No-flow Process Research Articles

Investigation of the Flip-Chip Package With BCB Underfill for W-Band Applications

Flip-chip package has great potential for use in millimeter-wave applications. However, the coefficient of thermal expansion mismatch between the chip and the substrate usually generates thermal stresses that fracture the flip-chip structure. The use of underfills with low dielectric loss is essential to improve the mechanical strength and reliability of the flip-chip package. Benzocyclobutene (BCB) was used in this study as the underfill material for the flip-chip structure using the no-flow process. The flip-chip structure with BCB injection provides good RF performance with a return loss of better than 18 dB and an insertion loss of 0.6 dB up to 100 GHz, in addition to a lower dielectric loss. Furthermore, thermal cycle and shear force tests show that the underfill injection can significantly improve the reliability of a flip-chip package.

Effects of substrate design on underfill voiding using the low cost, high throughput flip chip assembly process and no-flow underfill materials

The formation of underfill voids is an area of concern in the low cost, high throughput, or flip chip assembly process. This assembly process involves placement of a flip chip device directly onto the substrate pad site covered with pre-dispensed no-flow underfill. The forced motion of chip placement causes a convex flow front to pass over pad and solder mask-opening features promoting void capture. This paper determines the effects of substrate design on the phenomena of underfill voiding using the no-flow process. A full-factorial design experiment analyzes several empirically determined factors that can affect void capture in no-flow processing. The substrate design parameters included pad height, solder mask opening height, pad/solder mask opening separation, and pad pitch. The process parameters include chip placement velocity and underfill viscosity. The process robustness is measured in terms of the number of voids created during chip placement, and is further analyzed for the location and any visible modes of void formation. The goal of the work is to determine improved substrate designs to minimize voiding in flip chip processing using no flow underfills.

Assembly of lead-free bumped flip-chip with no-flow underfills

Lead-free solder reflow process has presented challenges to no-flow underfill material and assembly. The currently available no-flow underfill materials are mainly designed for eutectic Sn-Pb solders. This paper presents the assembly of lead-free bumped flip-chip with developed no-flow underfill materials. Epoxy resin/HMPA/metal AcAc/Flux G system is developed as no-flow underfills for Sn/Ag/Cu alloy bumped flip-chips. The solder wetting test is conducted to demonstrate the fluxing capability of the underfills for lead-free solders. A 100% solder joint yield has been achieved using Sn/Ag/Cu bumped flip-chips in a no-flow process. A scanning acoustic microscope is used to observe the underfill voiding. The out-gassing of HMPA at high curing temperatures causes severe voiding inside the package. A differential scanning calorimeter (DSC) used to study the curing degree of the underfill after reflow with or without post-cure. The post-curing profiles indicate that the out-gassing of HMPA would destroy the stoichiometric balance between the epoxy and hardener, and result in a need for high temperature post-cure. The material properties of the underfills are characterized and the influence of underfill out-gassing on the assembly and material properties is investigated. The impact of lead-free reflow on the material design and process conditions of no-flow underfill is discussed.

Application assessment of high throughput flip chip assembly for a high lead-eutectic solder cap interconnect system using no-flow underfill materials

Flip chip on board (FCOB) is one of the most quickly growing segments in advanced electronic packaging. In many cases, assembly processes are not capable of providing the high throughputs needed for integrated surface mount technology (SMT) processing (Tummala et al, 1997). A new high throughput process using no-flow underfill materials has been developed that has the potential to significantly increase flip chip assembly throughput. Previous research has demonstrated the feasibility and reliability of the high throughput process required for FCOB assemblies. The goal of this research was to integrate the high throughput flip chip process on commercial flip chip packages that consisted of high lead solder balls on a polyimide passivated silicon die bonded with eutectic solder bumped pads on the laminate substrate interface (Qi, 1999). This involved extensive parametric experimentation that focused on the following elements: no-flow process evaluation and implementation on the commercial packages, reflow profile parameter effects on eutectic solder wetting of high lead solder bumps, interactions between the no-flow underfill materials and the package solder interconnect and tented via features, void capture and void formation during processing, and material set compatibility and the effects on long term reliability performance.