Mm In Diameter Research Articles

Nilai kekerasan permukaan pada beberapa tipe beton dengan agregat buatan dan korelasinya terhadap kuat tekan

Along with the development of technology to utilize waste in order to create sustainable concrete materials; therefore, this research tries to apply several artificial aggregates derived from concrete waste and fly ash. The test object was a standard concrete cylinder measuring 150 mm in diameter and 300 mm in height. Concrete was made from geopolymer coarse aggregate, treated recycled coarse aggregate, and conventional coarse aggregate. The surface hardness value was measured using a hammer test to obtain the rebound number (RN). Tests were also conducted on concrete with natural aggregate. The results show that the RN value of treated recycled coarse aggregate concrete is in the second place after normal aggregate concrete, followed by the RN value of conventional recycled coarse aggregate. Concrete with geopolymer coarse aggregate is concluded to be lightweight low strength concrete based on the RN value and compressive strength obtained. Furthermore, the relationship between RN values and compressive strength for other concretes is shown by the correlation of y = 0.837 x + 3.627, where y is the concrete compressive strength (MPa) and x is the surface hardness value (RN).

Effect of Bovine Lactoferrin Treatment on Iron Homeostasis and Gene Expression Changes in Multiple Organ Dysfunctions During Wound Healing Process in Rats.

Injury systemically disrupts the homeostatic balance and can cause organ failure. LF mediates both iron-dependent and iron-independent mechanisms, and the role of LF in regulating iron homeostasis is vital in terms of metabolism. In this study, we evaluated the organ-level effect and gene expression change of bLf in the cutaneous repair process. An excisional full-thickness skin defect (FTSD) wound model was created in male Sprague Dawley rats (180-250 g) (n = 48) fed a high-fat diet (HFD) and the PHGPx, SLC7A11 and SLC40A1 genes and iron metabolism were evaluated. The animals were randomly divided into 6 groups: 1- Control, 2- bLf (200 mg/kg/day, oral), 3- FTSD (12 mm in diameter, dorsal), 4- HFD + bLf, 5- HFD + FTSD, 6- HFD + FTSD + bLf. Histologically, iron accumulation was demonstrated by Prussian blue staining in the liver, kidney, and intestinal tissues. Gene expression analysis was performed with qPCR. Histologically, iron accumulation was demonstrated by Prussian blue staining in the liver, kidney, and intestinal tissues. Prussian blue reactions were detected in the kidney. PHPGx and SLC7A11 genes in kidney and liver tissue were statistically significant (P < 0.05) except for the SLC40A1 gene (P > 0.05). Expression changes of the three genes were not statistically significant in analyses of rat intestinal tissue (P = 0.057). In the organ-level ferroptotic damage mechanism triggered by wound formation. BLf controls the expression of three genes and manages iron deposition in these three tissues. In addition, it suppressed the increase in iron that would drive the cell to ferroptosis and anemia caused by inflammation, thereby eliminating iron deposition in the tissues.

Experiments and Theory on Droplet Ignition with Spark Discharges

ABSTRACT Ignition experiments were performed with individual n-decane droplets, initially, about 1 mm in diameter, which were suspended in quartz fibers and subjected to electrical discharges (sparks) of controlled power and duration. Experiments were performed with glow and arc discharges in air at 1 atm and approximately 300 K . Theory is developed to predict the probability of ignition of a fuel droplet as a function of time when it is exposed to an ignition spark. The theory considers the effect of random spark-to-spark fluctuations in the heat flux into the liquid on the time for the droplet surface temperature to be high enough to enable ignition. A Bayesian analysis is also performed to evaluate confidence intervals for parameters related to droplet ignition. Reasonable agreement between theory and experiment is demonstrated, suggesting that spark-to-spark fluctuations of the heat flux into a droplet may lead to a sigmoidal variation of the probability of ignition with respect to time.

Analysis of osseointegration of implants with macrogeometries with healing chambers: a randomized clinical trial

BackgroundTo verify the influence of macrogeometry with healing chambers on the osseointegration of dental implants by analyzing implant stability quotient (ISQ) and evaluate the correlation between insertion torque and ISQ insertion with different macrogeometries.MethodsIn total, 26 implants were installed in the posterior mandible of eight patients with sufficient bone height for the installation of implants measuring 3.5 mm in diameter and 9.0 mm in length. The implants were categorized according to two types of macrogeometry: a test group (GT) with 13 conical implants with healing chambers and a control group (GC) with 13 conical implants with conventional threads. To insert the implants, a bone drilling protocol was used up to a diameter of 3 mm with the last helical bur. The insertion torque of the implants was evaluated, followed by the measurement of ISQ at 0 (T-0), 7 (T-7), 14 (T-14), 21 (T-21), 28 (T-28), and 42 (T-42) days.ResultsThe mean insertion torque was 43 Ncm in both groups, without a significant difference. Moreover, no significant difference in the ISQ values was found between the groups at different time points (p > 0.05), except at T-7 (GT = 69.87±1.89 and GC = 66.48±4.49; p = 0.01). Although there was no significant difference, ISQ median values were higher in the GT group than GC group at 28 days (GT = 67.98 and GC = 63.46; p = 0.05) and 42 days (GT = 66.12 and GC = 60.33; p = 0.09). No correlation was found between the insertion torque and ISQ insertion (p > 0.05).ConclusionFurthermore, implants with a 3.5 mm diameter macrogeometry, with or without healing chambers, inserted with a drilling protocol up to 3 mm in diameter of the last helical bur, led to a similar secondary stability, with no difference in ISQ values. Although, implants with healing chamber demonstrates ascending values in the graph of ISQ, having a trend of faster osseointegration than implants without healing chambers. Both macrogeometries provide a similar primary stability to implants.Trial registrationThis study was registered retrospectively in ReBec (brazilian registry of clinical trials) under the number RBR-96n5×69, on the date of 19/06/2023.

Transforming acoustic control: The first tunable broadband origami-based Helmholtz resonator

Abstract Helmholtz resonators have long been essential for acoustic control,&amp;#xD;enhancing or nullifying sound at specific frequencies. Traditionally, these resonators are&amp;#xD;effective for fixed-frequency applications, but lose efficacy if the excitation frequency&amp;#xD;changes. This paper presents the first tunable broadband origami-based Helmholtz&amp;#xD;resonator, featuring a compliant origami design with auxetic properties for optimal&amp;#xD;volume variation. Multiphysics simulations determined the adaptive cavity geometry,&amp;#xD;and experimental tests validated the models, showing high tunability (up to 25%&amp;#xD;around a central frequency of 461 Hz with a 95% absorption rate) and broad bandwidth&amp;#xD;(up to 13% around the central frequency with a 95% absorption rate) with minimal&amp;#xD;geometry variation (8 mm in diameter). This work marks a significant advancement&amp;#xD;over traditional Helmholtz resonators.

First Report of Rhizoctonia solani AG 4 HG-III Causing Stem Lesion of Watermelon in Idaho.

In July 2022, stem lesions, approximately 4 to 5 cm in length as well as leaf wilt and dark brown necrosis on stems and roots were observed in two fields in Southwest Idaho on 20 to 30% of watermelons (Citrullus lanatus). To determine the causal agent, isolations were attempted from symptomatic tissue. The surface of the affected material was disinfected with 0.6% sodium hypochlorite for 1 min and rinsed three times with sterile water. Approximately 2 mm3 sections of tissue were plated on water agar amended with 0.02% penicillin and 0.08% streptomycin and incubated at room temperature for 7 days. Fungal colonies were tentatively identified as Rhizoctonia from right-angle branching and septate hyphal structures, slight constriction and septum near the branch base, and the production of 1 to 2 mm white to light brown irregularly shaped sclerotia. Single hyphal tips were transferred to potato dextrose agar (PDA) and grown at room temperature. Approximately ten isolates from each field with a consistent macromorphology were observed. These isolates had light brown mycelia, produced sclerotia at ambient temperature with no exposure to continuous light, and a representative isolate, designated D22-110 was selected for sequencing and pathogenicity testing. For isolate D22-110, mycelia were removed with a scalpel after 7 days of growth, for DNA extraction and sequencing of the rDNA internal transcribed spacer (ITS) region as previously described (White et al., 1990). A 726 bp product was generated and the sequence was submitted to GenBank (Accession No. OQ794049). NCBI-BLAST indicated this sequence was 99% identical (631 of 634 bp and 632 of 634 bp identical) with known reference isolates previously identified as R. solani AG 4 HG-III (Accession No. AF354075 and AF354076, respectively) from a phylogenetic study (Gonzalez et al., 2001). Pathogenicity testing was performed twice on two-week-old seedlings of watermelon cultivars Endless Summer and Wingman in greenhouse conditions (29oC, 12 h daylight). Two disks (3 mm diam) from 7-day-old plates of PDA were placed around each seedling at the root and stem convergence point. Ten seedlings were mock-inoculated with sterile PDA plugs as a control. Approximately 35% damping-off incidence was observed on inoculated seedlings six days post-inoculation, while control seedlings remained healthy. At 20 days post-inoculation, 20 (first trial) and 34 seedlings (second trial) were assessed for visible stem and root lesions. Incidence of stem lesions occurred on 90% of seedlings, with 80% of seedlings possessing lesions greater than 10 mm in diameter. Seedlings without R. solani inoculation were free of stem and root lesions. R. solani was re-isolated from symptomatic tissue, with 40% frequency of isolation, identified by right-angle branching of the hyphae thus confirming Koch's postulates. R. solani AG 4 has been reported in watermelon in the US since 1994 (Hall and Summer, 1994) but the AG 4 subgroup was not reported. AG 4 HG-III was reported in melon seedlings causing damping-off in Kyrgyzstan (Erper et al. 2016). In other hosts, AG 4 HG-III was found in potatoes in South Africa (Muzhinji et al., 2014), buckwheat and foxtail millet in China (Zhou et al., 2015; Hao et al., 2023), broccoli and spinach (Kuramae et al., 2003) and turnip green (Sekiguchi et al., 2015). To the best of our knowledge, this is the first report of R. solani AG 4 HG-III causing disease in watermelon in Idaho. Given the the rate of disease incidence observed in the field, growers should consider avoiding planting alternative host crops to minimize inoculum buildup.

Abstract B053: SUMOylation and TIGIT inhibition: a novel immunotherapy combination for pancreatic cancer

Abstract Introduction: Immune checkpoint inhibitors have shown promise in many other solid tumors but have been disappointing in pancreatic ductal adenocarcinoma (PDAC). Preclinical work demonstrates that the immune checkpoint receptor TIGIT plays a key role in PDAC immune evasion and may be a better therapeutic target than the PD1 or CTLA4 axes. Post-translational small-ubiquitin-like modification (SUMOylation) regulates the activity of numerous proteins involved in cell proliferation. Our laboratory has shown that inhibition of SUMOylation with small molecule TAK-981 favorably modulates the PDAC immune microenvironment and specifically increases the expression of TIGIT binding partners CD226 on immune cells and CD155 on tumor cells. We hypothesized that inhibition of SUMOylation with small molecule TAK-981 would synergize with anti-TIGIT antibody therapy to induce anti-tumor immunity. Methods:All studies utilized a murine PDAC organoid line (KPC46) derived from a liver metastasis in a genetically engineered mouse model (KPC). KPC46 consistently metastasizes to the liver when implanted orthotopically into the tail of the pancreas in immunocompetent mice. Following tumor implantation, mice were surveilled by ultrasound until tumors reached 5-7 mm in diameter, then randomized to one of two treatment groups: TAK-981 + anti-TIGIT or vehicle control (n=10/group). Monotherapies were not included, as each drug alone did not produce significant responses in prior studies using this model. The treatment cohort received 15 mg/kg of TAK-981 and 100 micrograms of anti-TIGIT antibody via intraperitoneal injection every 48 hours starting 14 and 15 days, respectively, post-implantation, for a total of 4 weeks. Complete responders were defined as absence of disease after 2 months of observation. Complete responders and age-matched controls (n=3/group) were rechallenged with subcutaneous tumor injection and monitored for tumor development. Results:Survival of PDAC mice was significantly prolonged in the combination group when compared to the control group (median survival 81 vs 42 days, P&amp;lt;0.05). A total of 4 mice (40%) were deemed complete responders after 2 months of monitoring. The re-challenge experiment produced tumors in all three control mice but none of the treated mice by 4 weeks after implantation. Conclusion:In this study, we explored the combination of two promising immunotherapy agents for PDAC which demonstrated significant additive effects generating durable and complete responses. We were able to confirm the presence of protective immunity. These results are rarely seen in PDAC experiments. Further experiments to better understand and optimize these effects are underway. These drugs are currently in clinical trials for solid tumors and could feasibly be studied in the near future in PDAC. Citation Format: Jorge R de la Torre Medina, Utsav Joshi, Jaynath Shankara Narayanan, Herve Tiriac, Yuan Chen, Rebekah White. SUMOylation and TIGIT inhibition: a novel immunotherapy combination for pancreatic cancer [abstract]. In: Proceedings of the AACR Special Conference in Cancer Research: Advances in Pancreatic Cancer Research; 2024 Sep 15-18; Boston, MA. Philadelphia (PA): AACR; Cancer Res 2024;84(17 Suppl_2):Abstract nr B053.

Simulating the Rising Air Bubbles Stream through Heavy Fuel Oil Residue Bubble Column Reactor using COMSOL

Several industrial operations rely on the rise of air bubbles through heavy fuel oil residue (HFOr), including oil recovery and wastewater treatment. In order to increase efficiency and decrease expenses, it is necessary to understand the peculiarities of this process. With the help of COMSOL Multiphysics, we numerically simulate the ascent of a single air bubble via HFOr in this article. The dimensions of the container used in the simulations were (100) mm in diameter and (200) mm in height, with an air bubble diameter of 4.5 mm. For an air bubble ascending through an HFOr column, the predicted numerical outcomes are contrasted with nine experimental versions. As the bubble rose higher, the region with the greatest number of vortices was located on its side. The remaining vortex is contained inside the bubble. In addition, since drag decreases the flow, a lighter fluid usually exhibits a region of strong vortex and low pressure. Because of the oscillation effect, the results reveal that the rising velocity initially rises and then gradually falls between 0.6 and 0.65 s. The air bubbles' wavy motion is caused by the high fluid density, which becomes worse as the air velocity gets higher. The values of the drag coefficient rise sharply with decreasing air extrusion speed. It turns out that the height of the fluid has an inverse relationship with the pressure.

Germanium Single Crystals for Photonics

Germanium (Ge) is a system-forming material of IR photonics for the atmospheric transparency window of 8–14 µm. For optics of the 3–5 µm range, more widespread silicon (Si), which has phonon absorption bands in the long-wave region, is predominantly used. A technology for growing Ge single crystals has been developed, allowing the production of precision optical parts up to 500 mm in diameter. Ge is used primarily for the production of transparent optical parts for thermal imaging devices in the 8–14 µm range. In addition, germanium components are widely used in a large number of optical devices where such properties as mechanical strength, good thermal properties, and climatic resistance are required. A very important area of application of germanium is nonlinear optics, primarily acousto-optics. The influence of doping impurities and temperature on the absorption of IR radiation in germanium is considered in detail. The properties of germanium photodetectors are reported, primarily on the effect of photon drag of holes. Optical properties in the THz range are considered. The features of optical properties for all five stable isotopes of germanium are studied. The isotopic shift of absorption bands in the IR region, caused by phonon phenomena, which was discovered by the authors for the first time, is considered.

Extensive aortic replacement including aortic arch for a mega aorta with chronic aortic dissection via posterolateral thoracotomy

BackgroundMega-aortic syndrome including aortic arch and descending aortic aneurysm is a challenging surgical case. Because the aorta continuously dilates, creating the distal anastomosis sites becomes an issue. Despite the developments in endovascular techniques including frozen elephant trunk, in the case of mega-aortic syndrome or mycotic aneurysm, extensive surgical repair is still a strong armamentarium. Our patient had a mega-aorta with chronic aortic dissection. Herein, we show tips regarding concurrent ascending, aortic arch, and descending aortic replacement via posterolateral thoracotomy for this relatively young patient.Case presentationA 46-year-old man with chronic kidney disease had chronic type A aortic dissection with an extensively dilated thoracic aorta from the distal ascending to the descending aorta measuring 63 mm in diameter and abdominal aorta measuring 50 mm. The short segment of the distal descending aorta was narrowed to 36 mm. The patient underwent a concurrent replacement of the distal ascending aorta, aortic arch, and descending aorta via a posterolateral thoracotomy. The patient was extubated on postoperative day (POD) 1 and discharged home without serious complications such as stroke, respiratory failure, or renal failure on POD 18. The 1-year follow-up computed tomography did not find issues in the anastomosis sites; however, the abdominal aorta enlarged from 50 to 58 mm. The patient underwent a thoracoabdominal aortic replacement and recovered well without any complications.ConclusionsGood exposure and meticulous organ protection methods are key to a safe concurrent replacement of the ascending, aortic arch, and descending aorta via posterolateral thoracotomy.

Microfluidics and Chip Development

During the course of the summer, I had the privilege to work with Dr. Carlos Escobedo and his team of researchers on the topics of microfluidics and Lab-On-Chip (LOC) technology. Microfluidics is a branch of fluid dynamics which utilizes small volumes of fluid to perform tests under ideal conditions, and LOC is the process of using microfluidics for experiments in small-scale environments. I participated in two LOC projects, the first for bacterial analysis and the second for microplastic separation. The goal of the first project was to observe if Vibrio Cholerae bacteria was attracted to a variety of chemo attractants. To observe this interaction under microfluidic conditions, we developed a chip which when flooded with chemoattractant trapped a portion in the chip. We could then remove the non-entrapped chemoattractant from the sides and refill the chip with bacteria. Observations of the bacteria’s movement were then taken using a microscope attached to a digital camera. The second project focused on microplastics, which are plastic particulates under 5mm in diameter, our smallest sample being 10μm. Due to their size standard filtering techniques were ineffective at separating them, which led to us using Deterministic Lateral Displacement (DLD). DLD utilizes an array of pillars to create spots of changing pressure for passing particles. The array is designed so larger particles are unaffected while smaller particulates will be redirected and collected separately. To arrange the plastics into their types, a centrifugal design was used. This design functions similarly to a centrifuge, which by rapidly spinning a substance separates out materials based on density. The chip works under a similar theory, but instead uses a spiral channel to force the particles in a repeated circular spinning motion. The particles then exit with differing directionalities based on where they were in the channel, allowing for collection.

Prediction of immediate bleeding after cold snare polypectomy: A prospective observational study.

The risk factors for immediate post-polypectomy bleeding (IPPB) after cold snare polypectomy (CSP) are not well-known. We sought to define such risk factors and develop a predictive risk-scoring model. This prospective observational study included 161 polyps (4-9 mm in diameter) that were removed via CSP from 118 patients during the period from June to September 2019 in 2 tertiary hospitals. IPPB was defined as post-polypectomy bleeding within 24 hours or grade 3 or 4 intraprocedural bleeding requiring endoscopic hemostasis. IPPB incidences according to grade were 13.0% (21/161) (grade 3) and 0% (grade 4). Univariate analysis showed that the polyp size and morphology, as well as iatrogenic ulcer size and shape, were significantly associated with IPPB. Multivariate analysis showed that polyp size [6-9 mm vs 4-5 mm, odds ratio (OR) 3.72, 95% confidence interval (CI) 1.28-10.79], polyp morphology (polypoid vs non-polypoid, OR: 3.93, 95% CI: 1.22-12.64), and iatrogenic ulcer size (≥10 vs ≤ 9 mm, OR: 3.12, 95% CI: 1.04-9.38) were significantly associated with IPPB. We created a four-marker risk-scoring model to predict IPPB after CSP; we summed the points assigned for the 4 factors. At a cutoff of 2, the sensitivity was 85.7% and the specificity was 65.0%; at a cutoff of 3, the sensitivity was 65% and the specificity was 90.0%. Polyp size and morphology, as well as iatrogenic ulcer size and shape, were associated with IPPB after CSP. The four-marker risk-scoring model appears to effectively predict IPPB after CSP (Clinical Research Information Service: KCT0004375).

Microwave Plasma Pencil for Surface Treatment: Numerical Study of Electromagnetic Radiation and Experimental Verification.

An atmospheric pressure plasma source of the microwave plasma pencil type utilizing a coaxial line is presented. The generated plasma takes the form of a cylinder up to about 30 mm long and up to 5 mm in diameter. It is suitable for surface sterilization, surface treatment, and material processing. This study numerically analyzes the electromagnetic radiation emitted by the plasma pencil, which compromises performance and poses safety risks. Electric field distributions, radiation patterns, the ratio of the power entering the discharge to the incident wave power, and the ratio of radiated power to entering power were numerically investigated for different plasma parameters and pencil lengths. Results indicate that increasing electron density, gas temperature, plasma length, and pencil length increases the radiated power by up to more than 60% of the entering power, and the radiation patterns can be highly non-uniform with strong backward lobe. The numerical finding were qualitatively confirmed experimentally. It was also found that it is possible to reduce radiation from the device by using appropriately designed cones, the presence of which does not impede its performance.

Diagnosis and Surgical Removal of a Corneal Dermoid in a Red-eyed Tree Frog, Agalychnis callidryas (Anura, Hylidae), From the Tenorio Volcano, Costa Rica

Abstract A male, red-eyed frog (Agalychnis callidryas) was collected from the Tenorio Volcano region in Costa Rica due to the presence of a unilateral ocular abnormality affecting its left eye. Approximately 70% of the cornea was replaced by a well demarcated, 5.0 mm in diameter, opaque, bright green and roughened tissue compatible with skin. The affected eye was enucleated under established ophthalmic surgical procedures. A dermoid was confirmed by histopathology based on the finding of amphibian cutaneous (epidermal and dermal) tissue replacing the cornea and characterized by the presence of keratinized epidermis, spongy dermis, and integumentary glands. After a successful post-operative recovery period the frog was released back to the wild, demonstrating the viability of medical intervention and surgery in wild amphibians. Dermoids are congenital lesions that result from a failure in the differentiation of the superficial ectoderm to generate normal corneal epithelium and the subsequent development of epidermis and dermal tissues in the area. Corneal dermoids have been reported in horses, cattle, sheep, wildebeest, pigs, rats, dogs, cats, birds, and humans, this being the first case reported in amphibians. In the locality where the frog was found, several other ophthalmic abnormalities have been documented in other amphibians. Active monitoring of wild amphibians is ongoing, and possible causes of ophthalmic abnormalities in the area are being investigated.

Dynamics of Snowflakes Impacting Superhydrophobic Surfaces.

Snow and ice accumulation on surfaces presents significant safety and efficiency challenges across various industries, necessitating the development of effective mitigation strategies. In this study, the dynamics and energy dissipation of natural snowflakes impacting superhydrophobic surfaces (SHS) were explored using high-speed imaging and a novel image processing method. The size, velocity (impact and bounce), and contact time of natural wet snowflakes were quantitatively analyzed, identifying two primary impact outcomes: bouncing and fragmentation. The analysis focused on bouncing to study the coefficient of restitution (COR) of snowflakes. It was found that small snowflakes (<1.40 mm in diameter) with low impact velocities (<2.90 m/s) tend to be bounced, whereas larger, faster snowflakes are more likely to be fragmented. For the first time, the contact time of natural snowflakes on SHS was also reported, introducing a dimensionless contact time (DCT) for quantifying energy dissipation during the impact. The results indicate that energy dissipation has a cubic relationship with snowflake size and a quadratic relationship with its impact velocity, demonstrating that larger and faster snowflakes dissipate more energy. It is observed that a reduction in DCT leads to an exponential increase in COR and a decrease in normalized energy dissipation, supporting the theoretical prediction that the COR approaches one and the normalized energy dissipation approaches zero as the DCT approaches zero. These results are significant for enhancing the design and efficiency of anti-icing surfaces, contributing to the development of models that simulate snow accumulation behaviors and inform better design of both active and passive snow mitigation strategies.

MINIMALLY INVASIVE TREATMENT OF MECHANICAL STOMACH SUTURE FAILURE IN PATIENTS AFTER LONGITUDINAL RESECTION FOR OBESITY (A CLINICAL CASE)

Sleeve gastrectomy has now become one of the most popular operations in the treatment of morbid obesity. We present a clinical case of minimally invasive treatment of early suture failure after sleeve gastrectomy, from the archive of the authors’ clinical observations. Suture failure occurred on the day 4 after surgery. Endogastroscopy revealed a defect of 12 mm in diameter with infiltration at the edges. The technique of endoscopic sanitation of the abscess cavity and transcutaneous drainage of the abdominal cavity was used. After 14 days, the drainage in the abdominal cavity stopped functioning. Fistulography showed that it was not in the abscess cavity; according to endoscopic fistulography, hermetic sealing was achieved. After 2 months the fistula was completely closed. The patient was discharged with complete recovery. After 6 months, EGD revealed cicatrical changes; body weight loss: 55 kg. This clinical case demonstrated the possibility of combined minimally invasive treatment of a postoperative complication – gastric suture failure after sleeve gastrectomy.

The healing effect of nano emulsified Plantago major L extract on oral wounds in a wistar rat model

IntroductionOral lesions are a common clinical symptom arising from various etiologies and disrupt the patient’s quality of life. However, no definite treatment is not yet possible, due to the constantly changing environment of the mouth. In recent years, herbal treatments have gained popularity among patients and physicians due to their availability, safety, affordability, and antimicrobial properties. This research aims to investigate the therapeutic effects of a nano-emulsion of Plantago major standardized extract (PMSE) on oral ulcers in a Wistar rat model using histomorphometry and stereological parameters.Materials and MethodsThe study involved 72 Wistar rats divided randomly into 24 groups of 3 each: groups A1 to A4 received one dose to 4 doses of 5% PMSE nano emulsion, groups B1 to B4 received one dose to 4 doses of 10% PMSE nano emulsion, and groups C1 to C4 received one dose to 4 doses of 20% PMSE nano emulsion, groups D1 to D4 received one dose to 4 doses of nano-emulsion without PMSE, groups E1 to E4 received one dose to 4 doses of PMSE, and group F served as the control group. An incision measuring 2 mm in diameter was made in the animals’ hard palate using a biopsy punch. A swab containing the necessary material was used to administer the medication orally to the wound. Histological samples were collected on days 2, 4, 6, and 8 and sent to the pathology laboratory for examination. Data analysis was performed using SPSS 26 and setting statistical significance at p < 0.05.ResultsGroup A showed a high rate of complete and normal re-epithelialization of the wound at 66.7%, compared to the other groups. Group D had a re-epithelialization rate of 50%, while groups C, E, and F had rates of 7.41% and group B had 7.16%. In terms of inflammation reduction, 23.88% of group A had no inflammation, a higher percentage compared to the other groups. Group B and D had no inflammation in 3.33% of cases, lower than the other groups. The study evaluated frequency of re-epithelialization and inflammation levels in different groups on days 2, 4, 6, and 8 after four doses of the drug with no significant differences found among the groups.ConclusionNone of the nano emulsions or PMSE enhanced the healing rate of oral ulcers. However, a 5% PMSE nano emulsion displayed an increase in lesion re-epithelialization.

Fuchs’ Endothelial Corneal Dystrophy evaluation using a high-resolution wavefront sensor

This study aims to evaluate the applicability of the high-resolution WaveFront Phase Imaging Sensor (WFPI) in eyes with Fuchs’ Endothelial Corneal Dystrophy (FECD) through qualitative and quantitative analysis using a custom-designed Automatic Guttae Detection Method (AGDM). The ocular phase was measured using the t·\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\cdot$$\\end{document}eyede aberrometer and then was processed to obtain its High-Pass Filter Map (HPFM). The subjects were pathological and healthy patients from the Fundación Jiménez-Díaz Hospital (Madrid, Spain). The AGDM was developed and applied in pupils with 3 and 5 mm of diameter. A set of metrics were extracted and evaluated like the Root-Mean-Square error (RMS), Number of guttae, Guttae Area, and Area of Delaunay Triangulation (DT). Finally, a Support Vector Machine (SVM) model was trained to classify between pathological and healthy eyes. Quantitatively, the HPFM reveals a dark spots pattern according to the ophthalmologist’s description of the slit-lamp examination of guttae distribution. There were significant statistical differences in all the metrics when FECD and Healthy groups were compared using the same pupil size; but comparing both pupil sizes for the same group there were significant differences in most of the variables. This sensor is a value tool to objectively diagnose and monitor this pathology through wavefront phase changes.

Recruitment of the Basket Star Astrospartus mediterraneus (Risso, 1826) (Ophiuroidea, Gorgonocephalidae)

The occurrence and abundance of Astrospartus mediterraneus (Risso, 1826) have significantly increased in the last three decades in several areas of the Mediterranean Sea. In the Tavolara–Punta Coda Cavallo Marine Protected Area (NE Sardinia, Tyrrhenian Sea, Mediterranean Sea), 60 specimens were observed mainly on the granitic shoals of the Tavolara Channel, an area characterized by very intense currents and high sedimentation. The basket stars were mainly found living as epibionts of gorgonians (Eunicella verrucosa, Paramuricea clavata and Leptogorgia sarmentosa) and massive sponges (Spongia officinalis, S. lamella, Sarcotragus foetidus). We also documented 21 small specimens (3–20 mm in diameter of the oral disc) observed in June 2024 between 27 and 52 m depth on E. verrucosa and P. clavata colonies. The bimodal size-frequency distribution of these specimens suggested that, probably, specimens belong to two different reproductive events occurring in spring 2023 and 2024.

Volumetric changes of the enteric nervous system under physiological and pathological conditions measured using x-ray phase-contrast tomography.

Full-thickness biopsies of the intestinal wall may be used to study and assess damage to the neurons of the enteric nervous system (ENS), that is, enteric neuropathy. The ENS is difficult to examine due to its localization deep in the intestinal wall and its organization with several connections in diverging directions. Histological sections used in clinical practice only visualize the sample in a two-dimensional way. X-ray phase-contrast micro-computed tomography (PC-μCT) has shown potential to assess the cross-sectional thickness and volume of the ENS in three dimensions (3D). The aim of this study was to explore the potential of PC-μCT to evaluate its use to determine the size of the ENS. Full-thickness biopsies of ileum obtained during surgery from five controls and six patients clinically diagnosed with enteric neuropathy and dysmotility were included. Punch biopsies of 1 mm in diameter and 1 cm in length, from an area containing myenteric plexus, were extracted from paraffin blocks, and scanned with synchrotron-based PC-μCT without any staining. The microscopic volumetric structure of the neural tissue (consisting of both ganglia and fascicles) could be determined in all samples. The ratio of neural tissue volume/total tissue volume was higher in controls than in patients with enteric neuropathy (P = 0.013). The patient with the longest disease duration had the lowest ratio. The assessment of neural tissue can be performed in an objective, standardized way, to ensure reproducibility and comparison under physiological and pathological conditions. Further evaluation is needed to examine the role of this method in the diagnosis of enteric neuropathy.