No-till Planter Research Articles

Study on Operating Vibration Characteristics of Different No-Tillage Planter Row Units in Wheat Stubble Fields

Study on Operating Vibration Characteristics of Different No-Tillage Planter Row Units in Wheat Stubble Fields

Sowing depth stability analysis and test verification of no-tillage planter parallel 4-bar row unit

The sowing depth stability and consistency of the no-tillage planter, particularly the high-speed operation, are poor. A reason for this is that the structure and parameter selection of no-tillage planter row unit profiling mechanism are unreasonable. The stability and consistency of sowing depth is beneficial when the upper and lower links of the parallel 4-bar profiling mechanism (PFPM) are parallel to the ground, but this principle is not satisfied on the uneven no-till soil. To improve the stability of gauge wheels downforce (GWD) and sowing depth of no-tillage planter row unit. The variation law of spring additional downforce (SAD) with tilt angle of parallel 4-bar profiling mechanism (PFPM) and connection offset of spring is discussed by constructing the steady state analysis matrix equation of PFPM. Additionally, the influence of tilt angle of PFPM and SAD on the stability of the sowing depth was analyzed. Based on the single factor control variable test method, bench and field tests were conducted. The test results show that the SAD increases nonlinearly with the increase in the degree of tilt of PFPM from downward to upward. Under the condition that four springs are installed and the tilt angle of PFPM is between (−20°–20°), the maximum SAD is 485.95 N, 1236.64 N, and 2258.05 N when the spring connection offset is 44 mm, 79 mm, and 115 mm, respectively. When the tilt angle is 8° upward, the GWD increases by 429 N, 575 N, and 984 N, GWD stability increases by 42.31 %, 56.16 %, and 50.29 %, and ditching depth stability increases by 30.00 %, 12.50 %, and 30.00 % compared with that of the control group at the sowing speed of 8, 10, and 12 km/h, respectively. At the sowing speed of 10 km/h, when the PFPM is operated with spring-free and additional springs, the average GWD increases by 353 N, and the stability of GWD and ditching depth increases by 34.38 % and 20.00 %, respectively. The results showed that the tilt upward of PFPM and SAD were beneficial to improve the stability of the GWD and sowing depth of the no-tillage planter row unit. The results not only verify the correctness of theoretical analysis, but also provide theoretical basis for the design and application adjustment of high-speed no-tillage planter.

Optimizing Active Disturbance Rejection Control for a Stubble Breaking and Obstacle Avoiding Control System

In order to improve the obstacle avoidance control performance and anti-interference ability of a stubble breaking device of a no-tillage planter, a back-propagation neural network (BPNN)-optimized fuzzy active disturbance rejection control (ADRC) controller was designed to optimize the control performance of a servo motor. Firstly, a negative feedback mathematical model was established for the obstacle avoidance control system. Then, the nonlinear state error feedback (NLSEF) parameters in the fuzzy ADRC were intelligently optimized by the BPNN algorithm. In this way, a fuzzy ADRC controller based on BPNN optimization was formed to optimize the control process of a servo motor. Matlab/Simulink (R2022b) was used to complete the simulation model design and parameter adjustment. Consequently, the response time was 0.089 s using the BPNN fuzzy ADRC controller, which was shorter than the 0.303 s of the ADRC controller and the 0.100 s of the fuzzy ADRC controller. The overshoot was 0.1% using a BPNN fuzzy ADRC controller, which was less than the 2% of the ADRC controller and the 1% of the fuzzy ADRC controller. After noise signal interference was introduced into the control system, the regression steady state time of the BPNN fuzzy ADRC controller was 0.22 s, which was shorter than the 0.56 s of the ADRC controller and the 0.45 s of the fuzzy ADRC controller. A hardware-in-the-loop simulation experimental platform of the obstacle avoidance control system was constructed. The experiment results show that the servo motor control system has a fast dynamic response, small steady-state error and strong anti-interference ability for obstacle avoidance at the target height. Then, the control system error was within the allowable range. The servo motor control effect of the BPNN fuzzy ADRC was better than the ADRC and fuzzy ADRC. This optimized servo motor control method can provide a reference for improving the obstacle avoidance control effect problem of no-tillage seeders in stubble breaking operations on rocky desertification areas.

Straw movement and flow field in a crushing device based on CFD-DEM coupling with flexible hollow straw model

To accurately predict and evaluate the performance of the crushing device of no-till planter, it is strongly necessary to establish an accurate interaction model of the straw-crushing device coupling system. The traditional model has low prediction accuracy and cannot simulate the fracture characteristics of the straw during the operation of the crushing device due to the straw being usually regarded as a rigid body or a combination of rigid ball joints. In this paper, a breakable and flexible hollow straw model is first proposed and a CFD-DEM coupling model of the straw group-crushing device considering the effect of gas-solid two phase is also established. Afterwards, the corresponding verification experiments are conducted and the effect of working and structural parameters on the straw-throwing weight and crushing length is also analysed. It is demonstrated that the relative error between the simulation results and the experimental results for the straw crushing length is 7.7%, and the relative error for the straw-throwing weight is 7.1%, thereby verifying the correctness of the CFD-DEM model. Finally, the response surface method is also used to determine the optimal working and structural parameters of the crushing device and corresponding field tests verification is also conducted. Results indicate that the optimal parameter combination is as: the rotational speed of the crushing spindle is 2400 rpm, the inlet clearance is 30 mm and the starting point angle is 45°. Moreover, the crushing length after optimisation is 6.6% smaller than before optimisation, and the straw-throwing weight is increased by 11.5%.

Research and test of the measurement sensing device for the downforce of no-till planter row unit gauge wheels

Research and test of the measurement sensing device for the downforce of no-till planter row unit gauge wheels

高低畦小麦免耕播种机设计与试验

Aiming at the problems of low land utilization and serious water waste in the existing wheat planting pattern, a two-high and two-low wheat high-low border spaced apart planting mode was proposed, and a high and low borders wheat no-till planter that can finish stubbing, fertilization, border construction, seeding and other tasks was designed. The design and analysis of the ship-type ridging device were carried out, and the construction process was simulated to determine the optimal parameters. A field test was carried out, the average sowing depth was 3.17 cm, the qualification rate was 95%, the standard deviation was 0.38 cm, and the coefficient of variation was 12.06%. The average value of the width of the seedling belt was 9.40 cm, the qualification rate was 91.67%, the standard deviation was 0.29 cm, and the coefficient of variation was 3.09%. The average height difference between the high and low borders was 9.26 cm, the pass rate was 100%, the standard deviation was 0.35 cm, and the coefficient of variation was 3.83%. The average width of the borders was 52.18 cm, the qualified rate of the border width was 100%, the standard deviation was 1.00 cm, and the coefficient of variation was 1.93%. The differences between each index and the theoretical design are small and meet the agronomic requirements.

Design and experiment of a soybean shaftless spiral seed discharge and seed delivery device

When the driven stubble-breaking and anti-blocking no-till planter operates in the Southwest China, the stubble-breaking blades will impact with the ground as they cut through the soil and straw stubble, causing the planter to vibrate. This results in poor performances of the seed discharge by seed discharger and the seed guide by the seed guide tube. Based on the principle of spiral conveying, a soybean shaftless spiral seed discharge and seed delivery device was designed. The optimum seed filling size and speed range of the spiral blade were obtained by analyzing the size, force, and motion of soybean seeds of "ZhongHuang 37". The quadratic regression orthogonal rotation test and response surface method were used to analyze the operating parameters of the shaftless spiral seed discharge and seed delivery device by joint EDEM (Discrete Element Method)-RecurDyn simulation. The optimum parameters were obtained: the spacing of spiral was 11.4 mm, spiral outer radius was 5.5 mm, spiral inner radius was 2.9 mm and rotation speed was 10.4 r·s−1. Based on simulation and optimization results, the device was trialed and its field performance was tested. The results showed that at a surface slope of 16.1°, an average surface flatness of 8.9 cm, an average planter vibration frequency of 75.2 Hz, and an average amplitude of 7.2 mm, the average seeding qualification index, multiple index, missing seeding index, and damage index of the shaftless spiral seed discharge and seed delivery device were 92.6%, 5.03%, 2.4% and 0.92%, respectively, which were in line with the local agronomic requirements. The designed soybean shaftless spiral seed discharge and seed delivery device meets the requirements of the quality of no-till seeding and can provide a reference for the design and improvement of seed discharger and seed guide tube under poor ground leveling and long-distance seed delivery conditions.

Design and Test of Single-Disc Opener for No-Till Planter Based on Support Cutting

To solve the problem of low straw-cutting efficiency of single-disc openers of no-till planters under conditions of high soil moisture content, a single-disc furrowing and straw-cutting device was designed based on the support-cutting principle. To improve the straw-cutting ability of the disc opener when it operates under high-moisture-content soil conditions and to make sure that the straw that is not cut by the disc coulter can be cut smoothly by the disc opener, the support shovel was designed, and the operation mechanism of the support shovel device was analyzed. The soil moisture content, the support shovel’s entry angle, the support shovel’s entry gap angle, and the support shovel’s tip margin were identified as the factors influencing the device design through the theoretical analysis of the furrowing and straw-cutting device. Through the discrete element method (DEM), a single-factor simulation test was first conducted to analyze how different soil moisture contents affected the device’s ability to cut straw, and the results showed that the number of broken bonds was lowest when the soil moisture content was 20 ± 1%, and the time taken for the straw to be wholly cut off was also the longest. Then, a quadratic orthogonal simulation test was conducted to construct a regression model and optimize the parameters at the soil moisture content of 20 ± 1%, and the results revealed that the significant order of each factor’s influence on the number of broken bonds is as follows: entry gap angle, entry angle, and shovel tip margin. In addition, the device’s overall operation quality was better when the entry angle was 49°, the entry gap angle was 0°, and the shovel tip margin was 10 mm. At this time, the number of broken bonds was predicted to be 506. Finally, the simulation validation test was run, and the number of broken bonds was obtained to be 478, with a relative error of 5.6% from the predicted value. According to the optimal parameters to complete the device trial production and field test, the results show that the average cut-off rate of the device is 71.7%, the stability coefficient of the furrowing depth is 90.87%, and the performance of the furrow opening is excellent, which meets the requirements of a no-tillage seeding operation. This study can provide a reference for the design and improvement of no-tillage seeding machines under conditions of high soil moisture content.

Design and Experiment of Row Cleaner with Staggered Disc Teeth for No-Till Planter

In view of the large amount of wheat straw coverage and the difficulty with the high-speed working process used in traditional rotary tillage row cleaner. A row cleaner with staggered disc teeth for no-till planting was designed. It was determined that installation with a forward inclination α, horizontal declination β, and forward speed v0 of the machine were the main factors affecting the straw cleaning rate Y1 and working resistance Y2, and the range of values for structural parameters and motion parameters of the row cleaner were determined. Taking α, β, and v0 as the factors and Y1 and Y2 as the response indexes, using EDEM 2018 software to simulate the straw cleaning process under different parameters and determine the influence of each parameter on the straw cleaning performance. After performing a soil bin test, the results showed that there was no straw entanglement and blockage, and the passability was better than that of the traditional flat disc separated row cleaner. When α was 70°, β was 30°, v0 was 8 km/h, and the embedded depth h of the soil (straw) was 55 mm, the average straw cleaning rate was the highest, which was 90.59%. This study provides a new idea for the design of high-speed corn no-till planters in the Huang-Huai-Hai area of China.

Design of animal drawn cereal grains no-till planter

The development of no-till system in Eritrea presents a significant opportunity to achieve earlier and more timely planting. Tillage wastes a lot of time, energy and a lot of money in the form of fuel, labor and equipment concerning with the life style of Eritrean farmers. Therefore, to solve this problem animal drawn no-till planter is designed to make the farming operation easy and efficient, simple to operate, it reduces the amount of work for tillage and it combines several steps of tillage in machine. No-till system can be designed in different forms of tractor mounted, manual operated and animal drawn planter. These mechanized systems would introduce additional barriers to adoption including the high cost of investment, availability and cost of fuel and the need to use syndication ownership models. So due to the economical standard living of local farmers animal drawn no-till planter is more efficient for small holder farmers. Animal drawn no-till planter is designed with a pulling force 73.5kgf: walking speed of 0.6m/s and with the frame dimension of 1000mmx450mmx50mm. The equipment’s used in this design are made locally available, making the overall cost cheap and affordable to the farmers in contrast with no-till planter imported from overseas so that farmers do not face difficulties in obtaining these planters and providing a basic saving from budgeting a large amount of currency for importing a conventional tiller machine. To attain better accuracy, fabrication of the designed animal drawn planter in the actual field with local materials is advisable to give major concern in the future work. And also, testing and evaluation performance of the animal drawn no-till planter is highly recommended.

Design and experiment of the pneumatic pressure control device for no-till planter

Design and experiment of the pneumatic pressure control device for no-till planter

Detection Method of Straw Mulching Unevenness with RGB-D Sensors

Returning straw to the field is very important of for the conservation tillage to increase land fertility. It is vital to detect the unevenness of the straw covering to evaluate the performance of no-tillage planter, especially for the ones with returning full amount of straw. In this study, two kinds of RGB-D(Red, Green, Blue-Depth) sensors (RealSense D435i and Kinect v2) were applied to estimate the straw mulching unevenness by detecting the depth of straw coverage. Firstly, the overall structure and working principle of no-tillage planter with returning the full amount of straw was introduced. Secondly, field images were captured with the two kinds of RGB-D sensors after no tillage planter operation. Thirdly, straw covering unevenness computing was carried on a system developed by Matlab. Finally, the correlation analysis was conducted to test for the relationship between the straw covering unevenness by manual and deep sensors, with R (correlation coefficient) of 0.93, RMSE(Root Mean Square Error) of 4.59% and MAPE(Mean of Absolute Percentage Error) of 3.86% with D435i sensor, and with R of 0.915, RMSE of 6.53% and MAPE of 13.85% with Kinect V2, which showed both kinds of RGB-D sensors can acquire the unevenness of straw covering efficiently. The finding can provide a potential way to detect the unevenness of straw coverage and data support for operation evaluation and improvement of no-tillage planter.

Design and Experimental Study of a Bi-Directional Rotating Stubble-Cutting No-Tillage Planter

In view of the problem of a large amount of stubble and straw in Southwest China, it is difficult to carry out no-tillage sowing operations. Based on the principle of supported cutting, a bi-directional rotating stubble-cutting no-tillage planter was designed. According to the extracted left and right mouth contours of Batocera horsfieldi (Hope), the blade curve of a bi-directional rotating cutterhead was designed. The discrete element models were established regarding ‘bi-directional rotating disc cutter, straw and soil’, ‘fertilizer apparatus and fertilizer’, and ‘opener and soil’ in the Extended-Domain-Eigenfunction Method (EDEM) software. The optimal working parameters were analyzed using a quadratic regression orthogonal rotation test and response surface methodology. Accordingly, the prototype was manufactured and the field performance test was carried out. The best working parameters of the machine were as follows: the forward speed of the machine was 0.9 m·s−1, the cutter spacing was 60 mm, the forward speed was 150 r·min−1, and the reverse speed was 313 r·min−1. The field experiment results showed that the average cutting rate of corn straw was 95.72% using the anti-blocking device when the straw mulching amount was 1.63 kg·m−2. The average sowing depth was 5.4 cm, the average fertilization depth was 10.1 cm, and the average seed–fertilizer spacing was 4.7 cm. The qualified rates of sowing depth, fertilization depth, and spacing were 88.89%, 100%, and 100%, respectively. The designed bi-directional rotating stubble-cutting no-tillage planter can meet the requirements of no-tillage sowing in Southwest China. This study can provide reference for the design and improvement of no-tillage planters under the conditions of a large amount of stubble and straw.

Design and Analysis of Pneumatic Downforce Regulating Device for No-Till Corn Planter

To avoid the issues of undesired soil compaction and seeding depth variation caused by the downforce fluctuation of the corn no-till planter, the influence of the structural parameters of the air spring on the downforce was researched in this paper, by establishing the gas–solid coupling simulation model of the air spring. The downforce test bench was built to verify the simulation model; the test showed that the vertical output force error of the simulation model was 4.79%, the pitch diameter error was 0.76%, and the pressure error was 5.07%. The cord angle, piston angle and piston diameter were used as influencing factors to carry out single-factor experiments. The influences of structural parameters on downforce were analyzed from four aspects: the vertical output force, the vertical stiffness, the pressure difference and the deformation rate. The results showed that the cord angle reduced the effective area and its change rate during deformation by limiting the radial deformation of the bellow. When the cord angles were 30°, 45° and 60°, the deformation rates were 65.6%, 20.3% and 4.8%, respectively. The cord angle had a positive effect on the vertical output force when the cord angle was in the range of 30~56°, and it had a negative impact in the range of 56~60°. As the cord angle increased, the vertical stiffness decreased. As the piston angle increased, the effective area of the air spring decreased, and the change in internal pressure decreased, reducing its vertical output force and stiffness. The piston diameter had little effect on the internal pressure and deformation rate. It increased the vertical output force and stiffness by increasing the effective area. The structural parameters of the air spring had a significant impact on the stability of the downforce; the structure of the air spring should be optimized according to the downforce demand of the corn no-till planter.

Experiments on the Influence of Corn Straw Morphological Combinations on Timely No-Tillage Sowing Soil Temperature and Moisture in Cold Regions

After corn mechanical harvest in autumn in the cold region of northeast China, straw mulching leads to high soil topsoil water content and slow ground temperature rise in the spring sowing season, which may result in a no-tillage planter being unable to operate in time, delayed sowing date, poor seedling emergence quality, and low grain yield. Based on the problems of high moisture content and low temperature in soil topsoil in the spring sowing season in conservation tillage with straw mulching, an experimental study on timely sowing in the spring sowing season was carried out from the perspective of combination optimization of attribute parameters of straw mechanical treatment. Taking the four mechanical treatment attributes as experimental factors, including straw length, straw shape, mulching form (surface covering, inter-ridge covering, and inter-ridge mixed soil covering), and stubble height after corn harvest in autumn of 2019 as experimental factors, and soil topsoil moisture content and temperature during spring sowing in 2020 as evaluation indexes, a field plot experiment was carried out by four factors and three levels of orthogonal combination test method. The results showed that all the factors had significant influence on soil topsoil moisture content and soil topsoil temperature (p < 0.05). It is helpful to reduce the moisture content of soil topsoil and increase the temperature of soil topsoil by increasing the length of corn stalk, breaking the stalk moderately, covering the stalk between ridges, and increasing the stubble height of stalk. Design-Expert software was used to optimize the parameters. The results showed that when the length of straw was 150 mm, the shape of straw was half-cut (dividing straw into two parts evenly along the axis), the mulch was between ridges, and the stubble height was 600 mm, the moisture content of soil topsoil was 22~24% and the temperature of soil topsoil was higher than 8 °C during spring sowing. After corn harvest in autumn of 2021, corn stalks were treated in that year according to the results of parameter optimization combination. The soil topsoil moisture content and temperature were measured to be 24.4% and 8.2 °C, respectively, in the spring sowing season of 2022, which proved that the optimization results in this experiment were credible. The experimental results provide a technical reference for the implementation of conservation tillage with straw surface mulching in the cold region of northeast China.

Design and Optimization of a Soil-Covering Device for a Corn No-Till Planter

Aiming to solve the problems of easy generation of clods, poor soil fluidity and poor soil-covering effect in the no-tillage seeding operation mode, this study has designed a soil-covering device with a soil-closing function for the chisel-type furrow opener of a corn no-tillage planter. Theoretical analysis and design of the soil dividing plate and the soil-covering disc were carried out, and the key parameters were determined. Then, the soil-covering device with soil-closing function and the soil movement model was constructed in Altair EDEM, and the spatial soil particle mobility was analyzed. The numerical simulation method was combined with the center plane composite response test scheme to carry out the simulation test, and the optimal working parameter combination was obtained. The operating speed was 6.35 km·h−1, the inclination angle of the soil-covering disc was 60°, the opening angle of the soil-covering disc was 70°, and the inclination angle of the soil dividing plate was 40°. A comparative test of the soil-covering effect and performance was carried out, and the results showed that the designed device was better than the traditional soil-covering device in terms of the consistency of soil-covering thickness and the stability of seed position deviation. The relative errors of the soil bin experiment results and the simulation optimization results for the cover soil thickness and seed position deviation were 5.7% and 11.1%, respectively. The operation effect of the designed soil-covering device with soil-closing function meets the requirements of soil covering under no-tillage conditions and provides a basis for the research and development of soil-covering suppression technology and devices under no-tillage seeding mode.

Design and experiment of a straw clearing mulching no-tillage planter

When soybean is replanted after wheat in parts of China, problems such as a short sowing period, large straw yield and poor mechanization technology emerge; these problems increase the difficulty of sowing subsequent soybeans and negatively affect soybean quality and yield. In addition, the ecological problems associated with straw burning and soil degradation become increasingly severe. Here, a straw clearing mulching no-tillage planter with integrated functions of lateral straw clearing anti-blocking, precision sowing, pesticide spraying, and straw mulching was developed. This planter could perform several functions, including surface straw clearing before sowing, herbicide spraying after sowing, and straw surface uniform mulching. A lateral straw clearing mulching device was designed, and the main parameters and values affecting the working performance of the device were determined. To verify the technical performance and working quality of straw clearing mulching no-tillage sowing, field experiments were conducted, testing the effects of straw clearing mulching no-tillage sowing (SCMNS) and stubble eliminating rotary-tillage sowing (SERS) on the sowing quality, seedling emergence rate, soil hydrothermal characteristics, soybean yield, and comprehensive economic benefits. The qualified indices of seed spacing and sowing depth of SCMNS were 87.2% and 76.5%, respectively, which were significantly higher than those of SERS. SCMNS could enhance the ground temperature, reduce water evaporation, improve water storage, and promote soil moisture conservation. The seedling emergence date of SCMNS was one day earlier than that of SERS. The seedling emergence rate of SCMNS was 89.8%, which was significantly higher than that of SERS. The soybean yields of SCMNS (2809.2 kg·hm−2) and SERS (2207.4 kg·hm−2) significantly differed. SCMNS improved the comprehensive economic benefits by increasing soybean yield and reducing production costs; the net income of 1147.82 €·hm−2 was 50.27% higher than that of SERS.

Design and Experiment of Symmetrical Spiral Row-Sorting of the Straw Device Based on Kinematics Analysis

This paper designed a symmetrical spiral row-sorting of the straw device (SSRSD) under the condition that the no-till anti-blocking knife cut and chopped the straw to guarantee the machine’s passing capacity. The row-sorting blade (RB) of the symmetrical spiral mechanism (SSM) pushed the straw that fell into the straw hopper to the non-sowing area on both sides of the sowing belt and played the role of row-sorting the straw. Based on a theoretical analysis of the relationship between the material-bearing capacity limit of the SSM and the straw mulching quantity (SMQ) in the actual operating area, the critical parameters of the SSM and its value ranges were determined. The results show that the average straw removing rate (SRR) of the no-till planter with the SSRSD was 87.98%, and the passing capacity of the machine was great. Compared with the no-till planter without the SSRSD, the average SRR was increased by 20.7%.

Design and Test of Elastic Tooth Type Lateral Straw Clearing Roller Based on the Straw Clearing and Mulching No-Tillage Precision Planter

Aiming at the problems of large soil disturbance, high power consumption and strong vibration during the operation of the 2BMFJ series straw clearing and mulching no-tillage precision planter with rigid teeth, an elastic tooth type lateral straw clearing roller was designed and the key parameters and values affecting the operation performance of the device were determined through theoretical analysis. Orthogonal test method was adopted to implement parameter combination improvement test with the length of tooth rod, the clearance of roller center from ground, the circumferential number of elastic teeth and the angular velocity of roller as test factors and straw clearing rate, power consumption and vibration intensity as performance evaluation indexes. The results showed that: all the factors had extremely significant effects on the straw clearing rate and power consumption performance evaluation indexes, except the clearance of roller center from ground had no significant effect on the vibration intensity performance evaluation indexes, the other factors have significant effects. Parameter optimization combination: At the planter forward speed of 7.2 km/h, the length of toothed rod was 270 mm, the clearance of roller center from ground was 360 mm, the circumferential number of elastic teeth was 8, the angular velocity of roller was 52 rad/s and the performance evaluation indexes were as follows: straw clearing rate was more than 90%, power consumption was less than 1.7 kW and vibration intensity was less than 85 m/s2. Through the comparative test of the elastic tooth and rigid tooth type lateral straw clearing roller, there was no significant difference in the straw clearing rate between the two, but there were significant differences in the power consumption and vibration intensity. The elastic tooth type lateral straw cleaning roller reduced power consumption by 63.3% and vibration intensity by 43.2%.

Design and Experiment of Spiral Discharge Anti-Blocking and Row-Sorting Device of Wheat No-Till Planter

Aiming at the problems of the poor passing capacity of machines and low cleaning rate of seed strip during wheat no-tillage sowing in annual double cropping areas of North China, a spiral discharge anti-blocking and row-sorting device (SDARD) was designed and is reported in this paper. After the straw was cut and chopped by the high-velocity rotating no-till anti-blocking knife group (NAKG), the straw was thrown into the spiral discharging mechanism (SDM) behind the NAKG. The chopped straw was discharged to the non-sowing area to reach the effect of seed strip cleaning through the interaction between the SDM and the row-sorting of straw mechanism (RSM). Based on a theoretical analysis for determining the parameters of crucial components, the quadratic rotation orthogonal combination test method was adopted, and the operating velocity of machines (OVM), the rotary velocity of the spiral shaft (RVSS), and the height of the holding hopper from the ground (HHHG) were selected as the test factors. The straw cleaning rate (SCR) was taken as the test index. The discrete element simulation test was carried out, the regression model of the SCR was established, and parameters optimization and field test were carried out. The results show that the significant order of the three influencing factors on the SCR was HHHG > OVM > RVSS. The optimal combination of operating parameters was that OVM was 5 km/h, RVSS was 80 r/min, and HHHG was 10 mm. Under the optimal parameter combination, the average SCR was 84.49%, which was 15.5% higher than the no-till planter without the device, and the passing capacity of machines was great, which met the agronomic requirements of no-tillage sowing of wheat in annual double cropping areas. This study could provide a reference for the design of no-tillage machines.