Nitrogen Nickel-free Austenitic Stainless Steel Research Articles

Corrosion behavior of high nitrogen nickel-free austenitic stainless steel in the presence of artificial saliva and Streptococcus mutans

High nitrogen nickel-free austenitic stainless steels (HNSs) have great potentials to be used in dentistry owing to its exceptional mechanical properties, high corrosion resistance, and biocompatibility. In this study, HNSs with nitrogen of 0.88 wt% and 1.08 wt% displayed much lower maximum pit depths than 316L stainless steel (SS) after 21 d of immersion in abiotic artificial saliva (2.2 μm and 1.7 μm vs. 4.5 μm). Microbiologically influenced corrosion (MIC) evaluations revealed that Streptococcus mutans biofilms led to much severer corrosion of 316L SS than HNSs. Corrosion current densities of HNSs were two orders of magnitude lower than that of 316L SS after incubation of 7 d (37.5 nA/cm2 and 29.9 nA/cm2 vs. 5.63 μA/cm2). The pitting potentials of HNSs were at least 550 mV higher than that of 316L SS in the presence of S. mutans, confirming the better MIC resistance of HNSs. Cytotoxicity assay confirmed that HNSs were not toxic to MC3T3-E1 cells and allowed better sessile cell growth on them than on 316L SS. It can be concluded that HNSs are more suitable dental materials than the conventional 316L SS.

Nanoindentation creep deformation behaviour of high nitrogen nickel-free austenitic stainless steel

ABSTRACTNanoindentation tests of the high nitrogen nickel-free austenitic stainless steel (HNS) were performed with peak load in a wide range of 100–600 mN to investigate the nanoindentation creep deformation behaviours. The results of the nanoindentation creep tests have demonstrated that the load plateaus, creep strain rate and creep stress of the cold-rolled HNS are larger and its creep stress exponent is smaller than the solution-treated HNS. The analysis reveals that the obvious creep deformation behaviour in the cold-rolled HNS arises from the rapidly relaxed dislocation structures in the initial transition regime, while the small creep deformation behaviour of the solution-treatedHNS is mainly attributed to that the stable dislocation structures for the intensive interactions between dislocations.

Effect of cold deformation on corrosion fatigue behavior of nickel-free high nitrogen austenitic stainless steel for coronary stent application

Due to the excellent mechanical properties, good corrosion resistance, high biocompatibility and nickel-free character, the high nitrogen nickel-free austenitic stainless steel (HNASS) becomes an ideally alternative material for coronary stents. Stent implantation works in harsh blood environment after a balloon dilatation, i.e., the material is used in a corrosive environment with a permanent deformation. The present study attempts to investigate effects of pre-straining on high-cycle fatigue behavior and corrosion fatigue behavior of HNASS in Hank’s solution and the relevant mechanism for coronary stents application. It is found that higher pre-straining on HNASS results in higher strength and maintains almost same corrosion resistance. Fatigue limit of 0% HNASS is 550MPa, while corrosion fatigue limit is 475MPa. And improvement in fatigue limit of 20% and 35% pre-strained HNASS is in comparison with the 0% HNASS, while corrosion would undermine the fatigue behavior of HNASS. In a suitable range, the pre-straining had a beneficial effect on corrosion fatigue strength of HNASS, such as nearly 300MPa improved with 20% cold deformation. This result provides a good reference for predicting the life of HNASS stent and as well its design.

Strain rate and cold rolling dependence of tensile strength and ductility in high nitrogen nickel-free austenitic stainless steel**Project supported by the National Natural Science Foundations of China (Grant Nos. 51371089 and 51401083)

The tensile strength and ductility of a high nitrogen nickel-free austenitic stainless steel with solution and cold rolling treatment were investigated by performing tensile tests at different strain rates and at room temperature. The tensile tests demonstrated that this steel exhibits a significant strain rate and cold rolling dependence of the tensile strength and ductility. With the increase of the strain rate from 10−4 s−1 to 1 s−1, the yield strength and ultimate tensile strength increase and the uniform elongation and total elongation decrease. The analysis of the double logarithmic stress—strain curves showed that this steel exhibits a two-stage strain hardening behavior, which can be well examined and analyzed by using the Ludwigson equation. The strain hardening exponents at low and high strain regions (n2 and n1) and the transition strain (εL) decrease with increasing strain rate and the increase of cold rolling RA. Based on the analysis results of the stress–strain curves, the transmission electron microscopy characterization of the microstructure and the scanning electron microscopy observation of the deformation surfaces, the significant strain rate and cold rolling dependence of the strength and ductility of this steel were discussed and connected with the variation in the work hardening and dislocation activity with strain rate and cold rolling.

Immobilization of heparin/poly-l-lysine microspheres on medical grade high nitrogen nickel-free austenitic stainless steel surface to improve the biocompatibility and suppress thrombosis

Thrombosis formation, restenosis, and delayed endothelium regeneration continue to be a challenge for coronary artery stent therapy. To improve the hemocompatibility of cardiovascular implants and to selectively direct vascular cell behavior, a novel heparin/poly-l-lysine microsphere was developed and immobilized on a dopamine-coated surface. We chose medical grade high nitrogen nickel-free austenitic stainless steel as the stent material since it has better biocompatibility. The stability and structural characteristics of the microspheres changed with the heparin: poly-l-lysine concentration ratio. Antithrombin III binding was significantly enhanced. Furthermore, for plasma coagulation tests, the activated partial thromboplastin time and thrombin time were prolonged and depended on the heparinfunction. The modified exhibited excellent stability and anticoagulant activity, and efficiently accelerated endothelialization and anticoagulation. This work has potential application for the design of coronary artery stent surfaces tailored for vascular cell behavior.

Plastic flow behavior and its relationship to tensile mechanical properties of high nitrogen nickel-free austenitic stainless steel

Plastic flow behavior of high nitrogen nickel-free austenitic stainless steel with solution, hot rolling and cold rolling treatments were examined and analyzed by using the Ludwigson equation. It was shown that this stainless steel exhibit a two-stage strain hardening behavior, which can be well described by the Ludwigson equation. Based on the Ludwigson equation and the Considère instability criterion, two equations of the uniform plastic strain and the stress ratio (true ultimate tensile strength/true yield strength) to the strain hardening exponents were derived. Based on these two equations, the dependence of the strength and ductility on the true yield strength and strain hardening behavior was discussed and connected with the observation results of microstructures.

Biological behaviour of human umbilical artery smooth muscle cell grown on nickel-free and nickel-containing stainless steel for stent implantation.

To evaluate the clinical potential of high nitrogen nickel-free austenitic stainless steel (HNNF SS), we have compared the cellular and molecular responses of human umbilical artery smooth muscle cells (HUASMCs) to HNNF SS and 316L SS (nickel-containing austenitic 316L stainless steel). CCK-8 analysis and flow cytometric analysis were used to assess the cellular responses (proliferation, apoptosis, and cell cycle), and quantitative real-time PCR (qRT-PCR) was used to analyze the gene expression profiles of HUASMCs exposed to HNNF SS and 316L SS, respectively. CCK-8 analysis demonstrated that HUASMCs cultured on HNNF SS proliferated more slowly than those on 316L SS. Flow cytometric analysis revealed that HNNF SS could activate more cellular apoptosis. The qRT-PCR results showed that the genes regulating cell apoptosis and autophagy were up-regulated on HNNF SS. Thus, HNNF SS could reduce the HUASMC proliferation in comparison to 316L SS. The findings furnish valuable information for developing new biomedical materials for stent implantation.

Microstructure, mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel

Friction stir welding (FSW) was applied to a 2.4 mm thick high nitrogen nickel-free austenitic stainless steel plate using tungsten–rhenium (W–Re) tool. The high-quality weld was successfully produced at a tool rotational speed of 400 rpm and a traveling speed of 100 mm/min. The microstructure, mechanical and corrosion properties of the weld were studied. The nitrogen content of the weld was almost identical to that of base metal (BM). FSW refined grains in the stir zone (SZ) through dynamic recrystallization and led to increase in hardness and tensile strength within the SZ, while the ductility was slightly decreased. The failure of tensile specimens occurred in the BM. TEM results revealed precipitates of Cr23C6 of size ~ 1 μm in the SZ, although their content was small. The precipitation of Cr23C6 and increase in δ-ferrite in the SZ led to small decrease in both pitting and intergranular corrosion resistance.

Study of biocompatibility of medical grade high nitrogen nickel-free austenitic stainless steel in vitro

Adverse effects of nickel ions being released into the living organism have resulted in development of high nitrogen nickel-free austenitic stainless steels for medical applications. Nitrogen not only replaces nickel for austenitic structure stability but also improves steel properties. The cell cytocompatibility, blood compatibility and cell response of high nitrogen nickel-free austenitic stainless steel were studied in vitro. The mechanical properties and microstructure of this stainless steel were compared to the currently used 316L stainless steel. It was shown that the new steel material had comparable basic mechanical properties to 316L stainless steel and preserved the single austenite organization. The cell toxicity test showed no significant toxic side effects for MC3T3-E1 cells compared to nitinol alloy. Cell adhesion testing showed that the number of MC3T3-E1 cells was more than that on nitinol alloy and the cells grew in good condition. The hemolysis rate was lower than the national standard of 5% without influence on platelets. The total intracellular protein content and ALP activity and quantification of mineralization showed good cell response. We conclude that the high nitrogen nickel-free austenitic stainless steel is a promising new biomedical material for coronary stent development.

A Novel High Nitrogen Nickel-free Coronary Stents System: Evaluation in a Porcine Model

ObjectiveTo study the safety of the novel high nitrogen nickel-free austenitic stainless steel bare metal stents (BMS) in a recognized porcine coronary model and to select a better grid structure of it. MethodsThree types of stents were randomly implanted in different coronary arteries of the same pig: 316L stainless steel BMS (316L-BMS) (n=12), novel high nitrogen nickel-free stents Grid A (NF-A-BMS) (n=12) and novel high nitrogen nickel-free stents Grid B (NF-B-BMS) (n=12). In total, eighteen animals underwent successful random placement of 36 oversized stents in the coronary arteries. Coronary angiography was performed after 36 d of stents implantation. Nine animals were respectively sacrificed after 14 d and 36 d for histomorphologic analysis. ResultsQuantitative coronary angiography (QCA) showed similar luminal loss (LL) in the three groups: (0.21±0.17) mm for 316L-BMS, (0.16±0.12) mm for NF-A-BMS, (0.24±0.15) mm for NF-B-BMS (P>0.05). Histomorphomeric analysis after 15 d and 36 d revealed that there was also no significant difference among the three groups in neointimal area (NA) with similar injury scores respectively. High magnification histomorphologic examination showed similar inflammation scores in the three groups, but NF-A-BMS group had poorer endothelialization scores compared with NF-B-BMS group, 2.00±0.63 vs. 2.83±0.41 (P=0.015) at 15 d, which also could be proved by the scanning electron microscope. However, the difference could not been observed at 36 d. ConclusionsThe novel NF-BMS showed similar safety as 316L-BMS during the short-term study. NF-B-BMS had better endothelialization than NF-A-BMS and this may owe to the specific strut units.

Research on the properties of TIG welded joints of high nitrogen nickel-free austenitic stainless steel and welding wire

TIG welding tests were carried out on high nitrogen nickel-free austenitic stainless steel by solid solution treatment,with three kinds of self-developed high nitrogen alloyed flux cored wires obtained. The results show the microstructure of the welded joints is austenite in dendritic crystalwith strong corrosive resistance. The grains in HAZ zone hardly grew, and the bonding were perfect between weld and base metal. Furthermore, no obvious nitrogen pores are found in welds and fusion zone. Connector Rm of Mo–N Wire and Mo–Nb–N flux cored wire is higher than the base metal to 983 MPa.

Reduction of In-Stent Restenosis Risk on Nickel-Free Stainless Steel by Regulating Cell Apoptosis and Cell Cycle

High nitrogen nickel-free austenitic stainless steel (HNNF SS) is one of the biomaterials developed recently for circumventing the in-stent restenosis (ISR) in coronary stent applications. To understand the ISR-resistance mechanism, we have conducted a comparative study of cellular and molecular responses of human umbilical vein endothelial cells (HUVECs) to HNNF SS and 316L SS (nickel-containing austenitic 316L stainless steel) which is the stent material used currently. CCK-8 analysis and flow cytometric analysis were used to assess the cellular responses (proliferation, apoptosis, and cell cycle), and quantitative real-time PCR (qRT-PCR) was used to analyze the gene expression profile of HUVECs exposed to HNNF SS and 316L SS, respectively. Flow cytometry analysis revealed that 316L SS could activate the cellular apoptosis more efficiently and initiate an earlier entry into the S-phase of cell cycle than HNNF SS. At the molecular level, qRT-PCR results showed that the genes regulating cell apoptosis and autophagy were overexpressed on 316L SS. Further examination indicated that nickel released from 316L SS triggered the cell apoptosis via Fas-Caspase8-Caspase3 exogenous pathway. These molecular mechanisms of HUVECs present a good model for elucidating the observed cellular responses. The findings in this study furnish valuable information for understanding the mechanism of ISR-resistance on the cellular and molecular basis as well as for developing new biomedical materials for stent applications.

Analysis of Magnetism in High Nitrogen Austenitic Stainless Steel and Its Elimination by High Temperature Gas Nitriding

Stable austenitic structure in medical stainless steels is basically required for surgical implantation. A weak magnetism was found in a high nitrogen nickel-free austenitic stainless steel for cardiovascular stent application. This magnetic behavior in high nitrogen stainless steel was investigated by optical microscopy, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and superconducting quantum interference device (SQUID). The results showed that the magnetism came from the composition segregation of ferrite formation elements such as Cr and Mo in the steel and some delta-ferrites were locally formed during the pressurized electroslag remelting process. The magnetism of high nitrogen stainless steel could be eliminated by a proper high temperature gas nitriding (HTGN).

In vitro Study on a New High Nitrogen Nickel-free Austenitic Stainless Steel for Coronary Stents

Most commercialized coronary stents are made of 316L stainless steels due to its good combination of properties, and currently some new stents are made of cobalt-based alloy owing to its higher mechanical properties. However, the presence of high quantity of nickel and/or cobalt elements in these materials, which are known to trigger the toxic and allergic responses, has caused many concerns. Nickel-free austenitic stainless steels have been developed in order to solve these problems. In this paper, based on the development of a new Fe-Cr-Mn-Mo-N type high nitrogen nickel-free austenitic stainless steel, properties such as mechanical property, corrosion resistance in Hank's solution, and in vitro blood compatibility including the kinetic clotting time and the platelets adhesion, were investigated in comparison to the above two conventional materials, a 316L stainless steel and a Co-28Cr-6Mo alloy. The results showed that the new high nitrogen steel possessed better combination of mechanical properties, corrosion resistance and blood compatibility than those of 316L steel and the Co-28Cr-6Mo alloy, and can be a promising alternative material for manufacture of coronary stents.