On-line Comprehensive Two-dimensional Liquid Chromatography Research Articles

Comprehensive Two-Dimensional Liquid Chromatography-High-Resolution Mass Spectrometry for Complex Protein Digest Analysis Using Parallel Gradients.

Despite the high gain in peak capacity, online comprehensive two-dimensional liquid chromatography coupled with high-resolution mass spectrometry (LC × LC-HRMS) has not yet been widely applied to the analysis of complex protein digests. One reason is the method's reduced sensitivity which can be linked to the high flow rates of the second separation dimension (2D). This results in higher dilution factors and the need for flow splitters to couple to ESI-MS. This study reports proof-of-principle results of the development of an RPLC × RPLC-HRMS method using parallel gradients (2D flow rate of 0.7 mL min-1) and its comparison to shifted gradient methods (2D of 1.4 mL min-1) for the analysis of complex digests using HRMS (QExactive-Plus MS). Shifted and parallel gradients resulted in high surface coverage (SC) and effective peak capacity (SC of 0.6226 and 0.7439 and effective peak capacity of 779 and 757 in 60 min). When applied to a cell line digest sample, parallel gradients allowed higher sensitivity (e.g., average MS intensity increased by a factor of 3), allowing for a higher number of identifications (e.g., about 2600 vs 3900 peptides). In addition, reducing the modulation time to 10 s significantly increased the number of MS/MS events that could be performed. When compared to a 1D-RPLC method, parallel RPLC × RPLC-HRMS methods offered a higher separation performance (FHWH from 0.12 to 0.018 min) with limited sensitivity losses resulting in an increase of analyte identifications (e.g., about 6000 vs 7000 peptides and 1500 vs 1990 proteins).

Impact of conditioning runs on hydrophilic interaction chromatography repeatability and its application as a second dimension in online comprehensive two-dimensional liquid chromatography.

A common separation approach for polar compounds involves coupling reversed-phase liquid chromatography (RPLC) with hydrophilic interaction chromatography (HILIC) in two-dimensional chromatography. The higher proportion of acetonitrile used in the HILIC mobile phase, which enhances mass spectrometry detection, encourages its use in the second dimension. Previous studies demonstrated that the HILIC column can be partially equilibrated within very short timeframes without compromising retention time stability, rendering it suitable in online comprehensive two-dimensional liquid chromatography (LC×LC) setups. In addition, a specific number of conditioning cycles seems necessary to establish stable retention times. Here, the repeatability of HILIC when employed as second dimension in LC×LC was investigated, with a focus on determining the required number of conditioning cycles to achieve repeatable retention times. Various parameters influenced by the LC×LC online modulation system were studied, such as steep gradient slopes up to 8%, and very short equilibration times, less than or equal to dead time, as well as injection volume and solvent, which depend on the first dimension. Finally, the use of HILIC as a second dimension with tailored conditioning runs was applied to the analysis of hyaluronic acid hydrogel digests. The application of an RPLC×HILIC method using five conditioning runs yielded exceptional stability in second-dimension retention times.

Improving the Accuracy of Predictive 2D-LC Optimization Strategies: Incorporation of Simulated Elution Profiles to Account for Injection Band Broadening in Online Comprehensive Two-Dimensional Liquid Chromatography.

Method development in online comprehensive two-dimensional liquid chromatography (LC × LC) requires the selection of a large number of experimental parameters. The complexity of this process has led to several computer-based LC × LC optimization algorithms being developed to facilitate LC × LC method development. One particularly relevant challenge for predictive optimization software is to accurately model the effect of second dimension (2D) injection band broadening under sample solvent mismatch and/or sample volume overload conditions. We report a novel methodology that combines a chromatographic numerical simulation model capable of predicting elution profiles of analytes under conditions where peak distortion occurs with a predictive multiparameter Pareto optimization approach for online LC × LC. Preliminary method optimization is performed using a theoretical model to predict 2D injection profiles, and optimal experimental configurations obtained from the Pareto fronts are then subjected to further optimization using the simulation model. This approach drastically reduces the number of simulations and therefore the computational demand. We show that the optimal experimental conditions obtained in this manner are similar to those obtained using a complete optimization using only the simulation model. Online HILIC × RP-LC separation of phenolic compounds was used to compare experimental data to simulated two- and three-dimensional contour plots. The main advantage of the proposed approach is the ability to predict the formation of split or deformed peaks in the 2D, a significant benefit in online LC × LC method optimization, especially for separation combinations with mismatched mobile phases. A further benefit is that simulated elution profiles can be used for the visualization of predicted two-dimensional chromatograms for method selection.

In-silico method development and optimization of on-line comprehensive two-dimensional liquid chromatography via a shortcut model

Comprehensive two-dimensional liquid chromatography (LCxLC) represents a valuable alternative to conventional single column, or one-dimensional, liquid chromatography (1D-LC) for resolving multiple components in a complex mixture in a short time. However, developing LCxLC methods with trial-and-error experiments is challenging and time-consuming, which is why the technique is not dominant despite its significant potential. This work presents a novel shortcut model to in-silico predicting retention time and peak width within an RPLCxRPLC separation system (i.e., LCxLC systems that use reversed-phase columns (RPLC) in both separation dimensions). Our computationally effective model uses the hydrophobic-subtraction model (HSM) to predict retention and considers limitations due to the sample volume, undersampling and the maximum pressure drop. The shortcut model is used in a two-step strategy for sample-dependent optimization of RPLCxRPLC separation systems. In the first step, the Kendall's correlation coefficient of all possible combinations of available columns is evaluated, and the best column pair is selected accordingly. In the second step, the optimal values of design variables, flow rate, pH and sample loop volume, are obtained via multi-objective stochastic optimization. The strategy is applied to method development for the separation of 8, 12 and 16 component mixtures. It is shown that the proposed strategy provides an easy way to accelerate method development for full-comprehensive 2D-LC systems as it does not require any experimental campaign and an entire optimization run can take less than two minutes.

Theoretical and practical guidelines for solvent dilution between the two dimensions in online comprehensive two-dimensional liquid chromatography

Online comprehensive two-dimensional liquid chromatography (online LC x LC) has become increasingly popular. Among the different chromatographic modes that can be combined, hydrophilic interaction chromatography (HILIC) and reversed-phase liquid chromatography (RPLC) are particularly interesting because they offer a high degree of orthogonality. However, this combination remains complex due to the incompatibility of the solvents in the two dimensions. To avoid this problem, it is possible to dilute the first dimension (1D) effluent with (zdilution -1) volumes of a weaker solvent added to one volume of 1D-effluent, where zdilution represents the extent to which the fraction volume has been multiplied. This can be done using either active solvent modulation technology or an additional pump, prior to the second dimension analysis.The objective of this study was to develop theoretical models to predict whether or not dilution can be effective, and, if so, what is the minimum zdilution value required. This approach is based on the calculation of the ratio (called xdilution) between the peak standard deviation due to the injection process and the peak standard deviation in the absence of extra-column dispersion. xdilution was calculated from theoretical relationships and plotted as a function of zdilution, to predict the value required to obtain good peak shapes for the compound of interest. The maximum xdilution value was found to be of the order of 1 for chromatographically acceptable peak shapes. The proposed theoretical approach was experimentally validated on a number of representative small molecules and peptides. Agreement between experimental results and theoretical models was very high, especially for small molecules. Finally, it is shown that this approach helps to predict the most appropriate set of conditions in HILIC x RPLC, depending on the compounds to be separated.

Three-dimensional characteristic chromatogram by online comprehensive two-dimensional liquid chromatography: Application to the identification and differentiation of ginseng from herbal medicines to various Chinese patent medicines

One bottleneck problem in the quality control of traditional Chinese medicine (TCM) is the accurate identification of easily confused herbal medicines from Chinese patent medicine (CPM). Ginseng products derived from the multiple parts (e.g., root/rhizome, leaf, and flower bud) of multiple Panax species (P. ginseng, P. quinquefolius, P. notoginseng, P. japonicus, and P. japonicus var. major) are globally popular; however, their authentication is very challenging. Using online comprehensive two-dimensional liquid chromatography (LC × LC), we propose the concept of a three-dimensional characteristic chromatogram (3D CC) by integrating enhanced LC × LC separation and a contour plot that visualizes the stereoscopic chromatographic peaks and examine its performance in authenticating various ginseng products. Targeted at the resolution of 17 ginsenoside markers, an online LC × LC/UV system with a 56 min analysis time was constructed: a CORTECS UPLC Shield RP 18 column running at 0.1 mL/min for the first-dimensional chromatography and a Poroshell SB-Aq column at 2.0 mL/min in shift gradient mode in the second dimension of separation. In particular, ginsenosides Rg1/Re and Rc/Ra1 were well resolved. According to the presence/absence of stereo peaks consistent with the main ginsenoside markers in the 3D CC and the depth of shade (depending on peak volume), it was feasible to use a single method to identify and distinguish among 12 different ginseng species as the drug materials and the use of ginseng simultaneously from 21 CPMs. Conclusively, a practical solution enabling the accurate identification of easily confused TCMs was provided, covering both the drug materials and the compound preparations.

Using multiple heart-cutting valves and stop-flow operation to enable variable second dimension gradient times in online comprehensive two-dimensional liquid chromatography

Online comprehensive two-dimensional liquid chromatography (LC×LC) is the preferred method currently for the separation of highly complex mixtures of non-volatile compounds. With fully automated commercial instrumentation and software making the method appealing to both researchers and industry, the demand for systems with improved separation capabilities for highly complex mixtures such as those found in natural products or proteomics has increased. In this study we report an approach that enables variable second dimension analysis times based on the use of multiple heart-cutting valves and stop-flow operation to circumvent the requirement for very fast second dimension (2D) analyses in online LC×LC. As application, the HILIC×RP-LC analysis of condensed tannins (proanthocyanidins) in cocoa, grape seed and quebracho extracts is used to demonstrate the performance on the proposed methodology. The method offers increased flexibility compared to conventional online LC×LC separations in that longer 2D gradients can be used to accommodate more complex portions of the chromatogram, while shorter 2D gradients can be used in sections containing fewer peaks, while largely maintaining the benefits of comprehensive separation. We present an evaluation of the performance of the variable gradient time stop-flow HILIC×RP-LC method compared to a comparable, conventional online HILIC×RP-LC system in terms of practical peak capacities using established 2D-LC theory. The improved separation of especially low-level intermediate molecular weight proanthocyanidin oligomers by the former method demonstrates the benefits of the developed approach.

Sense and nonsense of shifting gradients in on-line comprehensive reversed-phase LC × reversed-phase LC

In on-line comprehensive two-dimensional liquid chromatography (LC × LC), the combination of similar chromatographic modes such as reversed-phase liquid chromatography × reversed-phase liquid chromatography (RPLC × RPLC) usually leads to the partial occupation of the available separation space. A possible solution to circumvent this issue may be to dynamically adjust the gradient elution in the second dimension (2D) throughout the LC × LC analysis. This allows the gradient elution to be tailored to the elution conditions of each fraction instead of using a conventional full gradient program in which the same gradient profile is repeated for each 2D-fraction. In this study, an online RPLC × RPLC method is optimized with shifting gradients in 2D. The logic behind implementing such programs in on-line LC × LC is explained. The optimized method consists of a combination of segmented and shifted gradient modes. It is shown that the retention space coverage can be increased by 50 % compared to a conventional full gradient program, leading to a significant increase in peak capacity (about 35 %). However, such an increase comes at the expense of larger peak widths in 2D and thus lower peak intensities. It is shown here that the use of shifting gradients raises another serious issue related to the repeatability of retention times between two successive 2D-separations.

Development of a sub-hour on-line comprehensive cation exchange chromatography x RPLC method hyphenated to HRMS for the characterization of lysine-linked antibody-drug conjugates.

This study details the development of on-line two-dimensional liquid chromatography (2D-LC) methods combining cation-exchange chromatography (CEX) and reversed-phase liquid chromatography (RPLC) for the separation of the charge variants of a lysine-linked antibody-drug conjugate (ADC). This combination gives an excellent example of the potential benefits of 2D-LC approaches for the analysis of such complex protein formats. CEX is considered the reference technique for the separation of protein charge variants but its retention mechanism usually requires the use of a high concentration of non-volatile salts, which impedes its compatibility with MS detection. In this context, the use of an on-line 2D-LC-MS approach not only allows on-line desalting and indirect coupling of CEX with mass spectrometry (MS) detection but it also provides increased and complementary information within a single analysis. The first part of this study was devoted to the choice of stationary phases and the optimization of chromatographic conditions in both dimensions. Based on the results obtained in 1D-CEX with ultraviolet detection (UV) and 1D-RPLC with UV and high-resolution mass spectrometry (HRMS) detections, an on-line comprehensive two-dimensional liquid chromatography method combining CEX and RPLC was developed. The last part of this study was devoted to the identification of the separated species using HRMS detection and in the comparison of three ADC samples exposed to different durations of thermal stress.

On-line 2D-RPLC x RPLC – HRMS to assess wastewater treatment in a pharmaceutical plant

Pharmaceutical effluents are complex media containing hundreds of compounds including active ingredients, intermediate products and unknown impurities. Bringing an industrial wastewater treatment plant (WWTP) into compliance with European directives requires a thorough analysis of the effluent. In this study, we demonstrate how online comprehensive two-dimensional liquid chromatography (on-line LC × LC) hyphenated to high resolution mass spectrometry (HRMS) can be a powerful analytical methodology to monitoring the outlet water, by analysing the content of known molecules while characterizing unknown compounds. Reversed phase liquid chromatography (RPLC) was used in both dimensions, with a penta-fluoro-phenyl silica-based column at neutral pH in the first dimension (1D) and a C18 column at acidic pH in the second one (2D). The conditions were optimized for a total analysis time of 60 min. The variability of both retention times and peak areas was evaluated. The average standard deviation on retention times was found to be less than 0.1 s in 2D. The relative standard deviation on peak area was about 7% for run-to-run analysis. This analytical approach, applied to the pharmaceutical effluents before (inlet) and after (outlet) wastewater treatment permitted to detect 240 compounds. These included 27 priority pharmaceutical products, 8 of which were of very high priority and their concentrations could be compared to target values. The comparison of 2D-LC and 1D-LC approaches clearly highlights the power of on-line RPLC x RPLC technique, which allows both targeted quantitative analysis and non-targeted qualitative analysis of pharmaceutical effluents.

Strategies to circumvent the solvent strength mismatch problem in online comprehensive two-dimensional liquid chromatography.

On-line comprehensive two-dimensional liquid chromatography is a powerful technique for the separation of highly complex samples. Due to the addition of the second dimension of separation, impressive peak capacities can be obtained within a reasonable analysis time compared to one-dimensional liquid chromatography. In online comprehensive two-dimensional liquid chromatography, the separation power is maximized by selecting two separation dimensions as orthogonal as possible, which most often requires the combination of different mobile phases and stationary phases. The online transfer of a given solvent from the first dimension to the second dimension may cause severe injection effects in the second dimension, mostly due to solvent strength mismatch. Those injection effects may include peak broadening, peak distortion, peak splitting or breakthrough phenomenon. They are often found to reduce significantly the peak capacity and the peak intensity. To overcome such effects, arising specifically in online comprehensive two-dimensional liquid chromatography, different methods have been developed over the years. In this review, we focused on the most recently reported ones. A critical discussion, supported by a theoretical approach, gives an overview of their advantages and drawbacks.

Comprehensive two-dimensional temperature-responsive × reversed phase liquid chromatography for the analysis of wine phenolics

Phenolic compounds are an interesting class of natural products because of their proposed contribution to health benefits of foods and beverages and as a bio-source of organic (aromatic) building blocks. Phenolic extracts from natural products are often highly complex and contain compounds covering a broad range in molecular properties. While many 1D-LC and mass spectrometric approaches have been proposed for the analysis of phenolics, this complexity inevitably leads to challenging identification and purification. New insights into the composition of phenolic extracts can be obtained through online comprehensive two-dimensional liquid chromatography (LC × LC) coupled to photodiode array and mass spectrometric detection. However, several practical hurdles must be overcome to achieve high peak capacities and to obtain robust methods with this technique. In many LC × LC configurations, refocusing of analytes at the head of the 2D column is hindered by the high eluotropic strength of the solvent transferred from the 1D to the 2D, leading to peak breakthrough or broadening. LC × LC combinations whereby a purely aqueous mobile phase is used in the 1D and RPLC is used in the 2D are unaffected by these phenomena, leading to more robust methods. In this contribution, the combination of temperature-responsive liquid chromatography (TRLC) with RPLC is used for the first time for the analysis of phenolic extracts of natural origin to illustrate the potential of this alternative combination for natural product analyses. The possibilities of the combination are investigated through analysis of wine extracts by TRLC × RPLC-DAD and TRLC × RPLC-ESI-MS.

Online Nanoflow Two-Dimension Comprehensive Active Modulation Reversed Phase–Reversed Phase Liquid Chromatography High-Resolution Mass Spectrometry for Metaproteomics of Environmental and Microbiome Samples

Metaproteomics is a powerful analytical approach that can assess the functional capabilities deployed by microbial communities in both environmental and biomedical microbiome settings. Yet, the mass spectra resulting from these mixed biological communities are challenging to obtain due to the high number of low intensity peak features. The use of multiple dimensions of chromatographic separation prior to mass spectrometry analyses has been applied to proteomics previously but can require increased sampling handling and instrument time. Here, we demonstrate an automated online comprehensive active modulation two-dimensional liquid chromatography method for metaproteome sample analysis. A high pH PLRP-S column was used in the first dimension followed by low pH separation in the second dimension using dual modulating C18 traps and a C18 column. This method increased the number of unique peptides found in ocean metaproteome samples by more than 50% when compared to a one-dimension separation while using the same amount of sample and instrument time.

Comparison of Online Comprehensive HILIC × RP and RP × RP with Trapping Modulation Coupled to Mass Spectrometry for Microalgae Peptidomics

In this work, two online comprehensive two-dimensional liquid chromatography platforms, namely Hydrophilic interaction liquid chromatography × Reversed phase (HILIC × RP) and Reversed phase × Reversed Phase (RP × RP) coupled to mass spectrometry, were compared for the analysis of complex peptide samples. In the first dimension, a HILIC Amide and C18 Bioshell peptide (150 × 2.1 mm, 1.7 and 2.0 μm) columns were selected, while, in the second dimension, a short C18 (50 × 3.0 mm, 2.7 μm) Bioshell peptide column was used. Two C18 trapping columns (10 × 3.0 mm, 1.9 μm), characterized by high retention and surface area, were employed as modulation interface in both HILIC × RP and RP × RP methods. The LC × LC platforms were coupled to UV and tandem mass spectrometry detection and tested for the separation and identification of two gastro-intestinal digests of commercial microalgae formulations (Spirulina Platensis and Klamath). Their performances were evaluated in terms of peak capacity, maximum number and properties of identified phycocyanin peptides. Our results showed that the HILIC × RP approach provided the highest peak capacity values (nc HILIC × RP: 932 vs. nc RP × RP: 701) with an analysis time of 60 min, while the RP × RP approach was able to identify a slight higher number of phycocyanin derived peptides (HILIC × RP: 88 vs. RP × RP: 103). These results point out the flexibility and potential of HILIC × RP and RP × RP based on trapping modulation for peptide mapping approaches.

Two-Dimensional Liquid Chromatography Coupled to High-Resolution Mass Spectrometry for the Analysis of ADCs.

From a structural point of view, the complete characterization of ADCs is a challenging task due to their high complexity. ADCs combine the heterogeneity of the initial antibody to the variability associated with the conjugation strategy, the manufacturing process, and the storage. Given the inherent complexity of these biomolecules, online comprehensive two-dimensional liquid chromatography (LC×LC) is an attractive technique to address the challenges associated with ADC characterization. Compared to conventional one-dimensional liquid chromatography techniques (1D-LC), LC×LC combines two different and complementary separation systems. In the context of ADC analysis, LC×LC has been proven to be a rapid and efficient analytical tool: (1) to provide a higher resolving power by increasing the overall peak capacity and thus allowing to gain more information within a single run and (2) to allow mass spectrometry (MS) coupling with some chromatographic techniques that are not MS-compatible and hence to facilitate the structural elucidation of ADCs. In this chapter, we present the coupling of different chromatographic techniques including hydrophobic interaction chromatography (HIC), reversed phase liquid chromatography (RPLC), size exclusion chromatography (SEC), ion exchange chromatography (IEX), and hydrophilic liquid chromatography (HILIC). The interest of HIC×SEC, SEC×SEC, HIC×RPLC, IEX×RPLC, RPLC×RPLC, and HILIC×RPLC, all hyphenated to high-resolution mass spectrometry (HRMS), is discussed in the context of the characterization of ADCs.

Quantitative analysis of aqueous phases of bio-oils resulting from pyrolysis of different biomasses by two-dimensional comprehensive liquid chromatography

Agrifood by-products are perfect candidates to be further processed under the concept of circular economy, in order to produce their valorization. Although significant amounts of food-related wastes that are discarded are produced worldwide, these might still be rich in valuable compounds. A strategy to further valorize agrifood-related by-products is based on pyrolysis processes. The result of this process is a liquid product termed bio-oil which is composed of an organic phase and an aqueous phase. This bio-oil is rich on a variety of components and its analysis implies several challenges. In this work, quantitative on-line comprehensive two-dimensional liquid chromatography (LC × LC) is proposed for the first time to characterize several aqueous phases of different bio-oils. Rice husk, peanut shell, spent coffee grounds, peach core and Eucalyptus sawdust biomasses were analyzed. The developed quantitative LC × LC method presented very good linearity, precision, reproducibility, recovery and LODs and LOQs as low as 0.05 μg mL−1 and 0.16 μg mL−1, respectively. As much as 28 components were simultaneously separated and quantified in those samples. Our results found that the composition of these bio-oils was different but strongly related to the agrifood by-product submitted to pyrolysis. The developed methodology is foreseen as a valuable tool for the quantitative study of other bio-oils, considering the great complexity and high dimensionality of these samples.

Analysis of charged acrylic particles by on-line comprehensive two-dimensional liquid chromatography and automated data-processing

A thorough understanding of particle formation and polymer growth during emulsion polymerization is indispensable for the development of particles and products with very specific properties. This has created a demand for the detailed characterization of various properties and property distributions – and the relation between these. A method is described that enables comprehensive, simultaneous determination of the size distribution of nanoparticles and the molecular-weight distribution of the constituting polymers as a function of the particle size. The result is a complete two-dimensional distribution that details the interdependence of the two parameters. The approach comprehensively combines hydrodynamic chromatography with size-exclusion chromatography. An automated band-broadening filter has been developed to improve the accuracy of the measured distributions. The algorithm utilizes automated curve-fitting approaches to describe detected particle distributions for each horizontal slice of the 2D-LC chromatogram, and filters band broadening using calibration curves. The method has been applied to samples of complex nanoparticles comprising hydrophobic, hydrophilic and charged moieties, viz. stabilized dispersions of poly[(methyl methacrylate)-co-(butyl acrylate)-co-(methacrylic acid)]-nanoparticles in water. We consistently found that, within a single population of particles, the weight-average molecular weight increases with particle size.

Pulsed elution modulation for on-line comprehensive two-dimensional liquid chromatography coupling reversed phase liquid chromatography and hydrophilic interaction chromatography

In this work, a reversed phase liquid chromatography (RPLC) coupling to hydrophilic interaction chromatography (HILIC) system has been constructed, combining with pulsed elution reversed phase liquid chromatography (PE-RPLC) and HILIC to comprehensively analyze P. ginseng root extract, which is rich in saponins. By the application of pulsed elution (PE) modulation technique, the proposed RPLC × HILIC system allows the chromatographic separation to be optimized independently in both dimensions. In the first dimension (1D), PE modulation is achieved by the separation of a complex mixture, such as P. ginseng root extract, with a PE gradient. This PE gradient contains a set of pulses where the solvent strength increases gradually. Thus, the modulation of 1D eluent is realized by stepwise-pulse fractionation, rather than by a traditional two-dimensional interface. Furthermore, the number of fractions and the fractionated period can be regulated independently, which leads to independent adjustment of the separation cycle in the second dimension (2D) separation without the loss of D1 separation efficiency. To overcome the inherent solvent incompatibility of RPLC × HILIC, we introduced a newly developed trapping interface, equipped with bypass. The result indicates excellent separation of saponins in P. ginseng root extract. Compared with the traditional modulation method, the proposed RPLC × HILIC system has extreme flexibility, those modulation time could be regulated in a large range without re-optimizing the 1D PE gradient. Worthily mentioned, the proposed RPLC × HILIC system shows excellent orthogonality, and 20% more peaks could be obtained with current method compared to the traditional value based modulation method. Independent regulation of both dimensions could enable the proposed modulation method to be widely applied for complex samples analysis in ordinary laboratory.

Quantitative aspects in on-line comprehensive two-dimensional liquid chromatography for pharmaceutical applications

On-line comprehensive two-dimensional liquid chromatography (on-line LCxLC) is expected to offer impressive effective peak capacity. That makes it an attractive technique for the analysis of complex samples such as pharmaceuticals, for which impurities are often unknown both in number and in structure, and can be either totally different or similar to the active substance. A study on comprehensive on-line RPLCxRPLC (reversed phase liquid chromatography in both dimensions) with respect to quantitative aspect at low concentration levels was carried out with the objective of finding conditions able to meet regulatory requirements for the control of pharmaceutical impurities. Preliminary studies showed that the best approach for quantitative purpose was to relate the impurity concentration to the sum of the second dimension peak areas. RPLCxRPLC conditions were optimized according to a Pareto-optimality approach with a focus on sensitivity, thereby favouring low dilution factor. The resulting RPLCxRPLC separation led to a detection limit below 0.05% for impurities (compared with API). Furthermore, the properties of this analytical method was found to be satisfying in terms of linearity (R2 > 0.999), repeatability (RSD < 1% for second dimension retention times) and precision (RSD < 1.5% for the sum of second dimension peak areas). Finally, this on-line RPLCxRPLC approach was applied to the analysis of a batch of drug substance in the early stages of drug development. The method was able to detect impurities at concentrations as low as 0.04% (signal-to-noise ratio of 3). All these results clearly demonstrate the power of on-line RPLCxRPLC for the quantitative analysis of pharmaceutical samples.

A multidimensional analytical approach based on time-decoupled online comprehensive two-dimensional liquid chromatography coupled with ion mobility quadrupole time-of-flight mass spectrometry for the analysis of ginsenosides from white and red ginsengs

Here, time-decoupled comprehensive two-dimensional ultra-high liquid chromatography (UHPLC) coupled with an ion mobility (IM)-high resolution mass spectrometer (HRMS) was established and used to analyze ginsenosides from the main roots of white ginseng (WG) and red ginseng (RG), which enabled the separation of complex samples in four dimensions (2D-LC, ion mobility, and mass spectrometry). The incompatibility of mobile phases, dilution effect, and long analysis time, which are the main shortcomings of traditional comprehensive 2D-LC methods, were largely avoided in this newly established 2D-UHPLC method. The orthogonality of this system was 55%, and the peak capacity was 4392. Under the optimized 2D-UHPLC-IM-MS method, 201 ginsenosides were detected from white and red ginseng samples. Among them, 10 pairs of co-eluting isobaric ginseng saponins that were not resolved by 2D-UHPLC-HRMS were further resolved using 2D-UHPLC-IM-MS. In addition, 24 ginsenoside references were analyzed by UHPLC-IM-MS to obtain their collision cross section (CCS) values and ion mobility characteristics. Finally, the established new method combined with multivariate statistical analysis was successfully applied to differentiate WG and RG, and 9 ginsenosides were found to be the potential biomarkers by S-Plot and the values of max fold change, which could be used for classifying WG and RG samples. Overall, the obtained results demonstrate the applicability and potential of the established time-decoupled online comprehensive 2D-UHPLC-IM-MS system, and it will be extended to the analysis of other targeted or untargeted compounds, especially co-eluting isomers in more herbal extracts.