Narrow Beam Divergence Research Articles

High brightness terahertz quantum cascade laser with near-diffraction-limited Gaussian beam

High-power terahertz (THz) quantum cascade laser, as an emerging THz solid-state radiation source, is attracting attention for numerous applications including medicine, sensing, and communication. However, due to the sub-wavelength confinement of the waveguide structure, direct beam brightness upscaling with device area remains elusive due to several mode competition and external optical lens is normally used to enhance the THz beam brightness. Here, we propose a metallic THz photonic crystal resonator with a phase-engineered design for single mode surface emission over a broad area. The quantum cascade surface-emitting laser is capable of delivering an output peak power over 185 mW with a narrow beam divergence of 4.4° × 4.4° at 3.88 THz. A high beam brightness of 1.6 × 107 W sr−1m−2 with near-diffraction-limited M2 factors of 1.4 in both vertical and lateral directions is achieved from a large device area of 1.6 × 1.6 mm2 without using any optical lenses. The adjustable phase shift between the lattices enables a stable and high-intensity surface emission over a broad device area, which makes it an ideal light extractor for large-scale THz emitters. Our research paves the way to high brightness solid-state THz lasers and facilitates new applications in standoff THz imaging, detection, and diagnosis.

High-speed high-power free-space optical communication via directly modulated watt-class photonic-crystal surface-emitting lasers

Photonic crystal surface-emitting lasers (PCSELs), which use a two-dimensional photonic crystal as the laser cavity, can achieve both high output powers and narrow beam divergence angles owing to single-mode lasing over a large area. High-speed, high-power, direct modulation of PCSELs is expected to realize compact and power-saving optical transmitters without bulky lens systems and fiber amplifiers for free-space optical communications. In this paper, we realize high-speed, high-power, free-space optical communication via directly modulated watt-class photonic-crystal surface-emitting lasers. We first numerically investigate the intrinsic (optical) and parasitic (electrical) frequency response characteristics of watt-class PCSELs with large lasing areas, and we show that several-GHz-class direct modulation is feasible even in watt-class PCSELs. Then, we fabricate a 500-µm-diameter PCSEL and simultaneously realize watt-class continuous-wave operation and several-GHz-class direct modulation. Finally, by directly modulating the developed PCSEL with a quadrature amplitude modulation (QAM) signal, we demonstrate free-space optical communication with over 10 Gbit/s high-speed transmission and virtual 5-km-class long-distance transmission even without using a transmitter lens.

Continuous-wave operation of 1550 nm low-threshold triple-lattice photonic-crystal surface-emitting lasers

Benefitting from narrow beam divergence, photonic crystal surface-emitting lasers are expected to play an essential role in the ever-growing fields of optical communication and light detection and ranging. Lasers operating with 1.55 μm wavelengths have attracted particular attention due to their minimum fiber loss and high eye-safe threshold. However, high interband absorption significantly decreases their performance at this 1.55 μm wavelength. Therefore, stronger optical feedback is needed to reduce their threshold and thus improve the output power. Toward this goal, photonic-crystal resonators with deep holes and high dielectric contrast are often used. Nevertheless, the relevant techniques for high-contrast photonic crystals inevitably complicate fabrication and reduce the final yield. In this paper, we demonstrate the first continuous-wave operation of 1.55 μm photonic-crystal surface-emitting lasers by using a ‘triple-lattice photonic-crystal resonator’, which superimposes three lattice point groups to increase the strength of in-plane optical feedback. Using this geometry, the in-plane 180° coupling can be enhanced threefold compared to the normal single-lattice structure. Detailed theoretical and experimental investigations demonstrate the much lower threshold current density of this structure compared to ‘single-lattice’ and ‘double-lattice’ photonic-crystal resonators, verifying our design principles. Our findings provide a new strategy for photonic crystal laser miniaturization, which is crucial for realizing their use in future high-speed applications.

Attitude Determination of Photovoltaic Device by Means of Differential Absorption Imaging

Future wireless power transmission will cover power levels up to kilowatts or more and transmission distances up to the scale of kilometers. With its narrow beam divergence angle, optical wireless power transmission (OWPT) is a promising candidate for such system implementations. In the operation of OWPT, it is necessary to estimate the position, direction (azimuth, elevation), and attitude of the target photovoltaic device before the power supply. The authors have proposed the detection of targets using differential absorption imaging and positioning with a combination of stereo imagery. In the positioning by stereo imagery, a condition regarding the consistency of the left and right images can be defined. This corresponds to the certain value of the exposure time of the image sensor, and this depends on the target’s attitude angle. In this paper, we discuss target attitude estimation using this minimum exposure time at which the integrity measure converges. A physical model was derived under general conditions of target position and experimental configuration. Target attitudes were estimated within an error range of 10 to 15 degrees in approximately 60 degrees range. On the other hand, there is an attitude estimation method based on the apparent size of the target. When using this method to estimate the attitude angle, errors are significantly large for specular and diffuse mixed targets like the PV. The method proposed in this paper is a robust attitude estimation method for the photovoltaic device in OWPT.

Analysis of Tip/Tilt Compensation of Beam Wandering for Space Laser Communication

Laser communication has been considered as a novel method for earth observation satellites with generation of high data volume. It offers faster data transmission speeds compared to conventional radio frequency (RF) communication due to the short wavelength and narrow beam divergence. However, laser beams are refracted due to atmospheric turbulence between the ground and the satellite. Refracted laser beams, upon reaching the receiver, result in angle-of-arrival (AoA) fluctuation, inducing image dancing and wavefront distortion. These phenomena hinder signal acquisition and lead to signal loss in the course of laser communication. So, precise alignment between the transmitter and receiver is essential to guarantee effective and reliable laser communication, which is achieved by pointing, acquisition, and tracking (PAT) system. In this study, we simulate the effectiveness of tip/tilt compensation for more efficient laser communication in the satellite-ground downlink. By compensating for low-order terms using tip/tilt mirror, we verify the alleviation of AoA fluctuations under both weak and strong atmospheric turbulence conditions. And the performance of tip/tilt correction is analyzed in terms of the AoA fluctuation and collected power on the detector.

Proposal and Demonstration of Free-Space Optical Communication Using Photonic Crystal Surface-Emitting Lasers

We propose and demonstrate free-space optical (FSO) communication using photonic crystal surface-emitting lasers (PCSELs). Unlike other types of conventional semiconductor lasers, such as edge-emitting lasers (EELs) and vertical-cavity surface-emitting lasers (VCSELs), PCSELs achieve much larger area single-mode coherent lasing, and this unique feature enables high-power (>watt) and lens-free operations at the same time. To date, these advantages have been recognized to be game changing, especially in light detection and ranging (LiDAR) and laser processing applications. In this work, we show that FSO communication can also benefit from these advantages of PCSELs; more specifically, conventional transmitters that include low-power semiconductor lasers, optical lenses, and fiber-based amplifiers could be replaced with a single PCSEL. Since fiber amplifiers usually consist of bulky components and have low conversion efficiencies, PCSELs can offer more space- and power-saving solutions. Moreover, the narrow beam divergence angles directly obtained from large-area single-mode PCSELs can also eliminate the need for lens systems on the transmitter side. To experimentally verify these potential advantages, we performed FSO transmission experiments based on PCSELs and successfully transmitted 480-MHz and 864-MHz orthogonal frequency division multiplexed (OFDM) signals over 1.1 m using a 500-μm PCSEL in a lens-free transmitter configuration. We believe that PCSELs open new possibilities and choices in FSO communication.

High-brightness scalable continuous-wave single-mode photonic-crystal laser

Realizing large-scale single-mode, high-power, high-beam-quality semiconductor lasers, which rival (or even replace) bulky gas and solid-state lasers, is one of the ultimate goals of photonics and laser physics. Conventional high-power semiconductor lasers, however, inevitably suffer from poor beam quality owing to the onset of many-mode oscillation1,2, and, moreover, the oscillation is destabilized by disruptive thermal effects under continuous-wave (CW) operation3,4. Here, we surmount these challenges by developing large-scale photonic-crystal surface-emitting lasers with controlled Hermitian and non-Hermitian couplings inside the photonic crystal and a pre-installed spatial distribution of the lattice constant, which maintains these couplings even under CW conditions. A CW output power exceeding 50 W with purely single-mode oscillation and an exceptionally narrow beam divergence of 0.05° has been achieved for photonic-crystal surface-emitting lasers with a large resonant diameter of 3 mm, corresponding to over 10,000 wavelengths in the material. The brightness, a figure of merit encapsulating both output power and beam quality, reaches 1 GW cm−2 sr−1, which rivals those of existing bulky lasers. Our work is an important milestone toward the advent of single-mode 1-kW-class semiconductor lasers, which are expected to replace conventional, bulkier lasers in the near future.

Compact and Low Power-Consumption Solid-State Two-Dimensional Beam Scanner Integrating a Passive Optical Phased Array and Hybrid Wavelength-Tunable Laser Diode

Large-scale optical phased arrays have attracted attention as devices for solid-state beam scanning employing light detection and ranging. However, conventional optical phased arrays using electro-optic phase shifters require active phase control for each antenna. Because the power consumption of the active phase shifters is proportional to the number of antennas, the total power consumption increases in a large-scale optical phased array with a narrow beam divergence. In this study, we propose a passive beam scanner that realizes two-dimensional beam scanning through the wavelength sweep of a laser light. Additionally, most studies on optical phased arrays use external laser diodes as light sources. This increases the size of the beam-scanning system. Therefore, there is a demand for integrating an optical phased array and a laser light source in a combined chip. In this study, we integrated a 64-channel passive optical phased array and a hybrid wavelength-tunable laser diode into a combined chip. The size of the device was 5 mm × 1.5 mm, and the power consumption for beam scanning was 49.3 mW. The field of view was 44.2° × 13.7°, and the full width at half maximum of the beam divergence was 0.517° × 3.67°. Compared with the device used in a previous study, our device was nine times smaller, and the total power consumption was only tens of milliwatts. This device consumes less power and achieves a fully integrated light detection and ranging.

1.5 µm wavelength NPN-type photonic-crystal surface-emitting laser exceeding 100 mW.

A 1.5 µm laser diode has applications in eye-safe light detection and ranging (LiDAR) and optical communications via photonic integrated circuits. Photonic-crystal surface-emitting lasers (PCSELs) have lens-free applications in compact optical systems because of narrow beam divergences (<1 degree). However, the output power has still been less than 1 mW for 1.5 µm PCSELs. For higher output power, one approach is suppression of p-dopant Zn diffusion in the photonic crystal layer. Therefore, n-type doping was used for the upper crystal layer. Moreover, an NPN-type PCSEL structure was proposed to reduce intervalence band absorption in the p-InP layer. Here, we demonstrate a 1.5 µm PCSEL with 100 mW output power, which exceeds previous reported values by two orders of magnitude.

Fabrication of high quality X-ray source by gated vertically aligned carbon nanotube field emitters

We fabricated a cold cathode-driven x-ray source with vertically aligned carbon nanotubes (VACNTs). Dose and spatial resolution characteristics are compared to commercially available portable x-ray sources, and our system outperformed its counterparts. At the same 1.0 mAs condition, our x-ray source represented a dose rate of 0.37 mGy/s, which is 7.8 and 2.4 times greater than that of the thermionic emitter and paste carbon nanotubes based commercial x-ray sources, respectively. In addition, our x-ray source represented better image resolution by achieving a nominal focal spot size of 0.35 mm. We believe that high quality x-ray properties were attained, thanks to the narrow electron beam divergence and high reduced brightness of the electrons from VACNTs, and that this will open up advanced x-ray applications.

Low-power consumption InP-based optical phase arrays with non-uniformly spaced output waveguides.

Optical Phase Arrays (OPAs) are expected to be an ideal solution to achieve beam shaping, laser radar (LIDAR), free-space optical communications, and spatially resolved optical sensors, etc. We demonstrated a low-power consumption 32-channel OPA with non-uniformly spaced waveguides based on InP substrate. The phase shifters are based on a p-i-n structure which are operated with reverse bias and have a low power consumption. Besides, in order to improve the performance especially to obtain larger steering angle and narrower beam divergence without increasing the number of channels, we have optimized the spacing between the output waveguides. The fabricated OPA achieved a steering angle of 35° with the side lobe suppression ratio more than 8.2 dB across the angle range from -20° to 20° in the far field, which is the largest phase tuning steering angle reported by InP-based OPAs as far as we know. The divergence angle is about 0.46° in the phase steering dimension and the power consumption of the OPA at each steering angle is lower than 7.5 mW.

Satellite vibration effects on communication quality of OISN system

Abstract Over space optical communications are considered as the critical technology for high-bandwidth, high-speed, and large-capacity communications. Indeed, the laser wavelength’s narrow beam divergence requires a precise beam pointing at both ends of the optical link. The precise beam pointing makes the laser beam pointing to or from a moving object is one of the most challenging processes for optical space communications. In this work, the effect of the pointing error due to satellite platform vibration over the performance of the laser communication link of the optical inter satellite network (OISN) system in terms of the quality factor is investigated. Indeed, an optical communication system has been built using the OptiSystem program to simulate the link between satellites in space for the OISN system. In addition, the proposed system shows by simulation the optimal parameters’ values required for the design of the optical communication link between satellites of the OISN system. Moreover, the effect of pointing error due to the platform vibration on the performance of the OISN system is investigated for different scenarios of the pointing error (i.e., no pointing error; one side of the link with pointing error, and two sides of the link with pointing error). The simulation shows that, first, the optimal parameters that can be used for the optical communication link between satellites of the OISN system in terms of the laser wavelength; laser power; optical modulation scheme; optical telescope aperture diameter; and telescope optical efficiency. In addition, the simulation shows that existing pointing error due to vibration at one side of the optical link leads to degradation of the performance of the OISN system in terms of the quality factor for different laser beam power; distances between satellites; telescope diameters; and telescope efficiencies. Moreover, existing pointing errors at the two sides of the optical link lead to rapid degradation of the considered OISN system performance even with the increase of the laser power or telescope diameter, which tend to compensate for its effect initially and then quit.

A Predefined-Time Control for the Laser Acquisition in Space Gravitational Wave Detection Mission.

The establishment of a laser link between satellites, i.e., the acquisition phase, is a key technology for space-based gravitational detection missions, and it becomes extremely complicated when the long distance between satellites, the inherent limits of the sensor accuracy, the narrow laser beam divergence and the complex space environment are considered. In this paper, we investigate the laser acquisition problem of a new type of satellite equipped with two two-degree-of-freedom telescopes. A predefined-time controller law for the acquisition phase is proposed. Finally, a numerical simulation was conducted to demonstrate the effectiveness of the proposed controller. The results showed that the new strategy has a higher efficiency and the control performance can meet the requirements of the gravitational detection mission.

Circular Optical Phased Array with Large Steering Range and High Resolution.

Light detection and ranging systems based on optical phased arrays and integrated silicon photonics have sparked a surge of applications over the recent years. This includes applications in sensing, free-space communications, or autonomous vehicles, to name a few. Herein, we report a design of two-dimensional optical phased arrays, which are arranged in a grid of concentric rings. We numerically investigate two designs composed of 110 and 820 elements, respectively. Both single-wavelength (1550 nm) and broadband multi-wavelength (1535 nm to 1565 nm) operations are studied. The proposed phased arrays enable free-space beam steering, offering improved performance with narrow beam divergences of only 0.5° and 0.22° for the 110-element and 820-element arrays, respectively, with a main-to-sidelobe suppression ratio higher than 10 dB. The circular array topology also allows large element spacing far beyond the sub-wavelength-scaled limits that are present in one-dimensional linear or two-dimensional rectangular arrays. Under a single-wavelength operation, a solid-angle steering between 0.21π sr and 0.51π sr is obtained for 110- and 820-element arrays, respectively, while the beam steering spans the range of 0.24π sr and 0.57π sr for a multi-wavelength operation. This work opens new opportunities for future optical phased arrays in on-chip photonic applications, in which fast, high-resolution, and broadband beam steering is necessary.

Progress of Photonic-Crystal Surface-Emitting Lasers: A Paradigm Shift in LiDAR Application

Nowadays, the flurry of autonomous vehicles is in full swing regarding light detection and ranging (LiDAR) and depth perception. For such visual perception, light plays an important role. We human beings recognize and distinguish surrounding details when the eye focuses light on the retina. For the LiDAR system, pulsed lasers are employed to measure the relevant range. Thus, appropriate light sources with high performance are in urgent demand. Auspiciously, a revolutionary semiconductor laser technology, namely the photonic-crystal surface-emitting laser (PCSEL), emerges over the past two decades. PCSEL exhibits not only a symmetric beam profile with narrow beam divergence but also a high-power operation with controllability. Therefore, it may be the holy grail for an ultracompact time-of-flight (ToF) LiDAR system. Hereupon, comprehensive analyses of PCSEL-relevant scientific publications and patent documents are conducted. We thereby review the development progress of PCSEL technology. Moreover, a systematic simulation is performed, providing real-time visualization of relevant point clouds with different beam divergence. PCSEL technology with unprecedented merits indeed turns a new leaf and a paradigm shift in LiDAR application is ongoing. It is believed that a lens-free and adjustment-free ultracompact apparatus in simplicity can be expected.

Solid-State Slow-Light Beam Scanner With Ultra-Large Field of View and High Resolution

A light beam scanning technology for 3D sensing has been attracting much interest thanks to its signal-to-noise-ratio merit compared to conventional flash 3D sensing. A Solid-state beam scanner based on a vertical cavity surface emitting laser (VCSEL) with amplification function was invented. In this paper, though enlarging the length of scanner to 6mm, a narrow beam divergence of 4000 was obtained. Its intensity variation is < 40% and could be further improved by better DOE design and fabrication process. The DOE could be simply stacked on the scanner and thus the submodule size of the scanner could be managed within 7mm 1mm 1mm. We also discussed its integrability with a tunable seed laser and its application in 2D beam scanning for better signal to noise ratios.

A large-scale microelectromechanical-systems-based silicon photonics LiDAR

Three-dimensional (3D) imaging sensors allow machines to perceive, map and interact with the surrounding world1. The size of light detection and ranging (LiDAR) devices is often limited by mechanical scanners. Focal plane array-based 3D sensors are promising candidates for solid-state LiDARs because they allow electronic scanning without mechanical moving parts. However, their resolutions have been limited to 512 pixels or smaller2. In this paper, we report on a 16,384-pixel LiDAR with a wide field of view (FoV, 70° × 70°), a fine addressing resolution (0.6° × 0.6°), a narrow beam divergence (0.050° × 0.049°) and a random-access beam addressing with sub-MHz operation speed. The 128 × 128-element focal plane switch array (FPSA) of grating antennas and microelectromechanical systems (MEMS)-actuated optical switches are monolithically integrated on a 10 × 11-mm2 silicon photonic chip, where a 128 × 96 subarray is wire bonded and tested in experiments. 3D imaging with a distance resolution of 1.7 cm is achieved with frequency-modulated continuous-wave (FMCW) ranging in monostatic configuration. The FPSA can be mass-produced in complementary metal–oxide–semiconductor (CMOS) foundries, which will allow ubiquitous 3D sensors for use in autonomous cars, drones, robots and smartphones.

Connectivity Analysis of Mega-Constellation Satellite Networks With Optical Intersatellite Links

Recently, low earth orbit (LEO) satellite-based systems have attracted tremendous attention and various technologies have been developed for payload miniaturization and optical communications. In addition, mega-constellation architectures are expected to be deployed with LEO satellites for global broadband networks. In this article, we present a thorough analysis of mega-constellation architecture in terms of a change in the number of visible satellites and antenna steering capability to investigate the impact of increase in the constellation size and adoption of optical intersatellite links. The network architecture is evaluated with respect to satellite antenna steering capability and the satellite visibility considering the very narrow beam divergence of optical communications. We analyze the impact of a change in relative positions among the satellites due to continuous satellite movement in the constellation. The results offer guidelines for designing a novel visibility matrix using a time-varying satellite topology. This could defuse the problem of the conventional studies using fixed visibility matrices. The proposed time-varying visibility matrix achieves better performance than the previous preassigned links in terms of end-to-end link distance and hop count of LEO satellite networks.

Self-consistent analysis of photonic-crystal surface-emitting lasers under continuous-wave operation.

We develop a self-consistent theoretical model for simulating the lasing characteristics of photonic-crystal surface-emitting lasers (PCSELs) under continuous-wave (CW) operation that takes into account thermal effects caused by current injection. Our model enables us to analyze the lasing characteristics of PCSELs under CW operation by solving self-consistently the changes in the in-plane optical gain and refractive index distribution, which is associated with heat generation and temperature rise, and the change in the oscillation modes. We reveal that the lasing band-edge selectivity and beam quality of the PCSELs are affected by the spatial distribution of the band-edge frequency of the photonic crystal formed by the refractive index distribution, which depends on the temperature distribution in the resonator. Furthermore, we show that single-mode lasing with narrow beam divergence can be realized even at high current injection under CW operation by introducing a photonic-crystal structure with an artificially formed lattice constant distribution, which compensates such band-edge frequency distribution.

Surface grating VCSEL-integrated amplifier/beam scanner with high power and single mode operation

We propose and demonstrate a novel surface-grating vertical cavity surface emitting laser (VCSEL)-integrated amplifier/beam scanner. When the surface of the VCSEL section is periodically etched, a single slow-light mode which travels laterally into the amplifier section is selected due to the wavelength selectivity of the grating. The coupled slow light can be amplified with pumping the amplifier above the threshold. The far field angle of the amplified slow light can be continuously tuned through changing the pumping current at the VCSEL. We fabricated the integrated device with a 400 μm long VCSEL section and 1 mm long amplifier section, realizing in a single mode coupling power of over 7 mW and high output power of over 500 mW under pulsed operations of the amplifier. The continuous fan beam steering of 1.5° and a diffraction-limited narrow beam divergence of 0.06° are also achieved. We also fabricated device with extending the amplifier section length to 2 mm. A high single mode power of 1 W under pulsed operations is achieved, which is the record high power operation for single-mode VCSELs. With the performance of both high power and good beam quality, our new device shows great potential to be used as light source for LiDAR and other sensing applications.