates are always amorphous opal-A silica hydrate.

Enhanced elastic stability of a topologically disordered crystalline metal–organic framework

By virtue of their open network structures and low densities, metal–organic frameworks (MOFs) are soft materials that exhibit elastic instabilities at low applied stresses. The conventional strategy for improving elastic stability is to increase the connectivity of the underlying MOF network, which necessarily increases the material density and reduces the porosity. Here we demonstrate an alternative paradigm, whereby elastic stability is enhanced in a MOF with an aperiodic network topology. We use a combination of variable-pressure single-crystal X-ray diffraction measurements and coarse-grained lattice-dynamical calculations to interrogate the high-pressure behaviour of the topologically aperiodic system TRUMOF-1, which we compare against that of its ordered congener MOF-5. We show that the topology of the former quenches the elastic instability responsible for pressure-induced framework collapse in the latter, much as irregularity in the shapes and sizes of stones acts to prevent cooperative mechanical failure in drystone walls. Our results establish aperiodicity as a counter-intuitive design motif in engineering the mechanical properties of framework structures that is relevant to MOFs and larger-scale architectures alike.

Ru nanocrystals modified porous FeOOH nanostructures with open 3D interconnected architecture supported on NiFe foam as high‐performance electrocatalyst for oxygen evolution reaction and electrocatalytic urea oxidation

The construction of binder-free electrodes with well-defined three-dimensional (3D) morphology and optimized electronic structure represents an efficient strategy for the design of high-performance electrocatalysts for the development of efficient green hydrogen technologies. Herein, Ru nanocrystals were modified on 3D interconnected porous FeOOH nanostructures with open network-like frameworks on NiFe foam (Ru/FeOOH@NFF), which were used as an efficient electrocatalyst. In this study, a 3D interconnected porous FeOOH with an open network structure was first electrodeposited on NiFe foam and served as the support for the in-situ modification of Ru nanocrystals. Subsequently, the Ru nanocrystals and abundant oxygen vacancies were simultaneously incorporated into the FeOOH matrix via the adsorption-reduction method, which involved NaBH4 reduction. The Ru/FeOOH@NFF electrocatalyst shows a large specific surface area, abundant oxygen vacancies, and modulated electronic structure, which collectively result in a significant enhancement of catalytic properties with respect to the oxygen evolution reaction (OER) and urea oxidation reaction (UOR). The Ru/FeOOH@NFF catalyst exhibits an outstanding OER performance, requiring a low overpotential (360 mV) at 200 mA cm−2 with a small Tafel slope (58 mV dec-1). Meanwhile, the Ru/FeOOH@NFF catalyst demonstrates more efficient UOR activity for achieving 200 mA cm−2 at a lower overpotential of 272 mV. Furthermore, an overall urea electrolysis cell using the Ru/FeOOH@NFF as the anode and Pt as the cathode (Ru/FeOOH@NFF||Pt) reveals a cell voltage of 1.478 V at 10 mA cm−2 and a prominent durability (120 h at 50 mA cm−2). This work will provide a valuable understanding of the construction of high-performance electrocatalysts with 3D microstructure for promoting urea-assisted water electrolysis.

The dual active sites reconstruction on gelatin in-situ derived 3D porous N-doped carbon for efficient and stable overall water splitting

The exploration of bifunctional electrocatalysts with high activity, stability, and economy is of great significance in promoting the development of water splitting. Herein, a dual active sites heterostructure NiCoS/NC was designed to be derived in situ on 3D N-doped porous carbon (NC) using gelatin as a nitrogen and carbon source. The characterization of experiments suggests that nanoflower-like Ni2CoS4 (abbreviated as NiCoS) was randomly distributed on the NC substrate, and the sheet-like NC formed a highly open porous network structure resembling a honeycomb, which provided more accessible active sites for electrolyte ions. In addition, the special nanostructures of the catalyst materials help to promote the surface reconstruction to the real active substance NiOOH/CoOOH, and the double active sites synergistically reduce the overpotential of OER and improve its kinetics. DFT (Density-functional theory) calculations reveal the electronic coupling of NiCoS/NC in atomic orbitals, modulation of electrons by the heterointerface and N-doping, and synergistic effect of dual active sites improving the inherent catalytic activity. The NiCoS/NC composite electrocatalyst exhibited a 177 mV small OER overpotential and a 132 mV small HER overpotential with Faraday efficiencies as high as 96 % and 98 % at 10 mA cm−2 current density. In the two-electrode system, it also requires only an ultra-low voltage of 1.52 V to achieve a 10 mA cm−2 current density, and it shows excellent long-term water splitting stability. This provides a new idea for the development of transition metal-based bifunctional electrocatalysts.

B2O3-Sb2O3-LiF glass anode with long-cycle stability

Glass anodes have received much concern due to their open network structure and ability to provide permeation channels for lithium-ions. However, there is still relatively little exploration of the electrochemical performance of F-ions-regulated glass network structure. In this work, fluoroborate glass with a loose network structure was prepared by the conventional melt-quenching method. This glass anodes (LF) induced the formation of Sb3+Sb5+O4 crystals through charge/discharge cycling, and the presence of the crystals enhanced the specific surface area and embedded lithium sites. After 900 cycles, the specific discharge capacity of the LF glass anode is maintained at 371.4 mAh g−1, and the introduction of F-ions effectively improves the cycling stability and cycle life of the anode in the B2O3-Sb2O3 glass system. This advances a new idea for the future research and development of glass anodes.

A novel strategy to construct hydrogels with anti-swelling and water-retention abilities by covalent surface modification.

Hydrogels have been widely used in various fields due to their diverse properties and flexible preparation methods. However, limited by the open network structure, hydrogels inevitably lose water in air or absorb water in aqueous solution, resulting in the loss of intrinsic functions, which severely hinders their practical applications. To address this issue, a general strategy was developed by subsequently modifying the surface of hydrogels with branched polyethyleneimine (PEI) and (3-(methacryloxy)propyl)trimethoxysilane (MPS) to covalently construct a dense cross-linked siloxane layer on the hydrogel surface. As a proof of concept, poly(2-(dimethylamino)ethyl methacrylate)/sodium alginate (PDMAEMA/SA) hydrogels were chosen as the model hydrogels to verify the feasibility of this strategy. The hydrogels adsorbed PEI to form amino-rich surfaces through hydrogen bonding, followed by covalently grafting MPS through rapid and catalyst-free mutual chemical reactions between acrylates and amine groups, as well as the hydrolysis of MPS. After modification, robust hydrophobic surfaces were successfully fabricated on the hydrophilic hydrogels. The modified hydrogels exhibited extraordinary anti-swelling and water-retention abilities. As the most typical intrinsic properties of hydrogels, the conductivity and sensing performance were well preserved. The strategy reported here provides a new insight into the construction of hydrogels with anti-swelling and water-retention abilities.

Time-dependent clay gels: Stepdown shear rate behavior, microstructure, ageing, and phase state ambiguity

To study the time-dependent properties of clay gels in the structural rejuvenation mode, a combination of the stepdown shear rate method and an ageing test is advocated. In this mode, the structural development process at two different initial equilibrium states during the low stepdown shear rate and the rest period of the ageing test were followed. The roles played by the electric double layer (EDL) repulsive force in this structural development process with and without shear, for platelet sodium montmorillonite or NaMnt, hectorite and Laponite gels, and fibrous sepiolite gels were assessed. The response of the stepdown shear stress and ageing yield stress reflects the action of these forces on the structural rejuvenation kinetics and the type of structure formed. The platelet clay gels with their strong EDL repulsive particle interaction commenced the structural development process immediately and formed an open network structure. This process is short in shear and takes years when without. The fibrous sepiolite gel with its weak EDL repulsive interaction did not display structural rejuvenation in shear and only showed a significant yield stress increase after the first few hours of ageing. An additional issue concerning the stability of the isotropic liquid (IL) phase state of dilute Laponite dispersions was addressed. These dispersions aged for &amp;gt;9 years, displaying that yield stress and network structure confirmed that the IL phase is unstable. A low energy path available for Laponite particles to aggregate was discussed. A new method for determining the flocculate phase state was also presented.

Inverse task of pollution spreading – Localization of source in extensive open channel network structure

Abstract This paper is focused on the problem of the pollutant source localisation in streams in other words the solution of the inverse problem of pollution spreading with in an extensive open channel network structure, i.e. in a complex system of rivers, channels and creeks in natural catchments or sewer systems in urban catchments. The design of the overall localisation procedure is based on the requirement that the entire localization system be operative and fast enough to enable quick operative interventions and help prevent the spread of pollution. The proposed model, as well as, the overall localisation procedure was calibrated and tested on a real sewer system, which represents in this case an extensive open channel network structure with free surface flow. The test results are successful and confirmed applicability of proposed localization tool in simple real conditions. However, the localisation procedure has pros and cons, which are discussed in the paper.

The role of lipids in determining the gas cell structure of gluten-free steamed oat cake

The stabilization of gas cells is crucial to obtain cake or bread products with a homogeneous crumb and is mainly depends on the proteins, starches, and lipids. Oats, in particular, are known for their high lipid content compared to other grains. However, the specific contribution of oat lipids to the gas chamber structure in gluten-free steamed oat cake is still unclear. Hence, to elucidate the potential mechanism involved, this study aimed to investigate the steaming characteristics of oat dough, as well as the protein-starch network matrix (including protein aggregation and structural properties), and the air/water interfacial characteristics (including foaming and surface tension properties) of oat dough liquor subjected to different defatting treatments. Results showed that by moderately removing lipids from samples (particularly ROF-D3 with 2.91% lipid content), gas retention ability, cell area fraction, and specific volume of the steamed oat cake were enhanced, which were 93.30 mL/100 mL, 36.27%, and 2.72 mL/g, respectively. Weak protein aggregation and an ordered protein secondary structure corresponding to a more open and stable protein network structure were observed in the ROF-D3 sample caused by moderate lipid removal. In addition, moderate removal of lipids obviously increased the extraction yield of oat dough liquor, in which lipid was evidently the dominant component. Compared to the ROF-D1 sample, the enhanced quality of the ROF-D3 sample can be attributed to the strongest foam stability and the increased air-water interface surface tension.

Monolithic fiber/foam-structured catalysts: beyond honeycombs and micro-channels

ABSTRACT Heterogeneous catalysis plays a pivotal role in the current chemical and energy vectors production. Notably, to fully utilize the intrinsic activity and selectivity of a catalyst, the chemical reactor has to be designed and operated optimally to achieve enhanced heat/mass transfer, well-defined contact time of reactants, uniform flow pattern, and high permeability. Structured catalysts are a promising strategy to overcome the major drawbacks encountered in the traditional packed-bed reactor technology due to the improved hydrodynamics in combination with enhanced heat/mass transfer. Newly emerged fiber/foam-substrates, with an entirely open 3D network structure, bring distinct advantages over the honeycomb and micro-channel contacting methods, including free radial diffusion, eddy-mixing driven heat/mass transfer, large area-to-volume ratio, and high contacting efficiency. However, how to place the nanocatalysts onto the fiber/foam-substrates is a challenging problem because the commercial washcoating method has great limitations such as the nonuniformity and easy exfoliation of coatings. This review discusses the newly developed non-dip-coating methods for the fiber/foam-structured catalysts and their promising applications in the strongly exo-/endo-thermic and/or high throughput reaction processes.

Efficient optimization of the Li-ion conductivity of borovanadate glass materials for Li-ion batteries

The lithium-doped borovanadate glasses of high chemical purity are obtained via the traditional-melt quenching method. The obtained glasses are identified as having an amorphous character by XRD. DSC spectra reveal the glassy nature and good thermal stability of the prepared samples. FTIR spectroscopy reveals the structural groups of these glasses. The incorporation of Li+ ions into the glass modifies the boron coordination so that the boron coordination number changes from BO4 to BO3. The structural conversion of BO4 to BO3 boosts the number of NBOs. The increased number of NBOs indicates borate network depolymerization and a more open network structure, which leads to Li+ ions easily transferring in the glass network. This, in turn, optimizes the ionic conductivity of the present glassy system and can be of order 10−4 S.cm−1 at 300 K. This is the highest value of ionic conductivity reached by the borovanadate glasses at 300 K. Accordingly, borovanadate glasses containing lithium could pave the way for the use of glass materials as electrode material for Li-ion batteries.

An effective copper doping strategy of Co(OH)F cathode for producing hydrogen in microbial electrolytic cells

In this study, the effective Cu doping Co(OH)F catalyst with three-dimensional network nanowires is successfully prepared by the one-step in situ hydrothermal route for Microbial Electrolytic Cell (MEC) cathode to improve the overall hydrogen production rate. The results demonstrate that the optimized doping ratio Cu-Co(OH)F exhibits a high open three-dimensional network structure and a good electrochemical hydrogen evolution activity (Tafel slope is 52.0 mV dec−1). In addition, the MEC with Cu-Co(OH)F cathode exhibits an extremely high current density of 69.2 A m−2, hydrogen production rate of 214.5 ml H2 L−1 cycle−1, and coulombic efficiency of 80.75%, which significantly improved the activity compared with undoped one. The results of density functional theory (DFT) calculations confirm that the doping of copper could regulate the electron transport rate and the Gibbs free energy to accelerate the process of hydrogen evolution, thus resulting in excellent hydrogen production in MEC.

Knowledge sharing and innovation in open networks of tourism businesses

PurposeThe purpose of this paper is to examine the information flows, in terms of content and process, underpinning the sharing of knowledge by managers and owners. Such an examination reveals similarities and differences that will influence the generation and dissemination of knowledge used in tourism business operations and contribute to innovation.Design/methodology/approachThis paper examines information flows within the theoretical and methodological framework of social network analysis. The findings were derived from a quantitative study of tourism managers and owners of a tourism hub in South-West England.FindingsThe main finding was that network structure characteristics determine the flow of information within owners’ and managers’ social networks. The owners of smaller businesses received information from several sources and, therefore, had fewer structural constraints and reported larger structural holes. In comparison, the managers had more brokerage opportunities to disseminate the information within their social networks.Research limitations/implicationsThis paper highlights knowledge sharing between tourism business managers and owners in an open network structure. First, an open network structure builds innovation through the provision of nonredundant information. This is determined through the effective size of structural holes and the dissemination of information through brokerage roles. Second, the knowledge capability of a destination is built up through the social networking of managers and owners. The generation and dissemination of knowledge in a tourism destination are facilitated by the social networking activities of managers and owners.Practical implicationsManagers and owners of tourism businesses require knowledge through information to assist with innovative business practices. The practical implication of this is that the social networks of managers and owners have different network characteristics, and that these differences result in consequences for the innovation of business practices. Another practical implication relates to the importance of managers in knowledge dissemination based on having several brokerage roles in the tourism destination.Originality/valueThese findings are important because an understanding of social networks and the flow of information is one of the keys to determining the influences on knowledge sharing within tourism destination knowledge networks of owners or managers and their potential contributions to innovation.

Core-Shell Hierarchical Fe/Cu Bimetallic Fenton Catalyst with Improved Adsorption and Catalytic Performance for Congo Red Degradation

The preparation of heterogeneous Fenton catalysts with both adsorption and catalytic properties has become an effective strategy for the treatment of refractory organic wastewater. In this work, 4A-Fe@Cu bimetallic Fenton catalysts with a three-dimensional core-shell structure were prepared by a simple, template-free, and surfactant-free methodology and used in the adsorption and degradation of Congo red (CR). The results showed that the open three-dimensional network structure and the positive charge of the surface of the 4A-Fe@Cu catalyst could endow a high adsorption capacity for CR, reaching 432.9 mg/g. The good adsorption property of 4A-Fe@Cu for CR not only did not inactivate the catalytic site on 4A-Fe@Cu but also could promote the contact between CR and the active sites on the catalyst surface and accelerate the degradation process. The 4A-Fe@Cu bimetallic catalyst exhibited higher catalytic activity than monometallic 4A@Cu and/or 4A-Fe catalysts due to low work function value. The effects of different pH, H2O2 dosages, and catalyst dosages on the catalytic performance of 4A-Fe@Cu were explored. In the conditions of 7.2 mM H2O2, 2 g/L 4A-Fe@Cu, and 1 g/L CR solution, the degradation ratio of CR by 4A-Fe@Cu could reach 99.2% at pH 8. This strategy provided guidance to the design of high-performance Fenton-like catalysts with both adsorption and catalysis properties for dye wastewater treatment.

Dewatering properties of pulps made from different parts of a Norway spruce (Picea abies)

Abstract A single Norway spruce tree (Picea abies) was manually fractionated into heartwood, sapwood, juvenile wood and branches. These fractions were chemically pulped, individually, in laboratory scale. The pulps were characterized and investigated in relation to dewatering behavior and sheet strength properties. An unbleached and unbeaten commercial kraft pulp from softwood fibers was used as a reference, and the fractionated pulps were within the same range in all tested properties. The fractionated pulps were then compared with each other, and fiber characteristics were used to explain differences in dewatering and strength. Heartwood pulp results in stronger and stiffer papers that are harder to dewater. Sapwood pulp gives more open network structures resulting in easy dewatering and high air permeance, although with lower strength properties compared to heartwood. Pulp from Juvenile wood gives s quite strong but brittle sheets, with efficient dewatering. Pulp from branches gives paper sheets with efficient dewatering, air permeance and relatively high elongation of break but lower strength. The results show that there is definitely potential for utilizing more parts of the trees for pulp and paper making, especially when tailoring the raw material origins after preferred paper properties.

Educational Migration Bridge: From Metaphor to Project

The purpose of the article is to analyze the topical problem of educational migration and ways to solve it. The article identifies factors preventing from successful adaptation and socialization of foreign students in recipient country as legal, pedagogical, psychological, lingvo-communicative are identified. Minimization of negative factors actualized the integrated strategy of educational migration «bridge construction» development aimed at solving tasks of migrants’ integration in Russian labour market, providing them with all-round support in getting education, improving professional qualification, adaptation and socialization. The term «bridge» is metaphorically used as an artificial, virtual «construction» functioning as a means for educational migration support of citizens.The experience of the Orenburg State University in development and realization of the longterm integrated strategy of educational migration «bridge construction» presented within the Strategic Academic Leadership Program «Priority 2030» is studied. Regarding the potential of the University and Orenburg region the ways of educational migration «bridge construction» are determined: introduction of educational migration interactions into mission and policy of the university; development of open university migration interactions network structures; implementation of educational migration interaction based on norms, values and ideals of person’s lingvo-communicative culture. The practical steps for the strategy realization within the project «Educational migration bridge» are described: formation of the united scientific, educational and cultural environment based on mutual activity in international scientific and educational community; arrangement of universities regional consortium for informing applicants from Asian countries, for training and living in universities campuses; establishment of the Faculty of foreign students’ education and digital educational platform ensuring logistics and student educational improvement management; development and realization of module network programs for foreign students; realization of additional educational programs in OSU Linguistic center. The authors analyze the main indicators of the project effectiveness: quantitative and qualitative results of the Faculty of foreign students’ education activity in training Russian and culture; establishment of the Orenburg branch of Foreign Students Association, students’ involvement in various interaction forms and special career guidance events; scientific and methodological support for teachers. Realization of the strategy implies creation in OSU in the nearest future a specific environment including social infrastructure for foreigners.

Mission accomplished? – 6 Years of InData - International open Database Network Structure for Sustainable Construction

InData (International open data network for sustainable construction) started in 2015 as a voluntary initiative with the goal to establish an International open Database Network Structure for construction products based on EPD (environmental product declaration) information. In 2022 InData can proof its results by its release of the InData network with international participating databases. A key precondition was offering and giving support for producing machine readable EPD/LCA (life cycle assessment) data in a harmonized data format. All participants of the InData Network have comitted to the format, including compliance rules. Beyond that, the works of InData have international significant relevance, as InData could implement its works in Standardization. And also, further key stakeholders have adopted the concept of an open database network structure. In this paper, the goals, results, and their relevance, as possible future key issues are presented.