NaCl Aerosol Research Articles

Effect of surface orientation on the corrosion behavior of Ni-based single-crystal alloy in a simulated marine atmosphere at 750 °C

DD5 single-crystal alloy samples with different surface orientations were obtained by machining the alloy ingot perpendicular (PP) and parallel (P), respectively, to its solidification direction (SD). The corrosion behaviors of the PPSD and PSD alloy samples were investigated in the atmosphere of moist air + NaCl aerosol at 750 °C. Results showed that during initial corrosion, γ′ phase developed a thin NiO layer with Al internal corrosion product. However, a NiO nodule with an internal Cr2O3 layer was formed on γ phase. As corrosion progressed, the corrosion product gradually grew to a NiO/(Al, Cr)2O3 bilayer, accompanied by internal corrosion consisting of Al2O3. It was also found that the PSD sample with a lower fraction and smaller size of γ’ phases exhibited better corrosion resistance than the PPSD sample. The effect of alloy surface orientation on the corrosion mechanism was discussed.

NaCl aerosol filtration over filter media with intrafiber porosity: can filtrate capacity be increased by wicking into this pore volume?

This paper investigates a novel fiber-based filter media wherein a NaCl filtrate is collected and reservoired not only onto the surfaces of the fibers and within their inter-fiber voidage but also within the internal porosity of high pore volume nanoporous fibers or vapor grown carbon nanofibers (VGCF) floc used to fabricate the media. This transport process is shown to occur through a NaCl dissolution into the water-filled nanopores of the fiber and a subsequent intra-fiber wicking phenomenon. The study further elucidates two distinct NaCl accommodation mechanisms which are uniquely available to filter media containing nanoporous intrafiber porosity: (1) wicking and capillary condensation of liquid NaCl aerosols directly into the intrafiber pores at high RH, and (2) dissolution of otherwise solid NaCl aerosols deposited onto fiber surfaces (at low RH) into the interior nanopores of the fiber because these pores (when hydrophilic) are saturated with water (even at low RH). To investigate these two mechanistic regimes, various media were fabricated possessing multiscale porosity in the form of: (i) embedded flocs of VGCFs (4.108 cm3gm-1pore volume), (ii) hydrophilic and high pore volume activated carbon fibers (ACFs, 0.950 cm3gm-1) and (iii) solid graphite fibers. These media were then comparatively evaluated toward NaCl aerosol filtration at different relative humidities. Pressure drop measurements versus filtrate accumulation and SEM-EDAX VGCF demonstrated the location and transport of NaCl into the intrafiber voidage. Media containing both VGCF floc and ACF accumulated 1200% more NaCl at low RH (and a specified pressure drop) than similar media prepared from non-porous graphite fibers, with an additional 315% increase from low to high RH. A Gibbs free energy driving force model is provided to illustrate the driving forces favoring water condensation into the nanopores and solid NaCl aerosol dissolution into the water phase. Filtration efficiency and quality factor assessments for the various media are also systematically evaluated to demonstrate the observed mechanistics.

Imaging Dissolution Dynamics of Individual NaCl Nanoparticles during Deliquescence with In Situ Transmission Electron Microscopy.

Water vapor condensation on hygroscopic aerosol particles plays an important role in cloud formation, climate change, secondary aerosol formation, and aerosol aging. Conventional understanding considers deliquescence of nanosized hygroscopic aerosol particles a nearly instantaneous solid to liquid phase transition. However, the nanoscale dynamics of water condensation and aerosol particle dissolution prior to and during deliquescence remain obscure due to a lack of high spatial and temporal resolution single particle measurements. Here we use real time in situ transmission electron microscopy (TEM) imaging of individual sodium chloride (NaCl) nanoparticles to demonstrate that water adsorption and aerosol particle dissolution prior to and during deliquescence is a multistep dynamic process. Water condensation and aerosol particle dissolution was investigated for lab generated NaCl aerosols and found to occur in three distinct stages as a function of increasing relative humidity (RH). First, a < 100 nm water layer adsorbed on the NaCl cubes and caused sharp corners to dissolve and truncate. The water layer grew to several hundred nanometers with increasing RH and was rapidly saturated with solute, as evidenced by halting of particle dissolution. Adjacent cube corners displayed second-scale curvature fluctuations with no net particle dissolution or water layer thickness change. We propose that droplet solute concentration fluctuations drove NaCl transport from regions of high local curvature to regions of low curvature. Finally, we observed coexistence of a liquid water droplet and aerosol particle immediately prior to deliquescence. Particles dissolved discretely along single crystallographic directions, separated by few second lag times with no dissolution. This work demonstrates that deliquescence of simple pure salt particles with sizes in the range of 100 nm to several microns is not an instantaneous phase transition and instead involves a range of complex dissolution and water condensation dynamics.

Measurement of inward leakage of full-face masks in EN and ISO standards: comparison of gas and aerosol test agents.

In Europe, respiratory protective devices must be certified before they can be marketed. Among the parameters of interest, inward leakage (IL) characterizes the tightness between the face seal and the face, to verify that the device is well-designed. European standard EN 13274-1 (2001) and International Organization for Standardization (ISO) standard ISO 16900-1 (2019) specify that IL should be measured using sodium chloride (NaCl) aerosol or sulfur hexafluoride (SF6) gas. For reusable masks made of nonporous materials, both test agents are considered equally acceptable. However, the few studies that have compared IL values measured with various aerosols and gases have come to divergent conclusions. This work then aimed to measure IL with the test agents recommended by the standards to determine whether they are really equivalent. Since krypton (Kr) is an interesting candidate for replacing SF6 in standard tests, IL was assessed with SF6 and Kr simultaneously, and with NaCl aerosol using various calculation methods. Tests were carried out on 5 models of full-face masks donned on a headform connected to a breathing machine simulating 3 sinusoidal breathing rates of various intensities. The respirator fit on the headform was evaluated using a controlled negative pressure method to determine a manikin fit factor. Four scenarios were then tested to represent very poor, bad, good, and excellent fit. Gas concentration was measured using a mass spectrometer, and IL was calculated for SF6 and Kr. A combination of 3 devices allowed the determination of the number-based concentration of particles with diameters between 20 nm and 2 µm, and IL was calculated for each of the 33 channels, as well as using a cumulative number concentration. In addition, to comply with standards, a conversion was carried out to calculate IL using a cumulative mass concentration. The results of this work evidenced that the IL values measured with NaCl were systematically lower than those determined with gases. IL was also shown to vary with particle size, with a maximum value exceeding that calculated with cumulative concentrations (in number or mass). As part of the revision of the standards, protocols for measuring inward leakage should be redefined. On the one hand, acceptability thresholds should be re-evaluated according to the nature of the test agent (gas or aerosol), as it is clear that the 2 options do not give the same results for a given configuration. On the other hand, the aerosol leakage measurement protocol needs to be reworked to enable the measurement of a well-defined, robust, and reproducible inward leakage value.

Evaluating layer contributions and salt coating effects on mask performance.

The impact of respiratory diseases is vast and multifaceted, affecting individuals, healthcare systems, and global economies. In response to the spread of respiratory pathogens, masks and respirators have become pivotal, demonstrating their capability to mitigate transmission. However, the limitations of conventional face masks or respirators, such as their single-use nature, environmental impact, and the risk of contact-based transmission, have accelerated the development of antimicrobial masks. Designing effective antimicrobial masks requires a deep understanding of the properties of each layer and the identification of an optimal configuration to enhance their protective efficiency. In this study, we investigated the filtration performance, including filtration efficiency and breathability, of individual layers in conventional 3-ply masks and stacked spunbond (SB) fabrics with and without salt coating, under both dry and wet fabric conditions. We aimed to elucidate the filtration efficiency of each mask layer with respect to particle size and type (NaCl aerosols, DOP aerosols), with particular focus on the impact of salt-coated SB fabric and its application. While bare fabrics showed a decrease in filtration efficiency with increased wetness, salt-coated fabrics exhibited enhanced filtration efficiency. Importantly, evaluating the efficacy of a stack comprised of salt-coated SB fabrics across diverse antimicrobial respiratory devices highlighted its efficacy as both the outermost layer in a 3-ply mask and as a mask covering (i.e., a supplementary layer over a mask or respirator). This investigation not only emphasizes the significance of salt-coated antimicrobial technology in mitigating disease transmission but also offers a practical approach for adeptly implementing this technology in respiratory protection devices.

Quaternary ammonium salt coated air filter for bioaerosol removal from building indoor air

Developing air filters with biocidal ability is important to protect the public from infectious respiratory diseases. A simple spray-coating approach was devised to fabricate antimicrobial air filters to remove bioaerosols. The commercial antimicrobial agent Goldshield 75 was coated on the air filters through covalent immobilization, endowing the fabricated filter with long-lasting biocidal ability. All coated filters significantly inhibited both Gram-positive bacteria (Micrococcus luteus) and Gram-negative bacteria (Escherichia coli). The antibacterial ability of the coated filters is similar to the commercial AeraSafe antibacterial filter. The coated filter showed over 99.9 % antibacterial efficiency 3 months after the application of the coating. Both bacterial and virus filtration efficiencies of coated charged polypropylene filter were higher than 99.9 %. The coating did not have much effect on the NaCl aerosol filtration efficiency of the filters. This simple spray-coating strategy is a practical method for producing antimicrobial air filters for the prevention of infectious respiratory diseases.

Fabrication of breathable superhydrophobic composite fabric with moisture permeability and weak-electric-field bactericidal ability designed for protective clothing applications

Most protective clothing on the market today cannot provide both comfort properties and protectability, which would not match the requirement for preventing or killing the rapidly growing and changing virus. Hence, a novel breathable and waterproof composite fabric used in protective clothing was designed through the hot-press process with three functional layers. The waterproof ability, moisture permeability, mechanical property, electricity and bactericidal ability of three layers and composite fabric were studied. Results showed that the moisture permeability of coated thermoplastic polyurethane (TPU) membrane reached 19854 g m2 d−1. The composite fabric had still excellent moisture permeability of up to 13956 g m2 d−1 and water contact angle of 151.7°. The coated TPU membrane had good tensile strength and acid resistance. The voltage and current of composite fabric after 7 days were approximately 0.336 V and 1.4 μA. The composite fabric had a 97.5 % filtering effect for NaCl aerosols, a 99 % bacteriostatic rate, and the ability to withstand the Phy-X174 phage with a diameter of 0.027 μm. This composite fabric based on the principle of moisture permeability and weak electric field could be used in protective clothing, which would be of theoretical significance and guiding practical production.

Sub-ppb NaCl aerosol detection at a distance of 30 meters by femtosecond laser induced plasma spectroscopy.

In this work, sub-ppb aerosol detection is achieved by femtosecond laser filament with a single pulse energy of 4 mJ at a distance of 30 m. A concave mirror with an open aperture of 41.4 cm is employed in an off-axis optical system to focus the femtosecond laser beam and collect the fluorescence of NaCl aerosol. The simulation and experimental results show that the astigmatism can be greatly reduced when femtosecond laser beam is incident non-symmetrically on the concave mirror. Compared with the case that femtosecond laser strikes at the center of the concave mirror, the intensity of acoustic signal emitted from the optical filament is increased by 69.5 times, and the detection of limit of sodium element in aerosol is reduced by 86%, which is down to 0.32 ppb. The improved excitation scheme in this work utilizes the nonsymmetrical beam spot on the concave mirror to compensate the non-symmetry induced by the off-axis setup, reducing the astigmatism of the focusing laser beam and decreasing the sodium chloride aerosol's detection of limit.

Design of PTFE/PP multilayer composite membrane as mask filter layer with steady filtration efficiency and high dust holding capacity

Currently, commercially available mask filter materials, such as electrostatic electret polypropylene (PP) melt-blown cloth and polytetrafluoroethylene (PTFE) nanofiber membranes, always suffer a compromise between filtration efficiency and dust holding capacity, when used alone during air purification. In this study, a novel multilayer composite membrane was designed by thermally laminating a PP melt-blown filter layer (as the dust-holding layer) and a PTFE (Polytetrafluoroethylene) nanofiber layer (as the filtration layer), to improve filtration stability and capacity. The performance of the composite membrane was examined in relation to the effect of key laminating parameters (i.e., temperature, pressure and speed) on the dust holding capacity, filtration efficiency and resistance. NaCl aerosol was used as the model dust source. Results show that the composite membrane, prepared at a lamination temperature of 120 °C, a lamination pressure of 0.2 MPa and a lamination speed of 4 m/min, had a dust-holding capacity of 12.21 g/m2, which was over six times higher than that of the PTFE nanofiber membrane alone. During ten repeated cycles of NaCl aerosol filtration, water washing and alcohol disinfection, the composite membrane exhibited a steady filtration efficiency of above 99.9% over the NaCl aerosol. Meanwhile, the dust holding capacity was maintained above 8 g/m2 over the multiple cycles, while the resistance was smaller than 70 Pa.

Suitability of Low-Cost Sensors for Submicron Aerosol Particle Measurement

The measurement and assessment of indoor air quality in terms of respirable particulate constituents is relevant, especially in light of the COVID-19 pandemic and associated infection events. To analyze indoor infectious potential and to develop customized hygiene concepts, the measurement monitoring of the anthropogenic aerosol spreading is necessary. For indoor aerosol measurements usually standard lab equipment is used. However, these devices are time-consuming, expensive and unwieldy. The idea is to replace this standard laboratory equipment with low-cost sensors widely used for monitoring fine dust (particulate matter—PM). Due to the low acquisition costs, many sensors can be used to determine the aerosol load, even in large rooms. Thus, the aim of this work is to verify the measurement capability of low-cost sensors. For this purpose, two different models of low-cost sensors are compared with established laboratory measuring instruments. The study was performed with artificially prepared NaCl aerosols with a well-defined size and morphology. In addition, the influence of the relative humidity, which can vary significantly indoors, on the measurement capability of the low-cost sensors is investigated. For this purpose, a heating stage was developed and tested. The results show a discrepancy in measurement capability between low-cost sensors and laboratory measuring instruments. This difference can be attributed to the partially different measuring method, as well as the different measuring particle size ranges. The determined measurement accuracy is nevertheless good, considering the compactness and the acquisition price of the low-cost sensors.

Heterogeneous and Photosensitized Oxidative Degradation Kinetics of the Plastic Additive Bisphenol-A in Sea Spray Aerosol Mimics.

Plastics have become ubiquitous in the world's oceans, and recent work indicates that they can transfer from the ocean to the atmosphere in sea spray aerosol (SSA). Hazardous chemical residues in plastics, including bisphenol-A (BPA), represent a sizable fraction of consumer plastics and have been measured consistently in air over both terrestrial and marine environments. However, the chemical lifetimes of BPA and mechanisms by which plastic residues degrade with respect to photochemical and heterogeneous oxidation processes in aerosols are unknown. Here, we present the photosensitized and OH-initiated heterogeneous oxidation kinetics of BPA in the aerosol phase consisting of pure-component BPA and internal mixtures of BPA, NaCl, and dissolved photosensitizing organic matter. We found that photosensitizers enhanced BPA degradation in binary-component BPA + photosensitizer aerosol mixtures when irradiated in the absence of OH. OH-initiated degradation of BPA was enhanced in the presence of NaCl with and without photosensitizing species. We attribute this enhanced degradation to greater mobility and thus reaction probability between BPA, OH, and reactive chlorine species (RCS) formed through reaction between OH and dissolved Cl- in the more liquid-like aerosol matrix in the presence of NaCl. Addition of the photosensitizers in the ternary-component BPA + NaCl + photosensitizer aerosol led to no enhancement in the degradation of BPA following light exposure compared to the binary-component BPA + NaCl aerosol. This was attributed to quenching of triplet state formation by dissolved Cl- in the less viscous aqueous aerosol mixtures containing NaCl. Based upon measured second-order heterogeneous reaction rates, the estimated lifetime of BPA with respect to heterogeneous oxidation by OH is one week in the presence of NaCl compared to 20 days in the absence of NaCl. This work highlights the important heterogeneous and photosensitized reactions and the role of phase state, which affect the lifetimes of hazardous plastic pollutants in SSA with implications for understanding pollutant transport and exposure risks in coastal marine environments.

2 Low-Cost Pm Sensor Performance Testing

Abstract Low-cost particulate matters sensors (LCPMS) are widely used in indoor and outdoor air quality monitoring. Previous studies have explored the accuracy and precision of sensors, showing that LCPMS were most accurate for PM with diameters below 1 μm, and they poorly measured PM in the 2.5–5 μm range. The study aimed to investigate the aspiration and transmission efficiency of LCPMS, to set up a standard aerosol mass concentration generation system, to further comprehend the performance characteristics of LCPMS, and to examine the effect of aerosol loading. Three models of Plantower sensors were tested in this work. An ultrasonic atomizing nozzle was used to generate micrometer-sized NaCl aerosol particles. A TSI aerodynamic particle sizer was used to measure the aerosol concentrations and size distributions upstream and downstream of the LCPMS, to determine the aspiration and transmission efficiency. The mass concentration, from 20 µg/m3 to 200 mg/m3, could be varied by controlling the solution feeding rate and the solution concentration. The high mass concentration was mainly designed for aerosol loading study. The results showed that the aspiration efficiencies of the tested LCPMS were all almost 100% for particle smaller than 5 µm. The transmission efficiency of these sensors was function of particle size and strongly dependent on sampling flow. All sensors tested showed significant performance degrading when challenged with high mass concentration. The orientation of the sensor also played a role affecting the aerosol loading. These sensors performed better when mass concentration is below 100 µg/m3.

Aerosol charge neutralization and its impact on particle filtration efficiency of common face mask materials

Despite the significant increase in research on mask filtration testing since the COVID-19 pandemic, there remains considerable ambiguity regarding which parameters affect particle filtration efficiency (PFE) and how differences in standard testing protocols can lead to divergent PFE values. We evaluated the PFE (and differential pressure) of several common face masks and community face mask materials including woven cotton, spunbond polypropylene, and meltblown polypropylene, testing in accordance with ASTM F2100/2299 standards for medical masks, using polystyrene latex (PSL) aerosol, as well as NIOSH standards for respirators, using NaCl aerosol. In both cases, PFE was measured with and without aerosol charge neutralization, which is used to bring the particle population to a known, equilibrium bipolar charge distribution. Aerosols of either composition that were untreated (not neutralized) led to significant increases in measured PFE, especially in the case of PSL. In contrast, effective neutralization led to lower PFE measurements that also showed little to no dependence on aerosol composition across most materials. To investigate further, the bipolar charge distributions of PSL and NaCl aerosols, both neutralized and untreated, were characterized using an aerodynamic aerosol classifier operated in tandem with a scanning mobility particle sizer (AAC-SMPS). This technique illustrated the differences in the distribution of particle charge states between PSL and NaCl aerosols of the same size, and between PSL particles of different sizes, revealing the presence of highly charged particles in many cases. Most importantly, the equilibrium charge distribution after neutralization is shown to be independent of particle composition or initial charge distribution, highlighting the crucial role of aerosol charge neutralizers in preventing overestimates of mask performance (due to electrostatic effects) and promoting consistency in standard testing procedures.

Fabrication of Laminated Micro/Nano Filter and Its Application for Inhalable PM Removal

Particulate matter (PM) with a diameter of 0.3 µm is inhalable and brings great threats to human health. Traditional meltblown nonwovens used for air filtration need to be treated by high voltage corona charging, which has the problem of electrostatic dissipation and thus reduces the filtration efficiency. In this work, a kind of composite air-filter with high efficiency and low resistance was fabricated by alternating lamination of ultrathin electronspun nano-layer and melt-blown layer without corona charging treatment. The effects of fiber diameter, pore size, porosity, layer number, and weight on filtration performance were investigated. Meanwhile, the surface hydrophobicity, loading capacity, and storage stability of the composite filter were studied. The results indicate that the filters (18.5 gsm) laminated by 10 layers fiber-webs present excellent filtration efficiency (97.94%), low pressure drop (53.2 Pa), high quality factor (QF 0.073 Pa-1), and high dust holding capacity (9.72 g/m2) for NaCl aerosol particles. Increasing the layers and reducing individual layer weight can significantly improve filtration efficiency and reduce pressure drop of the filter. The filtration efficiency decayed slightly from 97.94% to 96.48% after 80 days storage. The alternate arrangement of ultra-thin nano and melt-blown layers constructed a layer-by-layer interception and collaborative filtering effect in the composite filter, realizing the high filtration efficiency and low resistance without high voltage corona charging. These results provided new insights for the application of nonwoven fabrics in air filtration.

Assessment of aerosol persistence in ICUs via low-cost sensor network and zonal models

The COVID-19 pandemic raised public awareness about airborne particulate matter (PM) due to the spread of infectious diseases via the respiratory route. The persistence of potentially infectious aerosols in public spaces and the spread of nosocomial infections in medical settings deserve careful investigation; however, a systematic approach characterizing the fate of aerosols in clinical environments has not been reported. This paper presents a methodology for mapping aerosol propagation using a low-cost PM sensor network in ICU and adjacent environments and the subsequent development of the data-driven zonal model. Mimicking aerosol generation by a patient, we generated trace NaCl aerosols and monitored their propagation in the environment. In positive (closed door) and neutral-pressure (open door) ICUs, up to 6% or 19%, respectively, of all PM escaped through the door gaps; however, the outside sensors did not register an aerosol spike in negative-pressure ICUs. The K-means clustering analysis of temporospatial aerosol concentration data suggests that ICU can be represented by three distinct zones: (1) near the aerosol source, (2) room periphery, and (3) outside the room. The data suggests two-phase plume behavior: dispersion of the original aerosol spike throughout the room, followed by an evacuation phase where "well-mixed" aerosol concentration decayed uniformly. Decay rates were calculated for positive, neutral, and negative pressure operations, with negative-pressure rooms clearing out nearly twice as fast. These decay trends closely followed the air exchange rates. This research demonstrates the methodology for aerosol monitoring in medical settings. This study is limited by a relatively small data set and is specific to single-occupancy ICU rooms. Future work needs to evaluate medical settings with high risks of infectious disease transmission.

Topography and electrostatic interactions of electret fibres in N95 facemasks

Facemasks have been a critical line of defense in the Covid-19 pandemic and have been used for decades to reduce the inhalation of sub-micron aerosols, including bacteria, viruses and nano-materials. These facemasks leverage electrostatic charge properties of non-woven electret fibre mats to remove sub-micron aerosols. However, the topographical and electrostatic properties of these mats have not been well characterized at the nano-scale. In this study, we use atomic force microscopy (AFM) to examine the surface topography of the electret fibres within a commercial respirator fibre mat, use electrostatic force microscopy to map the electrostatic interactions emanating from these fibres, and use synchrotron X-ray scattering to probe polymer morphology. We find that within these mats the fibres exhibit significant heterogeneity in surface topography, electrostatic interactions and polypropylene phase composition. The surface topographies ranged from nano-smooth surfaces to ordered spherulitic structures. The electrostatic interactions varied across fibre length and circumference, and are only weakly correlated with surface topographical features. Finally, we use AFM to characterize fibres after filtering a NaCl aerosol and find that the deposited particles are heterogeneous in size and distributed over the fibre surfaces.

High directional aerosol fluorescence distribution affected by Mie scattering during femtosecond laser filamentation in air

Backward angular distributions of the sodium fluorescence in NaCl aerosols induced by femtosecond laser filamentation in air with a distance of 10 m are measured. The recorded signals appear as strong angular dependence. Further study indicates that it could be associated with the Mie scattering of the filamentation-induced “aerosol lasing” in the forward direction. These results will benefit the remote-sensing of air pollutants by femtosecond laser filamentation-based LIDAR (light detection and ranging).

Biobased Antiviral Nonwoven Mask Filter with High Filtration Performance

The COVID-19 pandemic has resulted in an increased demand of functional nonwovens for face mask applications. In this study, biobased nonwoven filters (NWFs) loaded with silver nanoparticles (AgNPs) were developed. The AgNPs were prepared by reducing Ag+ with lignin extracted from Miscanthus × giganteus. The effects of AgNO3 concentration, reaction time, and temperature on AgNP synthesis were studied using UV–vis spectroscopy. The AgNPs were incorporated into ethyl cellulose fibers through electrospinning. The resulting composite fibers were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, and X-ray diffraction. The average diameter of AgNPs was 6.54 ± 2.3 nm, while the bead-free electrosopun fibers had diameters ranging from 153 to 184 nm. The filtration efficiency, pressure drop, and quality factor of the NWFs were tested against NaCl aerosol particles (≥0.3 μm). The NWF samples tested had filtration efficiency of higher than 99%, with pressure drop and quality factor values of 86.20–88.25 Pa and 0.0690–0.0772 Pa–1, respectively. The antiviral properties of the AgNP-loaded NWFs were evaluated against a surrogate virus, Pseudomonas bacteriophage Φ6, resulting in a 5 log10 (PFU/mL) reduction beyond the starting viral titer. This study demonstrated the potential of the antiviral NWFs for high-performance mask filter applications.

Experimental Study of Spectral Processing Technology for Improving Detection Ability of Low-Concentration NaCl Aerosol by Filament-Induced Fluorescence Spectrum

Experimental Study of Spectral Processing Technology for Improving Detection Ability of Low-Concentration NaCl Aerosol by Filament-Induced Fluorescence Spectrum

Spectra Detection of NaCl Aerosol Fluorescence Induced by Femtosecond Laser Filament Based on Fresnel Lens and Fabry-Perot Interferometer

Spectra Detection of NaCl Aerosol Fluorescence Induced by Femtosecond Laser Filament Based on Fresnel Lens and Fabry-Perot Interferometer