Nonreturn-to-zero Differential Phase-shift-keying Signals Research Articles

Experimental Investigation of All-Optical NRZ-DPSK to RZ-DPSK Format Conversion Based on TOAD

We propose and experimentally demonstrate a novel all-optical non-return-to-zero differential-phase-shift-keying (NRZ-DPSK) to return-to-zero differential-phase-shift-keying (RZ-DPSK) format conversion scheme. This scheme is based on the terahertz optical asymmetric demultiplexer (TOAD). A 10 Gb/s converted RZ-DPSK signal is obtained with a wide duty cycle tuning range from 16% to 66%. For all converted RZ-DPSK signals, the receiver sensitivities at BER of 10−9 are 0.4 to 1.7 dB higher compared with the original NRZ-DPSK signal. The clear and open eye diagrams are presented to demonstrate the high quality format conversion performance. Moreover, the optical spectra show that this conversion is in a wavelength-preserving operation.

All-optical encryption/decryption for nonreturn-to-zero differential phase-shift keying signals using four-wave mixing in semiconductor optical amplifier

By experiment we demonstrate an all-optical encryption/decryption scheme for nonreturn-to-zero dif- ferential phase-shift keying (NRZ-DPSK) signals at 10 Gbit∕s using all-optical exclusive-OR (XOR) logic. The key bit stream is performed by a pseudorandom bit stream. The all-optical XOR logic is achieved by nonde- generate four-wave mixing (FWM) in a semiconductor optical amplifier (SOA), which allows high data rate oper- ation and asymmetric optical powers of the two input bit streams. The gain dynamics and pattern effect associated with the SOA carrier lifetime are alleviated due to the constant envelope of the NRZ-DPSK signals.

Experimental demonstration and devices optimization of NRZ-DPSK amplitude regeneration scheme based on SOAs.

We propose and experimentally demonstrate a novel scheme which can simultaneously realize wavelength-preserving and phase-preserving amplitude noise compression of a 40 Gb/s distorted non-return-to-zero differential-phase-shift keying (NRZ-DPSK) signal. In the scheme, two semiconductor optical amplifiers (SOAs) are exploited. The first one (SOA1) is used to generate the inverted signal based on SOA's transient cross-phase modulation (T-XPM) effect and the second one (SOA2) to regenerate the distorted NRZ-DPSK signal using SOA's cross-gain compression (XGC) effect. In the experiment, the bit error ratio (BER) measurements show that power penalties of constructive and destructive demodulation at BER of 10-9 are -1.75 and -1.01 dB, respectively. As the nonlinear effects and the requirements of the two SOAs are completely different, quantum-well (QW) structures has been separately optimized. A complicated theoretical model by combining QW band structure calculation with SOA's dynamic model is exploited to optimize the SOAs, in which both interband effect (carrier density variation) and intraband effect (carrier temperature variation) are taken into account. Regarding SOA1, we choose the tensile strained QW structure and large optical confinement factor to enhance the T-XPM effect. Regarding SOA2, the compressively strained QW structure is selected to reduce the impact of excess phase noise induced by amplitude fluctuations. Exploiting the optimized QW SOAs, better amplitude regeneration performance is demonstrated successfully through numerical simulation. The proposed scheme is intrinsically stable comparing with the interferometer structure and can be integrated on a chip, making it a practical candidate for all-optical amplitude regeneration of high-speed NRZ-DPSK signal.

All-Optical Wavelength-Shift-Free NRZ-DPSK to RZ-DPSK Format Conversion with Pulsewidth Tunability by an SOA-Based Switch

We demonstrate an all-optical non-return-to-zero differential phase shift keying (NRZ-DPSK) to return-to-zero differential phase shift keying (RZ-DPSK) format conversion with wavelength-shift-free and pulsewidth tunable operations by using a semiconductor optical amplifier (SOA)-based switch. An NRZ-DPSK signal is injected into the SOA-based switch with an RZ clock, and is converted to RZ-DPSK signal owing to the nonlinear effects inside the SOA. In this scheme, the wavelength of the converted RZ-DPSK signal is maintained as the original wavelength of the input NRZ-DPSK signal during the format conversion. Moreover, the pulsewidth of the converted signal is tunable in a wider operating range from 30 to 60 ps. The format conversion with pulsewidth tunability is based on cross-phase modulation (XPM) and cross-gain modulation (XGM) effects in the SOA. The clear eye diagrams, optical spectra and the bit-errorrate (BER) characteristics show high conversion performance with the wide pulsewidth tuning range. For all cases of the converted RZ-DPSK signal with different pulsewidths, the receiver sensitivities at a BER of 10−9 for the converted RZ-DPSK signal were 0.7 to 1.5 dB higher than the receiver sensitivity of the input NRZ-DPSK signal. key words: Differential phase shift keying (DPSK), format conversion, wavelength-shift-free, pulsewidth tunable operation, cross-phase modulation (XPM), cross-gain modulation (XGM)

Fiber-based optical parametric amplif ier for 40-Gb/s NRZ-DPSK signal transmission system employing QC-LDPC codes

In this letter, we investigate quasi-cyclic low-density parity-check (QC-LDPC) codes in a 40-Gb/s nonreturn-to-zero differential phase-shift keying (NRZ-DPSK) signal transmission system based on a fiber-based optical parametric amplifier (FOPA). A constructed algorithm of QC-LDPC codes according to the optimizing set of shift values on the circulant permutation matrix (CPM) of the basis matrix is proposed. Simulation results prove that the coding gain in the encoded system can be realized at 10.2 dB under QC-LDPC codes with a code rate of 5/6 when the bit error rate (BER) is 10-9. In addition, the error-floor level originating from the uncoded system is suppressed.

Chromatic Dispersion Monitoring for NRZ-DPSK System Using Asynchronous Amplitude Histogram Evaluation

We propose and demonstrate a chromatic dispersion (CD) monitoring technique for a nonreturn-to-zero differential phase-shift keying (NRZ-DPSK) signal generated with a Mach-Zehnder modulator at 40 Gb/s by analyzing the waveform overshoot after transmission. Without demodulating the NRZ-DPSK signal, the CD up to 120 ps/nm is monitored experimentally via the amplitude of the overshoot. Furthermore, based on the asynchronous amplitude histogram (AAH) evaluation method, a novel histogram processing method, which is more convenient, is proposed and investigated. Experimental results show that the monitoring scheme for CD is independent of optical signal-to-noise ratio (OSNR) within a certain range. This technique needs neither demodulating the signal nor extracting the synchronous clock, and it can be applied to high-order modulation formats at different bit rates.

All-optical multiple-channel logic XOR gate for NRZ-DPSK signals based on nondegenerate four-wave mixing in a silicon waveguide

We report an all-optical multiple-channel exclusive OR (XOR) gate for 10 Gbits/s non-return-to-zero differential phase-shift keying (NRZ-DPSK) signals using nondegenerate four-wave mixing in a silicon waveguide. The function of the logic XOR gate is experimentally demonstrated using 40 bit DPSK sequences. Also, the eye diagram of the XOR signal is clearly observed as the incident signals are both modulated by DPSK sequences originating from 2(31)-1 pseudorandom binary sequences.

All-optical parallel NRZ-DPSK to RZ-DPSK format conversion at 40 Gb/s based on XPM effect in a single SOA

We propose and demonstrate multi-channel parallel format conversions from the non return-to-zero differential phase shift keying (NRZ-DPSK) to the return-to-zero DPSK (RZ-DPSK) using a single semiconductor optical amplifier (SOA). The simultaneous conversions are based on the cross phase modulation (XPM) effect, which is induced by a synchronous optical clock signal with high input power. The XPM adds an identical phase shift onto every input bit, resulting in the phase difference unchanged. The input spectra are broadened and a subsequent filter is utilized to extract the specific part to form a RZ pulse. 6-channel NRZ-DPSK signals at 40 Gb/s can be converted to the corresponding RZ-DPSK signals with ~-0.8 to -1 dB power penalty for all the channels.

Phase-transparent optical data exchange of 40 Gbit/s differential phase-shift keying signals

We report the phase-transparent optical data exchange of differential phase-shift keying (DPSK) signals by exploiting the parametric depletion of nondegenerate four-wave mixing (FWM) in a highly nonlinear fiber. Theoretical analyses of nondegenerate FWM involving two signals and two pumps are presented. Analytical solutions are derived, indicating the exchange condition and the feasibility of phase-transparent data exchange. Optical data exchange between 10.7 Gbit/s non-return-to-zero DPSK (NRZ-DPSK) and return-to-zero DPSK signals is implemented with a power penalty of approximately 1.5 dB at a bit-error rate (BER) of 10(-9). Moreover, we demonstrate phase-transparent optical data exchange between two 40 Gbit/s NRZ-DPSK signals with a power penalty of approximately 4.5 dB at a BER of 10(-9).

NRZ-DPSK and RZ-DPSK Signals Signed Chromatic Dispersion Monitoring Using Asynchronous Delay-Tap Sampling

In this paper, we demonstrated a signed chromatic dispersion (CD) monitoring method of 10 GHz nonreturn-to-zero differential phase-shift keying (NRZ-DPSK) and return-to-zero differential phase-shift keying (RZ-DPSK) signals by using asynchronous delay-tap sampling and an imperfect tuned delay interferometer. This method could monitor not only the value but also the polarity of residual CD. The demodulated signals show amplitude shoulders on the rising edge or the trailing edge with CD accumulation. Delay-tap sampling scatter plots could reflect this signal distortion by a unique characteristic and realize the signed CD monitoring. The monitoring range can be up to plusmn400 and plusmn720 ps/nm for NRZ-DPSK and RZ-DPSK signals, respectively. Simulation and experimental results are also proposed.

All-optical clock extraction from 10-Gbit/s NRZ-DPSK data using modal interference in a two-mode fiber

All-optical clock extraction from a 10-Gbit/s NRZ-DPSK input signal is demonstrated using modal interference in a two-mode fiber (TMF) and a mode-locked fiber ring laser. The TMF has a Mach–Zehnder configuration with two arms along the core and cladding regions. Using the difference in propagation delay between two arms, the non-return-to-zero differential phase shift keying (NRZ-DPSK) signal is converted to the return-to-zero on–off keying (RZ-OOK) signal. To obtain repetitive pulses as a clock signal from the RZ-OOK signal, a ring laser with a semiconductor optical amplifier (SOA) is used. Subsequently, the carrier-to-noise ratio (CNR) of the RZ-OOK and clock signals are enhanced up to 30 dB and 40 dB, respectively, compared to that of the original NRZ-DPSK signal. Also, the clock signal centered at 10 GHz has a low timing jitter of <1.6 ps. It is expected that this method can be applied to high speed fiber-optic systems of >10 Gbit/s due to its small time delay between the core and cladding regions.

Experimental demonstration on 40 Gbit/s all-optical multicasting logic XOR gate for NRZ-DPSK signals using four-wave mixing in highly nonlinear fiber

We propose and demonstrate all-optical multicasting logic XOR gate for non-return-to-zero differential phase-shift keying (NRZ-DPSK) signals by using non-degenerate four-wave mixing (FWM) in a highly nonlinear fiber (HNLF). Theoretical analysis regarding the operation principle of NRZ-DPSK logic XOR gate is clearly described by deriving an analytical solution under the non-depletion approximation. The NRZ-DPSK logic XOR operation is attributed to the linear relationship of complex amplitudes between converted idlers and input NRZ-DPSK signals. By using three non-degenerate FWM processes in an HNLF, 40 Gbit/s all-optical multicasting logic XOR gate for NRZ-DPSK signals are successfully demonstrated in the experiment.

All-optical clock recovery of 20 Gbit/s NRZ-DPSK signals using polarization-maintaining fiber loop mirror filter and semiconductor optical amplifier fiber ring laser

All-optical clock recovery (CR) from 20 Gbit/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signals are demonstrated experimentally by using a polarization-maintaining fiber loop mirror filter (PMF-LMF) and a semiconductor optical amplifier (SOA) fiber ring laser. Only by adjusting polarization controller (PC), NRZ-DPSK signals were conveniently and fast converted to pseudo return-to-zero (PRZ) signal via PMF-LMF. Then the PRZ signals are injected into the SOA fiber laser for CR. The recovered clock signals is with the extinction ratio (ER) of 10 dB and the root-mean-square (RMS) timing jitter of 750 fs in 2 31 − 1 long pseudorandom binary sequence (PRBS) NRZ-DPSK signals measurement. Moreover, the broad wavelength tunability of recovered clock stemmed from the use of SOAs as modulator and the gain medium are shown too.

All-Optical Clock Recovery for 40-Gb/s MZM-Generated NRZ-DPSK Signals Using a Self-Pulsating DBR Laser

All-optical clock recovery for the nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) modulation format is demonstrated experimentally at 40 Gb/s using a self-pulsating distributed Bragg reflector laser. The use of a Mach-Zehnder modulator to generate the NRZ-DPSK signal yields a modulated signal spectrum with a weak clock tone. The self-pulsating laser is able to directly recover a clock signal with a root-mean-square timing jitter of 760 fs and an extinction ratio of 13 dB; a preprocessing stage to enhance the clock tone is not required. The timing jitter of the recovered clock signal is characterized for different values of the input signal optical signal-to-noise ratio and for varying amounts of waveform distortion due to polarization-mode dispersion.

All-Optical Clock Recovery from NRZ-DPSK Signals at Flexible Bit Rates

We propose and demonstrate all-optical clock recovery (CR) from nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signals at different bit rates theoretically and experimentally. By pre-processing with a single optical filter, clock component can be enhanced significantly and thus clock signal can be extracted from the preprocessed signals, by cascading a CR unit with a semiconductor optical amplifier based fibre ring laser. Compared with the previous preprocessing schemes, the single filter is simple and suitable for different bit rates. The clock signals can be achieved with extinction ratio over 10 dB and rms timing jitter of 0.86 and 0.9 at 10 and 20 Gb/s, respectively. The output performances related to the bandwidth and the detuning of the filter are analysed. By simply using a filter with larger bandwidth, much higher operation can be achieved easily.

All-optical NRZ-DPSK clock recovery using linearly chirped fiber Bragg grating induced clock tone

All-optical clock recovery (CR) from 10 Gbps nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signal is experimentally demonstrated, by introducing the chromatic dispersion induced clock tone into a free-running semiconductor optical amplifier (SOA) based fiber ring laser for achieving mode-locking. Since no special component is required for NRZ-DPSK demodulation, our proposed method is very promising because of its simple configuration and better stability. The good performance of our proposed configuration is fulfilled with a linearly chirped fiber Bragg grating (LCFBG) to regenerate clock tone of the NRZ-DPSK signal. The recovered clock signal with the extinction ratio of 17 dB and the root-mean-square timing jitter of 540 fs is achieved under 2 31 − 1 pseudorandom binary sequence NRZ-DPSK signals measurement. Due to the same operation principle, our configuration has the potential to implement all-optical CR for NRZ-DPSK signal with data rate up to 40 Gbps.

All-Optical NRZ-DPSK Clock Recovery Using Chromatic-Dispersion-Induced Clock Tone

All-optical clock recovery (CR) from 10-Gb/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signal is demonstrated experimentally by introducing the chromatic-dispersion-induced clock tone into a free-running semiconductor optical amplifier (SOA)-based fiber ring laser for achieving mode-locking. Since no special component is required for NRZ-DPSK demodulation, our proposed method is very promising because of its simple configuration and better stability. The good performance of our proposed configuration is fulfilled with a 20-km standard single-mode fiber to regenerate clock tone of the NRZ-DPSK signal. The recovered clock signal with the extinction ratio of 17 dB and the root-mean-square timing jitter of 718 fs is achieved under 231-1 pseudorandom binary sequence NRZ-DPSK signals measurement

All-Optical Clock Recovery From NRZ-DPSK Signal

All-optical clock recovery (CR) from 20-Gb/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signal is demonstrated, with an all-fiber delay interferometer (DI) and a mode-locked semiconductor optical amplifier (SOA) fiber laser. The tunable DI serves as an all-optical DPSK demodulator and the phase-modulated NRZ-DPSK signal is converted into the intensity-modulated pseudoreturn-to-zero (PRZ) signal, with the enhancement of the clock component. Followed SOA fiber-laser is used to achieve CR from the PRZ signal. Fixed bit pattern and 2 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">31</sup> -1 pseudorandom binary sequence NRZ-DPSK signals are used to test the performance of the proposed system. It is shown that the recovered clock signal with the extinction ratio over 10 dB and the root-mean-square timing jitter of 800 fs can be achieved