Non-thermal Air Plasma Research Articles

Effect of Humidity on the Inactivation of Bacillus Subtilis Spore by Non-thermal Atmospheric Air Plasma

Objective: If a medical device is not properly disinfected, it will pose a potential danger to patients. Spore is an experimental strain to verify the effect of disinfection on medical devices. It has a complex structure and is somewhat resistant to conventional disinfection techniques. Based on the advantages of simple structure and abundant reactive oxygen and nitrogen species (RONS), surface dielectric barrier discharge (SDBD) has been used to deal with inactivate spores, which provided experimental support for the application of sterilization spores in medical devices. Methods: The sterilization efficiency of the plasma was evaluated by calculating the number of viable colonies on Tryptose Soya Agar. RONS including ozone, nitrogen oxides and other reactive species produced in SDBD were measured by ozone analyzer, Fourier infrared spectrometer and chemical probes, respectively. Ultraviolet-visible spectrophotometer was used to determine the concentration of protein and nucleic acid. Results: After 20min of SDBD treatment, the number of inactivated spores could reach more than 4 log at high humidity (>6g/m3), while the spores were hardly inactivated at low humidity (<6g/m3). Ozone production was inhibited with increasing humidity while OH radicals and peroxynitrous acid increased with increasing humidity. The optical density values of protein and nucleic acid released from spores treated with SDBD was detected and a strong correlation was found with the spore inactivation trend. The protein shell and membrane structure of the spores were destroyed by SDBD, and more leakage and destruction of proteins and nucleic acids in the spores were obtained under the high humidity. Conclusion: With the increase of air humidity (from 0.15g/m3 to 70.16g/m3), stable SDBD is obtained showing a typical filamentous discharge pattern. Compared with low humidity, high humidity is more favorable to SDBD inactivation of spores.

Experimental Study on the Degradation of Acaricides on the Surface of Kumquat Cuimi by Nonthermal Air Plasma

Nonthermal air plasma, which can be generated by air discharge, contains large amounts of reactive oxygen species (ROS), reactive nitrogen species (RNS) and high-energy particles. The ROS and RNS have strong oxidizing properties, and the high-energy particles can break chemical bonds in organic compounds, a process which can be used to degrade organic matter such as pesticides. In the present study, the effects of nonthermal air plasma on the degradation of several pesticides were investigated. An air plasma processing system was designed and constructed to produce nonthermal air plasma and to degrade five commonly used acaricides, namely, avermectin, bifenazate, spirodiclofen, etoxazole, and lufenuron, during the production of kumquat cuimi. The experimental results showed that nonthermal air plasma could degrade all the acaricides on the surface of the kumquat cuimi effectively. After 20 min of plasma treatment, the residues of avermectin, bifenazate, spirodiclofen, etoxazole and lufenuron on the surface of the kumquat cuimi were reduced by 80.67%, 79.52%, 62.40%, 48.93% and 23.11%, respectively. Further analysis indicated that the primary chemical bonds, hydrophobicity, and the pH value of the plasma-activated water can all affect the efficiency of pesticide degradation.

Selective Cytotoxicity of Lung Cancer Cells—A549 and H1299—Induced by Ringer's Lactate Solution Activated by a Non-thermal Air Plasma Jet Device, Nightingale®

Selective Cytotoxicity of Lung Cancer Cells—A549 and H1299—Induced by Ringer's Lactate Solution Activated by a Non-thermal Air Plasma Jet Device, Nightingale®

Physicochemical Characteristics of Pork Liver Pâtés Containing Nonthermal Air Plasma-Treated Egg White as an Alternative Source of Nitrite

The use of nonthermal air plasma is rapidly becoming a novel technology as an alternative source of nitrites in the meat industry. As egg white is a versatile and cost-effective ingredient commonly used to improve the texture of meat products, the effect of its addition after plasma treatment (PTEW) on the yield, pH, residual nitrite, nitrosyl hemochrome, TBARS, color, texture parameters, and aroma profile of pork liver pâtés was studied. The nitrite ion content of plasma-activated egg whites was adjusted to the positive controls containing 60 ppm (PC1) and 120 ppm (PC2) sodium nitrite by modifying the duration of their plasma treatment (PTEW1 and PTEW2, respectively). A group without the addition of nitrites was also manufactured (NC). Each treatment (NC, PC1, PC2, PTEW1, PTEW2) was analyzed on days 1, 3, 5, and 7 of storage at 4 °C. The results showed that liver pâtés containing plasma-treated egg whites had a similar nitrite and nitrosyl hemochrome content compared to samples containing the same amount of nitrite ions derived from sodium nitrite (p ≥ 0.05). In addition, 40 ppm nitrite ions, regardless of the source, was sufficient to achieve the desired reddish-pink color of the product over the entire storage period. Both nitrites from sodium nitrite and plasma-treated egg whites also significantly reduced lipid oxidation compared to the NC group (between 10% and 23% reduction on the last day), but had no significant effect on yield, pH, and texture parameters of the products. Based on the principal component analysis (PCA), the aroma profile of pâtés differed significantly between the groups with and without nitrites, with the largest differences observed on the first day (approx. 88%). Importantly, PTEW1 and PTEW2 aroma after production was similar to group PC2. The results of our study suggest that plasma-activated egg whites can be used as a potential source of nitrite in liver pâté production without adversely affecting the technological properties and shelf life of the final product.

Quality of Tomato Juice as Influenced by Non-Thermal Air Plasma Treatment

This paper presents the results of an experiment based on using a Glide-arc type plasma reactor operating at atmospheric pressure for the quality of fresh pressed tomato juice, variety Bekas. The impact of after-glow plasma gas (air) on the physicochemical, microbiological properties and morphology of the product’s samples was investigated. Five groups of juices characterized by different exposure times (30, 60, 120, 300 and 600 s), as well as untreated juice (as control) were used. The juice quality was assessed on days 1, 3, 5, and 10 of refrigerated storage. Significant increases were observed when Cold Atmospheric Plasma (CAP)-treated tomato juice was tested against total soluble solids, pH, lycopene, and vitamin C in comparison to the control treatments. Moreover, changes in the tested physicochemical values during the storage of juice subjected to the action of cold plasma did not progress as quickly as in the case of the control juice. A significant decrease was observed in total plate count, yeast, and mold after 300–600 s CAP treatment. The findings of the current study suggested that CAP treatment is a promising technique that could provide improved quality and stability during the processing of tomato juice with better physicochemical properties and bioavailable nutrients.

Clindamycin removal from aqueous solution by non-thermal air plasma treatment: performance, degradation pathway and ensuing antimicrobial activity.

The present study set out to investigate clindamycin (CLN) removal from aqueous solution using non-thermal plasma (NTP) under atmospheric air conditions and to address the effects of some variables including pH, initial concentration of CLN, and working voltage on CLN degradation. The result showed that the NTP system exhibited excellent degradation rate and mineralization efficiency on CLN in 15 min under neutral conditions, which exceeded 90 and 45%, respectively, demonstrating its conversion to other organic by-products. Furthermore, CLN degradation was largely dependent upon the initial pH of solution, applied voltage, and reaction time. Specifically, under acidic conditions (pH = 3), working voltage of 24 kV and after 15 min of reaction, almost 100% of CLN was degraded. NTP-initiated CLN degradation products through LC-MS/MS analysis, determined within 10 min of reaction, inferred that the complex structure of CLN has undergone deterioration by active radical species which subsequently generated small molecular organic compounds. Chemical processes involved in CLN degradation were found to be demethylation, desulfonylation, dechlorination, hydroxylation and deamination. Lastly, antimicrobial susceptibility tests revealed that the activity of CLN was reduced following NTP treatment, which is also in good agreement with the minimum inhibitory concentration (MIC) values obtained from microdilution analyses.

Streamer propagation in humid air

We investigate the effect of humidity on the propagation of streamers in air. We present a minimal set of chemical reactions that takes into account the presence of water in a nonthermal air plasma and considers ionization, attachment, detachment, recombination and ion conversion including water cluster formation. We find differences in streamer propagation between dry and humid air that we attribute mostly to an enhanced effective attachment rate in humid air, leading to higher breakdown electric field and threshold field for propagation. This higher effective attachment rate in humid conditions leads to a faster decay of the conductivity in the streamer channel, which hinders the accumulation of charge in the streamer head. In some cases a propagating streamer solution still exists at the expense of a smaller radius and lower velocity. In other cases a high humidity leads to the stagnation of the streamer. We finally discuss how all these statements may affect streamer branching and the dimensions and lifetime of a streamer corona.

Enhancement of Lettuce Growth by PAW Spray Gliding Arc Plasma Generator

The effect of non-thermal air plasma on green oak lettuce farming has been proposed. A gliding arc plasma generator (GAPG) was designed for plasma-activated water (PAW) spray generation. A PAW spray was generated at 8, 10, and 12 kV by a custom-made ac high voltage power supply. Four hydroponic green oak lettuce trays were treated by PAW spray at different conditions for 10 min, three times a day for nine days. The experimental results showed that all the plasma-treated green oak lettuce sprouts had a greater growth rate than the control group. The best condition was found in the PAW spray generated at 8 kV source voltage, which led to the longest average height and width of sprouts of 10.88 ± 0.33 cm and 10.09 ± 0.08 cm, respectively. Moreover, its average dried weight was also significantly greater than that of the control group by 1.69 times. It was found that the concentration of total Kjeldahl nitrogen (TKN), mainly ammonium, was enhanced in every PAW spray condition. However, the highest TKN concentration was found in the 8 kV PAW spray, which was 3.67 times higher than that of the control group. The amount of nitrite (NO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−</sup> ) and nitrate (NO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−</sup> ) in PAW spray was also enhanced but in the opposite trend to TKN concentration. Moreover, the electrical conductivity (EC) and pH levels could be improved by air plasma. It could be confirmed that the plasma treatment could be effectively applied to green oak lettuce farming, and the PAW spray generated by the GAPG could enhance the amount of nitrogenous fertilizer in treated water, which is essential for plant growth stimulation.

Influence of Air Plasma Pretreatments on Mechanical Properties in Metal-Reinforced Laminated Wood

The use of wood-based materials in building and construction is constantly increasing as environmental aspects and sustainability gain importance. For structural applications, however, there are many examples where hybrid material systems are needed to fulfil the specific mechanical requirements of the individual application. In particular, metal reinforcements are a common solution to enhance the mechanical properties of a wooden structural element. Metal-reinforced wood components further help to reduce cross-sectional sizes of load-bearing structures, improve the attachment of masonry or other materials, enhance the seismic safety and tremor dissipation capacity, as well as the durability of the structural elements in highly humid environments and under high permanent mechanical load. A critical factor to achieve these benefits, however, is the mechanical joint between the different material classes, namely the wood and metal parts. Currently, this joint is formed using epoxy or polyurethane (PU) adhesives, the former yielding highest mechanical strengths, whereas the latter presents a compromise between mechanical and economical constraints. Regarding sustainability and economic viability, the utilization of different adhesive systems would be preferable, whereas mechanical stabilities yielded for metal-wood joints do not permit for the use of other common adhesive systems in such structural applications. This study extends previous research on the use of non-thermal air plasma pretreatments for the formation of wood-metal joints. The plasma treatments of Norway spruce [Picea abies (L.) Karst.] wood and anodized (E6/EV1) aluminum AlMgSi0.5 (6060) F22 were optimized, using water contact angle measurements to determine the effect and homogeneity of plasma treatments. The adhesive bond strengths of plasma-pretreated and untreated specimens were tested with commercial 2-component epoxy, PU, melamine-urea formaldehyde (MUF), polyvinyl acetate (PVAc), and construction adhesive glue systems. The influence of plasma treatments on the mechanical performance of the compounds was evaluated for one selected glue system via bending strength tests. The impact of the hybrid interface between metal and wood was isolated for the tests by using five-layer laminates from three wood lamellae enclosing two aluminum plates, thereby excluding the influence of congeneric wood-wood bonds. The effect of the plasma treatments is discussed based on the chemical and physical modifications of the substrates and the respective interaction mechanisms with the glue systems.

Strength and flexibility of lithium disilicate bonded to polyetherketoneketone

Statement of problemPolyetherketoneketone (PEKK) is a high-performance polymer gaining popularity in dentistry for the fabrication of crowns, fixed partial dentures, removable partial denture frameworks, and frameworks for implant-supported fixed complete dentures. Despite a lack of performance data, lithium disilicate crowns have been bonded to retentive elements in PEKK frameworks. PurposeThe purpose of this in vitro study was to compare the bond strengths and flexibility of lithium disilicate to PEKK or zirconia. Material and methodsForty-five PEKK, 15 zirconia, and 60 lithium disilicate beam-shaped specimens (12.5×2×2 mm) were fabricated. The ends of the PEKK beams were subjected to 3 different surface treatments before the application and light polymerization of a primer: 50-μm aluminum oxide airborne-particle abrasion, nonthermal air plasma, and argon-oxygen plasma. The zirconia specimen bonding surfaces were prepared with 50-μm aluminum oxide airborne-particle abrasion and the application of primer. Lithium disilicate specimens were etched with 4.5% hydrofluoric acid, and primer was applied. The lithium disilicate specimens were luted with an adhesive resin cement to the PEKK and zirconia specimens by using light-activated and chemically activated polymerization. Fifteen monolithic specimens of PEKK, lithium disilicate, and zirconia (25×2×2 mm) were also fabricated. All specimens were incubated overnight in 100% humidity before testing. Bonded and monolithic specimens were loaded in a universal testing machine, and 4-point bend tests were conducted until failure (n=15). The flexural modulus and strength were calculated and statistically analyzed with 1-way analysis of variance and Student-Newman-Keuls post hoc tests (α=.05). ResultsAll bonded specimens failed at the adhesive interface. The zirconia-lithium disilicate bond strength was approximately twice that of the strongest group of PEKK (airborne-particle abrasion group) bonded to lithium disilicate (42 ±12 MPa and 24 ±13 MPa, respectively) and was approximately 9 times more rigid (71 ±19 GPa and 8 ±2 GPa, respectively). Monolithic PEKK fractured at 238 ±22 MPa, monolithic zirconia at 771 ±128 MPa, and monolithic lithium disilicate at 173 ±26 MPa. Monolithic PEKK was approximately 30 times more flexible than monolithic zirconia (6 ±1 GPa and 178 ±16 GPa, respectively). All values were statistically significantly different (P<.05), except for the bond strength between lithium disilicate and PEKK treated with airborne-particle abrasion and nonthermal air plasma and the flexural moduli of PEKK to lithium disilicate. ConclusionsBond strength between PEKK and lithium disilicate was significantly weaker than that between zirconia and lithium disilicate. Monolithic PEKK was significantly more flexible than monolithic zirconia.

Shelf life prolongation of fresh strawberries by nonthermal plasma treatment

The action of nonthermal atmospheric air plasma, producing the rich amount of reactive particles from surrounding air, on strawberries microbial decontamination was investigated. The plasma produced by the multipoint AC corona discharge fed by a Tesla coil and applied on strawberries leads to a substantial reduction of microbial load without influencing the sensory properties like taste and color. After the plasma treatment, the strawberries stored in conditions similar to the store remained healthy in appearance for up to 4 days longer. Although the number of healthy untreated strawberries decreased in 1 day under 80%, the number of treated ones remained over 80% up to 4 days of storage. Novelty impact statement Plasma treatment significantly reduced the microbial contamination of strawberries. Plasma significantly prolonged the shelf life of strawberries. Plasma neither influenced the sensory properties nor the color of exposed strawberries.

Reaction of the N Atom with Electronically Excited O2 Revisited: A Theoretical Study

The kinetics of the reaction of N with electronically excited O2 (singlet a1Δg and b1Σg+ states), potentially relevant for NOx formation in nonthermal air plasma, is theoretically studied using the multireference second-order perturbation theory. The corresponding thermodynamically and kinetically favored reaction pathways together with possible intersystem crossings are identified. It has been revealed that the energy barrier for the N + O2(a1Δg) → NO + O reaction is approximately twice the barrier height for the counterpart process with O2(X3Σg-). The molecular oxygen in the b1Σg+ state, in turn, proved to be even less reactive to atomic nitrogen than O2(a1Δg). Appropriate thermal rate constants for specified reaction channels are calculated by the variational transition-state theory incorporating corrections for the tunneling effect, nonadiabatic transitions, and anharmonicity of vibrations for transition states and reactants. The corresponding three-parameter Arrhenius expressions for the broad temperature range (T = 300-4000 K) are reported. At last, post-transition-state molecular dynamics simulations indicate that the N + O2(a1Δg) reaction produces vibrationally much colder NO molecules than the N + O2(X3Σg-) process.

Air Plasma Mitigation of Shock Wave

Theory is presented to show that shock wave structure can be modified via interacting with an air plasma plume generated symmetrically in front of a shock wave generator. Electron jet in the plasma plume deflects the impinging airflow via momentum transfer collisions. Symmetrical deflection makes it easy to satisfy the conservation of transverse momentum between the airflow and plasma. The charge transfer between N2+ and N2 randomizes the impinging airflow to increase the deflection angle. The flow deflection increases the effective cone angle of the shock generator; as the effective cone angle exceeds a critical value, the shock becomes detached and faded.&nbsp; Experiments were conducted in a Mach 2.5 wind tunnel to mitigate shock wave via air plasma deflection. A non-thermal air plasma was symmetrically generated, in front of a wind tunnel model by on-board 60 Hz periodic electric arc discharge, as a deflector for shock wave mitigation. The results show a transformation of the shock from a well-defined attached shock into a highly curved shock structure, which has increased shock angle and appears in diffused form. Shown in a sequence with increasing discharge intensity, the transformed curve shock in front of the model moves upstream to become detached with increasing standoff distance from the model and is eliminated when the discharge is near the peak. The steady of the incoming flow during the discharge cycle is manifested by the repetition of the baseline shock front. The experimental observations confirm the theory and efficacy of this air plasma mitigator.

The effect of water activated by nonthermal air plasma on the growth of farm plants: Case of maize and barley

AbstractThe effects of plasma‐activated water (PAW) generated by nonthermal air plasmas of transient spark with water electrospray or atmospheric glow discharge were investigated on maize (Zea mays L. var Saccharata) and barley (Hordeum vulgare L.) seedlings. PAW is characterized by measuring concentrations of reactive oxygen and nitrogen species (H2O2, , ). After 4 weeks of plants growth, the effects of PAW are analyzed by measuring plant growth and physiological parameters: plant length and fresh weight, photosynthetic pigments concentration and photosynthesis rate, total soluble proteins, antioxidant enzyme activity, and DNA damage. The results suggest that PAW, depending on chemical composition, has the potential to improve the plant growth and influence the physiological parameters, while causing no harmful DNA damage.

Measurement of nitrogen dioxide and nitric oxide densities by using CEAS (cavity‐enhanced absorption spectroscopy) in nonthermal atmospheric pressure air plasma

AbstractNonthermal atmospheric pressure plasmas are widely used in biomedicine and agriculture. Currently, radical density is used as an important parameter for the development of plasma biomedicine and agriculture. Especially, nitrogen dioxide (NO2) and nitric oxide (NO) radicals are significant species in these applications. These could be measured by using the cavity‐enhanced absorption spectroscopy (CEAS) technique. For the NO2 and NO radical density measurement, we used a visible LED (light‐emitting diode) of 660 nm and a mid‐infrared LD (laser diode) of 5238.6 nm, respectively. Radical densities can be calculated with the transmission ratio using Beer–Lambert law, which is obtained by the absorbed amount of laser intensity passed through the gas from the plasma jet in an optical cavity of CEAS.

Influence of Nonthermal Atmospheric Plasma-Activated Water on the Structural, Optical, and Biological Properties of Aspergillus brasiliensis Spores

Plasma-activated water (PAW) has emerged as a platform for sterilizing fungal pathogens. In this study, we investigated the influence of PAW on black melanized spores of Aspergillus brasiliensis to explore the mechanism of fungal spore inactivation. PAW was prepared by activating deionized water with a nonthermal atmospheric pressure air plasma jet (soft plasma jet). The concentrations of H2O2 and NOx in the PAW treated by the soft plasma jet for 3 min were 50 μM and 1.8 mM, respectively, and the pH of the PAW was 3.10. The reactive oxygen and nitrogen species (RONS) in the PAW increased with longer plasma activation time. After being treated for 30 min in the PAW with a plasma activation time of 3 min, the spore viability dramatically dropped to 15%. The viabilities of 0.3% H2O2- and 0.3% HNO3-treated spores were 22% and 42%, respectively. The breakage of the spore cell wall by the PAW was revealed in scanning electron microscope images and flow cytometry measurements. Disruption of cell wall integrity provides a path for intracellular components to escape and RONS of the PAW can attack intracellular components directly. Degradation of high molecular genomic DNA was also observed by agarose gel electrophoresis. These results suggest that long-lived reactive species generated in the PAW play an important role in the inactivation of melanized fungal spores. Consequently, PAW produced by a soft plasma jet can be applied to sterilize bioprotective walled fungal spores in a relatively large volume.

Surface modification of fly ash by non-thermal air plasma for elemental mercury removal from coal-fired flue gas

ABSTRACT The fly ash from a coal-fired power plants was modified with non-thermal plasma in air to improve the elemental mercury (Hg0) removal performance. The Hg0 adsorption experiments were implemented via a bench-scale fixed-bed reactor system. Brunauer–Emmett–Teller (BET), X-ray photoelectron spectroscopy (XPS), ultimate, X-ray diffraction (XRD) and XRF analysis were employed to characterize the fly ash. The effect of non-thermal plasma voltage and time on Hg0 removal efficiency was investigated. The results showed that fly ash had better Hg0 removal performance when treatment voltage was 3.0 kV and treatment time was 7 min. Furthermore, the results showed that non-thermal plasma treatment had little influence on the specific surface area. However, non-thermal plasma treatment increased the relative content of oxygen. XPS and temperature programmed desorption results indicated that Hg0 removal process included adsorption and oxidation of Hg0. Moreover, ester and carbonyl groups played extremely vital roles in the improvement of Hg0 removal performance, and their temperature programmed desorption peak occurred at around 250°C and 320°C, respectively.

Reduction of phoxim pesticide residues from grapes by atmospheric pressure non-thermal air plasma activated water.

In this study, we propose a novel strategy, plasma activated water (PAW) to reduce pesticide residues on agricultural products. To validate its feasibility and effectiveness, we employee high-performance liquid chromatography (HPLC) to detect phoxim on grapes. HPLC results suggest that the reduction of phoxim on grapes achieve 73.60% after treated 10 min by PAW prepared 30 min, and the concentration of phoxim decreased significantly (p < 0.05) with the preparation time of PAW. Furthermore, HPLC-MS analysis shows that the reduction effect of phoxim by PAW is dominated by the degradation of phoxim. Combined with analyzing the physicochemical properties of PAW, one possible degradation pathway is proposed under the present experimental conditions, mediated by reactive oxygen and nitrogen species. The acidic environment (pH < 3) and high oxidation capacity (ORP > 500 mV) are suggested to be a benefit to the reduction of phoxim. Besides, the experimental results regarding color, firmness, sugar, vitamin C, and superoxide dismutase of grapes demonstrate that the PAW treatment will not significantly affect the quality of grapes. In conclusion, phoxim pesticide residues on grapes could be effectively reduced by the PAW strategy and without a significant (p < 0.05) effect on grapes quality.

Singlet oxygen generated by a new nonthermal atmospheric pressure air plasma device exerts a bactericidal effect on oral pathogens.

Oral diseases generally have certain bacteria associated with them. Non-thermal atmospheric pressure plasma (NTAP), generated at atmospheric pressure and room temperature, incorporates several molecules, including reactive oxygen species, that can inactivate various bacteria including oral pathogens. For this reason, several NTAP devices have been developed to treat oral diseases. Use of noble gases can enhance the bactericidal efficacy of NTAP, but this requires additional gas supply equipment. Therefore, a new NTAP device that employs ambient air as the working gas was developed. The device generates non-thermal atmospheric pressure air plasma. Here, the singlet oxygen (1O2) levels generated, their bactericidal effects on oral pathogens (Streptococcus mutans, Porphyromonas gingivalis, and Enterococcus faecalis), and the bacterial oxidative stress they imposed were measured. 1O2 generation in phosphatebuffered saline was assessed qualitatively using electron spin resonance (ESR) spectroscopy, and bactericidal efficacy was evaluated by counting of colony-forming units/mL. Bacterial oxidative stress was determined by measurement of hydrogen peroxide (H2O2) and superoxide dismutase (SOD) activity. ESR indicated that the level of 1O2 increased significantly and time-dependently, and was inversely correlated with distance, but the bactericidal effects were correlated only with treatment time (not distance) as H2O2 increased and SOD levels decreased, suggesting that the new device has potential applicability for treatment of oral disease.

Removal of dimethyl phthalate in water by non-thermal air plasma treatment

In this study, the effect of a non-thermal microplasma array on the degradation of dimethyl phthalate (DMP) solution was investigated using a high pressure liquid chromatograph and mass spectrometer (LC-MS).