Multi-pinhole Design Research Articles

Development of a backlit-multi-pinhole radiography source.

Backlit-pinhole radiography uses a pinhole placed between an x-ray source and a sample. The backlit-multi-pinhole design uses two pinholes on the same substrate, which are separated by a wall, to create two radiographic images projected along similar axes. The wall, a 100-μm thick titanium foil, prevents x-rays generated near one pinhole from exiting the other pinhole. First results indicate that the multi-pinhole target can create two independent radiographs along similar axes. The images are recorded 2 ns apart. Details of our multi-pinhole design and our first results are discussed.

System geometry optimization for molecular breast tomosynthesis with focusing multi-pinhole collimators

Imaging of 99mTc-labelled tracers is gaining popularity for detecting breast tumours. Recently, we proposed a novel design for molecular breast tomosynthesis (MBT) based on two sliding focusing multi-pinhole collimators that scan a modestly compressed breast. Simulation studies indicate that MBT has the potential to improve the tumour-to-background contrast-to-noise ratio significantly over state-of-the-art planar molecular breast imaging. The aim of the present paper is to optimize the collimator-detector geometry of MBT. Using analytical models, we first optimized sensitivity at different fixed system resolutions (ranging from 5 to 12 mm) by tuning the pinhole diameters and the distance between breast and detector for a whole series of automatically generated multi-pinhole designs. We evaluated both MBT with a conventional continuous crystal detector with 3.2 mm intrinsic resolution and with a pixelated detector with 1.6 mm pixels. Subsequently, full system simulations of a breast phantom containing several lesions were performed for the optimized geometry at each system resolution for both types of detector. From these simulations, we found that tumour-to-background contrast-to-noise ratio was highest for systems in the 7 mm–10 mm system resolution range over which it hardly varied. No significant differences between the two detector types were found.

Off-Axis Imaging in Keel-Edge Pinhole Single Photon Emission Computed Tomography System Based on Monte Carlo Simulation

Monte Carlo simulation is applied to investigate the off-axis effect in keel-edge pinhole single photon emission computed tomography imaging. Aiming at finding the effective field of view (FOV) for imaging, we simulate point source in off-axis imaging (0, 4, 8 and 12 mm from the central rotation axis) of different collimator designs (channel height with 1.38, 1 and 0.5 mm) with a fixed aperture diameter. Tradeoff curves of rms resolution and sensitivity are plotted to determine the effective FOV for different channel height pinhole collimators. The parameterized model can be further incorporated into image reconstruction algorithms, which compensates for the off-axis effect and is used as a reference for multi-pinhole design.

An extension to artifact-free projection overlaps.

In multipinhole single photon emission computed tomography, the overlapping of projections has been used to increase sensitivity. Avoiding artifacts in the reconstructed image associated with projection overlaps (multiplexing) is a critical issue. In our previous report, two types of artifact-free projection overlaps, i.e., projection overlaps that do not lead to artifacts in the reconstructed image, were formally defined and proved, and were validated via simulations. In this work, a new proposition is introduced to extend the previously defined type-II artifact-free projection overlaps so that a broader range of artifact-free overlaps is accommodated. One practical purpose of the new extension is to design a baffle window multipinhole system with artifact-free projection overlaps. First, the extended type-II artifact-free overlap was theoretically defined and proved. The new proposition accommodates the situation where the extended type-II artifact-free projection overlaps can be produced with incorrectly reconstructed portions in the reconstructed image. Next, to validate the theory, the extended-type-II artifact-free overlaps were employed in designing the multiplexing multipinhole spiral orbit imaging systems with a baffle window. Numerical validations were performed via simulations, where the corresponding 1-pinhole nonmultiplexing reconstruction results were used as the benchmark for artifact-free reconstructions. The mean square error (MSE) was the metric used for comparisons of noise-free reconstructed images. Noisy reconstructions were also performed as part of the validations. Simulation results show that for noise-free reconstructions, the MSEs of the reconstructed images of the artifact-free multiplexing systems are very similar to those of the corresponding 1-pinhole systems. No artifacts were observed in the reconstructed images. Therefore, the testing results for artifact-free multiplexing systems designed using the extended type-II artifact-free overlaps numerically validated the developed theory. First, the extension itself is of theoretical importance because it broadens the selection range for optimizing multiplexing multipinhole designs. Second, the extension has an immediate application: using a baffle window to design a special spiral orbit multipinhole imaging system with projection overlaps in the orbit axial direction. Such an artifact-free baffle window design makes it possible for us to image any axial portion of interest of a long object with projection overlaps to increase sensitivity.

Optimized Multipinhole Design for Mouse Imaging

The aim of this study was to enhance high-sensitivity imaging of a limited field of view in mice using multipinhole collimators on a dual head clinical gamma camera. A fast analytical method was used to predict the contrast-to-noise ratio (CNR) in many points of a homogeneous cylinder for a large number of pinhole collimator designs with modest overlap. The design providing the best overall CNR, a configuration with 7 pinholes, was selected. Next, the pinhole pattern was made slightly irregular to reduce multiplexing artifacts. Two identical, but mirrored 7-pinhole plates were manufactured. In addition, the calibration procedure was refined to cope with small deviations of the camera from circular motion. First, the new plates were tested by reconstructing a simulated homogeneous cylinder measurement. Second, a Jaszczak phantom filled with 37 MBq 99mTc was imaged on a dual head gamma camera, equipped with the new pinhole collimators. The image quality before and after refined calibration was compared for both heads, reconstructed separately and together. Next, 20 short scans of the same phantom were performed with single and multipinhole collimation to investigate the noise improvement of the new design. Finally, two normal mice were scanned using the new multipinhole designs to illustrate the reachable image quality of abdomen and thyroid imaging. The simulation study indicated that the irregular patterns suppress most multiplexing artifacts. Using body support information strongly reduces the remaining multiplexing artifacts. Refined calibration improved the spatial resolution. Depending on the location in the phantom, the CNR increased with a factor of 1 to 2.5 using the new instead of a single pinhole design. The first proof of principle scans and reconstructions were successful, allowing the release of the new plates and software for preclinical studies in mice.

Single and Multipinhole Collimator Design Evaluation Method for Small Animal SPECT

High-resolution functional imaging of small animals is often obtained by single pinhole SPECT with circular orbit acquisition. Multipinhole SPECT adds information due to its improved sampling, and can improve the trade-off between resolution and sensitivity. To evaluate different pinhole collimator designs an efficient method is needed that quantifies the reconstruction image quality. In this paper, we propose a fast, approximate method that examines the quality of individual voxels of a postsmoothed maximum likelihood expectation maximization (MLEM) reconstruction by studying their linearized local impulse response (LLIR) and (co)variance for a predefined target resolution. For validation, the contrast-to-noise ratios (CNRs) in some voxels of a homogeneous sphere and of a realistic rat brain software phantom were calculated for many single and multipinhole designs. A good agreement was observed between the CNRs obtained with the approximate method and those obtained with postsmoothed MLEM reconstructions of simulated noisy projections. This good agreement was quantified by a least squares fit through these results, which yielded a line with slope 1.02 (1.00 expected) and a y-intercept close to zero (0 expected). 95.4% of the validation points lie within three standard deviations from that line. Using the approximate method, the influence on the CNR of varying a parameter in realistic single and multipinhole designs was examined. The investigated parameters were the aperture diameter, the distance between the apertures and the axis-of-rotation, the focal distance, the acceptance angle, the position of the apertures, the focusing distance, and the number of pinholes. The results can generally be explained by the change in sensitivity, the amount of postsmoothing, and the amount of overlap in the projections. The method was applied to multipinhole designs with apertures focusing at a single point, but is also applicable to other designs.

Optimal number of pinholes in multi-pinhole SPECT for mouse brain imaging—a simulation study

This study simulates a multi-pinhole single-photon emission computed tomography (SPECT) system using the Monte Carlo method, and investigates different multi-pinhole designs for quantitative mouse brain imaging. Prior approaches investigating multi-pinhole SPECT were not often optimal, as the number and geometrical arrangement of pinholes were usually chosen empirically. The present study seeks to optimize the number of pinholes for a given pinhole arrangement, and also for the specific application of quantitative neuroreceptor binding in the mouse brain. An analytical Monte Carlo simulation based method was used to generate the projection data for various count levels. A three-dimensional ordered-subsets expectation-maximization algorithm was developed and used to reconstruct the images, incorporating a realistic pinhole model for resolution recovery and noise reduction. Although artefacts arising from overlapping projections could be a major problem in multi-pinhole reconstruction, the cold-rod phantom study showed minimal loss of spatial resolution in multi-pinhole systems, compared to a single-pinhole system with the same pinhole diameter. A quantitative study of neuroreceptor binding sites using a mouse brain phantom and low activity (37 MBq) showed that the multi-pinhole system outperformed the single-pinhole system by maintaining the mean and lowering the variance in the measured uptake ratio. Multi-pinhole collimation can be used to reduce the injected dose and thereby reduce the radiation exposure to the animal. Results also suggest that the nine-pinhole configuration shown in this paper is a good choice for mouse brain imaging.