Polyethylene Terephthalate Oligomers Research Articles

Unveiling PET Hydrolase Surface Dynamics through Fluorescence Microscopy.

PET hydrolases are an emerging class of enzymes that are being heavily researched for their use in bioprocessing polyethylene terephthalate (PET). While work has been done in studying the binding of PET oligomers to the active site of these enzymes, the dynamics of PET hydrolases binding to a bulk PET surface is an unexplored area. Here, methods were developed for total internal reflection fluorescence (TIRF) microscopy and fluorescence recovery after photobleaching (FRAP) microscopy to study the adsorption and desorption dynamics of these proteins onto a PET surface. TIRF microscopy was employed to measure both on and off rates of two of the most commonly studied PET hydrolases, PHL7 and LCC, on a PET surface. It was found that these proteins have a much slower off rates on the order of 10-3 s-1 , comparable to non-productive binding in enzymes such as cellulose. In combination with FRAP microscopy, a dynamic model is proposed in which adsorption and desorption dominates over lateral diffusion over the surface. The results of this study could have implications for the future engineering of PET hydrolases, either to target them to a PET surface or to modulate interaction with their substrate.

Dynamics behavior of PE and PET oligomers in lipid bilayer simulations

In recent years many investigators have been concerned about the toxicity and potential health hazards of micro- and nanoplastics. However, we are still lacking a good understanding of the methods of their transport into the human body and subsequently within cells. This is especially true at the lower nanometer scale; these particles are potentially more dangerous than their micrometer counterparts due to their easier permeation into cells. In this study we used both unbiased molecular dynamics simulations and steered umbrella sampling simulations to explore the interactions of polyethylene terephthalate (PET) and polyethylene (PE) oligomers in phospholipid bilayers. Our simulations revealed that the bilayers did not represent significant energy barriers to the small oligomers; not only did they readily enter the cell membrane but they also became concentrated into specific parts of the membrane. The larger PET tetramers exhibited a strong aggregation in water but were the least likely to permeate through or into the membranes. It is possible that PE monomers and tetramers can become concentrated into membranes while PET monomers are more likely to pass through or concentrate just inside the membrane surface. Passive transport of microplastics into cells is, however, likely limited to particles of a few nanometers in diameter.

Determination of plastic polyester oligomers in real samples and their bioeffects.

Plastics are ubiquitously, becoming part of our everyday life. Recently, the issue of human exposure to micro- and nanoplastic particles and potentially resulting toxicological consequences has been broached, triggered by the discovery of microplastics in foodstuff and dietary exposure via contaminated food and beverages. Within this EU-FORA fellowship project, a determination and quantification of plastic polyester plastics oligomers in food samples was performed to assess exposure at these categories of 'nanoplastics', evaluating them as potential contaminants or as indicators and marker compounds of the exposure to specific nanoplastics/microplastics from polyesters, such as polyethylene terephthalate (PET) and polybutylene terephthalate (PBT). UHPLC-TOF-MS/MS analysis has been set-up for 10 PET and PBT oligomers and analysis has been performed in foods and drinks. Moreover, the project focused also on the effects of these oligomers in in vitro and ex vivo experiments. These data would be combined with EFSA Comprehensive Food Consumption Database, for the exposure and risk assessment of these 'Nanoplastics'.

Upcycling of PET oligomers from chemical recycling processes to PHA by microbial co-cultivation

Polyethylene terephthalate (PET) is the most widely consumed polyester plastic and can be recycled by many chemical processes, of which glycolysis is most cost-effective and commercially viable. However, PET glycolysis produces oligomers due to incomplete depolymerization, which are undesirable by-products and require proper disposal. In this study, the PET oligomers from chemical recycling processes were completely bio-depolymerized into monomers and then used for the biosynthesis of biodegradable plastics polyhydroxyalkanoates (PHA) by co-cultivation of two engineered microorganisms Escherichia coli BL21 (DE3)-LCCICCG and Pseudomonas putida KT2440-ΔRDt-ΔZP46C-M. E. coli BL21 (DE3)-LCCICCG was used to secrete the PET hydrolase LCCICCG into the medium to directly depolymerize PET oligomers. P. putida KT2440-ΔRDt-ΔZP46C-M that mastered the metabolism of aromatic compounds was engineered to accelerate the hydrolysis of intermediate products mono-2-(hydroxyethyl) terephthalate (MHET) by expressing IsMHETase, and biosynthesize PHA using ultimate products terephthalate and ethylene glycol depolymerized from the PET oligomers. The population ratios of the two microorganisms during the co-cultivation were characterized by fluorescent reporter system, and revealed the collaboration of the two microorganisms to bio-depolymerize and bioconversion of PET oligomers in a single process. This study provides a biological strategy for the upcycling of PET oligomers and promotes the plastic circular economy.

Analysis of Migrant Cyclic PET Oligomers in Olive Oil and Food Simulants Using UHPLC-qTOF-MS.

Oligomers are a particular category of non-intentionally added substances (NIAS) that may be present in food contact materials (FCMs), such as polyethylene terephthalate (PET), and consequently migrate into foods. Here, an ultra-high-pressure liquid chromatography quadruple time-of-flight mass spectrometry (UHPLC-qTOF-MS) method was developed for the analysis of 1st series cyclic PET oligomers in virgin olive oil (VOO) following a QuEChERS clean-up protocol. Oligomer migration was evaluated with two different migration experiments using bottles from virgin and recycled PET: one with VOO samples stored in household conditions for a year and one using the food simulant D2 (95% v/v ethanol in water) at 60 °C for 10 days. Calibration curves were constructed with fortified VOO samples, with the LOQs ranging from 10 to 50 µg L-1 and the recoveries ranging from 86.6 to 113.0%. Results showed no migration of PET oligomers in VOO. However, in the simulated study, significant amounts of all oligomers were detected, with the migration of cyclic PET trimers from recycled bottles being the most abundant. Additional substances were tentatively identified as linear derivatives of PET oligomers. Again, open trimer structures in recycled bottles gave the most significant signals.

Controlling PET oligomers vs monomers via microwave-induced heating and swelling

The production of polyethylene terephthalate (PET) bottles and fibers, and their subsequent mismanagement, have created an urgent need to develop strategies to handle the resulting waste. Here, glycolysis of PET using manganese oxide catalysts under microwave-assisted heating is demonstrated to form oligomers and the monomer bis(2-hydroxyethyl) terephthalate (BHET) at moderate conditions. Higher surface area catalysts achieve faster overall rates of depolymerization to the monomer. Oligomers form homogeneously and depolymerize to monomers over manganese oxide. The polymer-to-solvent ratio and reaction temperature affect the overall oligomer yield. The swelling of PET, caused by the diffusion of ethylene glycol into the polymer matrix, causes the dissolution of the PET to form oligomers. Oligomers are characterized and show similar physical properties to the starting PET despite having 1/20th of the molecular weight.

Evaluating the food safety and risk assessment evidence-base of polyethylene terephthalate oligomers: A systematic evidence map

BackgroundThe presence of polyethylene terephthalate (PET) oligomers in food contact materials (FCMs) is well-documented. Consumers are exposed through their migration into foods and beverages; however, there is no specific guidance for their safety evaluation. ObjectivesThis systematic evidence map (SEM) aims to identify and organize existing knowledge and associated gaps in hazard and exposure information on 34 PET oligomers to support regulatory decision-making. MethodsThe methodology for this SEM was recently registered. A systematic search in bibliographic and gray literature sources was conducted and studies evaluated for inclusion according to the Populations, Exposures, Comparators, Outcomes, and Study type (PECOS) framework. Inclusion criteria were designed to record hazard and exposure information for all 34 PET oligomers and coded into the following evidence streams: human, animal, organism (non-animal), ex vivo, in vitro, in silico, migration, hydrolysis, and absorption, distribution, metabolism, excretion/toxicokinetics/pharmacokinetics (ADME/TK/PK) studies. Relevant information was extracted from eligible studies and synthesized according to the protocol. ResultsLiterature searches yielded 7445 unique records, of which 96 were included. Data comprised migration (560 entries), ADME/TK/PK-related (253 entries), health/bioactivity (98 entries) and very few hydrolysis studies (7 entries). Cyclic oligomers were studied more frequently than linear PET oligomers. In vitro results indicated that hydrolysis of cyclic oligomers generated a mixture of linear oligomers, but not monomers, potentially allowing their absorption in the gastrointestinal tract. Cyclic dimers, linear trimers and the respective smaller oligomers exhibit physico-chemical properties making oral absorption more likely. Information on health/bioactivity effects of oligomers was almost non-existent, except for limited data on mutagenicity. ConclusionsThis SEM revealed substantial deficiencies in the available evidence on ADME/TK/PK, hydrolysis, and health/bioactivity effects of PET oligomers, currently preventing appropriate risk assessment. It is essential to develop more systematic and tiered approaches to address the identified research needs and assess the risks of PET oligomers.

Migration Modeling as a Valuable Tool for Exposure Assessment and Risk Characterization of Polyethylene Terephthalate Oligomers

Polyethylene terephthalate (PET) is one of the most widely used food contact materials due to its excellent mechanical properties and recyclability. Migration of substances from PET and assessment of compliance are usually determined by experimental testing, which can be challenging depending on the migrants of interest. Low concentrations and missing reference standards, among other factors, have led to inadequate investigation of the migration potential of PET oligomers. Migration modeling can overcome such limitations and is therefore a suitable starting point for exposure and risk assessment. In this study, the activation energy-based (EA) model and the AP model were used to systematically evaluate the migration potential of 52 PET oligomers for 12 different application scenarios. Modeling parameters and conditions were evaluated to investigate their impact and relevance on the assessment of realistic exposures. Obtained results were compared with safety thresholds known from the concept of toxicological thresholds of concern. This allowed the evaluation and identification of oligomers and/or applications where migration or exposure levels may be associated with a potential risk because they exceed these safety thresholds. Overall, this study demonstrated that migration modeling can be a high-throughput, fast, flexible, and suitable approach for comprehensive exposure assessment.

Evaluating the food safety and risk assessment evidence-base of polyethylene terephthalate oligomers: Protocol for a systematic evidence map.

Polyethylene terephthalate (PET) oligomers are ubiquitous in PET used in food contact applications. Consumer exposure by migration of PET oligomers into food and beverages is documented. However, no specific risk assessment framework or guidance for the safety evaluating of PET oligomers exist to date. The aim of this systematic evidence map (SEM) is to identify and organize existing knowledge clusters and associated gaps in hazard and exposure information of PET oligomers. Research needs will be identified as an input for chemical risk assessment, and to support future toxicity testing strategies of PET oligomers and regulatory decision-making. Multiple bibliographic databases (incl. Embase, Medline, Scopus, and Web of Science Core Collection), chemistry databases (SciFinder-n, Reaxys), and gray literature sources will be searched, and the search results will be supplemented by backward and forward citation tracking on eligible records. The search will be based on a single-concept PET oligomer-focused strategy to ensure sensitive and unbiased coverage of all evidence related to hazard and exposure in a data-poor environment. A scoping exercise conducted during planning identified 34 relevant PET oligomers. Eligible work of any study type must include primary research data on at least one relevant PET oligomer with regard to exposure, health, or toxicological outcomes. For indexed scientific literature, title and abstract screening will be performed by one reviewer. Selected studies will be screened in full-text by two independent reviewers. Gray literature will be screened by two independent reviewers for inclusion and exclusion. Risk of bias analysis will not be conducted as part of this SEM. Will be performed by one reviewer and peer-checked by a second reviewer for indexed scientific literature or by two independent reviewers for gray literature. The extracted and coded information will be synthesized in different formats, including narrative synthesis, tables, and heat maps. Zenodo: https://doi.org/10.5281/zenodo.6224302.

PE and PET oligomers\u2019 interplay with membrane bilayers

The prevalence of microplastic pollution in nature and foodstuffs is fairly well identified. However, studies of micro- or nanoplastics’ cell membrane permeation and health effects in humans are lacking. Our study focuses on examining the interactions of polyethylene (PE) and polyethylene terephthalate (PET) with bilayer membranes. We have performed molecular dynamics simulations to study how plastic oligomers behave in bilayers. In addition, we have studied membrane permeation of PE and Bis(2-hydroxyethyl) terephthalate (BHET), a type of PET monomer, with Parallel Artificial Membrane Permeability Assay (PAMPA). As a result, in simulations the molecules exhibited different movements and preferred locations in membrane. PAMPA studies suggested similar preferences in membrane, especially for PE plastic. Our results suggest that passive diffusion could be an important transport mechanism into cells for some small plastic oligomers. Both molecular dynamics simulations and PAMPA have potential for micro- and nanoplastics research.

Liquid chromatography-mass spectrometry method for the determination of polyethylene terephthalate and polybutylene terephthalate cyclic oligomers in blood samples.

Food contact materials (FCM) polyethylene terephthalate (PET) and polybutylene terephthalate (PBT) used extensively in food packaging may contain cyclic oligomers which may migrate into food and thus cause toxic effects on human health. A simple, fast, and sensitive ultra-high-performance liquid chromatography method quadrupole time-of-flight mass spectrometer was developed for the analysis of 7 cyclic oligomers in post-mortem blood samples. The targeted analytes were separated on a Waters BEH C18 (150 × 2.1mm, 1.7µm) analytical column by gradient elution. Calibration curves were constructed based on standard solutions and blood samples and Student's t-test was applied to evaluate the matrix effect. The LODs ranged from 1.7 to 16.7μgmL-1, while the method accuracy was assessed by recovery experiments and resulting within the range 84.2-114.6%. Such an analytical method for the determination of PET and PBT cyclic oligomers in biological samples is reported for the first time. The developed methodology allows the determination of these oligomers in blood providing a useful analytical tool to assess the exposure and thus the potential hazard and health risks associated with these non-intentionally added substances (NIAS) from PET and PBT FCM through food consumption. The method was validated and successfully applied to the analysis of 34 post-mortem whole blood samples. Polyethylene terephthalate trimer was detected in four of them, for the first time in literature.

Nontargeted Analysis of Face Masks: Comparison of Manual Curation to Automated GCxGC Processing Tools.

Masks constructed of a variety of materials are in widespread use due to the COVID-19 pandemic, and people are exposed to chemicals inherent in the masks through inhalation. This work aims to survey commonly available mask materials to provide an overview of potential exposure. A total of 19 mask materials were analyzed using a nontargeted analysis two-dimensional gas chromatography (GCxGC)-mass spectrometric (MS) workflow. Traditionally, there has been a lack of GCxGC-MS automated high-throughput screening methods, resulting in trade-offs with throughput and thoroughness. This work addresses the gap by introducing new machine learning software tools for high-throughput screening (Floodlight) and subsequent pattern analysis (Searchlight). A recursive workflow for chemical prioritization suitable for both manual curation and machine learning is introduced as a means of controlling the level of effort and equalizing sample loading while retaining key chemical signatures. Manual curation and machine learning were comparable with the mask materials clustering into three groups. The majority of the chemical signatures could be characterized by chemical class in seven categories: organophosphorus, long chain amides, polyethylene terephthalate oligomers, n-alkanes, olefins, branched alkanes and long-chain organic acids, alcohols, and aldehydes. The olefin, branched alkane, and organophosphorus components were primary contributors to clustering, with the other chemical classes having a significant degree of heterogeneity within the three clusters. Machine learning provided a means of rapidly extracting the key signatures of interest in agreement with the more traditional time-consuming and tedious manual curation process. Some identified signatures associated with plastics and flame retardants are potential toxins, warranting future study to understand the mask exposure route and potential health effects.

Linear and cyclic oligomers in PET, glycol-modified PET and Tritan™ used for food contact materials

ABSTRACT Polyesters are commonly used as food contact materials. During manufacture of polyesters different low molecular mass oligomers (<1000 Da) are formed in the polymer melt. These so-called non-intentionally added substances (NIAS) are potential migrants into foods. In this work, different polyester samples made of polyethylene terephthalate (PET), glycol-modified PET (PETG) and Tritan™ were investigated on their qualitative and quantitative oligomer composition. The analysis of acetonitrile extracts by HPLC-DAD/ESI-MS revealed the presence of about 100 linear (different combinations of hydroxyl-, carboxyl-, methyl ester end groups) and cyclic oligomers depending on the main and co-monomers. The identified oligomers were quantified in different extracts and after reprecipitation by HPLC-DAD using bis-hydroxyethylene terephthalate (BHET) as external standard. The amount of oligomers isolated by reprecipitation ranged between 0.80 and 3.4% in the respective polyester. Cyclic oligomers generally made up 90% or more of the isolated oligomers. Compared to the exhaustive extracts the leaching of oligomers into 20% ethanol (1 h, 60 °C) resulted in a considerable change of the oligomer distribution with a predominant detection of linear oligomers. This suggests linear oligomers to be relevant for migration into aqueous foods despite the dominant amount of extractable cyclic oligomers in polyesters. Analysis of the extractable oligomers of a PET preform and a PETG container and their corresponding raw material pellets revealed that the injection moulding process did not significantly change the amount of cyclic oligomers but did increase the amount of low molecular mass linear oligomers about twofold.

Proficiency test on the determination of polyethylene and polybutylene terephthalate cyclic oligomers in a food simulant.

The outcome of a proficiency test (PT) organised by the European Union Reference Laboratory for Food Contact Materials (EURL-FCM) is presented. The PT was set up to assess the analytical performance of National Reference Laboratories (NRLs) and Official Control Laboratories (OCLs) in the determination of mass fractions of polyethylene terephthalate (PET) and polybutylene terephthalate (PBT) cyclic dimers and trimers in the official food simulant D1 containing ethanol and water (50:50 v/v). The EURL-FCM had developed and validated an analytical method based on HPLC-UV to monitor the homogeneity and stability of the target oligomers in the PT test items and to determine the respective assigned values, as prescribed in ISO 17043, 2010ISO 17043, 2010. The standard operating procedure of the method was provided to the participants and could be used instead of their own routine methods. Laboratory results were rated using z, z' and ζ scores in accordance with ISO 13528, 2015. The standard deviation for proficiency assessment, σpt , was set to 20 % of the respective assigned value, for all the four studied oligomers, based on the perception of experts. A total of 36 participants from 26 countries have registered to the exercise. They received two test items. Solution 1 consisted of food simulant D1 fortified with a known mass fraction of the four oligomers, while Solution 2 was obtained by a migration experiment with PET bottles and food simulant D1 and further fortification of the resulting solution with the four oligomers. The majority of the participating laboratories presented satisfactory results for the four PET and PBT oligomers. For the analysis of Solution 1, 79-88 % of the participants obtained |z (or z')-scores| below 2, while the satisfactory performances ranged from 71 to 85 % for Solution 2. This PT has been organised for the first time at EU level for the analysis of polyester oligomers and confirms that most of the NRLs are able to monitor properly these oligomers in the frame of Regulation (EU) No 10/2011.

Glycolytic depolymerization of PET waste using MP-diol and utilization of recycled product for UV-curable wood coating

Polyethylene terephthalate (PET) waste recycling has become a worldwide research interest for industries and academic institutes due its inevitable environmental impact. The main objective of current research work is to target efficient recycling of PET waste from mineral water bottles by the glycolysis method and subsequent use of the recycled product for value-added coating application. In the present study, we report on MP-diol (2-methyl-1,3-propanediol) which is not explored much for the chemical recycling of PET, having a branched aliphatic diol with two primary hydroxyls, for glycolysis reaction. The reaction parameters were optimized for microwave-assisted technique by varying the ratio of raw materials, reaction time, temperature, and power. The reaction parameters were optimized, and the recycled oligomeric product (OPETMPD) was separated, purified, and characterized by chemical and spectroscopic methods. Subsequently, dimethacrylated oligoesters of PET oligomer (UV oligomer) were synthesized by methacrylation of the glycolyzed PET product (OPETMPD). The synthesized UV oligomer was evaluated using chemical and spectroscopic methods. Ultraviolet (UV) radiation-curable formulations were prepared using synthesized UV oligomer and applied on wooden panels. The coatings were cured using UV-curing machine and evaluated for their performance properties. The partial replacement of UV oligomer in UV formulations exhibited comparative coating performance properties with respect to conventional UV formulation.

Synthesis and film properties of epoxy esters modified with amino resins from glycolysis products of postconsumer PET bottles

Glycolysis of waste polyethylene terephthalate (PET) flakes obtained from grinding postconsumer bottles was carried out at 225–250°C and molar ratios of PET/ethylene glycol were taken as 1/1, 1/1.5, 1/5, and 1/10. Reaction product was extracted by hot water for three times and water‐soluble crystallizable fraction and water‐insoluble fraction were obtained. These fractions were characterized by acid and hydroxyl value determinations, differential scanning calorimeter analysis, and 1H‐NMR analysis. Glycolysis product was used for synthesis of PET‐based epoxy resin. This epoxy resin was used to prepare epoxy ester resins having 40% and 50% oil content. Epoxy ester resin having 40% oil content was modified with urea‐formaldehyde and melamine‐formaldehyde resins for synthesis of epoxy ester–amino resin. Physical and chemical film properties of epoxy ester and modified epoxy ester resins were investigated. All the epoxy ester and modified epoxy ester films were having excellent adhesion, water, and salt water resistance properties. Modification of PET‐based epoxy ester resins with amino resin has significantly improved hardness, impact resistance, and alkaline and acid resistance of resin films. As a result, PET oligomers obtained from glycolysis of postconsumer PET bottles are suitable for manufacturing of amino‐resin‐modified epoxy ester resins that have improved physical and chemical surface coating properties. POLYM. ENG. SCI., 55:2519–2525, 2015. © 2015 Society of Plastics Engineers

Synthesis and Characterization of Polyols and Polyurethane Foams from PET Waste and Crude Glycerol

In this study, polyethylene terephthalate (PET) waste from post-consumer soft-drink bottles and crude glycerol from the biodiesel industry were used for the preparation of polyols and polyurethane foams. PET waste was firstly depolymerized by the glycolysis of diethylene glycol. The glycolyzed PET oligomers were then reacted with crude glycerol at different weight ratios to produce polyols via a series of reactions, such as esterification, transesterification, condensation, and polycondensation. The polyols were characterized by titration, viscometry, gel permeation chromatography (GPC), and differential scanning calorimetry. Subsequently, polyurethane (PU) foams were made via the reaction between the produced polyols and polymeric methylene-4,4′-diphenyl diisocyanate and were characterized by mechanical testing, scanning electron microscopy, and thermogravimetric analysis. Polyols from crude glycerol and their PU foams were also prepared to compare properties with those of polyols and PU foams from PET and crude glycerol. The influence of aromatic segments existing in glycolyzed PET and glycerol content on the properties of the polyols and PU foams was investigated. It was found that aromatic segments of polyols from glycolyzed PET helped increase their molecular weights and improve thermal stability of PU foams, while high glycerol content in polyols increased the hydroxyl number of polyols and the density and compressive strength of PU foams.

Chapter Seven - Synthetic Polyester-Hydrolyzing Enzymes From Thermophilic Actinomycetes

Thermophilic actinomycetes produce enzymes capable of hydrolyzing synthetic polyesters such as polyethylene terephthalate (PET). In addition to carboxylesterases, which have hydrolytic activity predominantly against PET oligomers, esterases related to cutinases also hydrolyze synthetic polymers. The production of these enzymes by actinomycetes as well as their recombinant expression in heterologous hosts is described and their catalytic activity against polyester substrates is compared. Assays to analyze the enzymatic hydrolysis of synthetic polyesters are evaluated, and a kinetic model describing the enzymatic heterogeneous hydrolysis process is discussed. Structure-function and structure-stability relationships of actinomycete polyester hydrolases are compared based on molecular dynamics simulations and recently solved protein structures. In addition, recent progress in enhancing their activity and thermal stability by random or site-directed mutagenesis is presented.

Analysis of specific migration of monomers and oligomers from polyethylene terephthalate bottles and trays according to the testing methods as prescribed in the legislation of the EU and Asian countries

Specific migration levels of monomers and oligomers in polyethylene terephthalate (PET) food containers were determined using HPLC according to the migration testing methods specified by the relevant legislations of the EU and Asian countries (e.g. Korea and Japan). The results of migration from PET bottles and trays using non-fatty simulants under the testing conditions (60 °C/0.5 h) of Asian countries indicated that the values of various monomers and oligomers (TPA, MHET, BHET, A2 group, A3 group, S2 group, S3 group, cyclic dimer, and cyclic trimer) were in between 0.0 and 0.58 μg dm−2. On the other hand, those obtained with the EU conditions (40 °C/10 days) were in the range of 0.0 to 0.94 μg dm−2. The specific migration values of monomers and oligomers into non-fatty simulants tended to be generally higher in testing under the EU conditions than under Asian conditions. Furthermore, when PET samples were tested for migration from fatty foods simulants using n-heptane (at 25 °C/1 h as per Asian conditions) or iso-octane (at 20 °C/48 h as per EU conditions), only cyclic trimer was detected at levels of 0.36 to 1.05 μg dm−2 and 0.05 to 0.55 μg dm−2, respectively. The use of 95% ethanol as an alternative fatty food simulant for the migration tests of PET would be inappropriate, since it might cause overestimated migration compared to the use of other simulants such as n-heptane and iso-octane.

Determination of monomers and oligomers in polyethylene terephthalate trays and bottles for food use by using high performance liquid chromatography-electrospray ionization-mass spectrometry

The types and contents of monomers and oligomers in polyethylene terephthalate (PET) food containers were analyzed using HPLC-ESI-MS after being extracted with 50% acetonitrile or dichloromethane using an accelerated solvent extraction unit. The types of cyclic oligomers were classified into first and second series. The first series represented a type of [TG]n composed of terephthalic acid (TPA; T) and monoethylene glycol (EG; G) at a ratio of 1:1. The second series showed a type of [TG]nG in which a single G unit was substituted by diethylene glycol (DEG; GG). The oligomer level extracted using dichloromethane was measured at 4024–11576 mg kg−1. The first series cyclic oligomers, second series cyclic oligomers and linear oligomers constituted 83.0–90.6%, 7.8–14.7% and 1.3–2.8%, of the total extracted oligomers, respectively. The extracted amounts of TPA, monohydroxyethyl terephthalate and bishydroxyethyl terephthalate using 50% acetonitrile were 3.0–28.2 mg kg−1, 16.8–118.2 mg kg−1 and 3.9–26.7 mg kg−1, respectively. The A2, A3, S2 and S3 groups as modified oligomers were detected as 42.9–221.4 mg kg−1, 17.2–250.3 mg kg−1, 1.1–48.1 mg kg−1 and 1.0–19.8 mg kg−1, respectively. The results of this study demonstrate an advanced analytical approach to determine the residual oligomers and monomers in PET products for food use and imply their potential migration to foodstuffs.