Modified Very High Frequency Research Articles

High efficiency large area a‐SiGe:H based multi‐junction solar cells using MVHF

AbstractWe have developed high efficiency large area a‐Si:H and a‐SiGe:H multi‐junction solar cells using a Modified Very High Frequency (MVHF) glow discharge process. We investigated a‐SiGe:H deposition rate dependence of cell performance, and optimized MVHF a‐SiGe:H process at a deposition rate 2‐4 times that of a typical RF deposition. We conducted a comparative study for different cell structures, and compared the initial and stable performance and light‐induced degradation of solar cells made using MVHF and RF techniques. In additon to high initial efficiency, the MVHF cells also exhibit superior light stability, showing <10% degradation after 1000 hour of one‐sun light soaking at 50 °C. We also studied light‐induced defect level and hydrogen evolution characteristics of MVHF deposited a‐SiGe:H films and compared them with the RF deposited films (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)

High Efficiency Hydrogenated Nanocrystalline Silicon Solar Cells Deposited at High Rates

AbstractWe report recent progress on hydrogenated nanocrystalline silicon (nc-Si:H) solar cells prepared at different deposition rates. The nc-Si:H intrinsic layer was deposited, using a modified very high frequency (MVHF) glow discharge technique, on Ag/ZnO back reflectors (BRs). The nc-Si:H material quality, especially the evolution of the nanocrystallites, was optimized using hydrogen dilution profiling. First, an initial active-area efficiency of 10.2% was achieved in a nc-Si:H single-junction cell deposited at ~5 Å/s. Using the improved nc-Si:H cell, we obtained 14.5% initial and 13.5% stable active-area efficiencies in an a-Si:H/nc-Si:H/nc-Si:H triple-junction structure. Second, we achieved a stabilized total-area efficiency of 12.5% using the same triple-junction structure but with nc-Si:H deposited at ~10 Å/s; the efficiency was measured at the National Renewable Energy Laboratory (NREL). Third, we developed a recipe using a shorter deposition time and obtained initial 13.0% and stable 12.7% active-area efficiencies for the same triple-junction design.

High Efficiency Large Area a-Si:H and a-SiGe:H Multi-junction Solar Cells Using MVHF at High Deposition Rate

AbstractWe have developed high efficiency large area a-Si:H and a-SiGe:H multi-junction solar cells using a Modified Very High Frequency (MVHF) glow discharge process. We conducted a comparative study for different cell structures, and compared the initial and stable performance and light-induced degradation of solar cells made using MVHF and RF techniques. Besides high efficiency, the MVHF cells also demonstrate superior light stability, showing <10% degradation after 1000 hour of one-sun light soaking at 50 °C. We also studied light-induced defect level and hydrogen evolution characteristics of MVHF deposited a-SiGe:H films and compared them with the RF deposited films.

Comparative Study of MVHF and RF Deposited Large Area Multi-junction Solar Cells Incorporating Hydrogenated Nano-Crystalline Silicon

AbstractWe report our investigations of large area multi-junction solar cells based on hydrogenated nano-crystalline silicon (nc-Si:H). We compared results from cells deposited by RF (13.56 MHz) at lower deposition rate (˜3 Å/s) and by Modified Very High Frequency (MVHF) at higher rate (≥ 10 Å/s). With optimized process conditions and cell structures, we have obtained ˜12% initial small active-area (˜0.25 cm2) efficiency for both RF and MVHF cells and 10˜11% large aperture-area (˜400 cm2) encapsulated MVHF cell efficiency for both a-Si:H/nc-Si:H double-junction and a-Si:H/nc-Si:H/nc-Si:H triple-junction structures on Ag/ZnO coated stainless steel substrate.

High efficiency amorphous and nanocrystalline silicon based multi-junction solar cells deposited at high rates on textured Ag/ZnO back reflectors

AbstractWe report our recent progress on nc-Si:H single-junction and a-Si:H/nc-Si:H/nc-Si:H triple-junction cells made by a modified very-high-frequency (MVHF) technique at deposition rates of 10-15 Å/s. First, we studied the effect of substrate texture on the nc-Si:H single-junction solar cell performance. We found that nc-Si:H single-junction cells made on bare stainless steel (SS) have a good fill factor (FF) of ˜0.73, while it decreased to ˜0.65 when the cells were deposited on textured Ag/ZnO back reflectors. The open-circuit voltage (Voc) also decreased. We used dark current-voltage (J-V), Raman, and X-ray diffraction (XRD) measurements to characterize the material properties. The dark J-V measurement showed that the reverse saturated current was increased by a factor of ˜30 when a textured Ag/ZnO back reflector was used. Raman results revealed that the nc-Si:H intrinsic layers in the two solar cells have similar crystallinity. However, they showed a different crystallographic orientation as indicated in XRD patterns. The material grown on Ag/ZnO has more random orientation than that on SS. These experimental results suggested that the deterioration of FF in nc-Si:H solar cells on textured Ag/ZnO was caused by poor nc-Si:H quality. Based on this study, we have improved our Ag/ZnO back reflector and the quality of nc-Si:H component cells and achieved an initial and stable active-area efficiencies of 13.4% and 12.1%, respectively, in an a-Si:H/nc-Si:H/nc-Si:H triple-junction cell.

Study of Large Area a-Si:H and nc-Si:H Based Multijunction Solar Cells and Materials

ABSTRACTSolar cells based on hydrogenated nanocrystalline silicon (nc-Si:H) have demonstrated significant improvement in the last few years. From the standpoint of commercial viability, good quality nc-Si:H films must be deposited at a high rate. In this paper, we present the results of our investigations on obtaining high quality nc-Si:H and a-Si:H films and solar cells over large areas using high deposition rate. We have employed the modified very high frequency (MVHF) glow discharge technique to realize high-rate deposition. Modeling studies were conducted to attain good spatial uniformity of electric field over a large area (15”×1”) MVHF cathode for nc-Si:H deposition. A comparative study has been carried out between the RF and MVHF plasma deposited a-Si:H and nc-Si:H single-junction and a-Si:H/nc-Si:H double-junction solar cells. By optimizing the nc-Si:H cell and the tunnel/recombination junctions, we have obtained an initial aperture-area (460 cm2) efficiency of 11.9% for a-Si:H/nc-Si:H double-junction cells using conventional RF (13.56 MHz) plasma deposition. The deposition rate was 3 Å/sec. Results on solar cells made with MVHF will also be presented.

High Rate Deposition of Amorphous Silicon Based Solar Cells using Modified Very High Frequency Glow Discharge

AbstractWe report our recent progress on high rate deposition of hydrogenated amorphous silicon (a-Si:H) and silicon germanium (a-SiGe:H) based n-i-p solar cells. The intrinsic a-Si:H and a-SiGe:H layers were deposited using modified very high frequency (MVHF) glow discharge. We found that both the initial cell performance and stability of the MVHF a-Si:H single-junction cells are independent of the deposition rate up to 15 Å/s. The average initial and stable active-area cell efficiencies of 10.0% and 8.5%, respectively, were obtained for the cells on textured Ag/ZnO coated stainless steel substrates. a-SiGe:H single-junction cells were also optimized at a rate of ~10 Å/s. The cell performance is similar to those made using conventional radio frequency technique at 3 Å/s. By combining the optimized component cells made at 10 Å/s, an a-Si:H/a-SiGe:H double-junction solar cell with an initial active-area efficiency of 11.7% was achieved.

Correlation between Powder in the Plasma and Stability of High Rate Deposited a-Si:H

AbstractHydrogenated amorphous silicon (a-Si:H) solar cells incorporating high deposition rate (8-10Å/s) intrinsic layers were deposited using modified very high frequency (MVHF) plasma. We have monitored the light scattered from powder generated in the plasma using an Ar-laser and a silicon photodiode. This simple, non-invasive technique allows us to make measurements on the same reactor used to make the solar cells. First, we have varied the total flow rate and observed a maximum in the scattered light intensity from powder in the plasma during the deposition of the intrinsic layer, and correlated this with the degradation, as well as the stabilized performance of the solar cells. Then, we have studied the effects of varying the deposition temperature and/or the addition of germane to the gas mixture on the scattered light intensity due to powder in the plasma.

Hydrogenated Microcrystalline Silicon Single-Junction and Multi-Junction Solar Cells

AbstractThis paper summarizes our recent studies of hydrogenated microcrystalline silicon (μc-Si:H) solar cells as a potential substitute for hydrogenated silicon germanium alloy (a-SiGe:H) bottom cells in multi-junction structures. Conventional radio frequency (RF) glow discharge is used to deposit hydrogenated amorphous silicon (a-Si:H) and μc-Si:H at low rates (∼ 1 Å/s), searching for the highest efficiency. We have achieved an initial active-area efficiency of 13.0% and stable efficiency of 11.2% using an a-Si:H/μc-Si:H double-junction structure. Modified very high frequency (MVHF) glow discharge is used to deposit a-Si:H and μc-Si:H at high rates (∼ 3-10 Å/s) for comparison with our a-Si:H/a-SiGe:H/a-SiGe:H triple-junction production technology. The deposition time for the μc-Si:H intrinsic (i) layer in the bottom cell should be less than 30 minutes in order to be acceptable for mass production. To date, an initial active-area efficiency of 12.3% has been achieved with the bottom cell deposited in 50 minutes. By increasing the deposition rate and reducing the bottom cell thickness, we have achieved an initial active-area efficiency of 11.4% with the bottom cellilayer deposited in 30 minutes. The cell stabilized to 10.4% after prolonged light soaking. We will address issues related to μc-Si:H material, solar cell design, solar cell analysis, and stability.

Hydrogenated Microcrystalline Silicon Solar Cells Made with Modified Very-High-Frequency Glow Discharge

AbstractHydrogenated microcrystalline silicon (μc-Si:H) solar cells are made using modified veryhigh-frequency (MVHF) glow discharge at deposition rates ∼3-5 Å/s. We find that the solar cells made under certain conditions show degradation in air without intentional light soaking. The short-circuit current drops significantly within a few days after deposition, and then stabilizes. We believe that post-deposition oxygen diffusion along the grain boundaries or cracks is the origin of the ambient degradation. By optimizing the deposition conditions, we have found a plasma regime in which the μc-Si:H solar cells do not show such ambient degradation. The best a-Si:H/μc-Si:H double-junction solar cell has an initial active-area efficiency of 10.9% and is stable against the ambient degradation. The stability data of the solar cells after light soaking are also presented.

Annealing Kinetics of Amorphous Silicon Alloy Solar Cells Made at Various Deposition Rates

ABSTRACTA systematic study has been made of the annealing kinetics of amorphous silicon (a-Si) alloy solar cells. The cells were deposited at various rates using H2 dilution with radio frequency (RF) and modified very high frequency (MVHF) glow discharge. In order to minimize the effect of annealing during light soaking, the solar cells were degraded under 30 suns at room temperature to quickly reach their saturated states. The samples were then annealed at an elevated temperature. The J-V characteristics were recorded as a function of annealing time. The correlation of solar cell performance and defect density in the intrinsic layer was obtained by computer simulation. Finally, the annealing activation energy distribution (Ea) was deduced by fitting the experimental data to a theoretical model. The results show that the RF low rate solar cell with high H2 dilution has the lowest Ea and the narrowest distribution, while the RF cell with no H2 dilution has the highest Ea and the broadest distribution. The MVHF cell made at 8Å/s withhigh H2 dilution shows a lower Ea and a narrower distribution than the RF cell made at 3 Å/s, despite the higher rate. We conclude that different annealing kinetics plays an important role in determining the stabilized performance of a-Si alloy solar cells.

Amorphous Silicon and Silicon Germanium Alloy Solar Cells Deposited by VHF at High Rates

ABSTRACTA modified very high frequency (MVHF) glow discharge technique is used to deposit amorphous silicon (a-Si) and amorphous silicon-germanium (a-SiGe) alloy solar cells at high deposition rates. High quality a-Si alloy solar cells have been obtained by using MVHF at deposition rates up to ∼10 Å/s. The cells show good initial and stabilized efficiencies comparable to those obtained from conventional radio-frequency (RF) glow discharge deposition at low rates (∼1 Å/s). However, high quality a-SiGe alloy solar cells are more difficult to achieve at high deposition rates. In this paper, we present the progress made on a-SiGe alloy solar cells by incorporating bandgap profiling and appropriate buffer layers. Using the improved a-SiGe alloy solar cells, a-Si/a-SiGe tandem configurations are made and results presented.

Analysis of Plasma Properties and Deposition of Amorphous Silicon Alloy Solar Cells Using Very High Frequency Glow Discharge

AbstractPositive ionic energy distributions in modified very-high-frequency (MVHF) and radio frequency (RF) glow discharges were measured using a retarding field analyzer. The ionic energy distribution for H2 plasma with 75 MHz excitation at a pressure of 0.1 torr has a peak at 22 eV with a half-width of about 6 eV. However, with 13.56 MHz excitation, the peak appears at 37 eV with a much broader half-width of 18 eV. The introduction of SiH4 to the plasma shifts the distribution to lower energy. Increasing the pressure not only shifts the distribution to lower energy but also broadens the distribution. In addition, the ionic current intensity to the substrate is about five times higher for MVHF plasma than for RF plasma. In order to study the effect of ion bombardment, the deposition of a-Si alloy solar cells using MVHF was investigated in detail at different pressures and external biases. Lowering the pressure and negatively biasing the substrate increases ion bombardment energy and results in a deterioration of cell performance. It indicates that ion bombardment is not beneficial for making solar cells using MVHF. By optimizing the deposition conditions, a 10.8% initial efficiency of a-Si/a-SiGe/SiGe triple-junction solar cell was achieved at a deposition rate of 0.6 nm/sec.