Mixture Of HMX Research Articles

Reactivity of high active aluminum powder with RDX and HMX mixtures

In order to reveal the interaction law of high active aluminum powder with RDX and HMX mixture, the thermal decomposition behavior of highly active Al powder and its interaction with typical nitramine explosive RDX and HMX were studied by differential scanning calorimetry (DSC), thermogravimetry (TG), thermo-mass spectrometry (TG-DTG-DSC-MS) and CO2 laser ignition technology. Results show that when the nanometer aluminum powder and RDX and HMX respectively, two typical nitramine explosive mixing action is of little influence on the mixing action to respond to the thermal decomposition of HMX, depress RDX points liberation degree of temperature, both the thermal decomposition process of mixed system for random nucleation and subsequent growth process, the ignition delay time decreases with the increase of laser ignition power density. The ignition delay time and ignition energy of the mixture of high active aluminum powder and RDX are greater than that of the mixture of high active aluminum powder and HMX and the high active aluminum powder.

Thermal decomposition and kinetics of plastic bonded explosives based on mixture of HMX and TATB with polymer matrices

Abstract This work describes thermal decomposition behaviour of plastic bonded explosives (PBXs) based on mixture of l,3,5,7-tetranitro- 1,3,5,7-tetrazocane (HMX) and 2,4,6- triamino-1,3,5-trinitrobenzene (TATB) with Viton A as polymer binder. Thermal decomposition of PBXs was undertaken by applying simultaneous thermal analysis (STA) and differential scanning calorimetry (DSC) to investigate influence of the HMX amount on thermal behavior and its kinetics. Thermogravimetric analysis (TGA) indicated that the thermal decomposition of PBXs based on mixture of HMX and TATB was occurred in a three-steps. The first step was mainly due to decomposition of HMX. The second step was ascribed due to decomposition of TATB, while the third step was occurred due to decomposition of the polymer matrices. The thermal decomposition % was increased with increasing HMX amount. The kinetics related to thermal decomposition were investigated under non-isothermal for a single heating rate measurement. The variation in the activation energy of PBXs based on mixture of HMX and TATB was observed with varying the HMX amount. The kinetics from the results of TGA data at various heating rates under non-isothermal conditions were also calculated by Flynn–Wall–Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods. The activation energies calculated by employing FWO method were very close to those obtained by KAS method. The mean activation energy calculated by FWO and KAS methods was also a good agreement with the activation energy obtained from single heating rate measurement in the first step decomposition.

Mechanical and Explosive Properties of Plastic Bonded Explosives Based on Mixture of HMX and tAtB

This paper describes formulation of plastic bonded explosives (PBXs) compositions based on 2,4,6- triamino-1,3,5-trinitrobenzene (TATB), Octahydro l,3,5,7-tetranitro- 1,3,5,7-tetrazocine (HMX) by varying their relative amounts with Viton A as polymeric binder by slurry coating technique. These PBXs compositions are studied for mechanical and detonic properties. It has been observed that sensitivity and explosive performance of PBXs based on mixture of HMX and TATB were varied over a wide considerable range by varying relative amounts of TATB and HMX. The detonation study revealed there was increased in velocity of detonation (VOD) and detonation pressure with increasing amount of HMX from 10-80 % by weight. The sensitivity test results exhibited that insensitivity to impact for PBXs compositions was found to decrease with increasing HMX amount. Friction sensitivity study showed that no reactions were observed upto 36 kg load for PBXs compositions namely HT6030, HT5040, HT4050, HT3060, HT2070 and HT1080. The compressive strength of these PBXs compositions was found within the range of 9-11 MPa. Defence Science Journal, 2013, 63(6), pp.622 -629 , DOI:http://dx.doi.org/10.14429/dsj.63.5764

Analysis of Solid Explosion Products of Mixtures Based on HMX and Peroxide Benzoyl with Aluminum

The explosive transformation of mixtures of HMX and benzoyl peroxide with aluminum was studied. Aluminum oxides formed during initiation of an impact explosion were investigated. An x-ray analysis showed that aluminum is not oxidized during explosion of its mixtures with benzoyl peroxide. An analysis was made of aluminum oxides formed during explosion of HMX mixtures with aluminum hydride and ternary mixtures of aluminum, HMX, and benzoyl peroxide. It was found that the state of aluminum introduced into the composition and the explosion temperature influence the structure of aluminum oxide (Al8/3O4), whose lattice is a derivative of the spinel lattice.

Remediating munitions-contaminated soil with zerovalent iron and cationic surfactants.

Soils contaminated from military operations often contain mixtures of HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine), RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine), and TNT (2,4,6-trinitrotoluene) rather than a single explosive. Differences among explosives in solubility and reactivity make developing a single remediation treatment difficult. When Fe(0) was used to treat a munitions-contaminated soil, we observed high rates of destruction for RDX and TNT (98%) but not HMX. Our objective was to determine if HMX destruction by Fe(0) could be enhanced by increasing HMX solubility by physical (temperature) or chemical (surfactants) means. To determine electron acceptor preference, we treated RDX and HMX with Fe(0) in homogeneous solutions and binary mixtures. Increasing aqueous temperature (20 to 55 degrees C) increased HMX solubility (2 to 22 mg L(-1)) but did not increase destruction by Fe(0) in a contaminated soil slurry that also contained RDX and TNT. Batch experiments using equal molar concentrations of RDX and HMX demonstrated that RDX was preferentially reduced over HMX by Fe(0). By testing various surfactants, we found that the cationic surfactants (HDTMA [hexadecyltrimethylammonium bromide], didecyl, and didodecyl) were most effective in increasing HMX concentration in solution. Didecyl and HDTMA were also found to be highly effective in facilitating the transformation of HMX by Fe(0). Using HDTMA or didecyl solutions (3%, w/v) containing solid-phase HMX, we observed that 100% of the added HMX was transformed by Fe(0) in the didecyl matrix and 60% in the HDTMA matrix. These results indicate that cationic surfactants can increase HMX solubility and facilitate Fe(0)-mediated transformation kinetics but HMX destruction rates will be slowed when RDX is present.

Biodegradation of RDX and HMX Mixtures: Batch Screening Experiments and Sequencing Batch Reactors

Biodegradation is a potential treatment method for the high explosives RDX and HMX. In batch biodegradation tests, a facultative microbial consortium consumed the dissolved oxygen (DO) or reduced the oxidation-reduction potential (ORP) of the culture medium and biodegraded mixtures of RDX and HMX when supplied with various carbon and nitrogen sources. In batch tests with a mixture of carbon sources (glucose, glycerol, and succinic acid), RDX was reduced from 1.1 mg/L to below detectable levels within 4 days in the presence of 0.6 mg HMX/L. With ethanol as the carbon source, the culture degraded 90% of the initial 2.5 mg RDX/L over 8 days in the presence of 0.5 mg HMX/L. In batch mineralization tests, the culture converted 8 and 30% of the initial 14C-RDX to 14CO2 when supplied with ethanol and the mixed carbon sources, respectively. In both cases, a significant fraction of the initial 14C-RDX was converted to water-soluble 14C compounds, indicating triazine ring cleavage. However, mineralization was limit...

Approximate Method for Calculating the Impact Sensitivity Indices of Solid Explosive Mixtures

An approximate method is proposed to calculate the impact sensitivity indices (critical initiation pressure and critical charge thickness) for solid explosive mixtures (explosive compositions and mixtures of an oxidizer with a fuel). The calculation is based on some model concepts of the physicochemical and explosive properties of reactive mixtures. Test calculations of the sensitivity indices were performed for mixtures of HMX and TNT and mixtures of ammonium perchlorate with polymethylmethacrylate (PMMA) and TNT, and the results are compared with data of laboratory experiments on an impactor.