Multimode Interference Splitter Research Articles

Near-infrared Y-branch polymer splitters realized with compact MMI structures for efficient power splitting

Optical splitters are promising photonic devices for next-generation photonic integrated circuits, which enable signal distribution and routing between the different components, facilitating complex optical functionalities on a single chip. This research introduces what we believe is a novel numerical technique for enhancing optical network efficiency by incorporating a taper-based step-index (SI) Y-branch multimode interference (MMI) splitter with organic-inorganic hybrid polymer materials. The proposed device comprises a core width of 5 µm for the input and output waveguides to satisfy the single-mode conditions. We designed and optimized the MMI splitter using the beam propagation method (BPM). The splitter demonstrates the power splitting property with an efficiency of 86%. The excess losses for the MMI splitter are 0.52 dB and 0.50 dB for TE and TM modes, respectively, at 1.55 µm. The polarization dependence loss (PDL) and propagation loss (PL) are 0.015 dB and 0.00019 dB/µm, respectively.

The Design and Characterization of an Ultra-Compact Asymmetrical Multimode Interference Splitter on Lithium Niobate Thin Film

We propose and demonstrate a high-performance asymmetrical multimode interference splitter on X-cut lithium niobate on insulator (LNOI) with an ultra-compact size of 5.8 μm × (26.4–35.6) μm. A rectangle with a small region is removed from the upper left corner of the multimode interference (MMI) coupler to achieve a variable splitting ratio. Here, we design and characterize MMIs in six different distribution ratios ranging from 50:50 to 95:5 on a 600 nm thick LNOI. Based on the cascade structure, the linear fitting method accurately shows the device loss (~0.1–0.9 dB). Our fabricated devices demonstrate robustness across a 30 nm optical bandwidth (1535–1565 nm). In addition, we numerically simulate the Z-cut LNOI, showing that the structure corresponding to the TM mode can also achieve a good variable splitting ratio.

Step and graded-index core-based polymer multimode interference splitters for photonic integrated circuits

This paper demonstrates step-index (SI) and graded-index (GI) core-based multimode interference (MMI) splitters realized with polymer materials for photonic integrated circuits (PICs). These SI and GI index-based MMI splitters guide the input light through the multimode waveguide following the self-imaging principles and demonstrate the multiple outputs with the same uniformity when the self-imaging length is obtained. We numerically design and develop (1 ×5) MMI splitters using the beam propagation method (BPM), and we use the RSoft CAD BeamPROP solver for the structural design and waveguide characterization. The structures of the SI and GI MMI splitters are optimized by investigating the structural parameters, particularly the width and length of the multimode waveguide and the core spacing between the output ports with the maximum uniform intensity at the self-imaging length. We also compare the structural design and optical properties of the SI and GI MMI waveguides. The excess losses of the SI MMI splitter are 1.09 and 1.12 dB for transverse electric (TE) and transverse magnetic (TM) modes, respectively, while for the GI MMI splitter, the losses are 0.57 dB and 0.56 dB for TE and TM modes, respectively at 1.55 µm. The power splitting efficiency for the SI MMI splitter is 77%, and for the GI MMI splitter, it is 88%. We also investigate the polarization dependence loss (PDL) for both MMI splitters, and the losses for the SI and GI MMI splitters are 0.024 dB and 0.004 dB, respectively.

3D Polymer-Based 1 × 4 MMI Splitter.

Due to the increasing trend of photonic device miniaturisation, there is also an increased need for optical splitting in a small volume. We propose a smart solution to split light in three dimensions (3D). A 3D optical splitter based on multimode interference (MMI) for the wavelength of 1550 nm is here designed, simulated, fabricated and optimised for splitting at 1550 nm. We focus also on the possibility of its direct integration on an optical fibre. The design is focused on the use of 3D laser lithography based on the direct laser writing (DLW) process. The output characteristics are investigated by near-field measurement, where we confirm the successful 1 × 4 splitting on a 158 µm long MMI splitter.

Photonic polymeric structures and electrodynamics simulation method based on a coupled oscillator finite-difference time-domain (O-FDTD) approach.

We use femtosecond laser-based two-photon polymerization (TPP) to fabricate a 2.5D micropillar array. Using an angular detection setup, we characterize the structure's scattering properties and compare the results against simulation results obtained from a novel electrodynamics simulation method. The algorithm employs a modified formulation of the Lorentz Oscillator Model and a leapfrog time differentiation to define a 2D coupled Oscillator Finite-Difference Time-Domain (O-FDTD). We validate the model by presenting several simulation examples that cover a wide range of photonic components, such as multi-mode interference splitters, photonic crystals, ring resonators, and Mach-Zehnder interferometers.

3D Optical Splitter based on MMI

In this paper, we propose and simulate a new type of three-dimensional (3D) optical splitter based on multimode interference (MMI) for the wavelength of 1550 nm. The splitter was proposed on the square basis with the width of 20 x 20 µm2 using the IP-Dip polymer as a standard material for 3D laser lithography. We present the optical field distribution in the proposed MMI splitter and its integration possibility on optical fiber. The design is aimed to the possible fabrication process using the 3D laser lithography for forthcoming experiments.

Computer simulation study about the dependence of amorphous silicon photonic waveguides efficiency on the material quality

Amorphous silicon PECVD photonic integrated devices are promising candidates for low cost sensing applications. This manuscript reports a simulation analysis about the impact on the overall efficiency caused by the lithography imperfections in the deposition process. The tolerance to the fabrication defects of a photonic sensor based on surface plasmonic resonance is analysed. The simulations are performed with FDTD and BPM algorithms. The device is a plasmonic interferometer composed by an a-Si:H waveguide covered by a thin gold layer. The sensing analysis is performed by equally splitting the input light into two arms, allowing the sensor to be calibrated by its reference arm. Two different 1 × 2 power splitter configurations are presented: a directional coupler and a multimode interference splitter. The waveguide sidewall roughness is considered as the major negative effect caused by deposition imperfections. The simulation results show that plasmonic effects can be excited in the interferometric waveguide structure, allowing a sensing device with enough sensitivity to support the functioning of a bio sensor for high throughput screening. In addition, the good tolerance to the waveguide wall roughness, points out the PECVD deposition technique as reliable method for the overall sensor system to be produced in a low-cost system. The large area deposition of photonics structures, allowed by the PECVD method, can be explored to design a multiplexed system for analysis of multiple biomarkers to further increase the tolerance to fabrication defects.

Dielectric-loaded graphene-based plasmonic multilogic gate using a multimode interference splitter.

In this paper, we propose a multilogic gate (MLG) by utilizing a dielectric-loaded graphene-based plasmonic waveguide (DLGPW) in the mid-infrared spectral region. The proposed MLG is composed of DLGPW-based switches and multimode interference (MMI) splitters and supports three logical operations-AND, XNOR, and NOR-simultaneously. First, by proper control of the graphene surface conductivity, a graphene plasmonic on-off switch is presented, and then a 3dB MMI splitter based on a DLGPW for a wavelength of 7.8μm is designed and investigated. Our studies show that electro-optical logic gates based on DLGPWs have not been reported to date. The structure of the presented MLG is very simple and CMOS-compatible. The calculated minimum extinction ratios (ER) for AND, XNOR, and NOR logic gates are 17.53dB, 53.43dB, and 17.53dB, respectively. Also, by some modifications, this structure can act as a NAND logic gate with an ER of 55.22dB. Compact footprint, high ER, and easiness of on-chip implementation are some advantages of the presented MLG.

Monolithic InP Stokes Vector Receiver With Multiple-Quantum-Well Photodetectors

Stokes vector modulation direct-detection (SVM-DD) formats have attained special attention in the short-reach communication links to transmit multilevel signals without using costly coherent receivers. In this paper, we fabricate and experimentally demonstrate a potentially low-cost DD-based SV receiver with on-chip photodetectors (PD) on a compact InP chip. Compressively strained multiple-quantum-well PD array is monolithically integrated with the SV projection circuit, which consists of multimode interference splitter and SV rotators based on self-aligned half-ridge structure. From the photocurrent signals at three on-chip PDs, the SV of input light is retrieved successfully over the entire Poincare sphere. With potentially broad operating bandwidth of InP-based PDs, the demonstrated device may be an attractive candidate to realize low-cost and high-speed receivers for the future short-reach SVM-DD systems.

A Wide Wavelength Range of 1 × 8 Optical Power Splitter With an Imbalance of Less Than ±1.0 dB on Silicon-on-Insulator Technology

A 1 × 8 optical splitter on silicon-on-insulator technology is demonstrated with less than ±1.0 dB imbalance for a wavelength range of 300 nm, in which, a multimode interference (MMI) structure is introduced into an optical power splitter. A comparison is provided for 1 × 2 MMI splitters with and without tapers, a 1 × 2 MMI splitter with tapers is designed, fabricated and measured, which show a wider wavelength range of 300 nm with a lower imbalance of less than ±0.25 dB and a propagation loss of 3 dB.

Design and development of a new architecture of sliceable bandwidth variable transponder

Abstract In this paper we propose a new sliceable bandwidth variable transponder (SBVT) architecture with the separate analysis on the transmitter and receiver section. In transmission section we propose a distance module (DM) which is a programmable module. It divides a data stream/main stream (which employs a super-channel) into sub-stream and assigned modulation technique to each sub-stream based on their light path distance detailing the concept of sub-channel. In this paper, we have also proposed an algorithm for the distance module. Next we propose a modulation and transmission module (M&TM), where, planar light wave circuit (PLC) is used for enabling three modulation techniques (PM-16QAM, PM-QPSK and PM-BPSK). Finally, we propose the receiving section, which is designed to support three modulation techniques. It consists of two demodulator circuits, one for PM-16QAM/PM-QPSK and the other for PM-BPSK. In this proposed work, we focus on the multi-mode interference (MMI) devices (MMI coupler and MMI splitter) because of their photonic integration technology which is necessary for the implementation of SBVT. Lastly, we propose an elastic optical node architecture which removes the limitations of previously discussed node architecture for long distance communication.

Optimization of a thermally tuned silicon-based reconfigurable optical power splitter with thermal isolations

In this paper, a thermally tuned silicon-based three-channel reconfigurable multimode interference (MMI) optical power splitter with four optimized thermal isolations is proposed. Specific and flexible reconfigurable functions (1×1, 1×2, and 1×3 MMI splitters) can be achieved by thermally tuning the heaters. By using a beam propagation method, the optimum geometry of the heaters, desired refractive index changes, and phase shifts of the MMI splitter are calculated at first. The temperature distributions of the devices without and with the thermal isolations are then analyzed by using the finite element method. Thermal crosstalk between adjacent heaters is observed and the influence of the thermal isolation geometry on the thermal crosstalk is examined subsequently. The geometry of the thermal isolations is optimized based on the trade-off between the thermal tuning efficiency and optical output characteristics. Finally, satisfactory improvements with the proposed structure are demonstrated with high-thermal efficiency (the maximum power dissipation decreases reach 43.7% and 55.2% for 1×1 and 1×2 MMI splitters, respectively) and good optical output quality (the maximum excess losses are as low as 0.365, 0.388, and 0.272 dB for 1×1, 1×2, and 1×3 MMI splitters, respectively; the crosstalk is less than −21.27 and −15.54 dB for 1×1 and 1×2 MMI splitters, respectively).

Compact and low-loss asymmetrical multimode interference splitter for power monitoring applications.

This Letter presents a compact and low-loss 1×2 asymmetrical multimode interference (A-MMI) splitter in rib geometry for on-chip power monitoring at 1.55 μm, where a given alteration of the component cavity determines arbitrary values of the output power splitting ratios. The device shows reduced losses (∼0.4-0.8 dB) and robustness across a 40 nm optical bandwidth (1540-1580 nm).

Design, Fabrication and Demonstration of a 1x20 Multimode Interference Splitter for Parallel Biosensing Applications

This paper presents the experimental achievement of a silicon-on-insulator 1x20 MMI splitter andsimulation evaluations of the TE-like and TM-like mode MMI splitters for parallel biosensing applications. Device fabrication technology and optical characterisation results are provided.

Integrated photonic reservoir computing based on hierarchical time-multiplexing structure.

An integrated photonic reservoir computing (RC) based on hierarchical time-multiplexing structure is proposed by numerical simulations. A micro-ring array (MRA) is employed as a typical time delay implementation of RC. At the output port of the MRA, a secondary time-multiplexing is achieved by multi-mode interference (MMI) splitter and delay line array. This hierarchical time-multiplexing structure can ensure a large reservoir size with fast processing speed. Simulation results indicate that the proposed RC system yields better performance than previously reported ones. The achieved normalized mean square error between the system output and target sequence are 0.5% and 2.7% for signal classification and chaotic time series prediction, respectively, while the sample rate is as high as 1.3 Gbps.

Unconstrained splitting ratios in compact double-MMI couplers.

A novel guided-wave optical power coupler is presented, based on two 2x2 50/50 multimode interference splitters connected with tapered waveguides that play the role of a phase shifter. By simply changing the length of this phase shifter, these double-MMI couplers can be easily designed to get any desired splitting ratio. Results of simulations are discussed and compared with the characterizations of devices fabricated on micron-scale SOI wafers, to highlight pros and cons of the proposed solution. The fabricated splitters have been found to have average losses about 0.4 ± 0.5 dB and splitting ratios ranging from 56/44 to 96/4.

High Power Photodiodes for Microwave Applications

High Power Photodiodes for Microwave Applications

Silicon photonic devices and platforms for the mid-infrared

Due to its excellent electronic and photonic properties, silicon is a good candidate for mid-infrared optoelectronic devices and systems that can be used in a host of applications. In this paper we review some of the results reported recently, and we also present several new results on mid-infrared photonic devices including Mach-Zehnder interferometers, multimode interference splitters and multiplexers based on silicon-on-insulator, polysilicon, suspended silicon, and slot waveguide platforms.

Proposal of Compact Tunable 1×2 Multimode Interference Splitter Based on Multiple Quantum Well

We propose a compact tunable 1×2 multimode interference (MMI) splitter based on an InGaAs/InAlAs multiple quantum well for an active trimmer for Mach–Zehnder modulator with a very high extinction ratio. The light power splitting characteristics of the splitter are theoretically investigated by a beam propagation method and a three dimensional finite-difference time-domain method. It is assumed that the core layer is composed of a multiple five-layer asymmetric coupled quantum well (FACQW) that is expected to exhibit a large electrorefractive index change owing to its unique quantum confined Stark effect. By applying reverse voltages and changing slightly the refractive indices of the localized regions surrounded by trenches for electrical isolation, the power splitting ratio can be tuned over a wide range. The length and width of the proposed MMI with four refractive index modulation regions are 192 and 6 µm, respectively. The length can be reduced to 115 µm if the number of index modulation regions is reduced to two, though the tuning range of the splitting ratio is narrowed. The simulation results show that the proposed compact MMI splitter has a low insertion loss and a low power consumption, and is promising for Mach–Zehnder modulators with a very high extinction ratio.

90° SOI optical hybrid for Radio-over-fibre links

Radio-over- fibre (RoF) technology is receiving large attention due to its ability to provide simple antenna front ends, increased capacity and increased wireless access coverage. Coherently detected RoF systems would enable the information to be carried in both the amplitude and phase or in different states of the polarisation of the optical field. Additionally, the selectivity of coherent receiver is very well suited for access networks. We present a 90° optical hybrid built on a silicon-on-insulator planar light-wave circuit, which can be used as the optical front end of the digital coherent receiver in a digitised RoF link and will lead to reduced receiver footprint and cost. The optical hybrid circuit includes 2 × 2 and 4 × 4 multimode interference (MMI) splitters, in a polarisation diversity configuration. The simulation results at vacuum wavelength 1,550 nm show polarisation independence and phase errors between the ports of less than 0.03°. The properties of the prototyped 4 × 4 MMI were measured over a wide range of wavelengths. The 2 × 2 and 4 × 4 MMI showed nearly equal splitting ratios. Measurements of the relative phase relationship between the ports for Transverse Electric mode polarisation are shown to match the simulation results.