Nutrient Film Technique System Research Articles

Dynamics of micro and macronutrients in a hydroponic nutrient film technique system under lettuce cultivation

While hydroponics is considered an efficient vegetable production system, there is a compelling need to investigate the efficiency of the current generic nutrient dosing recommendation primarily based on electrical conductivity (EC) measurements. Such information is critical to fine-tune and optimize the current hydroponic management practices for improved nutrient uptake efficiency. This study investigated the dynamics of some micro and macronutrients (N, P, Ca, Mg, K, Fe, and Mn) in a recirculating nutrient film technique (NFT) hydroponic system under lettuce cultivation. The research was conducted in an indoor controlled environment growth chamber with lettuce grown in different EC levels (1.2 and 1.6 dS m−1). Each treatment had four hydroponic cultivation units, each one with 24 plants. Nutrient solution and tissue samples were collected two to three times per week. Nutrient dynamics, including nutrient uptake efficiencies and environmental losses, were calculated using a mass balance approach. The effects of EC level on fresh and dry lettuce biomass and nutrient uptake were insignificant. Observed variations in nutrient solution composition during lettuce cultivation included the almost complete removal of ammonia nitrogen, nitrate decreases towards the end of the experiment, consistent increases in aqueous Ca concentration, and corresponding decreases in K and Mn. Average N losses ranged between 27 and 40 %, presumably through denitrification, while 10–14 % of N was assimilated into the plant biomass. The remaining N in the recirculating nutrient solution was estimated to be between 50 and 59 %. The average P loss was 11–35 %, likely due to precipitation, while 52–77 % remained in the nutrient solution. Nutrient uptake efficiencies averaged 19–31 % K, 12–21 % P, 9–16 % Mn, 4–6 % Ca, 3–4 % Mg, and 2–4 % Fe. These results suggest that elevated nutrient concentrations in recirculating nutrient solutions led to losses and underutilization. Findings from this study provide a comprehensive dataset critical to improving hydroponic nutrient management beyond N and P. Hydroponic nutrient management should target providing essential nutrients needed by plants at the correct proportions considering the plant growth stage.

Multicriteria decision-making tool for investigating the feasibility of the green roof systems in Egypt

Urbanization in Egypt detracts from green spaces, reduces the per capita green ratio, and increases adverse effects such as heat islands, air pollution, and energy consumption. In addition, it affects social human comfort issues. In this context, building rooftops is a potential solution that could reduce the impact of green space scarcity. Such a solution has multiple evidence-based environmental, economic, and social benefits. Consequently, numerous governmental and private initiatives have spread the rooftop greening concept in Egypt. These initiatives have adopted several planting systems, such as soil-based, deep-water culture, and nutrient film technique systems. This manuscript examines these prevalent systems through environmental, economic and social lenses. This paper pioneers a user-centric tool to facilitate the system selection that aligns with individual needs. An analysis was conducted to ascertain the value of various factors influencing system choice, encompassing a literature review, expert opinion solicitation, market survey, and energy simulation. The Analytical Hierarchy Processes methodology was proposed to appraise the factors, aiding in arriving at an informed decision. The paper presents a novel contribution by studying many factors spanning diverse scientific domains. Furthermore, creating an accessible decision-support tool encapsulates a substantial addition to the body of knowledge.

Yield, nutrients uptake and lipid profile of the halophyte Salicornia ramosissima cultivated in two different integrated multi-trophic aquaculture systems (IMTA)

The nutrient removal, biomass production and nutritional value of the halophyte Salicornia ramosissima were evaluated in the context of an Integrated Multi-Trophic Aquaculture (IMTA) system. The experiment consisted of an indoor fish RAS whose effluent was used to feed two different halophyte hydroponic systems: a Nutrient Film Technique (NFT) system or a Deep Water Culture (DWC) system. The highest yield of S. ramosissima was observed in the DWC (320 g m−2 day−1), this system showed significantly higher yields compared to the NFT. Both hydroponic systems were effective in removing nutrients from the fish RAS wastewater, contributing to the wastes valorization process. Maximal nutrient uptake efficiencies were: 82.8% and 68.6% NO3− in the DWC and the NFT, respectively; 72.6% PO43− in the DWC and 82.9% in the NFT; 63.6% NO2− in the DWC vs 56.4% in the NFT; and 89.2% NH4+ in the DWC vs 94.1% in the NFT. The lipid profile of the halophytes in the DWC was analysed. The total lipid content ranged from 2.99% to 3.83%. The fatty acids (FA) profile in the leaves was dominated by polyunsaturated fatty acids (about 66%), which were represented by α-linolenic acid (41%) and linoleic acid (24%), followed by saturated fatty acids (28%) with palmitic acid (22%) as the major component. A small component of monounsaturated fatty acids accounts for about 12% of total FA. Regarding lipid classes, pigments were the most abundant compounds followed by glycolipids, phospholipids, flavonoids and sterols. The study supports the potential of S. ramosissima to valorise aquaculture wastes and its high nutritional interest. The experimental systems minimized waste and maximized resources utilization. Such integrated approaches can contribute to the sustainability and resilience of aquaculture systems while providing additional economic opportunities through the production of high value halophyte products.

Ammonium to total nitrogen ratio affects the purslane (Portulaca oleracea L.) growth, nutritional, and antioxidant status

Purslane (Portulaca oleracea L.) is a widespread weed, which is greatly appreciated for its high nutritional value. The present work evaluated the effect of different ammonium/total nitrogen ratios (NH4/Total N: Nr 0.01–0.15) on growth, physiological and biochemical parameters, and nutrient accumulation in different plant parts of hydroponically grown purslane, under two growing seasons, spring and autumn. Young seedlings of purslane were transferred to a Nutrient Film Technique (NFT) system and they were exposed to different Nr levels. The pH and the electrical conductivity of the nutrient solution were kept constant at 5.8 and 2.3 mS cm−1, respectively. After the end of the cultivation periods (19 days for spring and 22 days for autumn), a series of assessments (growth parameters, mineral content in different plant organs, antioxidant status of the plant, etc.) were done. Plant height, leaf number, root fresh weight and plant biomass revealed decreased trends at the higher NH4/total N ratios, especially during the autumn growing season. Total phenols, flavonoids and antioxidant capacity appeared increased at Nr ≤ 0.10 during both seasons (autumn and spring), revealing higher nitrogen accumulation rates and increased water and nutrient use efficiency. Purslane plants grown in Nr 0.05–0.10 revealed a less intense oxidative stress, with decreased lipid peroxidation levels that was the result of the activation of both enzymatic (superoxide dismutase, catalase and peroxidase) and non-enzymatic (ascorbic acid) antioxidant capacity of the plant. Increased Nr resulted in the accumulation of potassium, while calcium and magnesium levels in leaves were decreased. Additionally, the greater water use efficiency was measured for plants grown under Nr 0.01–0.05. Therefore, the recommended ammonium/total nitrogen ratio for purslane production of increased yield, improved nutritional value and efficient use of water and nitrogen sources is to employ Nr of 0.05, while additional care should be addressed during autumn periods as plants are subjected to greater impacts of the Nr ratio.

Investigating the potential of growing crops hydroponically utilizing feed and draw solutions from fertilizer drawn forward osmosis

This study investigated the potential of utilizing both the draw and feed solutions resulting from fertilizer drawn forward osmosis for hydroponic crop cultivation. Synthetic brackish groundwater of 2500 ppm was used as the feed solution, whereas commercial hydroponic nutrients, sourced from a local supplier, were utilized as a draw solution. This study also investigated the potential of integrating nanofiltration with forward osmosis, but supplementing the water necessary for further dilution of draw solutions through nanofiltration. Two crops were selected, i.e., cherry tomatoes and spinach grown at different water salinities, for their economic values. The cherry tomatoes were grown in Deep Water Culture hydroponic systems, while the spinach was grown in Nutrient Film Technique systems. If this application is deemed feasible, it allows for providing a method to grow two different crops in areas associated with non-arable land and brackish groundwater. During desalination, it was observed that there were two groups of flux readings, the first with an average flux of 7 to 9 l/m2/h, and the other with an average flux of 4 to 6 l/m2/h. This was due to using the same draw solution twice; once to concentrate the feed solution to 5000 ppm, and then once more to concentrate the feed solution to 3500 ppm. It was found that while the 3500 ppm cherry tomatoes tables had the highest yield and highest number of tomatoes throughout the plants lifetime, tomatoes from freshwater tables on average weighed more by about 19%, while, on average, 5000 ppm tomatoes weighed less than 3500 ppm tomatoes by 10%. The results of the spinach demonstrated that while both control and experiment groups yielded similar number of leaves, the average yield per plant for the experiment group was higher than the control group (by 25%).

URBAN FARMING: SOLAR NUTRIENT FILM TECHNIQUE SYSTEM

Farming in urban areas is recognized as a sustainable approach towards the provision of food, and it has increased in Malaysia over recent years. Urban farming has emerged as one approach to contribute to local food security by increasing the availability and accessibility of fresh and healthy produce. Solar Nutrient Film Technique System is a product that can overcome challenges for agriculture sector at urban area. This product objective are to reduce the cost of living, to improvement of food self-sufficiency, to minimize water usage, to create environmentally friendly product and to provide space for agriculture activities for urban area. The novelty and uniqueness of NFT are it can be grown outdoors, indoors even in small space. Furthermore, the NFT is the cultivation of plants without using soil. Vegetables are planted in inert growing media and supplied with nutrient-rich solutions, oxygen, and water by using the electric pump. The application of solar pump also can reduce the cost of electricity and save the environment. Due to challenges of life in an urban environment where the time and space for gardening are limited, the innovation idea of hydroponics system will help the people to plant their fresh produce even though in the city. It creates commercialization potential to individual or company to start on agriculture production. Hydroponic agriculture using the Solar NFT System could be an option for meeting the world's growing food demand. One of the aspects to consider is the nutritional needs of the hydroponic plant. The NFT hydroponic nutrient controlling system is designed to help farmers manage the proper amount of nourishment for their plants. To manage the amount of nutrients, this system use the linear regression method. The precision gained from the controlling system experiment is 87.84%.

Root-applied glycinebetaine controls nitrate content and edible quality of lettuce in continuous commercial hydroponic greenhouse production

Lettuce (Lactuca sativa L.) may accumulate high amounts of nitrate NO3− in hydroponic cultivation, such as in the Nutrient Film Technique (NFT) system. The NFT system is a commonly used hydroponic cultivation method in which a thin layer of nutrient solution flows continuously over the roots and is then recirculated. Since NO3− is known to be harmful to human health, lettuce producers need methods for controlling it and improving the quality of lettuce. Here, we investigated whether root-applied glycinebetaine (GB) can be used to control the NO3− content in commercial-scale greenhouse production. Three commercial-scale experiments were conducted with different GB application rates (0, 4, 7.5, and 10 + 10 mM GB). Glycinebetaine was applied to the nutrient solution, and lettuce was exposed to the GB treatment during the last 6 growing days before the harvest. Even though the root-applied GB slightly reduced the fresh weight of harvested lettuce and some minerals in lettuce dry matter, it significantly reduced the lettuce NO3− content (over 29%) and increased the contents of some amino acids in comparison to untreated plants. Thus, the edible quality of lettuce was improved. Furthermore, the tested GB application method proved to be functional on a commercial scale. Based on our study, adding GB to the nutrient solution can be considered a practical method for controlling lettuce NO3− content.

Inoculation reduces nitrate accumulation and increases growth and nutrient accumulation in hydroponic arugula

Inoculation with plant growth-promoting bacteria (PGPBs) has remarkably increased yield and nutrient uptake of crop plants. The objective of this study was to evaluate the effect of bacterial inoculation with Azospirillum brasilense, Bacillus subtilis and Pseudomonas fluorescens on growth, accumulation of nutrients as well as NNH4+ and NNO3− in hydroponic arugula plants. The research was carried out in a nutrient film technique (NFT) system and designed in randomized blocks with 5 replications. The treatments consisted of inoculation with A. brasilense, B. subtilis and P. fluorescens via nutrient solution at a dose of 0.1 mL L−1 and without inoculation treatment. Inoculation with P. fluorescens promoted NNH4+ accumulation in shoots and roots by 311% and 119% respectively as compared to non-inoculated plants. Inoculations with A. brasilense, B. subtilis and P. fluorescens reduced NNO3− accumulation in shoots and roots by18 and 14% as compared to without inoculation treatments. Fresh and dry mass of roots, root volume and leaf chlorophyll index were increased with inoculation of P. fluorescens and being considered the most suitable inoculant for hydroponic arugula cultivation. Inoculation with A. brasilense, P. fluorescens and B. subtilis reduced shoot NNO3− accumulation, thus benefiting human health.

Tocopherols, Phylloquinone, Ascorbic Acid, and Sugar Contents in Hydroponically Grown Lettuce

Growing vegetables in controlled environments (CEs), such as hydroponics, aquaponics, and vertical structures, is a rapidly expanding industry in Florida and the United States, especially in nearby urban areas. Although lettuce (Lactuca sativa) is still mostly produced in fields, growing in CEs proximal to urban areas has become increasingly popular because it may facilitate reduced transportation time and associated postharvest degradation. Lettuce is among the top-most consumed vegetables in the United States and could provide some of the nutrition missing in the US diet. This research was planned to understand the levels of some vitamins that are key for human health, including vitamin E (tocopherols), vitamin K1 (phylloquinone), and vitamin C (ascorbic acid), in lettuce grown in greenhouse hydroponics. Lettuce germplasm was grown using the hydroponic nutrient film technique system in three greenhouse experiments: at the beginning, middle, and end of the Florida, USA, growing season (from Aug 2020 to Mar 2021). Genetic variation for these vitamins were found among the germplasm tested in the four morphological types of lettuce, romaine, Boston, Latin, and leaf. In addition, a sugar analysis was conducted in this germplasm, of which fructose was the most abundant sugar. A significant genotype × environment (G × E) interaction was observed, indicating that the levels of these compounds, especially vitamins, was environment dependent. However, the presence of certain non-crossover G × E interactions indicates that selecting lettuce in a representative environment could result in new cultivars with higher vitamin content. This research marks the initial steps to improve lettuce for these vitamins, which can contribute to better health of US consumers, not for the highest amount of these compounds in lettuce but for the offset due to its high consumption.

Identifying Lettuce Accessions for Efficient Use of Phosphorus in Hydroponics

Lettuce (Lactuca sativa L.) is the most common leafy vegetable produced hydroponically in the United States. Although hydroponic systems are advantageous due to lower pest and disease pressure, and reduced water and nutrient requirements, the increasing prices of fertilizers, including phosphorus (P), still influences the profitability of hydroponic production of lettuce. Characterizing lettuce germplasm capable of producing high yield using less P inputs may help reduce fertilizer use, production costs, and P loads in wastewater. In this study, 12 lettuce accessions were grown in four experiments in a nutrient film technique system. In the first two experiments, the treatments consisted of two P concentrations (3.1 and 31 mg·L−1). Lettuce cultivated with 3.1 mg·L−1 of P had variable shoot and root biomass, root–shoot ratio, P uptake efficiency, and P utilization efficiency, indicating the existence of genetic variation. Five accessions (‘Little Gem’, 60183, ‘Valmaine’, BG19-0539, and ‘Green Lightning’) were considered efficient to P because produced similar shoot biomass with the low and high P treatments. In the third and fourth experiments, the treatments consisted of two P sources (monosodium phosphate (NaH2PO4) and tricalcium phosphate [TCP; Ca3(PO4)2]. Initially, extra 5 mM of calcium (Ca) was added to the TCP solution to reduce the TCP solubility and, hence, P bioavailability to plants. All accessions produced similar shoot and root weight with both treatments, indicating that the TCP treatment did not cause low-P stress to the plants. After, the extra Ca concentration added to TCP was increased to 10 mM, resulting in low-P stress and a significant reduction in shoot weight of all accessions. Despite the severe P stress, ‘Little Gem’ and 60183 were among the accessions with the least shoot weight reduction in the TCP treatment. Variability was observed in root biomass root–shoot ratio among accessions under the TCP treatment, suggesting that lettuce accessions responded differently to P stress conditions. The genetic variation for P use efficiency (PUE) and PUE-related traits in lettuce grown hydroponically suggests the feasibility of breeding new lettuce cultivars from elite lettuce germplasm adapted to low P availability in hydroponics.

Analysis of Red Onion Hydroponic Cultivation Case Study at Fresh Hydroponic MSMEs

The purpose of the study is to find out the process of cultivating shallots using hydroponic techniques. The location of the study was conducted in Kedamean District, Gresik Regency, precisely Turirejo Village, which has fresh hydroponic Micro, Small and Medium Enterprises (MSMEs). The determination of the location of the study was carried out purposively, namely carried out on fresh hydroponic MSMEs with a business of cultivating shallot commodities hydroponically without using green houses or shade. The data used by researchers are primary and secondary data. The research method uses a descriptive method that uses survey methods, in-depth interviews and observations as data collection techniques. The results of the analysis of the hydroponic cultivation process of fresh hydroponic MSMEs are cultivating hydroponic shallots with the Nutrient Film Technique (NFT) system. It consists of 2 stages including, seedbed installation and enlargement installation. The cultivation process is carried out in an open place, namely the yard of the house or not using a greenhouse. The hydroponic cultivation process in fresh hydroponic MSMEs starts from the preparation of cultivation, the process of cultivating shallot hydroponics and post-harvest handling. Preparation for hydroponic cultivation of shallots includes capital, land, labor and saprodi. The next stage is in the cultivation process, including 1) Seeding seedlings, 2) Transplanting, 3) maintenance: (fertilization embroidery, watering, opt control) 4) Harvesting. Post-harvest handling in the hydroponic cultivation of shallots, namely withering and drying.

A Potential Application of Pseudomonas psychrotolerans IALR632 for Lettuce Growth Promotion in Hydroponics.

Controlled environment agriculture hydroponic systems grow plants year-round without restriction from outside environmental conditions. In order to further improve crop yield, plant growth-promoting bacteria were tested on hydroponically grown lettuce (Lactuca sativa) plants. From our bacterial endophyte library, we found one bacterium, Pseudomonas psychrotolerans IALR632, that is promising in promoting lettuce growth in multiple hydroponic systems. When Green Oakleaf lettuce seeds were inoculated with IALR632 during germination, IALR632 significantly increased lateral root development by 164%. When germinated seedlings were inoculated with IALR632 and then transplanted to different hydroponic systems, shoot and root fresh weights of Green Oakleaf increased by 55.3% and 17.2% in a nutrient film technique (NFT) system in the greenhouse, 13.5% and 13.8% in an indoor vertical NFT system, and 15.3% and 13.6% in a deep water cultivation (DWC) system, respectively. IALR632 also significantly increased shoot fresh weights of Rex by 33.9%, Red Oakleaf by 21.0%, Red Sweet Crisp by 15.2%, and Nancy by 29.9%, as well as Red Rosie by 8.6% (no significant difference). Inoculation of IALR632-GFP and subsequent analysis by confocal microscopy demonstrated the endophytic nature and translocation from roots to shoots. The results indicate that P. psychrotolerans IALR632 has a potential application in hydroponically grown lettuce plants.

Nutrient Film Hydroponic System Techniques for Pid-Based Strawberry Growth

Surabaya is an urban area with limited land for farming, because there are many buildings. Farming requires a largearea and fertile soil. With the development of agricultural technology today, there is a new method of planting calledHydroponics. There are several types of hydroponic systems, namely Aeroponics (fog system) and Nutrient FilmTechnique (NFT). In this article, the writer uses NFT technique. NFT is a system that has a farming concept bychanneling nutrients to plant roots in a film or thin so that plants get food nutrients, namely water and oxygen. Theadvantage of using this NFT system is that it makes it easier to control plant nutrients and plant growth is fasterbecause plant roots are free to absorb nutrients to the maximum. From the results of the research conducted, the pHsetpoint value was 6.0. From the results of the research conducted, set point pH values of 6.4 and 5.8. From the testresults, the Ziegler Nichols method of type 1 for a setpoint of 6.4 gets a value of L=3 and T=22.44 and a setpoint valueof 5.8 gets a value of L = 3 and T = 23.76. After that, the setpoint 6.4 got the value of Kp = 8.976 Ki = 1.496 Kd =13,464 and the setpoint of 5.8 got the value of Kp = 9.504 Ki = 1.584 Kd = 14,256. 1. The setpoint value of 6.4overshoot is 8.37% rise time 20 s, and settling time is 45 s. The setpoint value of 5.8 overshoot is 6.89% rise time 25s, and settling time is 55 s.

Effect of biochar as a hydroponic substrate on growth, colour and nutritional content of red lettuce (Lactuca sativa L.)

Hydroponic is a technique of growing plants in a soilless medium by using a sponge, rock wool, hydroton, coconut coir, and perlite as an alternative for crop production systems. Recently, biochar has been reported to be a potential substrate for hydroponic cultivation techniques due to its physicochemical properties which can help increase vegetable production. A greenhouse study was conducted to investigate the effect of biochar as hydroponic substrate on the growth, colour and nutritional content of red lettuce (Lactuca sativa L.). This study utilized the nutrient film technique (NFT) hydroponic system and was conducted using a randomized complete block design with five treatments, including T1 (hydroton only), T2 (perlite only), T3 (palm kernel biochar), T4 (palm kernel biochar + hydroton), and T5 (palm kernel biochar + perlite). Data analysis revealed the treatment, which consists of both palm kernel biochar and hydroton (T4) resulted in a significant increase in plant growth and yielded the highest plant height (19.86 cm), leaf width (14.16 cm), plant fresh weight (68.19 g), and dry weight (8.29 g). The leaves nutrient content (N, P, K, Mg, Ca) of red lettuce grown in palm kernel biochar and hydroton (T4) substrates suggested the presence of optimal growth conditions for ensuring optimum yield with high quality. The application of palm kernel biochar and hydroton (T4) as substrate also showed a higher lightness value (L* = 66.67). Besides, the methanolic leaf extracts from the red lettuce grown in palm kernel biochar and hydroton (T4) showed the highest bioactive metabolite content. In addition, the application of palm kernel biochar (T3) as a hydroponic substrate decreased the algal density in the nutrient solution. In conclusion, the combination of palm kernel biochar and hydroton as a substrate was observed to be the best in enhancing the growth performance, colour, and nutritional content of red lettuce (Lactuca sativa L.), and it is therefore recommended to be used as the growth substrate in the NFT system.

Hyperspectral Image Data and Waveband Indexing Methods to Estimate Nutrient Concentration on Lettuce (Lactuca sativa L.) Cultivars.

Lettuce is an important vegetable in the human diet and is commonly consumed for salad. It is a source of vitamin A, which plays a vital role in human health. Improvements in lettuce production will be needed to ensure a stable and economically available supply in the future. The influence of nitrogen (N), phosphorus (P), and potassium (K) compounds on the growth dynamics of four hydroponically grown lettuce (Lactuca sativa L.) cultivars (Black Seeded Simpson, Parris Island, Rex RZ, and Tacitus) in tubs and in a nutrient film technique (NFT) system were studied. Hyperspectral images (HSI) were captured at plant harvest. Models developed from the HSI data were used to estimate nutrient levels of leaf tissues by employing principal component analysis (PCA), partial least squares regression (PLSR), multivariate regression, and variable importance projection (VIP) methods. The optimal wavebands were found in six regions, including 390.57-438.02, 497-550, 551-600, 681.34-774, 802-821, and 822-838 nm for tub-grown lettuces and four regions, namely 390.57-438.02, 497-550, 551-600, and 681.34-774 nm for NFT-system-grown lettuces. These fitted models' levels showed high accuracy (R2=0.85-0.99) in estimating the growth dynamics of the studied lettuce cultivars in terms of nutrient content. HSI data of the lettuce leaves and applied N solutions demonstrated a direct positive correlation with an accuracy of 0.82-0.99 for blue and green regions in 400-575 nm wavebands. The results proved that, in most of the tested multivariate regression models, HSI data of freshly cut leaves correlated well with laboratory-measured data.

Effects of Hydraulic Retention Time of Aquaculture Effluent on Nutrient Film Technique Lettuce Productivity

Nutrient film technique (NFT) is a popular, ergonomic, hydroponic system, but is not often used in commercial aquaponic systems due to lower efficiency in overall nutrient removal. Experiments were conducted to assess if NFT lettuce production could be improved by exchanging aquaculture effluent more frequently, and if so, determine the optimal water exchange rate. The AE was taken from a biofloc-based nile tiapia production system. Treatments consisted of increasing hydraulic retention time (HRT (d)) viz: four-, eight-, twelve-, or sixteen-day water exchanges arranged in a randomized complete block design with five blocks. In one trial (trial 1) where iron (Fe) was not supplemented, there was one replication. There were three replications for the second trial with iron supplementation. The analysis of lettuce plant size index and chlorophyll index (SPAD units) in trial 1 was statistically different among the HRTs beginning 14 days after planting, exhibiting negative linear trends with increasing HRT. However, most foliar micronutrients were borderline sufficient, and all treatments showed foliar Fe deficiency. After iron supplementation (trial 2), lettuce plant chlorophyll and size index exhibited quadratic trends with increasing HRT on 14 and 21 DAP, respectively. In trial 2, plant fresh mass decreased linearly from 162.1 g/head to 147.1 g/head, with increasing HRT. Furthermore, iron supplementation eliminated Fe deficiencies in the plants albeit only up to 14 DAP. Our findings suggest that shorter hydraulic retention times provide a solution to using the NFT system in aquaponics especially with iron supplementation.

Cultivation of Water Spinach (Ipomoea Reptans Poir) Production By Using Dft and Nft

Water spinach (Ipomoea reptans Poir) is one of the horticultural crops known for its very easy cultivation and fast harvest cycle and high nutritional value. This plant can be produced or cultivated hydroponically using NFT (Nutrient Film Technique) and DFT (Deep Flow Technique) systems. Cultivation of plants in the NFT system uses a sloping circuit with shallow nutritious water that circulates for 24 hours at a fast flow. The DFT system uses a closed-circuit insulated with stagnant water that circulates for 24 hours at a slow flow. Thus, this research was conducted to determine the differences in the production of water spinach in two hydroponic systems, namely NFT and DFT. The research was conducted using a Randomized Block Design (RAK) and observation method by observing plant height, number of leaves, wet weight, and root length. Data were analyzed using independent samples T-test with a prerequisite test in the form of the Shapiro-Wilk normality test. The results of this research showed that the cultivation of water spinach using NFT and DFT hydroponic systems had significant differences in plant height, number of leaves, root length, and wet weight. Water spinach production can be increased by using DFT compared to NFT.

Case Study Of Dft (Deep Flow Technique)- Nft (Nutrient Flow Technique) Hydroponic Planting Patterns In First Middle School Students State 1 And 5 Karangploso Malang

Farming patterns for urban residents to cultivate crops is a difficult thing to do because of limited land. Currently, the pattern of building residents of the city is apartments and minimalist housing where residents have a narrow land area, critical landconditions and limited amount of water. Therefore, a solution is needed so that city residents can cultivate crops. Based on this, the hydroponic planting pattern is a good alternative for city residents so that they can continue to grow crops in their surrounding environment. The Deep Flow Technique (DFT) method combined with the Nutrient Film Technique system. The purpose of this service activity is the first to organize training on the manufacture of simple DFT-NFT hydroponics, with methods and materials that are safe to use and serve as material for debriefing and providing entrepreneurial motivation for community groups in Malang district. The implementation of this service is at SMP N 1 and SMPN 5 Karangploso, Malang Regency. The webinar participants were attended by 61participants consisting of 8th and 9th grade students, accompanying teachers, and a team of service lecturers. As for the results of this activity 81% of the webinar participants are familiar with the pattern of farming using the DFT NFT hydroponic system well. So that participants have benefited from this activity and these academics are able to apply knowledge to society significantly

Physiology and yield of ‘Gaúcho’ melon under brackish water and salicylic acid in hydroponic cultivation

In order to study the effect of salicylic acid concentrations on the mitigation of salt stress in melon plants grown on a hydroponic system an experiment was conducted in a greenhouse at Pombal – PB, Brazil, using an NFT (Nutrient Film Technique) system. The experimental design was completely randomized, in a 4 × 4 factorial scheme, corresponding to four levels of electrical conductivity of the nutrient solution—ECns (2.1—control, 3.2, 4.3, and 5.4 dS m−1) and four concentrations of salicylic acid—SA (0, 1.5, 3.0, and 4.5 mM), with six replicates. Salicylic acid at the concentration of 3.2 mM attenuated the effect of nutrient solution salinity on the fresh weight of melon fruits. The saline nutrient solution impairs gas exchange and the relative water content and increases the intercellular electrolyte leakage in the leaf blade of melon plants. However, salicylic acid attenuates the deleterious effects of salinity and attains a maximum yield of melon fruits of 23.82 t ha−1 with foliar application of 1.5 mM at ECns of 3.1 dS m−1. Salicylic acid stimulated the synthesis of total chlorophyll, the CO2 assimilation rate, and the instantaneous water use efficiency of hydroponic melon up to a concentration of 4.5 mM. The results obtained indicate that the responses of the hydroponic melon plant grown with saline nutrient solution and the application of salicylic acid are not yet fully elucidated.

Applying Different Magnetic Water Densities as Irrigation for Aeroponically and Hydroponically Grown Strawberries

Due to the scarcity of water, it is necessary to develop an environmentally friendly method for increasing water productivity and crop production. An experiment was conducted to assess the effects of different magnetic levels (magnetic water level 1 (MWL 1) = 3800 Gauss, magnetic water level 2 (MWL 2) = 5250 Gauss, and magnetic water level 3 (MWL 3) = 6300 Gauss, as well as normal water (NW) as a control) in combination with three soilless culture systems (a nutrient film technique (NFT) hydroponics system, a tower aeroponics system, and a pyramidal aeroponics system. The results showed that the utilization of magnetic water had significant effects on the yield and growth of strawberry plants The tower aeroponic system under MWL 3 produced the highest yield and water productivity, with increases of 80.9% and 89%, respectively, over the control. The tower aeroponic system under MWL 3 produced the highest yield and water productivity, with increases of 80.9% and 89%, respectively, over the control. In addition, as compared to the NW, the NFT system increased yield and water productivity by 71.1% and 79.3%, respectively, whilst the pyramidal system increased yield and water productivity by 66.87% and 82%, respectively. Furthermore, when compared to the control, the combination of the NFT system and magnetic water level 3 (MWL 3) resulted in the most leaves, largest stem diameter, and largest leaf area of the strawberry plants resulted in the most leaves, stem diameter, and leaf area of strawberry plants. In comparison to all other treatments, this combination produced the best fruit quality and yield, as well as its constituents, such as titratable acidity, total soluble solids, and fruit hardness. This study found that combining magnetic therapy with soilless culture techniques resulted in increased yield and water productivity. In addition, water and fertigation solution usage in the NFT, tower, and pyramidal systems dropped by 4.8%, 6%, and 4.8%, respectively. Furthermore, it enhanced plant morphology and plant quality.