Non-exhaust Particulate Matter Research Articles

Tribological Behavior of Friction Materials Containing Aluminum Anodizing Waste Obtained by Different Industrial Drying Processes

With sustainability dominating the industry, recycling the generated waste from different processes is becoming increasingly important. This study focuses on recycling waste generated during aluminum anodizing waste (AAW) in friction material formulations for automotive braking applications. However, before utilization, the waste needs to be pre-treated, which mainly involves drying. Hence, four different industrial drying methods were studied to dry the AAW, and the corresponding characteristics were observed by evaluating its residual humidity and crushability index. The waste powders were further characterized using FT-IR and SEM/EDXS to understand their constituents. The initial analysis showed that the waste subjected to the drying process P2 and P1 with the lowest final humidity fetched the most desirable results, with P1 having the simpler drying procedure. The AAW powders were added in a commercial friction material formulation at 6 and 12 wt.% and subjected to friction, wear, and non-exhaust particulate matter analysis. The worn surfaces were analyzed using SEM/EDXS evaluation to understand the extension and composition of the deposited secondary contact plateaus. It was seen that the 12 wt.% addition of waste processed using the P1 technique provided the most satisfactory friction, wear, and emission characteristics, along with expansive secondary contact plateaus with a good contribution of the waste in its formation. This study showed a good relationship between the processing method and a formulation’s tribological and emission characteristics, thereby paving the way for using this drying method for other waste requiring pre-treatment.

Emission inventory of heavy metals from on-road vehicles in Xiamen, China, from 2015 to 2060

Reducing vehicle emissions to improve air quality has been widely adopted by policy makers. However, insufficient attention has been paid to non-exhaust particulate matter (PM) and the associated heavy metals (HMs) from on-road vehicles, which can cause adverse health effects. In this study, emission inventories of PM2.5 and PM10 and the associated HMs from on-road vehicles in Xiamen, China, were established from 2015 to 2060 under a business-as-usual scenario. In the base year 2021, the total emissions of HMs associated with primary PM2.5 and PM10 were 1.88 × 104 kg and 3.96 × 104 kg, respectively, with the dominant contributions from brake wear and road surface wear. The emissions of HMs were overwhelmingly dominated by light-duty passenger cars and heavy-duty trucks. Fe, Ba, Zn, Cu, Mn, and Ti together accounted for about 97% of the total HMs. High-density emission areas were concentrated in urban centers. From 2015 to 2060, an increasing trend in total HMs emissions was observed due to the superimposed effect of decreasing diesel exhaust and increasing non-exhaust brake wear and road wear. However, the trends of the individual HMs were different from each other. The U-shaped distribution patterns of the relative cancer and non-cancer risks of HMs were observed between 2015 and 2060. Vehicle electrification alone is not enough to effectively reduce the potential health risk of vehicle-related HMs in the future. Reducing HMs from brake wear should be encouraged to use in electric vehicle. Uncertainties in the emissions of HMs were quantified using the Monte Carlo simulation.

Effect of internal and external damping in the reduction of non-exhaust particulate matter emissions in a low metallic friction material formulation

Friction-induced vibrations in an automotive braking system are of serious concern, leading to different repercussions. Numerous conventional and unconventional methods have been proposed to curb these vibrations, which are also observed to be directly related to generating non-exhaust particulate matter emissions. In this study, an in-house formulated friction material, tested in the form of pins, was subjected to internal damping by adding rubber content from 0 to 3 wt% and external damping by wrapping the different pins in rubber tape. The DMTA showed a decrease in storage modulus and an increase in loss factor with the increase in rubber content. The pin density decreased with the increase in the rubber content. Dry sliding friction, wear, emissions, and vibrations tests were conducted on a pin on disc tribometer with relevant attachments to measure emissions and vibrations. A large drop in vibrations was observed with the rubber content, irrespective of external damping. On the other hand, a significant reduction in wear, emissions, and vibrations was observed with the sample containing the highest rubber addition and with the damping tape. This study showed the feasibility of employing the combination of internal and external damping, emphasizing the optimum rubber content in friction material formulations.

Toxic Tire Wear Compounds (6PPD-Q and 4-ADPA) Detected in Airborne Particulate Matter Along a Highway in Mississippi, USA.

Tire wear particles (TWPs) are a major category of microplastic pollution produced by friction between tires and road surfaces. This non-exhaust particulate matter (PM) containing leachable toxic compounds is transported through the air and with stormwater runoff, leading to environmental pollution and human health concerns. In the present study, we collected airborne PM at varying distances (5, 15 and 30m) along US Highway 278 in Oxford, Mississippi, USA, for ten consecutive days using Sigma-2 passive samplers. Particles (~ 1-80μm) were passively collected directly into small (60 mL) wide-mouth separatory funnels placed inside the samplers. Particles were subsequently subjected to solvent extraction, and extracts were analyzed for TWP compounds by high resolution orbitrap mass spectrometry. This pilot study was focused solely on qualitative analyses to determine whether TWP compounds were present in this fraction of airborne PM. The abundance of airborne TWPs increased with proximity to the road with deposition rates (TWPscm-2day-1) of 23, 47, and 63 at 30m, 15m, and 5m from the highway, respectively. Two common TWP compounds (6PPD-Q and 4-ADPA) were detected in all samples, except the field blank, at levels above their limits of detection, estimated at 2.90and 1.14 ng L-1, respectively. Overall, this work suggests airborne TWPs may be a potential inhalation hazard, particularly for individuals and wildlife who spend extended periods outdoors along busy roadways. Research on the bioavailability of TWP compounds from inhaled TWPs is needed to address exposure risk.

Evaluating city road dust emission characteristics with a dynamic method: A case study in Luoyang, China

Road dust, a significant contributor to non-exhaust particulate matter emissions in urban transport, poses considerable health risks, necessitating accurate and high-resolution data for effective control. The traditional AP-42 method offers data on point-specific dust emissions, while vehicle-based testing ascertains the relative emission intensity in the road network. However, a clear mathematical relationship between these measurements has been elusive, limiting efficiency in emission control. By integrating the On-board Conventional Pollutant Monitoring System with the AP-42 method, we devised a dynamic link between the concentration of particles in vehicle plumes and actual road dust emissions. This relationship is substantiated by a notable correlation (R2 = 0.91) between our emission factors and those calculated using the AP-42 method. Significant variations emerged in dust emission factors across road types, with changes between −30.1 % to +57.79 % from the average (0.05 g·vehicle−1·km−1), in tandem with traffic flow fluctuations of approximately ±90 %. Meteorological factors, except for continuous rainfall, showed minimal impact on dust emissions. However, our findings revealed a significant underestimation (58.87 %) of road dust PM10 emissions by the AP-42 method. Intriguingly, we found that short-range emission hotspots substantially contribute to total emissions, suggesting a potential 50 % reduction by controlling merely 8.8 % ± 2.5 % of the total road length. Our research elucidates the interplay between road dust emissions, road types, and human activities. The application of a dynamic, high-resolution assessment method enhances our understanding of the impacts of road dust on urban particulate pollution, allows accurate hotspot identification, and aids in developing efficacious strategies for air quality enhancement.

Origin of non-exhaust PM in cities by individual analysis of particles collected by honey bees (Apis mellifera)

Urban areas present multiple challenges to scientists interested in unraveling the source, transport, and fate of airborne particulate matter (PM). Airborne PM consists of a heterogeneous mixture of particles with different sizes, morphologies, and chemical compositions. However, standard air quality stations only detect the mass concentration of PM mixtures with aerodynamic diameters ≤10 μm (PM10) and/or ≤ 2.5 μm (PM2.5). During honey bee foraging flights, airborne PM up to 10 μm in size attaches to their bodies, making them suitable for collecting spatiotemporal data on airborne PM. The individual particulate chemistry of this PM can be assessed using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy on a sub-micrometer scale, allowing accurate identification and classification of the particles.Herein, we analyzed the PM fractions of 10–2.5 μm, 2.5–1 μm, and below 1 μm in average geometric diameter collected by bees from hives located in the city of Milan, Italy. Bees showed contamination by natural dust, originating from soil erosion and rock outcropping in the foraging area, and particles with recurrent heavy metal content, most likely attributed to vehicular braking systems and possibly tires (non-exhaust PM). Notably, approximately 80% of non-exhaust PM was ≤1 μm in size. This study provides a possible alternative strategy to apportion the finer fraction of PM in urban areas and determine citizens’ exposure. Our findings may also prompt decision-makers to issue policy addressal for non-exhaust pollution, especially for the ongoing restructuring of European regulations on mobility and the shift toward electric vehicles whose contribution to PM pollution is debated.

Rapid generation of aged tire-wear particles using dry-, wet-, and cryo-milling for ecotoxicity testing

Strict environmental laws have been enacted to regulate the emission of exhaust particulate matter (PM), which is one of the most hazardous pollutants that reduce air quality and pose a serious risk to the human health. In addition, non-exhaust PM, such as road wear, tire wear, and brake wear debris, is a significant source of airborne pollutants. Road dust less than 100 μm in size may include tire wear particles (TWPs), which are broken down into finer particles with sizes on the order of tens of micrometers because of weathering. TWPs can be transported to water bodies via runoff, potentially contaminating water systems and negatively affecting aquatic ecosystems. Therefore, ecotoxicity tests using reference TWPs are required to investigate the impact of TWPs on the human health and environment. In this study, aged TWPs were produced using dry-, wet-, and cryo-milling methods, and the dispersion stability of TWPs in dechlorinated water was evaluated. Aged TWPs prepared by dry- and wet-milling had an average particle size of 20 μm, whereas pristine TWPs had an irregular shape and average particle size of 100 μm. The capacity of the ball-milling cylinder and excessively long 28-d generation time constrain the amount of aged TWPs that can be produced through conventional milling. In contrast, cryo-milling reduces the particle size of TWPs at the rate of −275.0 μm/d, which is nine times higher than that upon dry- and wet-milling. Dispersed cryo-milled TWPs had a hydrodiameter of 2.02 μm and were more stable in the aqueous phase in relation to the other aged TWPs. The results of this study suggest that cryo-milled TWPs can be used for aquatic exposure assessments as controls for real-world TWPs.

Structural Causality Between Road Traffic and Particulate Matter Concentrations in Urban Areas

Road traffic makes a major contribution to air pollution by emitting solid and liquid particles, also known as particulate matter, into the air. However, the causal relationship between road traffic and particulate matter emissions has not been adequately explored, primarily because traffic is the result of dynamic interactions involving many real-time variables, such as volume and speed. This study used structural equation modeling to quantify this complex causal relationship. A one-year survey using a mobile laboratory was conducted to collect data on particulate matter concentrations and traffic, which were then combined with weather statistics provided by the Korea Meteorological Administration. The key finding of this study suggests that greater attention in research and policy should be directed toward non-exhaust particulate matter emissions from road traffic.

A novel path towards limiting non-exhaust particulate matter emissions of a commercial friction material through the addition of metallurgical slag

Keeping recycling and the circular economy in mind, this study explores the reduction in emission of a highly optimized, commercially employed friction material formulation through the addition of metallurgical slags from a basic oxygen furnace in varying quantities from 6 to 38 wt%. The various compositions were paired with a pearlitic grey cast iron counterface and tested on a pin on disc tribometer. The friction coefficient and pin wear increased with the slag addition but were still within the permissible limit when compared to the original formulation. Specimens with higher slag content observed extremely compacted and extended secondary contact plateaus, which also recorded significant slag presence. The extended plateaus detached in the form of chunks from the mating surfaces, which settled on the equipment hardware and restricted the production of airborne particles. From an industrial symbiosis perspective, the addition of metallurgical slags proved to be a promising way of obtaining green friction materials with reduced emissions.

Filtering performance of ceramic filter with mullite whisker for non-exhaust particulate matter from transportation

Fabrication and filtering performance of ceramic filter were investigated to reduce non-exhaust particulate matter (PM) from vehicles. For this purpose, filter needs to be porous structure with high mechanical strength, thus it can be operated with low differential pressure. When the vehicle runs at a high speed, wheel temperature rises up to 700 °C. Therefore, filter material for non-exhaust PM filter also requires high temperature durability to be operated under such condition. Porous ceramic filter with mullite whiskers, which has advantages of high temperature durability and mechanical strength, was prepared using replica template method and MoO3 catalyst. The fabricated ceramic filter with mullite whiskers showed improved filtering performance for non-exhaust PM. Initially, the filtering performance was 56.3% for PM2.5 and 88.0% for PM10. The filtering performance gradually improved over filtering time to 86.4% for PM2.5 and 93.0% for PM10. The differential pressure was confirmed as 210 Pa, which was applicable for non-exhaust PM filter of vehicles.

Characterization of Particle Number Setups for Measuring Brake Particle Emissions and Comparison with Exhaust Setups

The stringency of vehicle exhaust emissions regulations resulted in a significant decrease in exhaust particulate matter (PM) emissions over the years. Non-exhaust particles (i.e., from brakes and tyres) account for almost half or more of road transport-induced ambient PM. Even with the internal combustion engine ban in 2035, electrified vehicles will still emit PM from brake and tyre wear. Consequently, non-exhaust PM emissions cannot decrease significantly without any regulatory measures. Because independent research carried out under different methods is not readily comparable, a Global Technical Regulation (GTR), which sets the procedures and boundaries of testing brake wear particle emissions, is currently under development. This overview describes the particle number (PN) measurement setup based on the well-known exhaust emissions PN methodology. We provide the technical requirements and the expected maximum losses. In addition, we estimate the effect of particle losses on the differences between different setups for typical size distributions observed during brake testing. Finally, we compare brake testing PN specifications to those of exhaust PN.

Characteristics of Real-World Non-Exhaust Particulates from Vehicles

The need to regulate the non-exhaust particulate matter (PM) emissions from vehicles has been discussed worldwide due to the bad environmental impact and the toxicity to the human body. In-depth studies have been precisely conducted on the analysis of the non-exhaust particulate matters, in particular, the amount of tire, brake and road wear particles and their proportion in the atmosphere. In this study, the influence of tire and road wear particles (TRWP) on PM in the atmosphere was investigated with tire and PM samples. The PM samples suspended in the atmosphere were collected with a high-volume sampler equipped with a quartz filter. Additionally, polycyclic aromatic hydrocarbons (PAHs) and metal components in tire rubber were analyzed as markers by pyrolysis–gas chromatography/mass spectrometry (pyrolysis–GC/MS), GC/MS, and inductively coupled plasma/mass spectrometry (ICP/MS). More vinylcyclohexene was detected than dipentene in the markers measured in the samples of tires equipped with vehicles driving on the road, while more dipentene was measured in total suspended particles (TSP) samples. Among the PAHs in tire samples, pyrene exhibited the highest concentration. Benzo(b)fluoranthene showed the highest concentration in the TSP samples. Among the metals, the highest concentration was zinc in all tire samples and calcium in TSP samples.

On airborne tire wear particles along roads with different traffic characteristics using passive sampling and optical microscopy, single particle SEM/EDX, and µ-ATR-FTIR analyses

Tire wear particles (TWPs) are a major category of microplastic pollution produced by friction between tires and road surfaces. This non-exhaust particulate matter (PM) is transported through the air and with runoff leading to environmental pollution and health concerns. Here, we collected airborne PM along paved roads with different traffic volumes and speeds using Sigma-2 passive samplers. Particles entering the samplers deposit onto substrates for analysis, or, as we modified it, directly into small (60 ml) separatory funnels, which is particularly useful with high particle loads, where a density separation aids in isolating the microplastics. We quantified putative TWPs (∼10–80 µm) deposited on the substrates (primarily adhesive tape on glass slides) and in the funnels using stereomicroscopy. Putative TWP deposition rates (particles/cm2/day ± SD) at 5 m from the road were highest near a busy highway (324 ± 129), followed by a boulevard with moderate traffic (184 ± 93), and a slow traffic avenue (29 ± 7). We observed that deposition rates increased within proximity to the highway: 99 ± 54, 180 ± 88, and 340 ± 145 at 30, 15, and 5 m, respectively. We show that TWP abundances (i.e., deposition and mass concentration) increase with vehicle braking (driving behavior). We observed no differences (p > 0.05) between the separatory funnel and adhesive tape collection methods. In addition, we were able to obtain FTIR spectra of TWPs (>10 µm) using µ-ATR-FTIR. Both deserve further scrutiny as novel sampling and analytical approaches. In a separate sampling campaign, we differentiated 1438 particles (∼1–80 µm) deposited on boron substrates into TWP, metal, mineral, and biogenic/organic classes with single particle SEM/EDX analysis based on morpho-textural-chemical classification and machine learning. The results revealed similar concentration trends with traffic (high > moderate > low), with the distribution of particle sources alike for the highway and the moderate road: TWPs (∼38–39%) > biogenic (∼34–35%) > minerals (∼23–26%), and metallic particles (∼2–3%). The low traffic road yielded a much different distribution: biogenic (65%) > minerals (27%) > TWPs (7%) > metallic particles (1%). Overall, this work provides much-needed empirical data on airborne TWPs along different types of roads.

Concentration and inorganic elemental analysis of particulate matter in a road tunnel environment (Žilina, Slovakia): Contribution of non-exhaust sources

Particulate matter (PM) is present in the surrounding air. The tunnel environment is no exception, where the PM source is road traffic. In a broader sense, the tunnel can be described as a separate point source of air pollution from which PM pollutants spread to the portal parts and the external environment. PM originates from the exhaust and non-exhaust processes of road traffic (brake wear, tire wear, road surface wear, and road dust re-suspension). This study deals with the specification of non-exhaust PM emissions in a tunnel environment where the primary source is road traffic. PM measurements took place in the “Považský Chlmec” highway tunnel with a length of 2,118 m directly in the tunnel tube and near the tunnel portal. PM measurements were performed using gravimetric and optical methods. PM chemical analyses were performed using energy-dispersive X-ray fluorescence (EDXRF). The concentration of PM in the tunnel was on average: PM10 = 30.76 μg/m3 and PM2.5 = 15.66 μg/m3 and near the tunnel portal PM10 = 14.38 μg/m3 and PM2.5 = 8.74 μg/m3. The average traffic volume in the tunnel tube was 2,274 veh/24 h. Using EDXRF, the main chemical elements Al, Br, Ca, Cl, Cr, Cu, Fe, K, Mg, Mn, Na, P, Si, S, Ti, and Zn were identified in the PM. Chemical element concentrations in PM10 and PM2.5 were subjected to factor analysis (FA) and principal component analysis (PCA) to determine the origin of PM. Two sources were identified for PM10 and three for PM2.5. Absolute principal component scores (APCS) in conjunction with multiple regression analysis (MRA) were used to determine the source contribution to the production of PM10 and PM2.5.

Exhaust and non-exhaust airborne particles from diesel and electric buses in Xi'an: A comparative analysis

Switching diesel buses (DBs) to electric buses (EBs) has been a global trend to reduce the use of fossil fuels and improve air quality. However, buses electrification may lead to additional vehicle weight, which may emit more non-exhaust particulate matter (PM) emissions. It remains debatable whether buses' electrification will successfully improve air quality as excepted. To assess the effect of the buses' electrification on the levels of PM emissions, PM emission factors (EFs) were evaluated from EBs and equivalent DBs. In addition, the total mass of PM emissions from EBs and equivalent DBs in 2021 was calculated in Xi'an using the real-world number and mileage of EBs. The non-exhaust PM EFs from EBs were larger than total exhaust and non-exhaust PM EFs from DBs, indicating that the electrification of buses would cause an increase in the level of PM emissions. The total annual mass of PM emissions from EBs was apparently higher than that from DBs. Moreover, a sensitivity analysis showed that tire wear, brake wear, and road wear PM emissions were more reliant on vehicle mileage, whereas resuspension of road dust was more dependent on vehicle weight. This finding can serve as a guideline for policymakers to design mitigation strategies for reducing extra PM emissions due to the electrification of buses by reasonably reducing vehicle weight and annual mileage.

Comparison of total PM emissions emitted from electric and internal combustion engine vehicles: An experimental analysis

Electric vehicles (EVs) are regarded as zero emission vehicles due to the absence of exhaust emissions. However, they still contribute non-exhaust particulate matter (PM) emissions, generated by brake wear, tire wear, road wear, and resuspended road dust. In fact, because EVs are heavier than internal combustion engine vehicles (ICEVs), their non-exhaust emissions are like to be even higher. While total PM emissions, including exhaust and non-exhaust PM emissions, from ICEVs and EVs have been compared based on the emission factors (EFs) listed in national emission inventories, there have been no comparisons based on experimental determinations.In this study, exhaust and non-exhaust emissions generated from a gasoline ICEV, diesel ICEV, and EV were experimentally investigated. The results showed that the EFs for the total PM emissions of ICEVs and EV were dependent on the inclusion of secondary exhaust PM, the brake pad type, and the regenerative braking intensity of the EV. When only primary exhaust PM emissions were considered in vehicles equipped with non-asbestos organic (NAO) brake pads, the total PM10 EF of the EV (47.7–49.3 mg/V·km) was 10–17 % higher than those of the gasoline ICEV (42.3 mg/V·km) and diesel ICEV (43.2 mg/V·km). However, in vehicles equipped with low-metallic (LM) brake pads, the total PM10 EF of the EV (49.2–57.7 mg/V·km) was comparable or lower than those of the gasoline ICEV (56.3 mg/V·km) and diesel ICEV (57.2 mg/V·km). When secondary PM emissions were included, the EF was always significantly lower for the EV than ICEVs. The total PM10 EF of the EV (47.7–57.7 mg/V·km) was lower than those of the gasoline ICEV (56.5–70.5 mg/V·km) and diesel ICEV (58.0–72.0 mg/V·km). Since secondary PM particles are mostly of submicron size, the EFs of the PM2.5 fraction of the ICEVs (28.7–33.0 mg/V·km) were two times higher than those of the EV (13.9–17.4 mg/V·km).

Quantitative analysis of the concentration of nano‑carbon black originating from tire-wear particles in the road dust

Exhaust and non-exhaust particulate matter (PM) is regarded as the most significant airborne during driving. Among the source of non-exhaust PM, the tire-wear particles (TWP) can be quantified using pyrolysis-gas chromatography/mass spectrometry (Py-GC–MS). TWPs are fragmented by continuous weathering once exposed to the road. Approximately 5 wt% of carbon black (CB) bound in the rubber matrix of TWPs tends to detach from it, and thus some portion of free-bound CB could be co-existed in the road dust. Although there are existing methods for analyzing pure CB and TWPs, only few analysis techniques on the amount of free-bound CB in contaminant samples have been discovered. Herein, we propose a method for quantifying the total and free-bound CB in road dust using a combination of four analytical tools: a semi-continuous carbon analyzer, element analyzer, thermogravimetric analyzer, and Py-GC–MS. This study is the first attempt in quantifying the concentration of nano-CB derived from TWPs in road dust. The proposed methodology was applied to the samples collected from five open sites, three closed sites, and four types of air conditioner (AC) filters in passenger vehicles. Compared to the samples obtained in open sites, the road dust in the closed sites exhibited 21.5 times higher TWP content (59,747 mg/kg) and 5.1 times higher free-bound CB content (14,632 mg/kg). In addition, unintentional driver respiratory exposure to PM fixed in the vehicle filters was discovered owing to the increase in CB and TWP contents in aged AC filters.

Effect of treadwear grade on the generation of tire PM emissions in laboratory and real-world driving conditions

Tires generally wear out due to the friction between the tire and the road surface. Minimizing tire wear could reduce the non-exhaust particulate matter (PM) emissions from tires. Typically, tire treadwear grade can be used as an indicator of PM emissions from tires. Tires that wear out quickly will produce higher PM emissions than more durable tires. In this study, the effect of treadwear grade on the generation of tire PM emissions was investigated through laboratory and on-road driving measurements. In the laboratory measurements, a tire wear simulator installed in an enclosed chamber was used to eliminate artifacts caused by interfering particles during the generation and measurement of tire wear particles. For realistic on-road driving measurements, a mobile sampling vehicle was employed to sample road dust. The road dust was chemically analyzed using pyrolysis gas chromatography–mass spectrometry (GC–MS) to characterize the tire-road wear particles.Both measurements showed that the higher treadwear grade generated lower tire PM emissions due to the high strength of the rubber, except for the UTQG 700 tire. The UTQG 700 tire, which had the highest treadwear grade, produced higher PM emissions than the UTQG 350 and 500 tires because it readily formed the fine particles due to lamellar peeling rather than tearing or curling of tire treads. Notably, tire nanoparticles were observed in laboratory measurements due to the volatilization and nucleation of the sulphur (S) and zinc (Zn) compounds in the tire tread due to the frictional heat between the tire and paved road surface.

A novel study on the reduction of non-exhaust particulate matter emissions through system vibration control.

The need to reduce non-exhaust particulate matter emissions is of paramount importance as they pose repercussions on human lives and the environment. In this study, a novel way to limit emissions is proposed based on the minimization of the vibration of the mating bodies. Two model friction material formulations were tested in the form of pins and paired with a pearlitic grey cast iron disc counterface in a laboratory pin on disc apparatus. To reduce the vibrations, a damping tape was wrapped around the pins. With the damping of vibration, a significant drop in the emissions was recorded, and this was correlated with the friction layer establishment during sliding, which observed low disruption. It is believed that the use of this method for reducing emissions can accompany the optimization phase of the brake squeal noise of friction materials, thereby, providing new design perspectives.

BRAVES database Version 1: non-exhaust particulate matter vehicular emissions in Brazil.

BRAVES database Version 1: non-exhaust particulate matter vehicular emissions in Brazil.