Stearic Research Articles

Insights into effect of lignocellulosic biomass framework types on bio-based shape stable composite phase change materials

The utilization of biomass waste as framework materials to inhibit the leakage of phase change material (PCMs) has gained widespread attention. In this work, three new kinds of shape stable composite phase change materials (sscPCMs) were prepared which combined with stearic acid (SA) and peanut shell powders (PSP), poplar wood powders (PWP), and corn straw powders (CSP), respectively. The influence of lignocellulosic biomass types on the thermal energy storage performance of sscPCMs was studied by comparing three types of sscPCMs. The research results indicated that SA/CSP exhibited superior properties in terms of load capacity and thermal energy storage performance. According to leakage experiments the load capacity of SA/PSP, SA/PWP and SA/CSP was 31.67 %, 44.69 %, and 50.09 %, respectively. The phase change latent heat of SA/PSP, SA/PWP, and SA/CSP was 55.78, 84.27 and 98.47 J/g, respectively. In addition, the relationship between biomass component content and load rates was studied. The results showed that there was a positive correlation between the loading rates of SA and the ratio of holocellulose (cellulose + hemicellulose) to lignin. The results provided a promising approach for the selection of lignocellulosic biomass framework materials.

Exploring the healing power of Pistacia lentiscus stems: insights into extraction methods, polyphenolic composition, and health-promoting activities

ABSTRACT This work aimed to evaluate the effect of different extraction solvents on the polyphenolic content, antioxidant and antibacterial activity of Pistacia lentiscus stems. The results obtained show that the extraction yield depends strongly on the polarity of the solvent and the extraction method. The ethanolic extract had the highest yield in both extraction methods investigated, namely Soxhlet (R = 9.89%) and cold maceration (R = 9.20%). The free radical scavenging activity of the extracts showed that the ethanolic extract had the highest antioxidant activity in both extraction methods with an IC50 = 0.023 mg/mL (cold maceration) and an IC50 = 0.034 mg/ml (Soxhlet). The HPLC analysis of the extracts indicates that gallic acid and catechin are the major phenolic compounds. The FTIR results showed that the shift of the stretching is responsible for O-H and C-H bonding. The GC-MS analysis revealed the presence of stearic acid and palmitic acid methyl ester as main compounds. The bacterial analysis of the extracts showed that the aqueous extract represents the most active one against Staphylococcus aureus and Pseudomonas aeruginosa; on the other hand, no antifungal activity was appreciated. Overall, the results indicate that the investigated extracts might be considered valuable sources of bioactive compounds.

Performance Evaluation and Thermal Stabilization of Photovoltaic Panels Using Phase-Change Materials

Photovoltaic (PV) is a widely used technology that generates power from solar energy. The solar radiations reaching PV panels are converted into electrical energy and heat, however the panel temperature increases, leading to a decrease in performance. This issue can be resolved using cooling methods. Phase-change materials (PCMs) are utilized in passive cooling methods, which do not consume energy, store the heat from the panel and cool them. In this study, sodium acetate trihydrate (PCM-1), palmitic acid (PCM-2), and an eutectic mixture of stearic acid and palmitic acid (PCM-3) were placed in a container and integrated into monocrystalline and polycrystalline PV panels to examine the impact of PCM on various performance metrics including power output, energy efficiency, and PV panel surface temperature. The experiments are carried out in Izmir, which has a hot climate condition in summer months. The solar irradiance of Izmir city and standard test condition of 1000 W/m2 were applied to the panels in the experiments. Results showed that the maximum temperature decreased, compared to the reference panel (without PCM), by 22.84% and 14.4%, respectively, when using PCM-1 and eutectic mixture in the monocrystal panel at 1000 W/m2 in August. The power and efficiency increased by 24.97% and 24.95%, respectively, for the polycrystalline panel in July. These results indicate that PCMs enhanced the cooling and increased the performance of the PV panels with high surface temperatures due to intense solar irradiation.

Effect ratio of stearic acid and oleic acid on characteristics of diclofenac sodium nanostructured lipid carrier

Background: Osteoarthritis treatment generally involves using a Non-steroidal Anti-inflammatory Drug (NSAID), and the most common is Diclofenac sodium. The oral use of diclofenac sodium presents some adverse effects on the gastrointestinal tract. Trans-dermal diclofenac sodium's biological efficacy can be affected by factors including its log P value of 1.13. Nanostructured Lipid Carrier (NLC) may solve these concerns. Objective: This study examined how stearic and oleic acid concentrations customise diclofenac sodium NLC's physicochemical properties. Method: High shear homogenisation was used to compare stearic acid and oleic acid at 6:4, 7:3, and 8:2. Furthermore, the physicochemical properties of diclofenac sodium NLC were assessed, such as organoleptic, particle size and poly-dispersity index, pH, viscosity, zeta potential, entrapment efficiency, profiles of FTIR and DSC. Result: This study found that particle size ranged from 333.60 ± 144.29 to 791.77 ± 85.57, and entrapment efficiency was 89.38 ± 3.69 to 76.96 ± 3.29. Increasing the content of oleic acid as a liquid lipid reduces particle size and improves diclofenac sodium NLC entrapment. According to One-Way ANOVA, the dependent variable was not significantly affected by any independent variables (p-value > 0.05) except for particle size and entrapment efficiency. Conclusion: Stearic acid-oleic acid concentration ratios affect diclofenac sodium NLC's physicochemical properties.

Enhanced hydrogen storage performance of zinc and magnesium cobaltite nanocomposites

Renewable and sustainable energies are vital for the near future. Hydrogen, as a clean energy carrier, is a potential candidate for supplying energy in the foreseeable future. Nowadays, hydrogen storage technology has become a significant issue in the energy sector. In this study, ZnCo2O4/ZnO and MgCo2O4/MgO nanocomposites have been synthesized using the sol-gel method with stearic acid as a complexing agent. Different analyses were studied to examine the crystal structure, morphology, and physical properties of the as-prepared samples, including X-ray diffraction (XRD), Fourier transforms infrared (FT-IR), field emission scanning electron microscopy (FESEM), diffuse reflectance spectroscopy (DRS), and vibrating sample magnetometer (VSM). Various methods have been utilized for hydrogen storage technology. In a pioneering approach, the electrochemical hydrogen storage of samples was compared by the chronopotentiometry technique in KOH (4 M) electrolyte solution. The results reveal that ZnCo2O4/ZnO and MgCo2O4/MgO nanocomposites exhibit excellent discharge capacities of 4240 and 3529 mAh/g, respectively, after 11 cycles.

Composition of fatty acids, phytosterols and total content of antioxidants of Morus L. seeds

This paper presents for the first time the results of studying the total content of antioxidants in the seeds of Morus L. The composition of fatty and steric acids of the seeds of mulberry fruits Morus L. was also studied: polymorphic speciesMorus alba(white-fruited, pink-fruited, black-fruited) andMorus nigra(Khartut variety). As a result of the studies, 12 fatty acids were identified. The main ones were linoleic acid, palmitic oleic acid, and stearic acid. The predominant fatty acid in all samples was linoleic, which varied from 67.5 to 79.0%. 15 sterols were found, among whichβ-Sitosterol accounts for about 90%. Determination of the total antioxidant content ofMorus albaseeds (white-fruited, pink-fruited, black-fruited forms) andMorusnigra(Khartut variety) revealed the accumulation of antioxidants in all samples. The highest total content of antioxidants was observed inMorus nigra(4.40 mg/g) and the white-fruited form ofMorus alba(5.56 mg/g).

Effects of stearic acid on the cryotolerance of the domestic cat (Felis silvestris catus) embryos

The current work aimed to study the effect of domestic cat (Felissilvestris catus) embryosin vitroexposure to saturated stearic acid (SA) and to evaluate how the change in lipid content affects the cryopreservation results. The addition of SA to the culture medium did not affect the development of cat embryosin vitrobefore cryopreservation. The total lipid amount in the SA-treated embryos was not changed as well. However, the lipid unsaturation degree was lower in embryos afterin vitroexposure to SA. Moreover, the lipid phase transition onset temperature (T*) was higher in SA-treated embryos as compared with controls. These changes of intracellular lipids unsaturation degree andT*were associated with the impairment of embryo cryopreservation effectiveness. The results obtained may be of importance for the applying Genome Resource Banking concept to the Felinae species.

Engineering the Integration of Titanium and Nickel into Zinc Oxide Nanocomposites through Nanolayered Structures and Nanohybrids to Design Effective Photocatalysts for Purifying Water from Industrial Pollutants

Water pollution is one of the main challenges currently facing scientists around the world because of the rapid growth in industrial activities. On this basis, 2D nanolayered and nanohybrid structures, which are based on a ternary system of nickel–titanium–zinc, are considered favorable sources for designing effective nanocomposites for the photocatalytic degradation of industrial pollutants in a short period of time. These nanocomposites were designed by modifying two-dimensional nanolayers to produce a three-dimensional porous structure of multi-doped Ni/Ti-ZnO nanocomposites. Additionally, another additive was produced by constructing nanohybrids of nickel–titanium–zinc combined with a series of hydrocarbons (n-capric acid, myristic acid, stearic acid, suberic acid, and sebacic acid). Energy-dispersive X-ray spectrometry, X-ray diffraction, scanning electron microscopy, infrared spectroscopy, and thermal analyses confirmed the growth of the nanolayered and nanohybrid materials in addition to the production of nanocomposites. The positive role of the dopants (nickel and titanium) in producing an effective photocatalyst was observed through a significant narrowing of the band gap of zinc oxide to 3.05–3.10 eV. Additionally, the high photocatalytic activity of this nanocomposite enabled the complete removal of colored dye from water after 25 min of UV radiation. In conclusion, this study proposes an unconventional approach for designing new optical nanocomposites for purifying water. Additionally, it suggests a novel supporting method for designing new kinds of nanohybrids based on multi-metals and organic acids.

Functional and financial analysis of an inclined step solar desalination using phase change nanomaterials

ABSTRACT Recent decades have seen a shortage of water, which has led scientists to concentrate on solar desalination technologies. The present study examines the solar water desalination system with inclined steps, while considering various phase change materials (PCMs). The findings suggest that the incorporation of PCM generally enhances the productivity of the solar desalination system. Additionally, the combination of nanoparticles has been used to PCM, which is a popular technique utilized nowadays to improve the efficiency of these systems. The current investigation involves the transient modeling of a solar water desalination system, utilizing energy conservation equations. The equations were solved using the Runge–Kutta technique of the ODE23s order. The temperatures of the salt water, the absorbent plate of the glass cover, and the PCM were calculated at each time. Without a phase changer, the rate at which fresh water is produced is around 5.15 kg/m2·h. The corresponding mass flow rates of paraffin, n-PCM I, n-PCM III, n-PCM II, and stearic acid are 22.9, 28.9, 5.9, 11.9, and 73 kg/m2·h. PCMs, with the exception of stearic acid, exhibit similar energy efficiency up to an ambient temperature of around 29°. However, at temperatures over 29°, n-PCM II outperforms other PCM.

Microbial Biotechnologies to Produce Biodiesel and Biolubricants from Dairy Effluents

The shift from fossil fuels to renewable energy sources is crucial in addressing environmental challenges. Vegetable oils have been focused on as the main potential source for biodiesel and biolubricant production. However, due to their fatty acid (FA) composition they are characterized by low stability to oxidation and variable viscosity. Single-cell oils (SCOs) from oleaginous microorganisms are a possible alternative to vegetable oils: their composition is more suitable, and it can further be improved by controlling the fermentation’s physiological conditions. In the present study, the production of SCOs with targeted technological properties from Lipomyces starkeyi in fermentation under controlled temperatures was assessed. A dairy effluent (scotta) was used as the fermentation substrate to improve the economic sustainability of the process. Batch aerobic fermentations were carried out in a fermenter at two different temperatures (25 °C and 30 °C). The fermentation yields and SCO FA profiles were analyzed. The highest yields of biomass (9.76 g L−1) and microbial oil (1.83 g L−1) were obtained from fermentations carried out at 30 °C. Furthermore, a significantly lower content (46% vs. 55%) of unsaturated FAs and higher content (11% vs. 1.5%) of shorter-chain saturated FAs, with myristic acid almost matching stearic acid, were detected at 30 °C in comparison to 25 °C. Very low peroxide values were also found (0.14 meq O2 kg−1 at 30 °C and 0 meq O2 kg−1 at 25 °C). These results indicate that these SCOs were highly oxidation-resistant, and that a higher fermentation temperature improves their oxidative stability and tribophysical features. The biodiesels’ technological properties, calculated from the FA composition, were within the limits of both U.S. standards and E.U. regulations. Then, SCOs produced from L. starkeyi by fermentation of dairy effluents carried out under controlled temperature can be considered a suitable alternative to vegetable oils to produce biodiesel and biolubricants.

Ephedra sinica polysaccharide regulate the anti-inflammatory immunity of intestinal microecology and bacterial metabolites in rheumatoid arthritis

IntroductionEphedra sinica polysaccharide (ESP) exerts substantial therapeutic effects on rheumatoid arthritis (RA). However, the mechanism through which ESP intervenes in RA remains unclear. A close correlation has been observed between enzymes and derivatives in the gut microbiota and the inflammatory immune response in RA.MethodsA type II collagen-induced arthritis (CIA) mice model was treated with Ephedra sinica polysaccharide. The therapeutic effect of ESP on collagen-induced arthritis mice was evaluated. The anti-inflammatory and cartilage-protective effects of ESP were also evaluated. Additionally, metagenomic sequencing was performed to identify changes in carbohydrate-active enzymes and resistance genes in the gut microbiota of the ESP-treated CIA mice. Liquid chromatography-mass spectrometry and gas chromatography-mass spectrometry were performed to observe the levels of serum metabolites and short-chain fatty acids in the gut. Spearman’s correlational analysis revealed a correlation among the gut microbiota, antibiotic-resistance genes, and microbiota-derived metabolites.ResultsESP treatment significantly reduced inflammation levels and cartilage damage in the CIA mice. It also decreased the levels of pro-inflammatory cytokines interleukin (IL)-6, and IL-1-β and protected the intestinal mucosal epithelial barrier, inhibiting inflammatory cell infiltration and mucosal damage. Here, ESP reduced the TLR4, MyD88, and TRAF6 levels in the synovium, inhibited the p65 expression and pp65 phosphorylation in the NF-κB signaling pathway, and blocked histone deacetylase (HDAC1 and HDAC2) signals. ESP influenced the gut microbiota structure, microbial carbohydrate-active enzymes, and microbial resistance related to resistance genes. ESP increased the serum levels of L-tyrosine, sn-glycero-3-phosphocholine, octadecanoic acid, N-oleoyl taurine, and decreased N-palmitoyl taurine in the CIA mice.ConclusionESP exhibited an inhibitory effect on RA. Its action mechanism may be related to the ability of ESP to effectively reduce pro-inflammatory cytokines levels, protect the intestinal barrier, and regulate the interaction between mucosal immune systems and abnormal local microbiota. Accordingly, immune homeostasis was maintained and the inhibition of fibroblast-like synoviocyte (FLS) proliferation through the HDAC/TLR4/NF-κB pathway was mediated, thereby contributing to its anti-inflammatory and immune-modulating effects.

Synthesis of Sugar Esters Using Maize Seed Lipase as a Biocatalyst

This work is devoted to the extraction of a lipase from maize seeds obtained at low cost without extensive purification technology and used as a biocatalyst in the synthesis of various sugar esters as potential biosurfactants in the detergent industry. Indeed, several reactions have been carried out between different sugars - namely glucose, galactose, saccharose, lyxose, fructose and sorbitol - and stearic acid in a ratio of 2.5:1 in hexane at 50 °C. Kinetic monitoring of the target reactions was carried out by volumetric analysis in order to determine the conversions (C). The best results obtained were C = 76, 71 and 67% in the presence of glucose, lyxose and galactose, respectively. In addition, HPLC and TLC analyses revealed that for every sugar used two types of esters formed.

Response of yield and its components of two wheat varieties to foliar spraying with stearic acid

Response of yield and its components of two wheat varieties to foliar spraying with stearic acid

Study on lipid and fatty acid composition of \(\textit{Thelenota ananas}\) collected from Bai Dong Island, Ha Long Bay, Vietnam

The paper studies the lipid and fatty acid composition of the sea cucumber Thelenota ananas collected on Bai Dong Island, Ha Long Bay, Vietnam. The total lipid content of dry sample weight was relatively high (11.89%). The triacylglycerol TG has the highest concentration in total lipids with a ratio of up to 66.73%; the PL and PI classes do not have a significant difference with the proportions of 13.44 and 11.65% in total lipids. Two classes of sterol ST, hydrocarbon-wax HW and free fatty acid FFA account for a small proportion. The two main classes of phospholipids are PC and PE, with a ratio of 47.10% and 33.29% of total phospholipids. There are 36 fatty acids identified, of which total saturated fatty acids (SFA) account for 41.61%; Monounsaturated fatty acids (MUFA) account for 32.15%, and polyunsaturated fatty acids (PUFA) account for 25.63%; the main fatty acids are stearic acid (18:0) accounting for 13.15% of the total fatty acids; 16:1n-9 accounts for 14.87%, and 20:5n-3 EPA fatty acids account for 15.3% of the total fatty acids. Among the fatty acids, n-9 (omega 9) accounts for the highest proportion with 25.16%; n-3 fatty acids (omega 3) account for 18.43%; n-6 (omega 6), n-7 (omega 7) fatty acids account for 5.8 and 6.5%, respectively. In this study, the n3/n6 ratio of the sea cucumber sample Thelenota ananas was 3.18%, consistent with the evaluation standards of the World Health Organization (WHO) of n3/n6 ratio ≥ 0.1%. It is classified as a good foodstuff for human health; therefore, it can be considered a source of food that can be used to serve community health care needs.

Synergistic effect of stearic acid/bismuth oxychloride/cupric oxide for thermal storage applications: preparation, stability, rheological and thermophysical analysis

The present study reports the preparation of nanophase change materials (NPCMs) using a two-step method with an optimized ratio of 0.5 wt% of nanoparticles for thermal storage applications. Bismuth oxychloride (BiOCl), cupric oxide (CuO), and a mixture of BiOCl/CuO (composite) were used as nanoparticles, and stearic acid was used as the PCM. The crystallography, chemical/functional groups and morphologies of the prepared NPCMs have been analysed by XRD, FT-IR and SEM, respectively. Observations revealed that the presence of nanoparticles in NPCMs did not affect crystal formation or chemical disruption of molecular interactions. TGA was used to analyse the thermal stability and rate of deterioration of the NPCMs. The deterioration of the PCM occurs at 243 °C with a weight loss of 1.3% while 0.5 wt% concentrated BiOCl, CuO, and composite NPCMs exhibit weight losses of 1.8%, 2.3%, and 3.4%, respectively at 257 °C, 262 °C and 258 °C. In the DSC study, the phase-changing attributes of the NPCMs manifested in the onset temperature range between 53.4 °C and 59.8 °C. The potential enthalpy of the PCM is 209.1 kJ kg−1, whereas those of the 0.5 wt% concentrated BiOCl, CuO, and composite NPCMs are 204.6, 198.3, and 201.7 kJ kg−1, respectively. However, the enhanced thermal conductivities of 0.5 wt% concentrated BiOCl, CuO, and the composite NPCMs are 0.18, 0.22, and 0.20 W/(m.°C), respectively, which are 5.9%, 29.4% and 17.6% greater than that of PCM. Additionally, the congruent melting rate increased by 31% for 0.5 wt% CuO concentrated NPCM; therefore, it is a potential candidate than other NPCMs/PCM. Cyclic tests were conducted to assess the reliability of the NPCMs, and compatible results were obtained even after 500 cycles. The findings of this work indicate that all the prepared NPCMs could be a viable option for practical applications, including thermal comfort buildings, solar heating, and electronic cooling.

Bifidobacterium longum S3 alleviates loperamide-induced constipation by modulating intestinal acetic acid and stearic acid levels in mice.

Constipation is a major gastrointestinal (GI) symptom worldwide, with diverse causes of formation, and requires effective and safe therapeutic measures. In the present study, we used loperamide hydrochloride to establish a constipation model and assessed the effect of Bifidobacterium on constipation and its possible mechanism of relief. The results showed that B. longum S3 exerted a constipation-relieving effect primarily by improving the gut microbiota, enriching genera including Lactobacillus, Alistipes, and Ruminococcaceae UCG-007, and decreasing the bacteria Lachnospiraceae NK4B4 group. These changes may thereby increase acetic acid and stearic acid (C18:0) levels, which significantly increase the expression levels of ZO-1 and MUC-2, repair intestinal barrier damage and reduce inflammation (IL-6). Furthermore, it also inhibited oxidative stress levels (SOD and CAT), decreased the expression of water channel proteins (AQP4 and AQP8), significantly elevated the Gas, 5-HT, PGE2, and Ach levels, and reduced nNOS and VIP levels to improve the intestinal luminal transit time and fecal water content. Collectively, these changes resulted in the alleviation of constipation.

Sunflower germplasms’ response to different water and salinity stress levels in greenhouse and field conditions under subsurface drip irrigation

AbstractSunflower (Helianthus annuus L.) is moderately tolerant to salt and water stress, but its production can still be significantly and adversely affected by increases in these stressors as a result of the negative impacts of climate change on agricultural soil and crop productivity. The morphological and productivity (dry head weight, dry root weight, dry shoot weight, head diameter, whole seed weight, crude protein content, crude oil content, palmitic acid, stearic acid, oleic acid, linoleic acid, eicosanoic acid, 11‐eicosenoic acid, homo‐gamma‐linolenic w6 acid, lignoceric acid and plant height) responses of modern sunflower germplasms to different levels of salt and drought stress under greenhouse and field conditions were investigated and analysed. Six germplasms were evaluated under three salt concentrations (0, 150 and 250 mM), and two germplasms were evaluated for drought response under three irrigation levels. Significant differences in the response of sunflower germplasms to water and salinity were detected. The same germplasms exhibited significant differences in response to water and salinity between the treatments, which also varied significantly between the germplasms for the same treatment. The irrigation level significantly influenced the amount of oil but not the crude protein or fatty acid composition. The results and information of this research can aid in selecting and improving sunflower productivity under adverse (i.e. saline and drought) conditions.

Investigation on the blooming behavior of additives in nitrile butadiene rubber at elevated temperature

AbstractThe degradation of rubber performance in service environments is closely associated with the blooming behavior of additives in the rubber. This study investigates surface precipitates and changes in tensile properties of nitrile butadiene rubber (NBR) after storage at 85°C in air. The morphology, elemental composition, phase composition, and functional groups of the precipitates were analyzed by scanning electron microscopy, energy dispersion spectroscopy, X‐ray diffraction, and fourier transform infrared spectroscopy. Based on the morphology of internal rubber particles and precipitates and variations in the Zn/C mass ratio (ERZn), the reaction between zinc oxide and stearic acid in rubber under long‐term thermal environment was determined. Four stages of blooming for the mixture of zinc oxide and zinc stearate were inferred, and the impact of the blooming on the degradation of tensile properties of NBR was established. A dramatic decrease in the elongation at break (δk) of NBR was correlated with the blooming of zinc stearate and its correspondingly weakened plasticizing effect.Highlights The core‐shell structured mixture of ZnO and Zn(St)2 bloomed onto the surface of nitrile butadiene rubber. The ratio of mass percentages of Zn to C evaluated the blooming process of additives. The migration and blooming process of precipitates were divided into four stages. The decrease in elongation of the rubber was attributed to the blooming of Zn(St)2.

Therapeutic potential of oleic acid supplementation in myotonic dystrophy muscle cell models

BackgroundWe recently reported that upregulation of Musashi 2 (MSI2) protein in the rare neuromuscular disease myotonic dystrophy type 1 contributes to the hyperactivation of the muscle catabolic processes autophagy and UPS through a reduction in miR-7 levels. Because oleic acid (OA) is a known allosteric regulator of MSI2 activity in the biogenesis of miR-7, here we sought to evaluate endogenous levels of this fatty acid and its therapeutic potential in rescuing cell differentiation phenotypes in vitro. In this work, four muscle cell lines derived from DM1 patients were treated with OA for 24 h, and autophagy and muscle differentiation parameters were analyzed.ResultsWe demonstrate a reduction of OA levels in different cell models of the disease. OA supplementation rescued disease-related phenotypes such as fusion index, myotube diameter, and repressed autophagy. This involved inhibiting MSI2 regulation of direct molecular target miR-7 since OA isoschizomer, elaidic acid (EA) could not cause the same rescues. Reduction of OA levels seems to stem from impaired biogenesis since levels of the enzyme stearoyl-CoA desaturase 1 (SCD1), responsible for converting stearic acid to oleic acid, are decreased in DM1 and correlate with OA amounts.ConclusionsFor the first time in DM1, we describe a fatty acid metabolism impairment that originated, at least in part, from a decrease in SCD1. Because OA allosterically inhibits MSI2 binding to molecular targets, reduced OA levels synergize with the overexpression of MSI2 and contribute to the MSI2 > miR-7 > autophagy axis that we proposed to explain the muscle atrophy phenotype.

Phytochemical contents and bioactivity of four endemic Salvia seeds from Turkey: a comparative study to chia seed

AbstractRecently, the importance of medicinal plants such as Salvia species has been increasing both in medicine and in industrial branches, which includes food, feed, and cosmetic raw materials. On the other hand, chia seed is a functional food that has recently increased industrial importance due to its superior nutritional value, phytochemical components, and therapeutic effects. In our study, the antioxidant activity of methanol extracts from the seeds of endemic Salvia cadmica Boiss var. cadmica, and Salvia caespitosa Montbret & Aucher ex Benth., Salvia pisidica Boiss. & Heldr. ex Benth., and Salvia potentillifolia Boiss. & Heldr. ex Benth. collected from Burdur-Antalya/Turkey were determined via 1,1-diphenyl,2-picryl hydrazyl radical scavenging activity, cupric (II) reducing antioxidant capacity, b-carotene/linoleic acid bleaching and total phenolic, and total flavonoid content tests and compared with that of chia seed. Antimicrobial activity was determined according to minimum inhibitory concentration values, on S. aureus, E. coli, S. enterica, L. monocytogenes, C. albicans strains, but it was found negligible. Phenolic and fatty acid contents of the seed extracts were also determined by HPLC and GC–MS, respectively. S. pisidica and S. potentillifolia were found to be highly active. The major fatty acid composition of the chia seed was linolenic acid, linoleic acid, oleic acid, palmitic acid, and stearic acid while the others were linoleic, oleic, palmitic, and stearic acids. Despite fatty acid ratios of chia seed being more favorable; 1,1-diphenyl,2-picryl hydrazyl radical scavenging activity, cupric (II) reducing antioxidant capacity, total phenolic content, and antimicrobial activity of S. pisidica seed extracts and total flavonoid content and inhibition of β-carotene bleaching of S. potentillifolia seed extracts was higher than that of chia seed. These findings suggest seed extracts of these Salvia species are richer in phytochemicals and they are more active as antioxidants when compared to chia seed.