Natural Reinforcement Research Articles

Ecofriendly hybrid natural fiber reinforced polypropylene composites from biowastes

The used ground coffee waste (GCW) and tea leaf waste (TLW), the large wastes from the beverage process, were selected as natural reinforcement and natural pigment in the polypropylene (PP) matrix. In this work, the maleic anhydride polypropylene (MAPP) was added to the composites to develop the compatibility between fillers, fibers, and polymer matrix. The TLW/PP composites, GCW/PP composites, and GCW/TLW/PP hybrid composites were prepared in the ratio of TLW and GCW ranging from 0 to 30 wt% with the addition of MAPP at 5 wt% of fillers. The presence of GCW and TLW in the PP matrix decreased tensile properties and impact resistance but increased flexural modulus and hardness of PP at high concentrations of GCW and TLW. The increase in GCW and TLW concentration slightly reduced melting temperature but it enhanced the tensile and flexural modulus. Furthermore, it enhanced the hardness, thermal and rheological properties of the composites. The TLW/PP composites had better mechanical properties, and rheological properties than GCW/PP composites but thermal properties were quite similar. The mechanical properties of GCW/TLW/PP hybrid composites were better than those of GCW/PP composites but lower than those of TLW/PP composites. The rheological and thermal behaviour of hybrid composites were like that of TLW/PP composites. Incorporating MAPP improves the mechanical and rheological behavior of PP composites by enhancing the interaction among PP, GCW, and TLW. However, this addition does not significantly enhance the composites’ thermal properties. The optimum composite was hybrid composites of GCW/TLW/PP consisting of GCW of 10 wt%, TLW of 20 wt%, and MAPP of 1.5 wt% which presented good mechanical, thermal, and rheological properties. The mechanical properties of this hybrid composites were as follows: a tensile strength of 26.35 MPa, elongation at break of 10.91%, tensile modulus of 636.69 MPa, flexural strength of 45.57 MPa, flexural modulus of 3632.86 MPa, impact resistance of 12.72 kJ/m2, and a Shore D hardness of 76.15. The overall results showed that GCW and TLW can be used as reinforcement material and natural pigment in the polymer matrix.

Review of Wear and Mechanical Characteristics of Al-Si Alloy Matrix Composites Reinforced with Natural Minerals

Al-Si alloys are vital in the aerospace and automotive industries due to their high strength-to-weight ratio, excellent ductility, and superior corrosion resistance. These properties, along with good thermal conductivity, low thermal expansion, and enhanced wear resistance due to silicon, make them ideal for lightweight, high-performance components like engine parts exposed to harsh conditions and thermal cycling. In recent years, the development of aluminium metal matrix composites using Al-Si alloys as the base material has gathered significant attention. These composites are engineered by integrating various reinforcing particles into the aluminium matrix, which results in remarkable improvements in the wear resistance, hardness, and overall mechanical performance of the material. The stir casting process, a well-established and cost-effective method, is frequently employed to ensure a uniform distribution of these reinforcing particles within the matrix. This review delves into the influence of different types of reinforcing particles on the properties of Al-Si alloy-based AMCs. The incorporation of these reinforcements has been shown to significantly enhance wear resistance, reduce friction, and improve the overall strength and toughness of the composites, making them ideal candidates for high-performance applications in the automotive and aerospace sectors. Moreover, this review highlights the challenges associated with the fabrication of these composites, such as achieving a homogeneous particle distribution and minimizing porosity. It also discusses the latest advancements in processing techniques aimed at overcoming these challenges. Additionally, this review addresses the potential environmental and economic benefits of using natural reinforcements, which not only reduce material costs but also contribute to sustainable manufacturing practices.

Biomimetic Modular Honeycomb with Enhanced Crushing Strength and Flexible Customizability.

The integration of biomimetic principles into the sophisticated design of honeycomb structures has gained significant traction. Inspired by the natural reinforcement mechanisms observed in tree stems, this research introduces localized thickening to the conventional honeycombs, leading to the development of variable-density honeycomb blocks. These blocks are strategically configured to form modular honeycombs. Initially, the methodology for calculating the relative density of the new design is meticulously detailed. Following this, a numerical model based on the plastic limit theorem, verified experimentally, is used to investigate the in-plane deformation models of modular honeycomb under the low- and high-velocity impact and to establish a theoretical framework for compressive strength. The results confirm that the theoretical predictions for crushing strength in the modular honeycomb align closely with numerical findings across both low- and high-velocity impacts. Further investigation into densification strain, energy absorption, and gradient strategy is conducted using both simulation and experimental approaches. The outcomes indicate that the innovative design outperforms conventional honeycombs by significantly enhancing the crushing strength under low-velocity impacts through the judicious arrangement of honeycomb blocks. Additionally, with a negligible difference in densification strains, the modular honeycomb demonstrates superior energy dissipation capabilities compared to its conventional counterparts. At a strain of 0.85, the modular honeycomb's energy absorption capacity improves by 36.68% at 1 m/s and 25.47% at 10 m/s compared to the conventional honeycomb. By meticulously engineering the arrangement of sub-honeycombs, it is possible to develop a modular honeycomb that exhibits a multi-plateau stress response under uniaxial and biaxial compression. These advancements are particularly beneficial to the development of auto crash absorption systems, high-end product transportation packaging, and personalized protective gear.

Impact of different parameters in tribological properties of enset ventricosum/ terminalia arjuna fibers /SiO2 filler incorporation

Natural fiber composites have garnered considerable interest in recent years as sustainable substitutes for synthetic materials, owing to their environmental advantages, including renewability, biodegradability, and cost-effectiveness. Notwithstanding these benefits, there is a vital need to improve the mechanical and tribological characteristics of these composites for applications involving significant wear. This work used compression molding to make hybrid composites with natural fibers (NFs) and nano silicon dioxide (nSiO2) filler. The matrix material was epoxy, and the natural reinforcements were Enset ventricosum (EV) and Terminalia arjuna (TA) fibers. Tensile (TS), flexural (FS), and impact (IS) characteristics improved using 1:1 SiO2 filler and EV/TA fiber reinforcement. The combination of 6 wt% SiO2 and 45 wt% EV/TA improved mechanical performance. A high SiO2 filler (6 wt%) in polymer-based composites decreased Specific Wear Rate (SWR), according to Taguchi optimization. A better fiber-matrix interaction improves the mechanical characteristics of materials with fillers. This study optimized several responses using the new combined compromise solution (CoCoSo) method. Multi-criteria decision making is used here. This study introduces Method based on the Removal Effects of Criteria (MEREC) to determine objective criteria weights. Conclusions from experiments show ideal results. CoCoSo's optimization study showed that Enset ventricosum and Terminalia arjuna fiber (EV/TA) hybridization affected composites' tribological behavior.This hybrid fiber combination carried the most influence, followed by fillers. The optimal results were obtained with 6 wt% SiO2/25 wt% EV/TA Hybrid fiber, 1000 m Sliding distance (SD), 2 m/s Sliding speed (SS), and 10 N axial load (AL).

Development of Natural Fiber Reinforced Polymer Matrix Composites: A Critical Review

AbstractFiber reinforced composites are made by reinforcing fibers in a polymeric matrix and shaping them to fit. Natural fibers, on the other hand, such as jute sisal, hemp, flax etc. are increasingly commonly utilized as reinforcements and perform similarly to artificial fibers. Man‐made fibers like as carbon, glass, and kevlar are utilized as reinforcements in the start and have shown to be the best in terms of characteristics, reinforcing capacity, and usefulness. Research investigations also show that when man‐made and natural reinforcements are combined in a hybrid form, the composite characteristics increase significantly. The composite material obtains all of the better qualities of individual fibers as a result of this combination, and when the composite is subjected to varying loads, each fiber gives its own maximal resistance. The chemical and physical properties are further enhanced by including particular reinforcements into polymer matrix composites, which provide whole new features (which has transformed the aerospace, marine, defence, and automobile industry). As a result, the composite would be better in all attributes. The current study provides a thorough examination of the different challenges concerning the synthesis and mechanical characterization of natural fiber reinforces hybrid polymer composites. Future difficulties, as well as areas of use for polymer matrix composites, have been investigated that may aid in the elimination of plastic waste and the reduction of environmental pollution.

Physico-Thermal and Mechanical Characterization of Alfa Fiber/Polypropylene Composites: Effects of Fiber Treatment and MAPP Compatibilization

ABSTRACT This study investigates the enhancement of compatibility between natural reinforcement materials and polymer matrices, with a focus on Alfa fibers polypropylene (PP) composites. Composites Alfa fibers/PP are prepared using untreated and treated alfa fibers and with or without the addition of a MAPP compatibilizing agent. Firstly, Alfa fibers extracted from the plant are categorized into two groups: untreated and treated with a 3% (wt/v) alkaline solution followed by bleaching. This chemical treatment significantly increases the cellulose content and crystallinity index of the fibers, with improvements of 39.7% and 13.6%, respectively. Secondly, the study incorporates 5 wt% MAPP in the PP matrix as a compatibilizer. The composites produced with 30 wt% of alfa fibers are processed using a single screw extruder, followed by injection molding. Composites samples obtained are characterized using various methods. Thermal analysis reveals that the incorporation of chemically treated alfa fibers along with MAPP significantly accelerates the crystallization rate of the PP matrix, indicating the fibers’ role as effective nucleating agents. Mechanical testing shows marked improvements in the Young’s modulus and tensile strength of the composites obtained with treated alfa fibers reinforcing the MAPP-PP matrix, with increases of 1.67% and 4.61% over their untreated counterparts, respectively.

Enhancing Fatigue Resistance of Polylactic Acid through Natural Reinforcement in Material Extrusion.

This research paper aims to enhance the fatigue resistance of polylactic acid (PLA) in Material Extrusion (ME) by incorporating natural reinforcement, focusing on rotational bending fatigue. The study investigates the fatigue behavior of PLA in ME, using various natural fibers such as cellulose, coffee, and flax as potential reinforcements. It explores the optimization of printing parameters to address challenges like warping and shrinkage, which can affect dimensional accuracy and fatigue performance, particularly under the rotational bending conditions analyzed. Cellulose emerges as the most promising natural fiber reinforcement for PLA in ME, exhibiting superior resistance to warping and shrinkage. It also demonstrates minimal geometrical deviations, enabling the production of components with tighter dimensional tolerances. Additionally, the study highlights the significant influence of natural fiber reinforcement on the dimensional deviations and rotational fatigue behavior of printed components. The fatigue resistance of PLA was significantly improved with natural fiber reinforcements. Specifically, PLA reinforced with cellulose showed an increase in fatigue life, achieving up to 13.7 MPa stress at 70,000 cycles compared to unreinforced PLA. PLA with coffee and flax fibers also demonstrated enhanced performance, with stress values reaching 13.6 MPa and 13.5 MPa, respectively, at similar cycle counts. These results suggest that natural fiber reinforcements can effectively improve the fatigue resistance and dimensional stability of PLA components produced by ME. This paper contributes to the advancement of additive manufacturing by introducing natural fiber reinforcement as a sustainable solution to enhance PLA performance under rotational bending fatigue conditions. It offers insights into the comparative effectiveness of natural fibers and synthetic counterparts, particularly emphasizing the superior performance of cellulose.

Characterization of reinforcing polymeric material with recycled sugarcane bagasse wastes as fiber natural reinforcement

Characterization of reinforcing polymeric material with recycled sugarcane bagasse wastes as fiber natural reinforcement

Testing and Evaluation of Hybrid Polymer Composites Reinforced with Moringa oleifera and Boehmeria nivea Fibers, Embedded with Copper Oxide Particulates, for Thermal, Structural, and Biological Properties

Abstract The increasing need for sustainable materials in industrial applications has prompted a significant shift in attention from synthetic to natural fibers. This study examines the problems and opportunities arising from the utilization of natural fiber-reinforced polymer composites in several industrial sectors. The objective of this work is to fabricate a hybrid composite using a conventional hand layup technique with natural reinforcement of Moringa oleifera (MO) and ramie (Boehmeria nivea) fibers, an epoxy matrix blended with copper oxide filler, utilized to enhance material stability and antimicrobial activity. To quantify the effect of five different weight fractions of MO and ramie fibers on this hybrid composite, its mechanical, thermal, functional, and antifungal properties were examined. The superior tensile strength (61.34 MPa), flexural strength (64.78 MPa), and impact energy (23 J) results indicate that ramie fiber loading should be increased. Additionally, enhanced thermal properties such as thermal conductivity (0.93 W/mK), heat deflection temperature (97°C), thermal expansion coefficient (1.7210−5/°C), and maximal thermal stability were observed at 347°C as a result of the increased ramie fiber loading. This analysis demonstrates that this hybrid composite possesses the antifungal activity necessary to form an inhibition zone against Candida albicans. Scanning electron microscopy analysis was conducted to determine the hybrid composites’ bonding strength and failure mode.

Parent-Mediated Behavioural Intervention in Children with Autism Spectrum Disorder: A Scoping Review

ABSTRACT Children with autism spectrum disorder (ASD) exhibit deficits in social interaction and communication, show repetitive behaviours, and have restricted interests. They are at high risk of developing challenging behaviours, which can hinder social relationships, academic achievement, language skills, overall adaptive development, and also increase the risk of abuse in educational settings. This scoping review addresses the limited focus on parent-mediated behavioural intervention (PMBI) for managing challenging behaviours in children with ASD. Using the Arksey and O’Malley scoping review framework, we retrieved articles published between 2011 and 2022 from SCOPUS, ERIC, and SAGE Publications. Twelve articles met the inclusion criteria. Five themes emerged from the review regarding parents adopting PMBI: (1) performing functional behaviour analysis and developing behaviour intervention plans; (2) applying modification strategies and techniques of antecedent, behaviours and consequence; (3) establishing parent-child secure attachment relationship with child’s lead, positive and natural reinforcement; (4) decreasing child’s challenging behaviours; (5) improving child’s compliance, social responsiveness, and prosocial behaviours. The findings highlight parents as primary intervention agent, emphasising the importance of parental involvement in supporting their child’s development. This review suggests developing cost-effective parent education training programmes to support PMBI as part of comprehensive interventions for children with ASD.

Characterizing Cryptostegia grandiflora stem fiber for reinforcing lightweight polymer composites: A comprehensive study of its physical, chemical, and thermal properties

This study aimed to characterize Cryptostegia grandiflora stem fiber (CGSF) as a potential reinforcement material for lightweight polymer composites. Natural fiber-reinforced materials have gained attention as a promising alternative to synthetic fibers due to their comparable strength and modulus, and lack of harmful chemicals. The physical, chemical, and thermal properties of CGSF were investigated through fiber roughness, chemical measurement, physical measurement, Fourier transform infrared spectroscopy, XRD, water absorption, thermogravimetric analysis, and SEM conformation analysis. The results showed that CGSF has a high cellulose content (80.3 wt.%) and specific strength, making it suitable for use in polymer composites. Its flaky layered outer surface provides a high modulus, and its low microfibril angle observed through electron microscopy results in strong bonding qualities. The fiber also demonstrated improved heat stability up to 254–387 °C through thermogravimetric analysis, meeting the requirements for polymerization. These findings demonstrate the potential of CGSF as a natural reinforcement material for lightweight polymer composites.

A Concise Review of the Components and Properties of Wood-Plastic Composites.

This article summarizes findings in the field of the history, composition, and mechanical properties of WPCs (wood-plastic composites) formed by combining two homogeneous substances, i.e., a polymer matrix with cellulose fibers in a certain ratio (with the addition of additives). In relation to a wide range of applied natural reinforcements in composites, it focuses on wood as a fundamental representative of lignocellulosic fibers. It elucidates the concept of wood flour, the criteria for its selection, methods of storage, morphological characteristics, and similar aspects. The presence of wood in the plastic matrix reduces the material cost while increasing the stiffness. Matrix selection is influenced by the processing temperature (Tmax = 200 °C) due to the susceptibility of cellulose fibers to thermal degradation. Thermoplastics and selected biodegradable polymers can be applied as matrices. The article also includes information on applied additives such as coupling agents, lubricants, biocides, UV stabilizers, pigments, etc., and the mechanical/utility properties of WPC materials. The most common application of WPCs is in automotive sector, construction, aerospace, and structural applications. The potential biodegradability and lower cost of applications featuring composite materials with natural reinforcements motivated us to delve into this type of work.

Investigation of Carbon Fiber Reinforced Polymer Concrete Reinforcement Ageing Using Microwave Infrared Thermography Method

This study presents the utilization of the microwave infrared thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite reinforcement of concrete specimens. At first, a set of numerical models was created, comprising the broadband pyramidal horn antenna and the analyzed specimen. The utilization of the system operating at a power of 1000 W in a continuous mode, operating at frequency of 2.45 GHz, was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer and, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and the CFRP within the adhesive layer. In the modeling stage, the study investigated three separate scenarios—a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte—to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from numerical modeling. In the experiments, the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These conclusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Effect of Reinforcement Ratio and Particle Size on the Physical and Mechanical Performance of Epoxy Matrix Panels and Waste Wood from Iroko Chlorophora excelsa from Cameroon

The use of local materials developed from natural reinforcements remains a major challenge for many researchers in the development of the industry and the fight against pollution. The wood industry generates large quantities of environmental waste, including Iroko wood. To give Iroko a second life, this study uses Iroko sawdust waste to make an epoxy matrix composite material. The composite was produced using a cold pressing technique based on moving the top and bottom plates to a thickness of 10 mm. On this basis, three particle sizes [t < 0.35[, [0.35–0.63[, and [0.63–1[ were used, as well as three reinforcement (R)/matrix (M) percentages of 50R/50M, 60R/40M, and 70R/30M, where R is the reinforcement percentage and M is the matrix percentage. The physical tests, apparent and real density, porosity, moisture content, water absorption rate, absorption and desorption kinetics, diffusion theory, and activation energy were determined by the gravimetric method. A three-point bending test was carried out in accordance with the ASTM D790 for mechanical tests. The results show that the addition of Iroko particles lightens the material by reducing its density. The hydrophilic nature of Iroko particles increases the absorption rate and porosity, with good diffusion capacity as the particle size and percentage increase. The material produced can be light and porous, with possible applications in thermal insulation. In terms of kinetics, Verma et al.’s model best correlates the experimental desorption points for the 3 isotherms, while Page’s model best correlates the water absorption points. The mechanical results show that Young’s modulus and stress at break decrease with an increase in the reinforcement percentage and particle size. The mechanical results can be used to define the material’s applications in construction and furniture. In accordance with the EN312 standard, the composites produced can be classified as type 2 lightweight materials, suitable for use in dry and damp areas.

Physicomechanical, water absorption and thermal properties and morphology of Paederia foetida fiber–Al2O3 powder hybrid‐reinforced epoxy composites

AbstractHybridization of natural fibers with ceramic materials for reinforcing composites allows the optimization of the properties of these materials. For this reason, the present study aims to investigate physical, mechanical, water absorption, swelling and thermal properties as well as morphological characteristics of a hybrid Paederia foetida fibers–alumina powder (PFs–Al2O3)‐reinforced epoxy composite. Epoxy resin served as the matrix, while PFs and Al2O3 were employed as reinforcement. Five types of composites were fabricated using the hot‐pressing technique. The corresponding ratios of PFs:Al2O3 volume fractions (%) considered here were 0:40 (SFA), 10:30 (SFB), 20:20 (SFC), 30:10 (SFD) and 40:0 (SFE). The results reveal that the density of the hybrid PFs–Al2O3 composites decreased for increasing volume fractions of PFs: from 2.173 g cm−3 of SFA to 1.042 g cm−3 of SFE. The highest values of tensile strength (i.e. 49.085 MPa), tensile elastic modulus (i.e. 1.431 GPa) and impact strength (24 kJ m−2) were obtained for the SFD composite material with 30% volume fraction of PFs and 10% volume fraction of Al2O3: this happened because interface bonds between PFs, Al2O3 and epoxy phases achieved their optimal configuration. Overall, mechanical properties of the hybrid PFs–Al2O3‐reinforced epoxy composites were superior to those of composites reinforced only by PF fibers or only by Al2O3. Water absorption and swellability reached their maximum values at the steady state occurring after tested samples remained immersed in water for 820 h. The SFE composite reinforced only by PFs presented the highest water absorption and swelling (i.e. 6.034% and 5.81%, respectively) while for all other hybrid composites (SFD, SFC and SFB) these two quantities remained below 5%. Density and volume fraction of voids of hybrid PFs–Al2O3‐reinforced composites were consistent with the corresponding properties of the composites reinforced only by Al2O3 or PFs. SFD was also the most thermally stable material. Scanning electron microscopy observations of fractured surfaces indicated that the microstructure of the PFs–Al2O3‐reinforced epoxy composites presents several voids, fiber pullouts and transverse fibers, which together optimize the mechanical response of the composite material. Remarkably, the SFD composite material was highly competitive with the most recently developed hybrid composites employing natural reinforcements. © 2024 Society of Industrial Chemistry.

A Pilot Randomized Controlled Trial of Motivation-Based Social Skills Group Treatment with Parent Training.

Despite the popularity of social skills groups, there remains a need for empirical investigation of treatment effects, especially when targeting pivotal aspects of social functioning such as initiations to peers. The goal of the present study was to conduct a randomized controlled trial of a 12-week social intervention (SUCCESS), which combined an inclusive social group with a parent education program. Twenty-five 4- to 6-year-olds with Autism Spectrum Disorder (ASD) were randomized to SUCCESS (N = 11) or to treatment as usual (N = 14). Combining a peer group model with a parent training program, the SUCCESS intervention used naturalistic behavioral techniques (e.g., environmental arrangement, natural reinforcement) to increase social initiations to peers. After 12 weeks, children participating in the SUCCESS program made more frequent initiations to peers than children in the treatment-as-usual group, including more prompted and unprompted initiations to request. Additional gains in clinician-rated social functioning were observed in children randomized to SUCCESS, while differential treatment effects were not detected in parent-rated measures. However, lower baseline social motivation was associated with greater parent-reported initiation improvement. This study provides preliminary support for the efficacy of a naturalistic, behavioral social skills intervention to improve peer initiations for children with ASD. The findings suggest that using a motivation-based social skills group was effective in increasing both prompted and spontaneous initiations to peers, and highlights the need for further research into the role of baseline social motivation in predicting social skills treatment response.

3D printing polypropylene composites reinforced with functionalized halloysite: Balance between stiffness and impact resistance

AbstractIn this work, a new nano‐reinforced polypropylene filament was produced and fabricated by 3D printing to create a nanocomposite with a good balance between stiffness and impact resistance properties. Nanocomposite filament with 0.5, 1.0, and 1.5 wt% of functionalized halloysite nanotubes was prepared. The chemical modification was carried out to obtain a reinforcement that could act as an improved β‐nucleating agent and characterized by infrared spectroscopy. The spectrum showed the appearance of two new bands at 1571 and 1410 cm−1, which could indicate an interaction between the pimelic acid molecules and the oxygenated surface of the halloysite nanotubes. Energy dispersive X‐ray spectroscopy analysis confirmed a good dispersion of the modified reinforcement along the surface of the nanocomposite filament. Wide‐angle X‐ray scattering and differential scanning calorimetry analyses showed the improvement of the β‐nucleating ability of the halloysite nanotubes through new chemically functionalized, obtaining percentages of β‐crystal of 80% for the nanocomposite reinforced with 0.5 wt%. The dynamic mechanical analysis showed that the 3D‐printed functionalized nanocomposites presented higher storage and loss modulus (an increase of 148% and 122%, respectively). Finally, the impact strength properties increased by 90%, 108%, and 21% for the functionalized nanocomposites with 0.5, 1.0, and 1.5 wt%, respectively.Highlights Chemical functionalization of a natural reinforcement as a ‐nucleating agent. 3D printing polypropylene nanocomposites with enhanced properties. Good balance between impact and stiffness properties of nanocomposites.

Pengaruh Penambahan Serat Kulit Jagung Terhadap Sifat Mekanik Komposit Polipropilena (PP) dengan Penambahan Aluminium Oksida (Al2O3) dan Maleat Anhidrida (MAH) sebagai Coupling Agent

The utilization of polymer composites in the automotive field is expanding due to their characteristics such as strength, stiffness, and light weight. Polypropylene (PP) is one of the thermoplastic polymers widely used in composite manufacturing due to its lightweight, corrosion-resistant, and recyclable properties. However, to improve its mechanical properties, modifications using natural reinforcements and coupling agents continue to be made. Corn husk fiber is a natural resource that has potential as a natural reinforcement in polymer composites, it has the advantages of good tensile strength, light weight, and is biodegradable. The addition of Aluminium Oxide (Al2O3) and Maleic Anhydride (MAH) as coupling agent can improve the adhesion between fiber and polymer matrix, support more even load distribution, and optimize the mechanical properties of the composite Al2O3 and MAH on the mechanical properties of PP composites. The composition used was polypropylene: corn husk fiber rasio :Al2O3: MAH, namely 90:5:5:0, 89:5:5:1, 87:5:5:3, and 85:5:5:5% by weight. Tensile strength test using Universal Testing Machine (UTM) and crystallinity test using Differential Scanning Calorimetry (DSC) were conducted to evaluate the material performance. The highest value of tensile strength and crystallinity in the composition with 0 %weight MAH. The results of these tests, showing that the greater the composition of corn husk fiber has an influence on the decrease in tensile strength and crystallinity of the composite.

Comparative analysis of energy performance between clay-based and conventional building materials: A case study in Moroccan semi-arid climate

The environmental challenges arising from using traditional construction materials, such as cement, along with their rapid depletion, underscore the necessity of employing environmentally friendly building materials derived from natural resources. In this context, this study presents a comparative analysis of the energy performance of conventional building materials and clay-based materials. Focusing specifically on the Beni Mellal region, adobe bricks reinforced with straw, at weight percentages of 0%, 2%, and 4%, were manufactured. First, the physicochemical properties of the investigated clay were characterized. Subsequently, the thermophysical properties of the fabricated bricks were determined. Annual simulations were conducted using the TRNSYS software, considering a typical meteorological year (TMY) for Beni Mellal City, located in the semi-arid climatic zone. The energy performance of various passive energy efficiency measures was evaluated and discussed, facilitating a thermal analysis to assess the energy needs for heating and cooling inherent to each building material. The results demonstrate that clay bricks, particularly those reinforced with 4% wheat straw, outperform conventional materials in terms of energy efficiency, highlighting their potential for sustainable construction. This study emphasizes the significance of local clay resources and natural reinforcements in enhancing energy efficiency and provides insights into their application in eco-friendly construction practices, thereby contributing to sustainable development goals

Towards a green & ecological revolution: Review of natural reinforcing bio-composites and bio-hybrid composites

Recently, the use of composite materials has significantly increased in various industries, ranging from automotive to construction, due to their more advantageous properties compared to traditional materials. Nevertheless, with the growing environmental and ecological awareness, researchers are focusing on developing more environmentally friendly and healthier bio-composites while ensuring high-performance, affordable, renewable, biodegradable, and lightweight materials with environmental benefits. This literature review intends to provide an overview of recent work that focuses on bio-composites and bio-hybrid composites with natural reinforcements. Moreover, it presents the natural fillers, their classifications, the cultivation of some plants, their mechanical and chemical characteristics, as well as their potential applications. Additionally, this work describes the modeling, its different approaches, as well as the selection process of a model.