Neck Phantom Research Articles

SU-E-T-110: Development of An Independent, Monte Carlo, Dose Calculation, Quality Assurance Tool for Clinical Trials

Purpose: To develop a comprehensive end-to-end test for Varian's TrueBeam linear accelerator for head and neck IMRT using a custom phantom designed to utilize multiple dosimetry devices. Purpose: To commission a multiple-source Monte Carlo model of Elekta linear accelerator beams of nominal energies 6MV and 10MV. Methods: A three source, Monte Carlo model of Elekta 6 and 10MV therapeutic x-ray beams was developed. Energy spectra of two photon sources corresponding to primary photons created in the target and scattered photons originating in the linear accelerator head were determined by an optimization process that fit the relative fluence of 0.25 MeV energy bins to the product of Fatigue-Life and Fermi functions to match calculated percent depth dose (PDD) data with that measured in a water tank for a 10×10cm2 field. Off-axis effects were modeled by a 3rd degree polynomial used to describe the off-axis half-value layer as a function of off-axis angle and fitting the off-axis fluence to a piecewise linear function to match calculated dose profiles with measured dose profiles for a 40×40cm2 field. The model was validated by comparing calculated PDDs and dose profiles for field sizes ranging from 3×3cm2 to 30×30cm2 to those obtained from measurements. A benchmarking study compared calculated data to measurements for IMRT plans delivered to anthropomorphic phantoms. Results: Along the central axis of the beam 99.6% and 99.7% of all data passed the 2%/2mm gamma criterion for 6 and 10MV models, respectively. Dose profiles at depths of dmax, through 25cm agreed with measured data for 99.4% and 99.6% of data tested for 6 and 10MV models, respectively. A comparison of calculated dose to film measurement in a head and neck phantom showed an average of 85.3% and 90.5% of pixels passing a 3%/2mm gamma criterion for 6 and 10MV models respectively. Conclusion: A Monte Carlo multiple-source model for Elekta 6 and 10MV therapeutic x-ray beams has been developed as a quality assurance tool for clinical trials.

Evaluation of the penetration depth and dose distribution of single energy electrons in the neck phantom using MCNPX code

Evaluation of the penetration depth and dose distribution of single energy electrons in the neck phantom using MCNPX code

Validation of MR thermometry: Method for temperature probe sensor registration accuracy in head and neck phantoms

Purpose: Magnetic resonance thermometry (MRT) is an attractive means to non-invasively monitor in vivo temperature during head and neck hyperthermia treatments because it can provide multi-dimensional temperature information with high spatial resolution over large regions of interest. However, validation of MRT measurements in a head and neck clinical set-up is crucial to ensure the temperature maps are accurate. Here we demonstrate a unique approach for temperature probe sensor localisation in head and neck hyperthermia test phantoms. Methods: We characterise the proton resonance frequency shift temperature coefficient and validate MRT measurements in an oil–gel phantom by applying a combination of MR imaging and 3D spline fitting for accurate probe localisation. We also investigate how uncertainties in both the probe localisation and the proton resonance frequency shift (PRFS) thermal coefficient affect the registration of fibre-optic reference temperature probe and MRT readings. Results: The method provides a two-fold advantage of sensor localisation and PRFS thermal coefficient calibration. We provide experimental data for two distinct head and neck phantoms showing the significance of this method as it mitigates temperature probe localisation errors and thereby increases accuracy of MRT validation results. Conclusions: The techniques presented here may be used to simplify calibration experiments that use an interstitial heating device, or any heating method that provides rapid and spatially localised heat distributions. Overall, the experimental verification of the data registration and PRFS thermal coefficient calibration technique provides a useful benchmarking method to maximise MRT accuracy in any similar context.

EP-1448: Verification of a treatment planning system using an in-house designed head and neck phantom

EP-1448: Verification of a treatment planning system using an in-house designed head and neck phantom

Conversion coefficients for the estimation of effective dose in cone-beam CT

PurposeTo determine the conversion coefficients (CCs) from the dose-area product (DAP) value to effective dose in cone-beam CT.Materials and MethodsA CBCT scanner with four fields of view (FOV) was used. Using two exposure settings of the adult standard and low dose exposure, DAP values were measured with a DAP meter in C mode (200mm×179 mm), P mode (154 mm×154 mm), I mode (102 mm×102 mm), and D mode (51 mm×51 mm). The effective doses were also investigated at each mode using an adult male head and neck phantom and thermoluminescent chips. Linear regressive analysis of the DAP and effective dose values was used to calculate the CCs for each CBCT examination.ResultsFor the C mode, the P mode at the maxilla, and the P mode at the mandible, the CCs were 0.049 µSv/mGycm2, 0.067 µSv/mGycm2, and 0.064 µSv/mGycm2, respectively. For the I mode, the CCs at the maxilla and mandible were 0.076 µSv/mGycm2 and 0.095 µSv/mGycm2, respectively. For the D mode at the maxillary incisors, molars, and mandibular molars, the CCs were 0.038 µSv/mGycm2, 0.041 µSv/mGycm2, and 0.146 µSv/mGycm2, respectively.ConclusionThe CCs in one CBCT device with fixed 80 kV ranged from 0.038 µSv/mGycm2 to 0.146 µSv/mGycm2 according to the imaging modes and irradiated region and were highest for the D mode at the mandibular molar.

Dosimetry in brain tumor phantom at 15 MV 3D conformal radiation therapy

Glioblastoma multiforme (GBM) is the most common, aggressive, highly malignant and infiltrative of all brain tumors with low rate of control. The main goal of this work was to evaluate the spatial dose distribution into a GBM simulator inside a head phantom exposed to a 15 MV 3D conformal radiation therapy in order to validate internal doses. A head and neck phantom developed by the Ionizing Radiation Research Group (NRI) was used on the experiments. Such phantom holds the following synthetic structures: brain and spinal cord, skull, cervical and thoracic vertebrae, jaw, hyoid bone, laryngeal cartilages, head and neck muscles and skin. Computer tomography (CT) of the simulator was taken, capturing a set of contrasted references. Therapy Radiation planning (TPS) was performed based on those CT images, satisfying a 200 cGy prescribed dose split in three irradiation fields. The TPS assumed 97% of prescribed dose cover the prescribed treatment volume (PTV). Radiochromic films in a solid water phantom provided dose response as a function of optical density. Spatial dosimetric distribution was generated by radiochromic film samples at coronal, sagittal-anterior and sagittal-posterior positions, inserted into tumor simulator and brain. The spatial dose profiles held 70 to 120% of the prescribed dose. In spite of the stratified profile, as opposed to the smooth dose profile from TPS, the tumor internal doses were within a 5% deviation from 214.4 cGy evaluated by TPS. 83.2% of the points with a gamma value of less than 1 (3%/3mm) for TPS and experimental values, respectively. At the tumor, measured at coronal section, a few dark spots in the film caused the appearance of outlier points in 13-15% of dose deviation percentage. And, as final conclusion, such dosimeter choice and the physical anthropomorphic and anthropometric phantom provided an efficient method for validating radiotherapy protocols.

Comprehensive quality assurance for base of skull IMRT

Six base of skull IMRT treatment plans were delivered to Presage dosimeters within the RPC Head and Neck Phantom for quality assurance (QA) verification. Isotropic 2mm 3D data were acquired by optical-CT scanning with the DLOS system (Duke Large Optical-CT Scanner) and compared to the Eclipse (Varian) treatment plan. Normalized Dose Distribution (NDD) pass rates were obtained for a number of criteria. High quality 3D dosimetry data was observed from the DLOS system, illustrated here through colormaps, isodose lines, and profiles. Excellent agreement with the planned dose distributions was also observed with NDD analysis revealing > 90% pass rates (with criteria 3%, 2mm), and noise < 0.5%. The results comprehensively confirm the high accuracy of base-of-skull IMRT treatment in our clinic.

A Head and Neck Simulator for Radiology and Radiotherapy

Phantoms are suitable tools to simulate body tissues and organs in radiology and radiation therapy. This study presents the development of a physical head and neck phantom and its radiological response for simulating brain pathology. The following features on the phantom are addressed and compared to human data: mass density, chemical composition, anatomical shape, computerized tomography images and Hounsfield Units. Mass attenuation and kerma coefficients of the synthetic phantom and normal tissues, as well as their deviations, were also investigated. Radiological experiments were performed, including brain tumors and subarachnoid hemorrhage simulations. Computerized tomography images of such pathologies in phantom and human were obtained. The anthropometric dimensions of the phantom present anatomical conformation similar to a human head and neck. Elemental weight percentages of the equivalent tissues match the human ones. Hounsfield Unit values of the main developed structures are presented, approaching human data. Kerma and mass attenuation coefficients spectra from human and phantom are presented, demonstrating smaller deviations in the radiological X-ray spectral domain. In conclusion, the phantom presented suitable normal and pathological radiological responses relative to those observed in humans. It may improve radiological protocols and education in medical imaging.

SU‐E‐J‐215: A Two‐Dimensional Deformable Head and Neck Phantom With In‐Vivo Dosimetry for Adaptive Radiotherapy Verification

Purpose: To design and construct a deformable head and neck (HN) phantom with in‐vivo dosimetry for adaptive radiotherapy (ART) verification purposes. Methods: The two‐dimensional deformable phantom recreates a single CT slice of a HN patient. It consists of two parallel acrylic plates with deformable material sandwiched in between. Gypsum plaster is used for bony anatomy and is rigidly attached to the plates. Soft tissue is mimicked with TX151 solidifying powder mixed with water. Areas of denser tissue are obtained by adding plaster powder into the mixture of TX151 and water. Parotids are represented with properties in between less dense and denser tissue. Tissue is distributed around the bony anatomy and constrained by an elastic rubber band around it. The pharynx is created with a hollow nylon tube. An inflatable silicone balloon filled with diluted barium sulfate acts as tumor. Thin plastic markers are glued on the phantom surfaces adjacent to the clear acrylic plates, providing quantifiable visual information of the deformation. Fixed detector holders are placed inside the cord and near the mandible while holders on rails that move with phantom deformation are placed close to the tumor and inside one parotid. Results: The deformable phantom has been tested for the validation of ART. We have studied the symmetric property and the response of an SRS diode that is used for dose measurements. The four point doses are obtained before and after deformation with the original plan and the re‐plan irradiated. The deformable image registration (DIR) algorithm accuracy is also verified by the deformation ground truth provided by surface markers. Conclusion: We have designed and constructed a deformable and durable HN phantom. This phantom can be used for DIR algorithm accuracy tests as well as ART verification.

Patient‐specific QA for IMRT should be performed using software rather than hardware methods

Suggestions for topics suitable for these Point/Counterpoint debates should be addressed to Colin G. Orton, Professor Emeritus, Wayne State University, Detroit: ortonc@comcast.net. Persons participating in Point/Counterpoint discussions are selected for their knowledge and communicative skill. Their positions for or against a proposition may or may not reflect their personal opinions or the positions of their employers.

Development and evaluation of a Perspex anthropomorphic head and neck phantom for three dimensional conformal radiation therapy (3D-CRT)

AbstractPurposesTo design, construct and evaluate an anthropomorphic head and neck phantom for the dosimetric evaluation of 3D-conformal radiotherapy (3D-CRT) dose planning and delivery, for protocols developed by the Radiation Therapy Oncology Group (RTOG).Materials and methodsAn anthropomorphic head and neck phantom was designed and fabricated using Perspex material with delineated planning target volumes (PTVs) and organs at risk (OARs) regions. The phantom was imaged, planned and irradiated conformally by a 3D-CRT plan. Dosimetry within the phantom was assessed using thermoluminescent dosimeters (TLDs). The reproducibility of phantoms and TLD readings were checked by three repeated identical irradiations. Subsequent three clinical 3D-CRT plans for nasopharyngeal patients have been verified using the phantom. Measured doses from each dosimeter were compared with those acquired from the treatment planning system (TPS).ResultsPhantom's measured doses were reproducible with &lt;3·5% standard deviation between the three TLDs’ repeated measurements. Verification of three head and neck 3D-CRT patients’ plans was implemented, and good agreement between measured values and those predicted by TPS was found. The percentage dose difference for TLD readings matched those corresponding to the calculated dose to within 4%.ConclusionThe good agreement between predicted and measured dose shows that the phantom is a useful and efficient tool for 3D-CRT technique dosimetric verification.

Assessment of the effective doses from two dental cone beam CT devices

This study compares the effective dose for different fields of view (FOVs), resolutions and X-ray parameters from two cone beam CT units: the KaVo 3D (three-dimensional) eXam and the KaVo Pan eXam Plus 3D (KaVo Dental, Biberach, Germany). Measurements were made using thermoluminescent dosemeter chips in a radiation analog dosimetry head and neck phantom. The calculations of effective doses are based on the ICRP 60 and ICRP 103 recommendations of the International Commission on Radiological Protection. Effective doses from the 3D eXam ranged between 32.8 µSv and 169.8 µSv, and for the Pan eXam Plus effective doses ranged between 40.2 µSv and 183.7 µSv; these were measured using ICRP 103 weighting factors in each case. The increase in effective dose between ICRP 60 and ICRP 103 recommendations averaged 157% for all measurements. Effective doses can be reduced significantly with the choice of lower resolutions and mAs settings as well as smaller FOVs to avoid tissues sensitive to radiation being inside the direct beam. Larger FOVs do not necessarily lead to higher effective doses.

Credentialing results from IMRT irradiations of an anthropomorphic head and neck phantom

This study was performed to report and analyze the results of the Radiological Physics Center's head and neck intensity-modulated radiation therapy (IMRT) phantom irradiations done by institutions seeking to be credentialed for participation in clinical trials using intensity modulated radiation therapy. The Radiological Physics Center's anthropomorphic head and neck phantom was sent to institutions seeking to participate in multi-institutional clinical trials. The phantom contained two planning target volume (PTV) structures and an organ at risk (OAR). Thermoluminescent dosimeters (TLD) and film dosimeters were imbedded in the PTV. Institutions were asked to image, plan, and treat the phantom as they would treat a patient. The treatment plan should cover at least 95% of the primary PTV with 6.6 Gy and at least 95% of the secondary PTV with 5.4 Gy. The plan should limit the dose to the OAR to less than 4.5 Gy. The passing criteria were ±7% for the TLD in the PTVs and a distance to agreement of 4 mm in the high dose gradient area between the PTV and the OAR. Pass rates for different delivery types, treatment planning systems (TPS), linear accelerators, and linear accelerator-planning system combinations were compared. The phantom was irradiated 1139 times by 763 institutions from 2001 through 2011. 929 (81.6%) of the irradiations passed the criteria. 156 (13.7%) irradiations failed only the TLD criteria, 21 (1.8%) failed only the film criteria, and 33 (2.9%) failed both sets of criteria. Only 69% of the irradiations passed a narrowed TLD criterion of ±5%. Varian-Elipse and TomoTherapy-HiArt combinations had the highest pass rates, ranging from 90% to 93%. Varian-Pinnacle(3), Varian-XiO, Siemens-Pinnacle(3), and Elekta-Pinnacle(3) combinations had pass rates that ranged from 66% to 81%. The head and neck phantom is a useful credentialing tool for multi-institutional IMRT clinical trials. The most commonly represented linear accelerator-planning system combinations can all pass the phantom, though some combinations had higher passing percentages than others. Tightening the criteria would significantly reduce the number of institutions passing the credentialing criteria. Causes for failures include incorrect data entered into the TPS, inexact beam modeling, and software and hardware failures.

Fast polyenergetic forward projection for image formation using OpenCL on a heterogeneous parallel computing platform

Simulated projection images of digital phantoms constructed from CT scans have been widely used for clinical and research applications but their quality and computation speed are not optimal for real-time comparison with the radiography acquired with an x-ray source of different energies. In this paper, the authors performed polyenergetic forward projections using open computing language (OpenCL) in a parallel computing ecosystem consisting of CPU and general purpose graphics processing unit (GPGPU) for fast and realistic image formation. The proposed polyenergetic forward projection uses a lookup table containing the NIST published mass attenuation coefficients (μ∕ρ) for different tissue types and photon energies ranging from 1 keV to 20 MeV. The CT images of interested sites are first segmented into different tissue types based on the CT numbers and converted to a three-dimensional attenuation phantom by linking each voxel to the corresponding tissue type in the lookup table. The x-ray source can be a radioisotope or an x-ray generator with a known spectrum described as weight w(n) for energy bin E(n). The Siddon method is used to compute the x-ray transmission line integral for E(n) and the x-ray fluence is the weighted sum of the exponential of line integral for all energy bins with added Poisson noise. To validate this method, a digital head and neck phantom constructed from the CT scan of a Rando head phantom was segmented into three (air, gray∕white matter, and bone) regions for calculating the polyenergetic projection images for the Mohan 4 MV energy spectrum. To accelerate the calculation, the authors partitioned the workloads using the task parallelism and data parallelism and scheduled them in a parallel computing ecosystem consisting of CPU and GPGPU (NVIDIA Tesla C2050) using OpenCL only. The authors explored the task overlapping strategy and the sequential method for generating the first and subsequent DRRs. A dispatcher was designed to drive the high-degree parallelism of the task overlapping strategy. Numerical experiments were conducted to compare the performance of the OpenCL∕GPGPU-based implementation with the CPU-based implementation. The projection images were similar to typical portal images obtained with a 4 or 6 MV x-ray source. For a phantom size of 512 × 512 × 223, the time for calculating the line integrals for a 512 × 512 image panel was 16.2 ms on GPGPU for one energy bin in comparison to 8.83 s on CPU. The total computation time for generating one polyenergetic projection image of 512 × 512 was 0.3 s (141 s for CPU). The relative difference between the projection images obtained with the CPU-based and OpenCL∕GPGPU-based implementations was on the order of 10(-6) and was virtually indistinguishable. The task overlapping strategy was 5.84 and 1.16 times faster than the sequential method for the first and the subsequent digitally reconstruction radiographies, respectively. The authors have successfully built digital phantoms using anatomic CT images and NIST μ∕ρ tables for simulating realistic polyenergetic projection images and optimized the processing speed with parallel computing using GPGPU∕OpenCL-based implementation. The computation time was fast (0.3 s per projection image) enough for real-time IGRT (image-guided radiotherapy) applications.

A phantom study to determine the optimum size of a single collimator for shortening the treatment time in CyberKnife stereotactic radiosurgery of spherical targets

Prolonged treatment execution time is a concern in CyberKnife robotic radiosurgery. Beam reduction and node reduction technique, and monitor unit optimization methods are adopted to reduce the treatment time. Usage of single collimator in the CyberKnife treatment plan can potentially reduce collimator exchange time. An optimal single collimator, which yields an acceptable dose distribution along with minimum number of nodes, beams, and monitor units, can be a versatile alternative for shortening treatment time. The aim of the present study is to find the optimal single collimator in CyberKnife treatment planning to shorten the treatment time with the acceptable dose distribution. A spherical planning target volume PTV1 was drawn in an anthropomorphic head and neck phantom. Plans with same treatment goals were generated for all the 12 collimators independently. D95% was selected as the prescribing isodose and the prescribed dose was 10 Gy. The plan of the optimal collimator size was evaluated for conformity, homogeneity, and dose spillage outside the target. The optimum collimator size and the target dimensions were correlated. The study was repeated with two other target volumes PTV2 and PTV3 for generalizing the results. Collimator sizes just above the diameter of the spherical PTVs were yielding least number of nodes and beams with acceptable dose distributions. The collimator size of 35 mm is optimum for the PTV1, whose diameter is 31.4 mm. Similarly, 50 mm collimator is optimum for PTV2 (diameter=45.2 mm) and 20 mm collimator is optimum for PTV3 (Diameter=17.3 mm). The total number of monitor units is found to reduce with increasing collimator size. Optimal single collimator is found to be useful for shortening the treatment time in spherical targets. Studies on two clinical targets, (a brain metastasis and a liver metastasis cases) show comparable results with the phantom study.PACS numbers: 87.55.D, 87.55.de, 87.53.Ly, 87.55.kh, 87.56.nk, 87.55.ne, 87.55.‐x

Increased vessel depiction of the carotid bifurcation with a specialized 16‐channel phased array coil at 3T

The purpose of this work was to design and construct a multichannel receive-only radiofrequency coil for 3T magnetic resonance imaging of the human carotid artery and bifurcation with optimized signal-to-noise ratio (SNR) in the carotid vessels along the full extent of the neck. A neck phantom designed to match the anatomy of a subject with a neck representing the body habitus often seen in subjects with carotid arterial disease was constructed. Sixteen circular coil elements were arranged on a semirigid fiberglass former that closely fit the shape of the phantom, resulting in a 16-channel bilateral phased array coil. Comparisons were made between this coil and a typical 4-channel carotid coil in a study of 10 carotid vessels in five healthy volunteers. The 16-channel carotid coil showed a 73% average improvement in SNR at the carotid bifurcation. This coil also maintained an SNR greater than the peak SNR of the 4-channel coil over a vessel length of 10 cm. The resulting increase in SNR improved vessel depiction of the carotid arteries over an extended field of view, and demonstrated better image quality for higher parallel imaging reduction factors compared to the 4-channel coil.

B-Spline Registration Based on New Concept of an Intelligent Masking Procedure and GPU Computations for the Head and Neck Adaptive Tomotherapy

The deformable image registration (DIR) procedure has been optimized for helical tomotherapy. The data on registration shifts obtained on matching planning image with pre-treatment megavoltage CT are used in our software for acceleration of the first step (rigid registration) of the DIR procedure and for implementation of the B-Spline algorithm with intelligent masking. Priorities of the masks were automatically calculated based on disagreement detected during rigid registration. Evaluation tasks included: (a) comparison of accuracy and rate for schemes of pre-registered and non-registered images; (b) qualification of the effectiveness of the intelligent masking process, and (c) determination of acceleration of achievable with GPU computing. A specially designed head and neck phantom used for evaluation included structures with controlled changes of position, volume, density, and shape. Re-contouring procedures were performed with an Adaptive Planning software (Tomotherapy Inc.). No statistical difference was observed in accuracy of DIR based on structure position match on the tomotherapy unit and non pre-registered images (p > 0.7). Using pre-registered data reduces the total time required for execution of the elastic registration procedure by 5%. These data are also necessary for intelligent masking procedure during B-Spine registration. Intelligent masking procedure increases accuracy of the registration for a masked structure (p < 0.04) without decreasing the accuracy in non-masked tissues and additionally reduces the total time by 13%. GPU computations speed up procedure 30 times. GPU computing of the DIR in current status of our investigation could be realized in a relatively short time after pre-treatment imaging. The proposed approach can be used in the routine assessment of anatomic changes occurring in healthy tissue during the course of radiotherapy. Further developments will be concentrated on the full integration of DIR computations in the imaging and treatment process of helical tomotherapy.

SU-E-T-603: Influence of PTV Delineation at Air Cavity Interface on Tomotherapy Plan Quality.

To determine if different ways in PTV delineation at an air cavity interface yield differences in overall plan quality and treatment efficiency Methods: Three different PTVs were used for treating a patient whose CTV surrounded a large air cavity created by a resected hard palate. The CTV lined the surface of the air cavity while PTV1 included the entire air cavity, PTV2 extended 4mm from the surface of the cavity into air, and PTV3 was reduced 4mm within the surface of the cavity. Tomotherapy plans were generated for all three PTVs. During each planning, all constraints to target and normal structures were kept constant along with the number of optimizations. Same planning process was repeated on a head and neck digital phantom with mock target, normal structures and cavity. Three treatment planning approaches showed no significantly different target coverage in terms of minimum or maximum dose to their respective PTVs. All plans attained 95% coverage of the CTV and PTV by 100% of the prescription. The conformity index (CI) of the plans delivered to PTV1, PTV2, and PTV3 were 1.09, 1.11, and 1.18, respectively. The skin, optic nerves, brainstem and spinal cord all received similar maximum dose to their respective volumes for each plan within 1Gy. The monitor units required for each treatment plan were all within 6% of one another with PTV1 having the highest. For head and neck phantom, the CIs of three plans were 1.05, 1.21, and 1.18, respectively. The coverage of the phantom CTV and sparing of normal structures were nearly equivalent. The total treatment times were identical. Tomotherapy planning is able to deliver dose to a head and neck PTV containing a large air cavity without compromising target coverage, sparing of normal tissues, or delivery time.

SU-E-T-554: PTV to Skin Proximity for Head and Neck IMRT Treatment Planning.

The goal of this work was to evaluate measured vs. calculated surface dose as a function of PTV-to-skin proximity and calculation matrix oxel size, determine effects on plan quality, and provide parameters and levels of uncertainty for clinical use. A right-sided CTV with the lateral border 5mm from the surface was delineated on the CT data of a head and neck phantom. A 5mm PTV was generated except laterally where distances of 0-5mm were used. A 7-field IMRT plan was generated using the Eclipse TPS. Optimization was performed where 95% of the PTV receives the prescription dose using a matrix size of 2mm3 . Dose calculations were repeated for grid sizes of 1, 3 and 5mm3 . For each plan nine point dose values were obtained just inside the phantom surface, corresponding to a 2cm2 grid near the central target region. Nine ultra-thin TLDs were placed on the phantom surface corresponding to the grid. Measured and calculated dose values were compared. Conformality, homogeneity and target coverage were compared. Surface dose is over-estimated by the TPS by 21 and 8% for 5 and 3mm3 voxels, respectively and accurately predicted for 2mm3 voxels. A voxel size of 1mm3 results in underestimation of 13%. Conformality improves with increasing PTV to skin distance and a CI of unity results for grid sizes of 1-3mm3 between 4 and 4.5mm. Hot spot decreases as the PTV moves away from the surface and falls below 110% at 4mm. Underdosage worsens as the PTV approaches the skin. For decreasing PTV-to-skin distance with this TPS, isodose conformality decreases, 'hot spot' increases, and target coverage degrades. Surface dose is accurately predicted for a 2mm3 voxel size, while choosing a finer or coarser grid results in underestimation or overestimation, respectively. All of the above appear to hold for VMAT.

SU-E-J-74: Evaluation of the Commercial Prototype Open Face Mask Used with Surface Rendering Imaging System for Proton Therapy Patients with Cancers of the Brain and Head: Successful Preclinical Study.

Evaluation of the commercial prototype open face mask (Fibreplast, Q-FixTM) used with surface rendering imaging system (AlignRTTM, London, UK) for setup and monitoring of proton therapy patients with cancers of the brain and head. Fibreplastic open face masks were used with Base-of-Skull frame/moldcare pillow. Two sizes of the pre-made cutouts in the masks were investigated: leaveing open skin surface in the oval-shaped area between (I) upper lip and forehead boss, II) between mandible and forehead boss in superior-inferior direction; and between zygomatic (cheek-) bones/sphenoid bones laterally. Calibration of AlignRT system was verified with SRS cube phantom (VisionRT)and 2D X-ray patient positioning system (DIPS, IBA). The accuracy of translational shifts and rotations was a) verified using a head&neck phantom and b) tested using volunteers. Within AlignRT software, only the open area was used as ROI for the registration; the option 'Intracranial SRS' used for surface capture. For the isocenter determination accuracy within 0.3mm/0.2 degrees, the head&neck phantom registration was performed with the 0.5mm/0.5 degree accuracy; the volunteer tests showed the registration accuracy within 0.5mm ±0.2mm (1 s)/0.7±0.2 (1 s) degree. The simulation of the noise in the surface data such as eye blinking and attempts to swallow/chew was performed, with negligible effect on the registration. No significant differences between the study results between the masks of type (I) and (II) were noticed. The AlignRT surface rendering system has sufficient accuracy when used with the open face head&neck mask for localization/registration of the proton therapy patients with tumors of the head and brain.