Nitrogen-doped Ultrananocrystalline Diamond Research Articles

Preparation of Multi-Layer Graphene Using Nitrogen-Doped Ultrananocrystalline Diamond as a Solid-State Carbon Source

Preparation of Multi-Layer Graphene Using Nitrogen-Doped Ultrananocrystalline Diamond as a Solid-State Carbon Source

Microstructure control and mechanical properties of ultra-nanocrystalline diamond films

Ultra-nanocrystalline diamond (UNCD) films exhibit excellent mechanical properties because of their unique structure, such as small grain size and high grain boundary ratio. The effect of nitrogen atoms in nitrogen-doped UNCD films on their structure and mechanical properties deserves in-depth study. In this study, we focus on the microstructure control of UNCD films and its effect on the mechanical properties. Ultra-nanocrystalline diamond films were prepared using microwave plasma chemical vapor deposition under varying nitrogen flow rates. It was observed that the hardness and elastic modulus of UNCD films initially increased and then decreased with the increase of nitrogen flow rate. The structure of UNCD films was characterized using transmission electron microscopy and the crystal quality was analyzed through Raman spectroscopy. Nitrogen-interstitial atom defects were identified in the photoluminescence spectra. These defects contribute to shorter interatomic bonds and enhance the covalent bonds in the crystalline structure, resulting in an increase in hardness. The sp2/sp3 ratio and effective nitrogen atom concentration in the UNCD film were analyzed by X-ray photoelectron spectroscopy. The results indicate that an increase in the effective nitrogen atom concentration corresponds with a notable reduction in grain size, which is simultaneously accompanied by a rise in the number of grain boundaries. Meanwhile, the increase of sp2 content in the UNCD leads to the increase of grain boundary width and density, resulting in the increase of hardness and elastic modulus. This work provides theoretical basis and experimental guidance for the development of high performance UNCD films through precisely regulating the microstructure.

Impact of surface treatments on the electron affinity of nitrogen-doped ultrananocrystalline diamond

In recent years, various forms of nanocrystalline diamond (NCD) have emerged as an attractive group of diamond/graphite mixed-phase materials for a range of applications from electron emission sources to electrodes for neural interfacing. To tailor their properties for different uses, NCD surfaces can be terminated with various chemical functionalities, in particular hydrogen and oxygen, which shift the band edge positions and electron affinity values. While the band edge positions of chemically terminated single crystal diamond are well understood, the same is not true for nanocrystalline diamond, which has uncontrolled crystallographic surfaces with a variety of chemical states as well as graphitic grain boundary regions. In this work, the relative band edge positions of as-grown, hydrogen terminated, and oxygen terminated nitrogen-doped ultrananocrystalline diamond (N-UNCD) are determined using ultraviolet photoelectron spectroscopy (UPS), while the band bending is investigated using photoelectrochemical measurements. In contrast to the widely reported negative electrode affinity of hydrogen terminated single crystal diamond, our work demonstrates that hydrogen terminated N-UNCD exhibits a positive electron affinity owing to the increased surface and bulk defect densities. These findings elucidate the marked differences in electrochemical properties of hydrogen and oxygen terminated N-UNCD, such as the dramatic changes in electrochemical capacitance.

Control of Neuronal Survival and Development Using Conductive Diamond.

This study demonstrates the control of neuronal survival and development using nitrogen-doped ultrananocrystalline diamond (N-UNCD). We highlight the role of N-UNCD in regulating neuronal activity via near-infrared illumination, demonstrating the generation of stable photocurrents that enhance neuronal survival and neurite outgrowth and foster a more active, synchronized neuronal network. Whole transcriptome RNA sequencing reveals that diamond substrates improve cellular-substrate interaction by upregulating extracellular matrix and gap junction-related genes. Our findings underscore the potential of conductive diamond as a robust and biocompatible platform for noninvasive and effective neural tissue engineering.

Photoelectrochemical Modelling of Semiconducting Electrodes for Neural Interfacing

Semiconducting electrodes are increasingly utilised for neural interfacing applications, such as neural recording, stimulation, and photomodulation. To characterize the performance of these electrodes, photoelectrochemical analysis is often undertaken in biologically relevant electrolytes. These include electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and for photomodulation applications, photocurrent (PC) measurements. From such measurements, it is possible to deduce key properties of semiconductor surfaces, such as electrochemical impedance and capacitance, as well as mechanisms of charge transfer. To extract these parameters from the experimental data, equivalent electrical circuit modelling is often employed, but usually only for a single technique at a time which often misses key insights about the processes occurring at the electrode-electrolyte interface. Here we present an equivalent circuit model that simultaneously describes the results from CV, EIS, and PC transient measurements. Using semiconducting nitrogen-doped ultrananocrystalline diamond (N-UNCD) electrodes in saline solution, we show that the model describes physical mechanisms that occur at the interface with electrolyte, encompassing the space charge region, the electrical double layer, and the electrolyte. Using the model we are able to optimize parameters relevant for neural interfacing and suggest that this framework may assist in the characterization of other semiconducting electrodes.

Towards optical neuromodulation using nitrogen-doped ultrananocrystalline diamond photoelectrodes

Nitrogen-doped ultrananocrystalline diamond (N-UNCD) is a form of diamond electrode with near-infrared photoresponsivity, making it well suited for physiological applications. N-UNCD's photoresponsivity is strongly influenced by its surface. While it is known that oxygen treatment provides a higher photoresponsivity, a better understanding of its surface processes is needed to tailor the material for optical neuromodulation. This work examines the impact of various oxygen treatment methods, with aim of creating oxygen rich surfaces with different chemical and structural properties. Surface characterisation methods along with electrochemical and photoelectrochemical measurements and modelling were used to investigate the films. It was found that oxygen furnace annealing resulted in orders of magnitude improvement in the near-infrared photoresponsivity, to 3.75 ± 0.05 µA/W. This translates to an approximate 200 times increase in the photocurrent compared to the untreated surface. This enhancement in photocurrent is largely due to the changes in the chemical species present at the surface. The photocurrent is estimated to be sufficient for extra-cellular stimulation of brain neurons within the safe optical exposure limit, positioning N-UNCD as an excellent candidate to be used in next-generation photoelectrodes for photobiomodulation.

Zero-biased and visible-blind UV photodetectors based on nitrogen-doped ultrananocrystalline diamond nanowires

Taking advantage of the superflat surface of ultrananocrystalline diamond (UNCD), highly precise UNCD nanowire (NW) arrays were fabricated to develop high-performance UV photodetectors. The large surface-to-volume ratio of a nanowire significantly increases the number of surface trap states, and the reduced dimensionality effectively confines the active area of the charge carrier and shortens the transit time, which results in an enhanced photoconductivity and response speed. In this paper, the zero-biased UV photodetectors based on nitrogen-incorporated ultrananocrystalline diamond nanowire arrays have been demonstrated and characterized. The estimated responsivity was 2.0 A/W for 350 nm incident light when the device operated at room temperature. The UVA and UVB photocurrent signals from this visible blind photodetector were well defined with a rise and decay time of less than 1 s.

Size-Dependent Electrical Transport Properties in Conducting Diamond Nanostripes.

With the advances in nanofabrication technology, horizontally aligned and well-defined nitrogen-doped ultrananocrystalline diamond nanostripes can be fabricated with widths in the order of tens of nanometers. The study of the size-dependent electron transport properties of these nanostructures is crucial to novel electronic and electrochemical applications. In this paper, 100 nm thick n-type ultrananocrystalline diamond thin films were synthesized by microwave plasma-enhanced chemical vapor deposition method with 5% N2 gas in the plasma during the growth process. Then the nanostripes were fabricated using standard electron beam lithography and reactive ion etching techniques. The electrical transport properties of the free-standing single nanostripes of different widths from 75 to 150 nm and lengths from 1 to 128 μm were investigated. The study showed that the electrical resistivity of the n-type ultrananocrystalline diamond nanostripes increased dramatically with the decrease in the nanostripe width. The nanostripe resistivity was nearly doubted when the width was reduced from 150 nm to 75 nm. The size-dependent variability in conductivity could originate from the imposed diffusive scattering of the nanostripe surfaces which had a further compounding effect to reinforce the grain boundary scattering.

Nitrogen doped ultrananocrystalline diamond conductive layer grown on InGaN-based light-emitting diodes using nanopattern enhanced nucleation

This study grew nitrogen doped ultrananocrystalline diamond (N-UNCD) conductive layer on InGaN-based light emitting diodes (LEDs) using the concave nanopattern (CNP) enhanced nucleation. The low nucleation density of the N-UNCD on bare LEDs (Br-LED) resulted in an island morphology. The nucleation density of the N-UNCD increased significantly from 1.8 × 108 cm−2 for Br-LED to 3.6 × 109 cm−2 for LEDs with a CNP density of 6.1 × 109 cm−2 (CNP-LED). The N-UNCD preferred to nucleate inside the CNP during the initial growth stage. The N-UNCD islands then merged and grew laterally to form a continuous thin film within a thickness of 300 nm. The N-UNCD/CNP-LED exhibited a stable electroluminescence peak wavelength of ~447.1 nm in the injection current range of 10–100 mA. The decrease in the compressive stress due to removing the p-GaN layer (i.e. the CNP structure) resulted in a quantum confined Stark effect (QCSE) mitigation in the multi-quantum wells (MQWs). In addition, the lower turn on voltage caused a lower electric field in the MQWs and diminished the screen of the QCSE. The N-UNCD prepared by the proposed nucleation technique demonstrated a promising conductive layer for InGaN-based LEDs.

Enhanced electrochemical capacitance of nitrogen-doped ultrananocrystalline diamond through oxygen treatment

The electrochemical capacitance of nitrogen-doped ultrananocrystalline diamond (N-UNCD) can be dramatically increased by treating the surface with an RF-oxygen plasma. Such treated surfaces display excellent properties for use as electrodes in neural stimulation and recording. In the present work, we elucidate the origins of this phenomenon by investigating the effects of different methods of oxygen termination. We found that the increase in electrochemical capacitance is dependent on the details of the method used for oxygen termination. Whilst N-UNCD subjected to UV/ozone treatment, oxygen plasma treatment, and furnace annealing in oxygen gas all displayed increased surface capacitance, the highest capacitance was exhibited by the oxygen annealed sample, with which we achieved ~ 3 orders of magnitude increase in the electrochemical capacitance as compared to the as-grown sample. The maximum recorded capacitance was 3746 ± 132 µF cm−2, which is substantially greater than previously reported N-UNCD electrodes’ electrochemical capacitance (1070 µF cm−2, W. Tong. et al, 2016). Our findings point to the presence of sub-surface solid state capacitance which contributes significantly to the observed electrochemical capacitance of the oxygen terminated N-UNCD electrodes. When combined with the favourable biocompatibility and inertness of the N-UNCD, our approach may provide a route towards the development of advanced neural sensing and stimulating electrodes.

Impedance spectroscopy analysis of n-type (nitrogen-doped) ultrananocrystalline diamond/p-type Si heterojunction diodes

Heterojunction diodes are constructed by growing n-type (nitrogen-doped) ultrananocrystalline diamond (UNCD)/hydrogenated amorphous carbon (a-C:H) composite films onto p-type Si substrates in nitrogen and hydrogen mixed-gases by coaxial arc plasma deposition. The fabricated heterojunctions are analyzed regarding their film morphology and electrical properties. The complex structure of UNCD/a-C:H films, which consists of nano-sized-sp3 diamond grains and sp2-grain boundaries (GBs), makes it difficult to separate their contribution to electrical conductivity of the films using conventional characterization methods. In this paper we characterize the n-type UNCD/p-type Si heterojunction diode by employing impedance spectroscopy method, which can isolate the differing components that contribute to the overall conductivity of the film. The impedance spectroscopy is measured in the frequency range of 100 Hz to 2 MHz, with AC small signal superimpose on DC bias voltage in the range of 0–1 V. The influence of the bias on UNCD grains and GBs contribution to resistance and capacitance of UNCD/a-C:H film and n-UNCD/p-Si heterojunction is investigated by equivalent circuit model using fitting of the impedance data. The results revealed that the electrical conductivity is mainly controlled by the GBs rather than the UNCD grains. Furthermore, the extracted value of dielectric constant of N-doped UNCD/a-C:H film is found to be comparable with that of microcrystalline diamond, which indicates the capacitance contribution in the device is mainly originated from the UNCD grains. This study demonstrates capability of impedance spectroscopy to provide an obvious separated contribution of sp3 and sp2 bonded carbons to the electrical conductivity in their coexistence materials.

Nitrogen-doped Diamond Nanowire Gas Sensor for the Detection of Methane

Diamond-based sensors have shown great potential in the past few years due to their unique physicochemical properties. We report on the development of high-performance nitrogen-doped ultrananocrystalline diamond (UNCD) nanowire-based methane (CH4) gas sensors, taking advantage of a large surface-to-volume ratio and a small active area offered by the 1D nanowire geometry. The morphologic surface and crystalline structures of UNCD are also characterized by using scanning electron microscopy (SEM) and Raman scattering, respectively. By using synthesized nanowire arrays combined with 4-pin electrical electrodes, prototypic highly sensitive CH4 gas sensors have been designed, fabricated and tested. Various parameters including the sensitivity, response and recovery times, and thermal effect on the performance of the gas sensor have also been investigated in order to quantitate the sensing ability. Enhanced by the small grain size and porosity of the nanowire structure, fabricated nanowire UNCD sensors demonstrated a high sensitivity to CH4 gas at room temperature down to 2 ppm, as well as fast response and recovery times which are almost 10 times faster than that of regular nanodiamond thin film based sensors.

Near-infrared excitation of nitrogen-doped ultrananocrystalline diamond photoelectrodes in saline solution

Nitrogen-doped ultrananocrystalline diamond (N-UNCD) is a promising material for a variety of neural interfacing applications, due to its unique combination of high conductivity, bioinertness, and durability. One emerging application for N-UNCD is as a photoelectrode material for high-precision optical neural stimulation. This may be used for the treatment of neurological disorders and for implantable bionic devices such as cochlear ear implants and retinal prostheses. N-UNCD is a well-suited material for stimulation photoelectrodes, exhibiting a photocurrent response to light at visible wavelengths with a high charge injection density [A. Ahnood, A. N. Simonov, J. S. Laird, M. I. Maturana, K. Ganesan, A. Stacey, M. R. Ibbotson, L. Spiccia, and S. Prawer, Appl. Phys. Lett. 108, 104,103 (2016)]. In this study, the photoresponse of N-UNCD to near-infrared (NIR) irradiation is measured. NIR light has greater optical penetration through tissue than visible wavelengths, opening the possibility to stimulate previously inaccessible target cells. It is found that N-UNCD exhibits a photoresponsivity which diminishes rapidly with increasing wavelength and is attributed to transitions between mid-gap states associated with the graphitic phase present at the grain boundaries and the conduction band tail. Oxygen surface termination on the diamond films provides further enhancement of the injected charge per photon, compared to as-grown or hydrogen terminated surfaces. Based on the measured injected charge density, we estimate that the generated photocurrent of oxygen terminated N-UNCD is sufficient to achieve extracellular stimulation of brain tissue within the safe optical exposure limit.

Understanding the effect of host structure of nitrogen doped ultrananocrystalline diamond electrode on electrochemical carbon dioxide reduction

Despite recent literature reporting the remarkable electrochemical CO2 reduction reaction (CO2RR) performance of nitrogen-doped graphitic carbon materials (sp2-carbon) and nitrogen-doped diamond materials (sp3-carbon), no systematic studies have been conducted on the catalytic activities of hybrid carbon nanomaterials between diamond and graphitic extremes. In this study, nitrogen-doped ultra-nanocrystalline diamond thin films were prepared by a microwave-assisted chemical vapor deposition technique. The ratio of sp2-carbon phase to sp3-carbon phase was controlled by varying growth conditions. Our results confirm that nitrogen-doped sp2-carbon (graphitic) rich electrodes have better selectivity for the CO2RR products over the nitrogen-doped sp3-carbon rich electrodes, indicating that the host structure of nitrogen dopants is crucial for the catalytic activity. Nitrogen-doped sp2-carbon electrodes present Faradaic efficiency for CO production up to 82% with excellent activity and selectivity. The vital role of the host structure and the potential catalytic sites were detailed by density functional theory (DFT) calculations.

Characterization and design optimization of heterojunction photodiodes comprising n-type ultrananocrystalline diamond/hydrogenated amorphous carbon composite and p-type Si

In this paper, we characterize and optimize design of a candidate ultraviolet photodiode based on nitrogen-doped ultrananocrystalline diamond hydrogenated amorphous carbon (UNCD/a-C:H) composite films grown on crystalline-Si substrates by coaxial arc plasma deposition. A comprehensive study including growth, fabrication, characterization, and modeling of the photodetector is presented here. The current-voltage characteristics of the device were reproduced and their critical parameters were extracted from a good matching between experimental and simulation results. A midgap acceptor-like defect state density of ~ 5 × 1017 cm−3 eV−1 was found to be the dominant defect in the UNCD/a-C:H film, in addition to an interface defect density of ~ 3 × 1013 cm−2 eV−1 at the interface of the UNCD/a-C:H film and the Si substrate. Experimental and simulation results showed that introducing an intrinsic UNCD/a-C:H layer in a pin heterostructure would significantly reduce the device leakage current and consequently improve its performance as an ultraviolet photodiode. Unoptimized fabricated devices exhibited a room temperature photoresponsivity of 135 mA/W measured under illumination of ultraviolet monochromatic light with a wavelength of 254 nm. The key parameters for optimized design of the device were extracted and investigated in details.

Feasibility of Nitrogen Doped Ultrananocrystalline Diamond Microelectrodes for Electrophysiological Recording From Neural Tissue.

Neural prostheses that can monitor the physiological state of a subject are becoming clinically viable through improvements in the capacity to record from neural tissue. However, a significant limitation of current devices is that it is difficult to fabricate electrode arrays that have both high channel counts and the appropriate electrical properties required for neural recordings. In earlier work, we demonstrated nitrogen doped ultrananocrystalline diamond (N-UNCD) can provide efficacious electrical stimulation of neural tissue, with high charge injection capacity, surface stability and biocompatibility. In this work, we expand on this functionality to show that N-UNCD electrodes can also record from neural tissue owing to its low electrochemical impedance. We show that N-UNCD electrodes are highly flexible in their application, with successful recordings of action potentials from single neurons in an in vitro retina preparation, as well as local field potential responses from in vivo visual cortex tissue. Key properties of N-UNCD films, combined with scalability of electrode array fabrication with custom sizes for recording or stimulation along with integration through vertical interconnects to silicon based integrated circuits, may in future form the basis for the fabrication of versatile closed-loop neural prostheses that can both record and stimulate.

Transient photoresponse of nitrogen-doped ultrananocrystalline diamond electrodes in saline solution

Beyond conventional electrically-driven neuronal stimulation methods, there is a growing interest in optically-driven approaches. In recent years, nitrogen-doped ultrananocrystalline diamond (N-UNCD) has emerged as a strong material candidate for use in electrically-driven stimulation electrodes. This work investigates the electrochemical activity of N-UNCD in response to pulsed illumination, to assess its potential for use as an optically-driven stimulation electrode. Whilst N-UNCD in the as-grown state exhibits a weak photoresponse, the oxygen plasma treated film exhibits two orders of magnitude enhancement in its sub-bandgap open circuit photovoltage response. The enhancement is attributed to the formation of a dense network of oxygen-terminated diamond nanocrystals at the N-UNCD surface. Electrically connected to the N-UNCD bulk via sub-surface graphitic grain boundaries, these diamond nanocrystals introduce a semiconducting barrier between the sub-surface graphitic semimetal and the electrolyte solution, leading to a photovoltage under irradiation with wavelengths of λ = 450 nm and shorter. Within the safe optical exposure limit of 2 mW mm−2, charge injection capacity of 0.01 mC cm−2 is achieved using a 15 × 15 μm electrode, meeting the requirements for extracellular and intercellular stimulation. The nanoscale nature of processes presented here along with the diamond's biocompatibility and biostability open an avenue for the use of oxygen treated N-UNCD as optically driven stimulating electrodes.

Highly conductive nitrogen-doped ultrananocrystalline diamond films with enhanced field emission properties: triethylamine as a new nitrogen source

In this study, triethylamine (TEA) dissolved in the methanol was used as a liquid nitrogen source to synthesize nitrogen-doped ultrananocrystalline diamond (N-UNCD) films on silicon substrates via microwave plasma enhanced chemical vapor deposition (MPCVD).

Electrochemical cathodic treatment: A non-destructive way to hydrogenate conductive ultrananocrystalline diamond films

The excellent conductivity of nitrogen-doped ultrananocrystalline diamond (UNCD) films mainly originates from sp2-bonded carbon located in the grain boundaries. But conventional hydrogen plasma treatment to achieve surface hydrogenation would preferentially etch sp2-bonded carbon and deteriorate the conductivity. In this article, an electrochemical cathodic treatment (ECT) was developed as an alternative method to hydrogenate the surface of nitrogen-doped conductive UNCD films. The treatment was done in acidic solution at −30 V for 10 min. X-ray photoelectron spectroscopy revealed that, after the ECT, the photoelectron subpeaks related to carbon–oxygen bonding significantly decreased and there was no obvious variation in the content of sp2-bonded carbon. Compared to pristine UNCD (P-UNCD) films, the hydrogenated UNCD (H-UNCD) films exhibited a marked change in electrochemical responses such as cyclic voltammetry, capacitance–voltage and electrochemical impedance spectroscopy, suggesting the different surface termination between two UNCD films. More importantly, Raman spectra, scanning electron microscopy and Hall-effect measurement, revealed that no obvious variations in atomic bonds and surface morphology as well as electrical properties existed before and after the ECT. All of these results demonstrated that ECT can be a non-destructive surface hydrogenation method for nitrogen-doped conductive UNCD films with a high content of sp2-bonded carbon atoms.

Strong photoluminescence from N-V and Si-V in nitrogen-doped ultrananocrystalline diamond film using plasma treatment

Raman, photoluminescence, and transport properties of nitrogen-doped ultrananocrystal diamond (UNCD) films were investigated following treatment with low energy microwave plasma at room temperature. The conductivity of nitrogen-doped UNCD films treated by microwave plasma was found to decrease slightly due to the reduced grain boundaries. We speculate that the plasma generated vacancies in UNCD films and provided heat for further mobilizing the vacancies to combine with the impurities, which led to the formation of the silicon-vacancy (Si-V) and nitrogen-vacancy (N-V) defect centers. The generated color centers were found to be distributed uniformly in the samples using a PL mapping technique. The PL emitted by the plasma treated nitrogen-doped UNCD film was strongly enhanced in comparison with the untreated films.