Minimizing Side Reactions Research Articles

An Effective Catholyte for Sulfide-Based All-Solid-State Batteries Utilizing Gas Absorbents.

All-solid-state batteries (ASSBs) possess the advantage of ensuring safety while simultaneously maximizing energy density, making them suitable for next-generation battery models. In particular, sulfide solid electrolytes (SSEs) are viewed as promising candidates for ASSB electrolytes due to their excellent ionic conductivity. However, a limitation exists in the form of interfacial side reactions occurring between the SSEs and cathode active materials (CAMs), as well as the generation of sulfide-based gases within the SSE. These issues lead to a reduction in the capacity of CAMs and an increase in internal resistance within the cell. To address these challenges, cathode composite materials incorporating zinc oxide (ZnO) are fabricated, effectively reducing various side reactions occurring in CAMs. Acting as a semiconductor, ZnO helps mitigate the rapid oxidation of the solid electrolyte facilitated by an electronic pathway, thereby minimizing side reactions, while maintaining electron pathways to the active material. Additionally, it absorbs sulfide-based gases, thus protecting the lithium ions within CAMs. In this study, the mass spectrometer is employed to observe gas generation phenomena within the ASSB cell. Furthermore, a clear elucidation of the side reactions occurring at the cathode and the causes of capacity reduction in ASSB are provided through density functional theory calculations.

Selective Activation of Peptide-Thioester Precursors for Templated Native Chemical Ligations.

Chemical protein synthesis enables access to proteins that would otherwise be difficult or impossible to obtain with traditional means such as recombinant expression. Chemoselective ligations provide the ability to join peptide segments prepared by solid-phase peptide synthesis. While native chemical ligation (NCL) is widely used, it is limited by the need for C-terminal thioesters with suitable reaction kinetics, properly placed native Cys or thiolated derivatives, and peptide segment solubility at low mM concentrations. Moreover, repetitive purifications to isolate ligated products are often yield-sapping, hampering efficiency and progress. In this work, we demonstrate the use of Controlled Activation of Peptides for Templated NCL (CAPTN). This traceless multi-segment templated NCL approach permits the one-pot synthesis of proteins by harnessing selective thioester activation and orthogonal conjugation chemistries to favor formation of the full-length ligated product while minimizing side reactions. Importantly, CAPTN provides kinetic enhancements allowing ligations at sterically hindered junctions and low peptide concentrations. Additionally, this one-pot approach removes the need for intermediate purification. We report the synthesis of two E. coli ribosomal subunits S16 and S17 enabled by the chemical tools described herein. We anticipate that CAPTN will expedite the synthesis of valuable proteins and expand on templated approaches for chemical protein synthesis.

Selective Activation of Peptide‐Thioester Precursors for Templated Native Chemical Ligations

AbstractChemical protein synthesis enables access to proteins that would otherwise be difficult or impossible to obtain with traditional means such as recombinant expression. Chemoselective ligations provide the ability to join peptide segments prepared by solid‐phase peptide synthesis. While native chemical ligation (NCL) is widely used, it is limited by the need for C‐terminal thioesters with suitable reaction kinetics, properly placed native Cys or thiolated derivatives, and peptide segment solubility at low mM concentrations. Moreover, repetitive purifications to isolate ligated products are often yield‐sapping, hampering efficiency and progress. In this work, we demonstrate the use of Controlled Activation of Peptides for Templated NCL (CAPTN). This traceless multi‐segment templated NCL approach permits the one‐pot synthesis of proteins by harnessing selective thioester activation and orthogonal conjugation chemistries to favor formation of the full‐length ligated product while minimizing side reactions. Importantly, CAPTN provides kinetic enhancements allowing ligations at sterically hindered junctions and low peptide concentrations. Additionally, this one‐pot approach removes the need for intermediate purification. We report the synthesis of two E. coli ribosomal subunits S16 and S17 enabled by the chemical tools described herein. We anticipate that CAPTN will expedite the synthesis of valuable proteins and expand on templated approaches for chemical protein synthesis.

Regulating Atomically-Precise Pt Sites for Boosting Light-Driven Dry Reforming of Methane.

Light-driven dry reforming of methane is a promising and mild route to convert two greenhouse gas into valuable syngas. However, developing facile strategy to atomically-precise regulate the active sites and realize balanced and stable syngas production is still challenging. Herein, we developed a spatial confinement approach to precisely control over platinum species on TiO2 surfaces, from single atoms to nanoclusters. The configuration comprising single atoms and sub-nanoclusters engenders pronounced electronic metal-support interactions, with resultant interfacial states prompting surface charge rearrangement. The unique geometric and electronic properties of these atom-cluster assemblies facilitate effective activation of CH4 and CO2, accelerating intermediate coupling and minimizing side reactions. Our catalyst exhibits an outstanding syngas generation rate of 34.41 mol gPt -1 h-1 with superior durability, displaying high apparent quantum yield of 9.1 % at 365 nm and turnover frequency of 1289 h-1. This work provides insightful understanding for exploring more multi-molecule systems at an atomic scale.

Regulating Atomically‐Precise Pt Sites for Boosting Light‐Driven Dry Reforming of Methane

AbstractLight‐driven dry reforming of methane is a promising and mild route to convert two greenhouse gas into valuable syngas. However, developing facile strategy to atomically‐precise regulate the active sites and realize balanced and stable syngas production is still challenging. Herein, we developed a spatial confinement approach to precisely control over platinum species on TiO2 surfaces, from single atoms to nanoclusters. The configuration comprising single atoms and sub‐nanoclusters engenders pronounced electronic metal‐support interactions, with resultant interfacial states prompting surface charge rearrangement. The unique geometric and electronic properties of these atom‐cluster assemblies facilitate effective activation of CH4 and CO2, accelerating intermediate coupling and minimizing side reactions. Our catalyst exhibits an outstanding syngas generation rate of 34.41 mol gPt−1 h−1 with superior durability, displaying high apparent quantum yield of 9.1 % at 365 nm and turnover frequency of 1289 h−1. This work provides insightful understanding for exploring more multi‐molecule systems at an atomic scale.

Photomediated Cationic Ring-Opening Polymerization of Cyclosiloxanes with Temporal Control.

Precision synthesis of polyorganosiloxanes and temporal control over the polymerization process during ring-opening polymerization (ROP) of cyclosiloxanes remain challenging due to the occurrence of side reactions, e.g., intramolecular transfer (backbiting) and intermolecular chain transfer, and irreversible catalyst transformation. In this study, a merocyanine-based photoacid catalyst is developed for cationic ROP of different cyclosiloxanes. A series of well-defined cyclotrisiloxane polymers with predetermined molar masses and low dispersities (Đ < 1.30) are successfully synthesized under various conditions (i.e., different catalyst loadings, initiator concentrations, solvents, and monomer types). Mechanistic insights by experiments and theoretical calculations suggest that the cationic active species, siloxonium ions, are combined with the catalyst anions to form tight ion pairs, thereby attenuating the reactivity of active species and subsequently minimizing side reactions. An efficient photocatalytic cycle is established among the catalyst, monomer, and polymer chain due to the rapid and reversible isomeric phototransformation of the catalyst, which endows the polymerization process with excellent temporal control. Successful in situ chain extension further confirms the controlled characteristics of photomediated CROP. This as-developed polymerization strategy effectively addresses long-standing challenges in the field of polyorganosiloxane synthesis.

Effect of Electrolyte Concentration on the Efficiency of Electrochemical Cells in India

Purpose: The aim of the study was to assess the effect of electrolyte concentration on the efficiency of electrochemical cells in India. Methodology: This study adopted a desk methodology. A desk study research design is commonly known as secondary data collection. This is basically collecting data from existing resources preferably because of its low cost advantage as compared to a field research. Our current study looked into already published studies and reports as the data was easily accessed through online journals and libraries. Findings: The study found that higher electrolyte concentrations generally enhance the conductivity of the cell, which improves the overall cell efficiency by facilitating the movement of ions between the electrodes. This results in a reduction in internal resistance, leading to a more efficient electrochemical reaction. Conversely, low electrolyte concentrations can hinder ion transport, increasing resistance and decreasing the efficiency of the cell. Additionally, optimal electrolyte concentration ensures a stable electrochemical environment, minimizing side reactions and enhancing the durability and performance of the cell. Therefore, maintaining an appropriate electrolyte concentration is crucial for maximizing the efficiency and longevity of electrochemical cells used in various applications, including energy storage and conversion technologies. Implications to Theory, practice and policy: Nernst equation, butler- Volmer equation and grotthuss mechanism may be used to anchor future studies on assessing the effect of electrolyte concentration on the efficiency of electrochemical cells in India. Based on empirical findings, manufacturers should focus on developing and commercializing electrolyte formulations that are optimized for specific cell types and applications. Policymakers should develop and enforce standards and guidelines for the optimal electrolyte concentrations in different types of electrochemical cells.

A Rechargeable “Rocking Chair” Type Zn−CO2 Battery

AbstractRising global temperatures and critical energy shortages have spurred researches into CO2 fixation and conversion within the realm of energy storage such as Zn−CO2 batteries. However, traditional Zn−CO2 batteries employ double‐compartment electrolytic cells with separate carriers for catholytes and anolytes, diverging from the “rocking chair” battery mechanism. The specific energy of these conventional batteries is constrained by the solubility of discharge reactants/products in the electrolyte. Additionally, H2O molecules tend to trigger parasitic reactions at the electrolyte/electrode interfaces, undermining the long‐term stability of Zn anodes. In this report, we introduce an innovative “rocking chair” type Zn−CO2 battery that utilizes a weak‐acidic zinc trifluoromethanesulfonate aqueous electrolyte compatible with both cathode and anode. This design minimizes side reactions on the Zn surface and leverages the high catalytic activity of the cathode material, allowing the battery to achieve a substantial discharge capacity of 6734 mAh g−1 and maintain performance over 65 cycles. Moreover, the successful production of pouch cells demonstrates the practical applicability of Zn−CO2 batteries. Electrode characterizations confirm superior electrochemical reversibility, facilitated by solid discharge products of ZnCO3 and C. This work advances a “rocking chair” Zn−CO2 battery with an enhanced specific energy and a reversible pathway, providing a foundation for developing high‐performance metal‐CO2 batteries.

A Rechargeable "Rocking Chair" Type Zn-CO2 Battery.

Rising global temperatures and critical energy shortages have spurred researches into CO2 fixation and conversion within the realm of energy storage such as Zn-CO2 batteries. However, traditional Zn-CO2 batteries employ double-compartment electrolytic cells with separate carriers for catholytes and anolytes, diverging from the "rocking chair" battery mechanism. The specific energy of these conventional batteries is constrained by the solubility of discharge reactants/products in the electrolyte. Additionally, H2O molecules tend to trigger parasitic reactions at the electrolyte/electrode interfaces, undermining the long-term stability of Zn anodes. In this report, we introduce an innovative "rocking chair" type Zn-CO2 battery that utilizes a weak-acidic zinc trifluoromethanesulfonate aqueous electrolyte compatible with both cathode and anode. This design minimizes side reactions on the Zn surface and leverages the high catalytic activity of the cathode material, allowing the battery to achieve a substantial discharge capacity of 6734 mAh g-1 and maintain performance over 65 cycles. Moreover, the successful production of pouch cells demonstrates the practical applicability of Zn-CO2 batteries. Electrode characterizations confirm superior electrochemical reversibility, facilitated by solid discharge products of ZnCO3 and C. This work advances a "rocking chair" Zn-CO2 battery with an enhanced specific energy and a reversible pathway, providing a foundation for developing high-performance metal-CO2 batteries.

Mixed conductive layer formed by ZnO–graphite conversion–reaction enables dendrite–free all–solid–state lithium metal batteries

Largescale application of sulfide solid electrolytes (SSEs) in nextgeneration allsolidstate Limetal batteries is currently limited by an unstable Li/SSEs interface and fast Lidendrite formation/growth during charging. This work has addressed these challenges by introducing ZnO and graphite composite to the surface of lithium metal, creating a multifunctional conductive composite layer with Ligraphite and LiZn alloy. This interfacial layer enhances Liion transport and minimizes side reactions at the Li/SSEs interface. As a result, the interfacial resistance of Li/SSEs decreased from 14.2 to 11.7 Ω cm², and the critical current density (CCD) significantly improved from 0.8 to 2.7 mA cm2. Moreover, the protective layer enables stable cycling of both Li/Li symmetric and LiNi0.8Mn0.1Co0.1O2/Li cells even at high current densities.

Activation of the Radical‐Mediated Pathway and Facilitation of the Li2S Conversion by N‐Doped Carbon‐Embedded Ti1–xCoxN Nanowires as a Multifunctional Separator with a High Donor‐Number Solvent toward Advanced Lithium–Sulfur Batteries

Electrolyte modification with a high donor‐number solvent is necessary to increase sulfur utilization, but it also presents poor compatibility with lithium metal. The amount of the solvent should be optimized to maximize sulfur utilization at the cathode and minimize side reactions with Li metal at the anode. An electrolyte solution comprising 1 vol% N,N‐dimethylacetamide (DMA) in a 1,2‐dimethoxyethane (DME)/1,3‐dioxolane (DOL) co‐solvent demonstrated increased discharge capacity and reduced overpotential compared to DME/DOL and DMA/DOL. In addition to electrolyte, modification that creates radical‐mediated pathways from a high donor‐number solvent, long‐cycle performance is achieved by effectively mitigating the shuttling effect and enhancing reaction kinetics with an efficient electrocatalyst. Cobalt doping into TiN introduced an upshift of the d‐band center with ferromagnetic properties that suppressed the shuttling effect, activated radical‐mediated pathways, and facilitated the Li2S conversion. A multifunctional separator fabricated with N‐doped carbon‐embedded cobalt‐doped titanium nitride nanowires (NC‐Ti0.95Co0.05N NWs) under 1 vol% DMA electrolyte achieved a discharge capacity of 464.4 mA h g−1 even after 200 cycles at a decay rate of 0.093% per cycle through the synergistic effects of electrolyte and electrocatalyst modifications. This work highlights the importance of ferromagnetic catalysts with a high donor‐number solvent for lithium–sulfur (Li–S) batteries.

Investigation of relationships between metabolic chemical reporter structures and S-glyco-modification effects

The approach of metabolic chemical reporters (MCRs) for labeling proteins has been widely used in the past several decades. Nevertheless, artificial side reaction generated with fully protected MCRs, termed S-glyco-modification, occurs with cysteine residues through base-promoted β-elimination and Michael addition, leading to false positives in the proteomic identification. Therefore, next generation of MCRs, including partially protected strategy and modifications on the backbone of monosaccharides, have emerged to improve the labeling efficiency. In this paper, we prepared fifteen kinds of unnatural monosaccharides to investigate the relationships of structures and S-glyco-modification labeling. Our results demonstrated that Ac4GlcNAz and Ac4GalNAz exhibited the most remarkable labeling effects among the detected compounds. Of note, Ac4ManNAz, Ac46AzGlucose and Ac46AzGalactose containing similar structures but did not show similar robust signals as them. Moreover, other modifications on the 1-, 2-, 3-, 4- and 6-site indicated minimal side reactions of S-glyco-modification, raising a possibility that subtle modifications of monosaccharide substrate may alter its role in the process of biosynthesis, for example, by change of electronegativity or enhancement of steric hindrance effects. In conclusion, our discoveries provide a new avenue to choose appropriate probe for selective label proteins in vitro and in vivo without undesired S-glyco-modification.

Antibody Drug Conjugates for Cancer Therapy: From Metallodrugs to Nature-Inspired Payloads.

This review highlights significant advancements in antibody-drug conjugates (ADCs) equipped with metal-based and nature-inspired payloads, focusing on synthetic strategies for antibody conjugation. Traditional methods such us maleimide and succinimide conjugation and classical condensation reactions are prevalent for metallodrugs and natural compounds. However, emerging non-conventional strategies such as photoconjugation are gaining traction due to their milder conditions and, in an aspect which minimizes side reactions, selective formation of ADC. The review also summarizes the therapeutic and diagnostic properties of these ADCs, highlighting their enhanced selectivity and reduced side effects in cancer treatment compared to non-conjugated payloads. ADCs combine the specificity of monoclonal antibodies with the cytotoxicity of chemotherapy drugs, offering a targeted approach to the elimination of cancer cells while sparing healthy tissues. This targeted mechanism has demonstrated impressive clinical efficacy in various malignancies. Key future advancements include improved linker technology for enhanced stability and controlled release of cytotoxic agents, incorporation of novel, more potent, cytotoxic agents, and the identification of new cancer-specific antigens through genomic and proteomic technologies. ADCs are also expected to play a crucial role in combination therapies with immune checkpoint inhibitors, CAR-T cells, and small molecule inhibitors, leading to more durable and potentially curative outcomes. Ongoing research and clinical trials are expanding their capabilities, paving the way for more effective, safer, and personalized treatments, positioning ADCs as a cornerstone of modern medicine and offering new hope to patients.

Imidazolium-Based Sulfonating Agent to Control the Degree of Sulfonation of Aromatic Polymers and Enable Plastics-to-Electronics Upgrading.

The accumulation of plastic waste in the environment is a growing environmental, economic, and societal challenge. Plastic upgrading, the conversion of low-value polymers to high-value materials, could address this challenge. Among upgrading strategies, the sulfonation of aromatic polymers is a powerful approach to access high-value materials for a range of applications, such as ion-exchange resins and membranes, electronic materials, and pharmaceuticals. While many sulfonation methods have been reported, achieving high degrees of sulfonation while minimizing side reactions that lead to defects in the polymer chains remains challenging. Additionally, sulfonating agents are most often used in large excess, which prevents precise control over the degree of sulfonation of aromatic polymers and their functionality. Herein, we address these challenges using 1,3-disulfonic acid imidazolium chloride ([Dsim]Cl), a sulfonic acid-based ionic liquid, to sulfonate aromatic polymers and upgrade plastic waste to electronic materials. We show that stoichiometric [Dsim]Cl can effectively sulfonate model polystyrene up to 92% in high yields, with minimal defects and high regioselectivity for the para position. Owing to its high reactivity, the use of substoichiometric [Dsim]Cl uniquely allows for precise control over the degree of sulfonation of polystyrene. This approach is also applicable to a wide range of aromatic polymers, including waste plastic. To prove the utility of our approach, samples of poly(styrene sulfonate) (PSS), obtained from either partially sulfonated polystyrene or expanded polystyrene waste, are used as scaffolds for poly(3,4-ethylenedioxythiophene) (PEDOT) to form the ubiquitous conductive material PEDOT:PSS. PEDOT:PSS from plastic waste is subsequently integrated into organic electrochemical transistors (OECTs) or as a hole transport layer (HTL) in a hybrid solar cell and shows the same performance as commercial PEDOT:PSS. This imidazolium-mediated approach to precisely sulfonating aromatic polymers provides a pathway toward upgrading postconsumer plastic waste to high-value electronic materials.

Highly efficient dual photoredox/copper catalyzed atom transfer radical polymerization achieved through mechanism-driven photocatalyst design

Atom transfer radical polymerization (ATRP) with dual photoredox/copper catalysis combines the advantages of photo-ATRP and photoredox-mediated ATRP, utilizing visible light and ensuring broad monomer scope and solvent compatibility while minimizing side reactions. Despite its popularity, challenges include high photocatalyst (PC) loadings (10 to 1000 ppm), requiring additional purification and increasing costs. In this study, we discover a PC that functions at the sub-ppm level for ATRP through mechanism-driven PC design. Through studying polymerization mechanisms, we find that the efficient polymerizations are driven by PCs whose ground state oxidation potential—responsible for PC regeneration—play a more important role than their excited state reducing power, responsible for initiation. This is verified by screening PCs with varying redox potentials and triplet excited state generation capabilities. Based on these findings, we identify a highly efficient PC, 4DCDP-IPN, featuring moderate excited state reducing power and a maximized ground state oxidation potential. Employing this PC at 50 ppb, we synthesize poly(methyl methacrylate) with high conversion, narrow molecular weight distribution, and high chain-end fidelity. This system exhibits oxygen tolerance and supports large-scale reactions under ambient conditions. Our findings, driven by the systematic PC design, offer meaningful insights for controlled radical polymerizations and metallaphotoredox-mediated syntheses beyond ATRP.

Engineered nickel phyllosilicate for selective 5-HMF C–O bond hydrogenation under benign conditions

The selective transformation of biomass-derived 5-hydroxymethylfurfural (5-HMF) into value-added chemicals is of significant interest to both academia and industry. In this study, we report on the direct hydrogenation of 5-HMF to 2,5-bis(hydroxymethyl)tetrahydrofuran (BHMTHF) instead of 2,5-dimethylfuran, achieving an impressive yield of 90.4% in 7 runs using a nickel phyllosilicate catalyst (Ni-PSL) under optimized conditions. The choice of solvent is crucial for minimizing side reactions, with tetrahydrofuran identified as an optimal solvent for reducing the formation of acetal by-products, which are typically promoted by protic organic solvents such as methanol or n-butanol. Pyridine–FTIR results reveal that the surface of Ni-PSL is enriched with Lewis acid sites, originating from coordinatively unsaturated Ni species, which are effectively generated through proper thermal treatment. Moreover, the total amount of acid sites in Ni-PSL can be modulated by adjusting the calcination temperature, without affecting the size of the Ni nanoparticles. These Lewis acid sites play pivotal roles in promoting the adsorption of the furan ring, thereby favoring the formation of BHMTHF under mild reaction conditions. However, an excess of Lewis acid sites promotes the cleavage of the C−OH bond, reducing the selectivity towards DMTHF.

Boosting interface compatibility of high-voltage LiNi0.5Mn1.5O4 cathode materials with an ionic-conductive Li0.33La0.56TiO3 coating

High voltage LiNi0.5Mn1.5O4 (LNMO) is a crucial cathode material for lithium-ion batteries (LIBs) aiming at high energy densities. However, its performance is hindered by the dissolution of transition metal ions and the instability of the cathode electrolyte interface (CEI) film at elevated voltages. To address these issues, we report a solvothermal method to prepare LNMO coated with Li+-conductor Li0.33La0.56TiO3 (LNMO@LLTO). Our study reveals that the LLTO coating not only enhances ion diffusion at the interface, minimizing the Li+ concentration gradient, and acts as a barrier against Mn-ion dissolution. This coating minimizes side reactions, mitigates structural degradation, and promotes the formation of a stable and balanced CEI film that incorporates LLTO, thus ensuring the long-term cycle stability. When compared to bulk LNMO, the LNMO@LLTO cathode demonstrates superior performance, maintaining reversible capacities of 111.4 and 102.2 mAh·g−1 after 500 cycles at 2 and 5C at 25 °C, respectively. Even at 60 °C, the LNMO@LLTO maintains a high capacity of 94.3 mAh·g−1 with minimal electrochemical polarization after 200 cycles at 2C. This simple preparation technique, together with its performance promotion, offers new insights into the development of high voltage cathode materials for high energy density LIBs.

Tuning of the acid sites in the zeolite-alumina composite Ni catalysts and their impact on the palm oil hydrodeoxygenation reaction

The hydrodeoxygenation (HDO) of bio-oil is one of the potential approaches to produce green diesel. However, HDO catalyst requires the development of bifunctionality which translates to the simultaneous presence of acidic and metal sites for desired catalytic activity and selectivity. Zeolites and their composites are attractive candidates for the conversion of biomass to fuels. In the present work, a series of Ni-incorporated Al2O3-zeolite beta bifunctional composite catalysts with distinct Al2O3 (25–75 wt%) and Ni contents (5–15 wt%) were synthesized via a facile one-pot method directly from nickel acetate, nano-boehmite (γ-AlO(OH)) and the NH4+ form of beta zeolite (NH4+-BZ). The nano-boehmite particles, due to the positive charges on their surface, electrostatically attract negatively charged beta zeolite crystals, which leads to the assembly of a hierarchical pore structure upon calcination. Interestingly, the composite catalysts synthesized were quite homogeneous with uniform dispersion of Ni particles. All composite catalysts were thoroughly characterized using XRD, SEM-EDX, SEM-mapping, HR-TEM, H2-TPR, H2-TPD, NH3-TPD, XPS, 31P MAS NMR, 27Al MAS NMR and N2 sorption analysis. The synthesized composite catalysts with distinct Al2O3 contents showed diverse textural properties, distinct nature of acid sites and improved performance in hydrodeoxygenation of palm oil. Particularly, the Ni/BZ-Al50 (with BZ:Al2O3 = 50:50) composite catalyst significantly enhanced the conversion of palm oil (up to 90%) and yield of n-C15-C18 hydrocarbons (up to 69%) at moderate temperature of 375 °C as compared to 10Ni/BZ catalyst (Conv. = 75%, yield of n-C15-C18 = 52%). The higher catalytic performance realized with composite catalysts can be ascribed to its hierarchical pore structure, moderate acidity (chemisorption studies), tuned acid sites nature (solid state NMR) and homogeneous distribution of active Ni sites (H2 chemisorption) which helps to improve product selectivity by minimizing side reactions. The time-on-stream (TOS) experiments were carried out up to 20 h which clearly showed that composite catalysts are more stable suggesting the lower amount of coke deposition (TPO studies) and suppression of metal sintering.

Diastereoselective Hydrogenation of Tetrasubstituted Olefins using a Heterogeneous Pt-Ni Alloy Catalyst.

Stereoselective hydrogenation of tetrasubstituted olefins is an attractive method to access compounds with two contiguous stereocenters. However, homogeneous catalysts for enantio- and diastereoselective hydrogenation exhibit low reactivity toward tetrasubstituted olefins due to steric crowding between the ligand scaffold and the substrate. Monometallic heterogeneous catalysts, on the other hand, provide accessible surface active sites for hindered olefins but exhibit unpredictable and inconsistent stereoinduction. In this work, we develop a Pt-Ni bimetallic alloy catalyst that can diastereoselectively hydrogenate unactivated, sterically-bulky tetrasubstituted olefins, utilizing the more oxophilic Ni atoms to adsorb a hydroxyl directing group and direct facially-selective hydrogen addition to the olefin via the Pt atoms. Structure-activity studies on several Pt-Ni compositions underscore the importance of exposing a uniform PtNi alloy surface to achieve high diastereoselectivity and minimize side reactions. The optimized Pt-Ni/SiO2 catalyst exhibits good functional group tolerance and broad scope for tetrasubstituted olefins in a cyclopentene scaffold, generating cyclopentanol products with three contiguous stereocenters. The synthetic utility of the method is demonstrated in a four-step synthesis of (1R,2S)-(+)-cis-methyldihydrojasmonate with high yield and enantiopurity.

Hydrodeoxygenation of lignin-derived compounds for alkane fuels using bifunctional Co/HZ-HT

The selective hydrodeoxygenation of lignin-derived compounds is an effective pathway for producing liquid fuels. Here, a series of Co-based catalysts were prepared for converting lignin-derived phenols into alkane fuels. The effects of cobalt loading, Si/Al ratio, reaction temperature, time, and pressure on the distributions of alkane fuels were systematically investigated. The experimental results demonstrated that the in-situ grown LDH structure in Co/HZ-HT significantly improved the pore structure of the catalyst, not only enhancing the dispersion of the metallic particles and overall stability but also strengthening the interaction between the metal and the support. The complete conversion of guaiacol was achieved, and the selectivity of cyclohexane reached 97.5% under the conditions of 200 °C, 2 h, 3 MPa H2, and Si/Al ratio of 25. Co/HZ-HT exhibits excellent hydrogenolysis performance and wide applicability, outperforming Co/HZ catalysts prepared using conventional impregnation methods. By extending the feedstock to lignin-derived compounds, the complete deoxygenation of the components and hydrogenation of the aromatic rings were both realized with minimal side reactions.