Molecule Non-fullerene Acceptors Research Articles

Tuning Surface Defect States in Sputtered Titanium Oxide Electron Transport Layers for Enhanced Stability of Organic Photovoltaics.

Nonfullerene acceptors (NFAs) have dramatically improved the power conversion efficiency (PCE) of organic photovoltaics (OPV) in recent years; however, their device stability currently remains a bottleneck for further technological progress. Photocatalytic decomposition of nonfullerene acceptor molecules at metal oxide electron transport layer (ETL) interfaces has in several recent reports been demonstrated as one of the main degradation mechanisms for these high-performing OPV devices. While some routes for mitigating such degradation effects have been proposed, e.g., through a second layer integrated on the ETL surface, no clear strategy that complies with device scale-up and application requirements has been presented to date. In this work, it is demonstrated that the development of sputtered titanium oxide layers as ETLs in nonfullerene acceptor based OPV can lead to significantly enhanced device lifetimes. This is achieved by tuning the concentration of defect states at the oxide surface, via the reactive sputtering process, to mitigate the photocatalytic decomposition of NFA molecules at the metal oxide interlayers. Reduced defect state formation at the oxide surface is confirmed through X-ray photoelectron spectroscopy (XPS) studies, while the reduced photocatalytic decomposition of nonfullerene acceptor molecules is confirmed via optical spectroscopy investigations. The PBDB-T:ITIC organic solar cells show power conversion efficiencies of around 10% and significantly enhanced photostability. This is achieved through a reactive sputtering process that is fully scalable and industry compatible.

CPE-Na-Based Hole Transport Layers for Improving the Stability in Nonfullerene Organic Solar Cells: A Comprehensive Study.

Organic photovoltaic (OPV) cells have experienced significant development in the last decades after the introduction of nonfullerene acceptor molecules with top power conversion efficiencies reported over 19% and considerable versatility, for example, with application in transparent/semitransparent and flexible photovoltaics. Yet, the optimization of the operational stability continues to be a challenge. This study presents a comprehensive investigation of the use of a conjugated polyelectrolyte polymer (CPE-Na) as a hole layer (HTL) to improve the performance and longevity of OPV cells. Two different fabrication approaches were adopted: integrating CPE-Na with PEDOT:PSS to create a composite HTL and using CPE-Na as a stand-alone bilayer deposited beneath PEDOT:PSS on the ITO substrate. These configurations were compared against a reference device employing PEDOT:PSS alone, as the HTL increased efficiency and fill factor. The instruments with CPE-Na also demonstrated increased stability in the dark and under simulated operational conditions. Device-based PEDOT:PSS as an HTL reached T80 after 2500 h while involving CPE-Na in the device kept at T90 in the same period, evidenced by a reduced degradation rate. Furthermore, the impedance spectroscopy and photoinduced transient methods suggest optimized charge transfer and reduced charge carrier recombination. These findings collectively highlight the potential of CPE-Na as a HTL optimizer material for nonfluorine OPV cells.

Approach toward Low Energy Loss in Symmetrical Nonfullerene Acceptor Molecules Inspired by Insertion of Different π-Spacers for Developing Efficient Organic Solar Cells.

In this quantum approach, by adding bridge/π-spacer fragments between the donor and acceptor parts of a newly constructed DF-PCIC (A-D-A type) molecule, it is the aim to improve the photovoltaic characteristics of organic solar cells (OSCs). After π-spacer insertion into the reference molecule (DF-R), six new molecules (DF-M1 to DF-M6) were designed. The optoelectronic attributes of newly inspected molecules were theoretically calculated using MPW1PW91/6-31G(d,p) level of theory. All newly proposed molecules possessed a lower band gap (Eg), a higher value of absorption, lower reorganization energy, greater dipole moment, and lower energies of excitations than the DF-R molecule. The frontier molecular orbital study proclaimed that the DF-M1 molecule has the lowest band gap of 1.62 eV in comparison to the 2.41 eV value of DF-R. Absorption properties represented that DF-M1 and DF-M2 molecules show the highest absorption values of up to 1006 and 1004 nm, respectively, in the near-infrared region. Regarding the reorganization energy, DF-M2 has the lowest value of λe (0.0683896 eV) and the lowest value of λh (0.1566471 eV). DF-M2 and DF-M5 manifested greater dipole moments with the values of 5.514665 and 7.143434 D, respectively. The open circuit voltage (VOC) of all the acceptors was calculated with J61, a donor complex. DF-M4 and DF-M6 molecules showed higher values of VOC and fill factor than the DF-R molecule. Based on the given results, it was supposed that all the newly presented molecules might prove themselves to be better than the reference and thus might be of great interest to experimentalists. Thus, they are suggested to be used to develop proficient OSC devices with improved photovoltaic prospects in the near future.

Theoretical designing of symmetrical non-fullerene acceptor molecules by end-capped modification for promising photovoltaic properties of organic solar cells

Non-fullerene small molecules must absorb in a broader wavelength range for achieving high efficiencies. This work presents seven indacenodithiophene core-based acceptor molecules (SJA1-SJA7) designed by structurally tailoring the pre-existed SJ-IC molecule. Detailed studies of these newly designed molecules were carried out to analyze the stabilization of energy levels, planarity, UV–Visible absorption, light-harvesting efficiency, open circuit voltage (Voc), and other photovoltaic properties. Structural modification with different acceptors resulted in the narrowing of band gap and broader absorption spectrum. All the newly reported molecules showed significant redshift having λmax values ranging from 686 nm to 722 nm in the gas phase and 742 nm to 792 nm in chloroform as compared to SJ-IC which has λmax values at 675 nm and 732 nm in gas and chloroform medium respectively. Moreover, newly presented molecules exhibited lower excitation energy values and higher oscillator strength than SJ-IC molecule which indicate effective charge transfer between frontier molecular orbitals. Improved charge mobilities were observed as newly developed molecules possessed lower internal reorganization energies. These findings were further confirmed by molecular electrostatic potential (MEP) and transition density matrix (TDM) analysis. In case of Voc, SJA7 emerged as a more proficient molecule due to its higher value (1.440 eV) than SJ-IC (1.42 eV). These results assure the remarkable improvement in optoelectronic properties of designed molecules which makes them a better choice than pre-existing SJ-IC molecule for the development of improved OSCs in the future.

Quantum Modification of Indacenodithieno[3,2-b]thiophene-Based Non-fullerene Acceptor Molecules for Organic Solar Cells of High Efficiency.

In order to enhance the efficacy of organic solar cells, six new three-dimensional small donor molecules (IT-SM1 to IT-SM6) have been computationally designed by modifying the peripheral acceptors of the reference molecule (IT-SMR). The frontier molecular orbitals revealed that IT-SM2 to IT-SM5 had a smaller band gap (Egap) than IT-SMR. They also had smaller excitation energies (Ex) and exhibited a bathochromic shift in their absorption maxima (λmax) when compared to IT-SMR. In both the gas and chloroform phases, IT-SM2 had the largest dipole moment. IT-SM2 also had the best electron mobility, while IT-SM6 had the best hole mobility owing to their smallest reorganization energy for electron (0.1127 eV) and hole (0.0907 eV) mobility, respectively. The analyzed donor molecules' open-circuit voltage (VOC) indicated that all of these proposed molecules had greater VOC and fill factor (FF) values than the IT-SMR molecule. In accordance with the evidence of this work, the altered molecules can seem to be quite proficient for usage by experimentalists and have prospective use in future in the manufacture of organic solar cells with improved photovoltaic properties.

Interfacial Hole-Charge-Transfer Dynamics in Organic Solar Cells: A Dynamic Viewpoint

The energy loss of hole-charge transfer in nonfullerene-acceptor (NFA) organic solar cells has been significantly reduced by minimizing their interfacial energy offset to near-zero and negative values. However, the physical mechanism of highly efficient hole-charge transfer in these conditions has not been fully addressed. In this work, we theoretically clarify that a moving hole charge along the polymer-donor and NFA interface, generated from the spontaneous dissociation of NFA molecular excited states, tends to transfer from NFA molecules to polymer-donor to keep moving, even their interfacial energy offset is chosen as a negative value. This dynamic viewpoint revises the conventional static viewpoint about the dependence of hole-charge transfer upon the interfacial energy offset. In addition, considering the polaron effect in organic molecules with a hole charge generated, we redefine the interfacial energy offset and further consider the effects of the NFA molecular electron-lattice interaction and lattice elastic constant on the hole-charge transfer.

Development of polymeric blue prosthetic retina photoreceptors

Two conjugated polymers with absorption spectra like that of human short-wavelength photoreceptors, or blue cones, are characterised to act as essential components of a sub-retinal flexible prototype prothesis for people suffering from retinal disease affecting photoreceptor cells. Spectrophotometric and transient tests undertaken in unbiased photovoltaic mode in ambient conditions demonstrate that the addition of hole-blocking ZnO layer results in reliably forcing a favourable capacitive charging regime and acts to improve the photoresponse over ten times in one polymer and 45 times in another. We report that the addition of fullerene and non-fullerene acceptor molecules in bulk-heterojunction (BHJ)-active layers make an almost sevenfold measured improvement to extracellular photovoltage for devices operating in an electrolyte environment.Graphical abstract

Polaritons in a Polycrystalline Layer of Non-fullerene Acceptor.

Non-fullerene acceptor molecules developed for organic solar cells feature a very intense absorption band in the near-infrared. In the solid phase, the strong interaction between light and the transition dipole moment for molecular excitation should induce formation of polaritons. The reflection spectra for polycrystalline films of a non-fullerene acceptor with a thienothienopyrrolo-thienothienoindole core of the so-called Y6 type indeed show a signature of polaritons. A local minimum in the middle of the reflection band is associated with the allowed molecular transition. The minimum in reflection allows efficient entry of light into the solid, resulting in a local maximum in external quantum efficiency of a photovoltaic cell made of the pure acceptor.

Role of Exciton Lifetime, Energetic Offsets, and Disorder in Voltage Loss of Bulk Heterojunction Organic Solar Cells

Recently, the power conversion efficiency (PCE) of organic solar cells (OSCs) has significantly progressed with a rapid increase from 10 to 19% due to state-of-the-art research on nonfullerene acceptor molecules and various device processing strategies. However, OSCs still exhibit significant open circuit voltage loss (ΔVOC ∼ 0.6 V) due to high energetic offsets and molecular disorder. In this work, we present a systematic investigation to determine the effects of energetic offset and disorder on different recombination losses in open circuit voltage (VOC) using 13 different photoactive layers, wherein the PCE and ΔVOC vary in the ranges of 2.21-14.74% and 0.561-1.443 V, respectively. The detailed voltage loss analysis of all these devices was carried out, and voltage losses were correlated with energetic offset and disorder. This has enabled us to identify the key features for minimizing the voltage loss like: (1) a low energy offset between the donor and acceptor molecular states is essential to attain a nonradiative voltage loss (ΔVOC,nrad) as low as ∼200 meV and (2) Urbach energy, which is a measure of the materials' disorder and packing, should be low for the minimization of the radiative voltage loss (ΔVOC,rad). In addition, time-resolved photoluminescence spectroscopy was employed to further understand the exciton dynamics of pristine materials and donor-acceptor blends. It was observed that the absorbers with ultralong exciton lifetime (∼1000 ps) produce higher efficiencies. The current study emphasizes the importance of simultaneously testing photovoltaic performance and active layer exciton dynamics for rational device optimization and opens new prospects for designing novel molecules with fine-tuning of energetic offset and disorder with longer exciton lifetime which is the effective strategy to boost the efficiency of OSCs to their modified Shockley-Queisser (SQ) limit by minimizing radiative and nonradiative voltage losses.

Novel A-π-D-π-A type non-fullerene acceptors of dithienyl diketopyrropopyrrole derivatives to enhance organic photovoltaic applications: a DFT study.

To boost the photovoltaic attributes of organic photovoltaic cells, seven dithienyl diketopyrropopyrrole (TDPP) donor-based A-π-D-π-A (acceptor-bridge-donor-bridge-acceptor) type molecules (TM1-TM7) were formulated by modifying the electron accepting ends of the reference molecule (TMR). Optical and quantum chemical parameters of seven synthesized molecules were investigated using density functional theory with the MPW1PW91/6-31G(d,p) functional. Several parameters that can be used to measure and improve the efficiency of solar cells have been analyzed and summed up. These parameters include binding energy of exciton, excitation energy of electron, reorganization energies, dipole moment, molecular electrostatic potential, charge mobility, wavelength of maximum absorption, open circuit voltage, short circuit current, fill factor, density of states, transition density matrices, as well as iso-surface and non-covalent interactions. Thus, all of our proposed structures are perceived to be superior to the reference in terms of the maximum possible solar energy yield in solar cells with bulk heterojunctions, as determined by analyses of our designed molecules for the aforementioned parameters.

Effect of the Push–Pull Electronic Structure of Nonfullerene Acceptor Molecules on the Interfacial Charge Dynamics in Heterojunction Organic Solar Cells

Nonfullerene acceptor (NFA) molecules have attracted significant attention in high‐efficient heterojunction organic solar cells (OSCs) due to their push–pull electronic structures. Herein, using a universal quantum model for an organic donor/acceptor interface composed of a polymer donor and an NFA molecule, effect of the NFA molecular electron push and pull ability on the interfacial charge dynamics in the case of donor excitation is focused on. It is confirmed that energy and charge transfer coexist and compete during the interfacial charge dynamics, by which an interfacial hybrid state is created, and the quantitative correlations of the generation rates for different component states (e.g., donor exciton, acceptor exciton, and charge transfer state) with the NFA molecular electron push and pull ability are separately clarified. It is found that, by strengthening the NFA molecular electron push ability, competition between charge and energy transfer presents a nonmonotonous behavior; by strengthening the electron pull ability, charge transfer is always promoted and energy transfer is inhibited. This study provides a microscopic understanding for the interfacial charge dynamics modulated by tuning the NFA molecular push–pull electronic structure and thus sheds light on further improving the performance of heterojunction OSCs by rational designs of NFA molecules.

High electron mobility due to extra π-conjugation in the end-capped units of non-fullerene acceptor molecules: a DFT/TD-DFT-based prediction.

A combination of high open-circuit voltage (Voc) and short-circuit current density (Jsc) typically creates effective organic solar cells (OSCs). To enhance the open-circuit voltage, we have designed three new fullerene-free acceptor molecules with elongated π-conjugation in the end-capped units. Y-series-based newly designed molecules (CPSS-4F, CPSS-4Cl, CPSS-4CN) exhibited a narrow energy bandgap with high electron mobility. Red shift in the absorption spectrum with high intensities is also noted for designed molecules. Low binding and excitation energies of designed molecules favor easy excitation of exciton in the excited state. Further, CPSS-4F, CPSS-4Cl, and CPSS-4CN exhibited better open-circuit voltage with favorable molecular orbitals contributions. Transition density analysis (TDM) was also performed to locate the total transitions in the designed molecules. Outcomes of all analyses suggested that designed molecules are effective contributors to the active layer of organic solar cells.

The Importance of Nonequilibrium to Equilibrium Transition Pathways for the Efficiency and Stability of Organic Solar Cells.

Controlled morphology of solution-processed thin films have realized impressive achievements for non-fullerene acceptor (NFA)-based organic solar cells (OSCs). Given the large set of donor-acceptor pairs, employing various processing conditions to realize optimal morphology for high efficiency and stable OSCs is a strenuous task. Therefore, comprehensive correlations between processing conditions and morphology evolution pathways have to be developed for efficient performance and stability of devices. Within the framework of the blend system, crystallization transitions of NFA molecules are tracked utilizing the first heating scan of differential scanning calorimeter (DSC) measurement correlating with respective morphology evolution of blend films. Real-time dynamics measurements and morphology characterizations are combined to provide optimal morphology transition pathways as NFA molecules are shown to be released from the mixed-phase to form balanced ordered packing with variant processing conditions. Polymer:NFA films are fabricated using blade coating incorporating solvent additive or thermal annealing as processing conditions as a correlation is formulated between performance and stability of solar cells with morphology transition pathways. This work demonstrates the significance of processing condition-controlled transition pathways for the realization of optimal morphology leading to superior OSC devices.

Quinoxaline based unfused non-fullerene acceptor molecules with PTB7-Th donor polymer for high performance organic solar cell applications

Unfused non-fullerene acceptors possess advantages such as simplicity of synthesis, low toxicity, high yield with less manufacturing cost. In the present era, the rapid emergence of new unfused acceptors with high yields and stability is an urgent need. This report has developed four new fullerene-free quinoxaline-based unfused acceptor molecules (QX1 to QX4) for high-performance organic solar cell applications. All designed molecules have a long conjugating backbone which facilitates easy charge transportation between donor and acceptor ends. Different physiochemical, optoelectrical, and photovoltaic properties of designed molecules have been explored through density functional theory (DFT), and time-density functional theory (TD-DFT). A significant reduction in energy bandgap with red-shifting in absorption spectrum was noted for QX1 to QX4. Further, QX1 to QX4 exhibited good values of open-circuit voltage with low excitation and binding energies. Transition density matrix (TDM) analysis was also performed to explore the charge transfer behavior in the designed molecule. In addition, QX1 to QX4 expressed high mobility of electrons and holes with high molecular orbitals contributions. Outcomes of different geometric parameters suggested that QX1 to QX4 are excellent acceptor molecules (when blended with PTB7-Th polymer) for the active layer of organic solar cells.

Ab Initio Study of Two-Dimensional Cross-Shaped Non-Fullerene Acceptors for Efficient Organic Solar Cells.

In the present work, five novel non-fullerene acceptor molecules are represented to explore the significance of organic solar cells (OSCs). The electro-optical properties of the designed A–D–A-type molecules rely on the central core donor moiety associated with different halogen families such as fluorine, chlorine, and bromine atoms and acyl, nitrile, and nitro groups as acceptor moieties. Among these, M1 exhibits the maximum absorption (λmax) at 728 nm in a chloroform solvent as M1 has nitro and nitrile groups in the terminal acceptor, which is responsible for the red shift in the absorption coefficient as compared to R (716 nm). M1 also shows the lowest value of the energy band gap (2.07 eV) with uniform binding energy in the range of 0.50 eV for all the molecules. The transition density matrix results reveal that easy dissociation of the exciton is possible in M1. The highest value of the dipole moment (4.6 D) indicates the significance of M4 and M2 in OSCs as it reduces the chance of charge recombination. The low value of λe is given by our designed molecules concerning reference molecules, indicating their enhanced electron mobility. Thus, these molecules can serve as the most economically efficient material. Hence, all newly designed non-fullerene acceptors provide an overview for further development in the performance of OSCs.

DFT analysis of different substitutions on optoelectronic properties of carbazole-based small acceptor materials for Organic Photovoltaics

In this present study, we have investigated a series of six new novels A-π-D-π-A type small non-fullerene acceptor molecules to enhance the efficiency of organic solar cells. The designed acceptors consist of carbazole moiety as donor (central core) and 3-ethylrhodanine moiety as end-capped acceptor group which is linked via different conjugated π-linkers namely benzo[c][1,2,5]thiadiazole, benzo[c][1,2,5]oxadiazole, thiophene, furan, and [1,2,5]oxadiazolo[3,4-c]pyridine. DFT (HSE06) and TD-DFT (M05) calculations have been carried out with 6-311G(d,p) basis set to investigate the effect of different π-linkers on the charge transfer rate, stability, and optoelectronic properties. Different π-linkers have resulted in smaller HOMO-LUMO energy gap as compared to reference. All investigated molecules M1, M2, M4, M5 and M6 have shown significant bathochromic shift of 31, 12, 92, 78 and 47 nm compared to R except M3 which has shown slightly blue shift of 22 nm, respectively. The reorganization energy analysis predicted the ambipolar behavior of designed molecules. Molecular electrostatic potential maps (MEP), the density of state (DOS), and electron density difference maps (EDDM) analysis have shown the stability parameters and confirmed the higher charge transfer between different fragments within the designed molecules. Thusly, energy level analysis indicates that designed molecules M1, M2, M4 and M5 could act as suitable non-fullerenes acceptors with previously designed PffBT4T-2OD donor for practical solar cells applications.

Designing benzothiadiazole based highly efficient non-fullerene acceptor molecules for organic solar cells

This research is carried out to investigate photovoltaic characteristics of the six modified molecules derived from benzothiadiazole core-based reference molecule JY5, using four different non-fullerene acceptors at ωB97XD/6-31G** via TD-DFT approach. To check the efficiency of these designed molecules dipole moment, band gap, binding energy, chemical-potential, soft and hard character, electrophilicity, light harvesting efficiency, open circuit voltage and fill factor are studied along with transition density matrix, molecular electro-potential surface, density of states and photoinduced electron transfer (PET). Amidst JY5-W1 to JY5-W6 structures, JY5-W4 molecule shows a broad absorption range with a λmax of 458 nm. JY5-W3 and JY5-W4 molecules shows the highest electron mobilities. The outstanding light harvesting efficiencies (>0.90) make the designed molecules a good candidate for organic solar cells. HOMO-LUMO gaps parameterize Voc as a key factor in evaluating photovoltaic outcome of designed molecules (electrophilic in nature) so, PTB7-Th is considered as a preferred donor as its lower HOMO (−5.01 eV) and higher LUMO level (−2.60 eV) results in increased Voc predicting an efficient organic solar cell.

Chemical Design Rules for Non‐Fullerene Acceptors in Organic Solar Cells (Adv. Energy Mater. 44/2021)

Non-Fullerene Acceptors In article number 2102363, Denis Andrienko and co-workers summarize the chemical design rules of non-fullerene acceptor molecules for use in efficient organic solar cells. In particular, they propose that the energy level bending that promotes the generation of free charges requires a planar acceptor–donor–acceptor molecular architecture, and molecular alignment parallel to the interface. These design rules are benchmarked against existing non-fullerene acceptors and are used to pre-screen a set of molecular building blocks for new acceptors with potentially high power conversion efficiencies.

Molecular engineering of indenoindene-3-ethylrodanine acceptors with A2-A1-D-A1-A2 architecture for promising fullerene-free organic solar cells

Considering the increased demand and potential of photovoltaic devices in clean, renewable electrical and hi-tech applications, non-fullerene acceptor (NFA) chromophores have gained significant attention. Herein, six novel NFA molecules IBRD1–IBRD6 have been designed by structural modification of the terminal moieties from experimentally synthesized A2-A1-D-A1-A2 architecture IBR for better integration in organic solar cells (OSCs). To exploit the electronic, photophysical and photovoltaic behavior, density functional theory/time dependent-density functional theory (DFT/TD-DFT) computations were performed at M06/6-311G(d,p) functional. The geometry, electrical and optical properties of the designed acceptor molecules were compared with reported IBR architecture. Interestingly, a reduction in bandgap (2.528–2.126 eV), with a broader absorption spectrum, was studied in IBR derivatives (2.734 eV). Additionally, frontier molecular orbital findings revealed an excellent transfer of charge from donor to terminal acceptors and the central indenoindene-core was considered responsible for the charge transfer. Among all the chromophores, IBRD3 manifested the lowest energy gap (2.126 eV) with higher λmax at 734 and 745 nm in gaseous phase and solvent (chloroform), respectively due to the strong electron-withdrawing effect of five end-capped cyano groups present on the terminal acceptor. The transition density matrix map revealed an excellent charge transfer from donor to terminal acceptors. Further, to investigate the charge transfer and open-circuit voltage (Voc), PBDBT donor polymer was blended with acceptor chromophores, and a significant Voc (0.696–1.854 V) was observed. Intriguingly, all compounds exhibited lower reorganization and binding energy with a higher exciton dissociation in an excited state. This investigation indicates that these designed chromophores can serve as excellent electron acceptor molecules in organic solar cells (OSCs) that make them attractive candidates for the development of scalable and inexpensive optoelectronic devices.

Designing small organic non-fullerene acceptor molecules with diflorobenzene or quinoline core and dithiophene donor moiety through density functional theory

The non-fullerene acceptors A1–A5 with diflourobenzene or quinoline core (bridge) unit, donor cyclopenta[1,2-b:3,4-b′]dithiophene unit and 2-(2-methylene-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile as acceptor unit with additional phenyl, fulvene or thieno[3,2-d]pyrimidinyl 5-oxide groups have been designed through DFT calculations. The optimization of molecular geometries were performed with density functional theory (DFT) at B3LYP 6-31G (d,p) level of theory. The frontier molecular orbital (FMO) energies, band gap energies and dipole moments (ground and excited state) have been calculated to probe the photovoltaic properties. The band gap (1.42–2.01 eV) and dipole moment values (5.5–18. Debye) showed that these designed acceptors are good candidates for organic solar cells. Time-Dependent Density Functional Theory (TD-DFT) results showed λmax (wave length at maximum absorption) value (611–837 nm), oscillator strength (f) and excitation energies (1.50–2.02 eV) in gas phase and in CHCl3 solvent (1.48–1.89 eV) using integral equation formalism variant (IEFPCM) model. The λmax in CHCl3 showed marginal red shift for all designed acceptors compared with gas phase absorption. The partial density of states (PDOS) has been plotted by using multiwfn which showed that all the designed molecules have more electronic distribution at the donor moiety and lowest at the central bridge. The reorganization energies of electron (λe) (0.0007 eV to 0.017 eV), and the hole reorganization energy values (0.0003 eV to − 0.0403 eV) were smaller which suggested that higher charged motilities. The blends of acceptors A1–A5 with donor polymer D1 provided open circuit voltage (Voc) and ∆HOMO off-set of the HOMO of donor and acceptors. These blends showed 1.04 to 1.5 eV values of Voc and 0 to 0.38 eV ∆HOMO off set values of the donor–acceptor bends which indicate improved performance of the cell. Finally, the blend of D1–A4 was used for the study of distribution of HOMO and LUMO. The HOMO were found distributed on the donor polymer (D1) while the A4 acceptor was found with LUMO distribution. Based on λmax values, and band gap energies (Eg), excitation energies (Ex), reorganization energies; the A3 and A4 will prove good acceptor molecules for the development of organic solar cells.