MIMO Antenna Research Articles

A detailed review of 5G MIMO and array antenna design evolution with performance enhancement for mmWave applications

A detailed review of 5G MIMO and array antenna design evolution with performance enhancement for mmWave applications

A corrugated edge tapered slot dual polarized MIMO antenna for phased array systems

A corrugated edge tapered slot dual polarized MIMO antenna for phased array systems

Design and characterization of a circular ring monopole antenna and its MIMO configuration for sub-6 GHz, sub-7 GHz and mm-wave 5G applications

Abstract In this paper, a circular ring monopole antenna, along with its MIMO configuration for sub-6 GHz, sub-7 GHz and mm-wave 5G applications is presented. The single element spans a wide range of frequencies in the sub-6 GHz and mm-wave regions, including a triple-band covering 1.9–6 GHz, 23.3–33.5 GHz, and a super-wide band starting from 37.5 GHz. A two-element MIMO antenna, derived from the single element, has been developed to operate in both frequency regions. It meets the -10 dB criterion with a bandwidth of 4.8 GHz (3.2 to 7.3 GHz) in the sub-6 GHz/sub-7 GHz spectrum. Additionally, the antenna exhibits a super-wide band in the mm-wave region starting at 30.4 GHz. The design covers key bands such as n78, LTE band 46, n96, 39 GHz band, 41 GHz band and more, assigned for 5G sub-6 GHz, sub-7 GHz and mm-wave applications. Improved isolation from 12 dB to 18.5 dB is achieved through a simple decoupling line structure between elements. The proposed MIMO antenna (75 × 56.4 × 1.52 mm³) exhibits a peak gain of 9.8 dBi, high isolation (18.5 dB), low envelope correlation coefficient (ECC <0.016 ), high diversity gain (DG > 9.995), and efficiency (< 97%).

A defected substrate 4-element mimo antenna with higher diversity characteristics for 5G sub 6 GHz N77/N78 band applications

A defected substrate 4-element mimo antenna with higher diversity characteristics for 5G sub 6 GHz N77/N78 band applications

Meander Line Loaded 2- Port Stepped Impedance Feed Slotted MIMO Antenna For C and Lower X-Band Communication

Meander Line Loaded 2- Port Stepped Impedance Feed Slotted MIMO Antenna For C and Lower X-Band Communication

A wideband circularly polarized four port microstrip MIMO antenna with high gain and enhanced isolation for 5G millimeter frequency applications

Abstract In this article, a MIMO antenna system featuring wide bandwidth, high gain, and circular polarization for 5G communication networks is presented. The proposed antenna enables high data rates, enhanced signal reliability, and improved performance in dynamic and challenging 5G environments. Wide bandwidth ensures compatibility with various 5G frequency bands, while circular polarization allows for better signal propagation and reception, particularly in non-line-of-sight scenarios. In that regard, the present endeavor exhibits an enhanced bandwidth 4-port circularly polarized MIMO antenna to encounter polarization mismatch along with high data rates. The presented MIMO antenna comprises four identical patches strategically positioned in orthogonal orientations in such a way as to provide the circular polarization direction. Meanwhile, the bandwidth is extended by inserting straightforward defected ground structure (DGS) and L slots. The MIMO antenna anticipated in this work offers an impedance bandwidth covering from 24 GHz to 28.5 GHz and an axial ratio bandwidth of 62% within the overall band. It demonstrates excellent performance with a high peak gain of approximately 14.84 dB. Additionally, it exhibits strong isolation of more than 20dB among the closely packed antennas, ensuring reliable communication and minimizing interference. The combination of these features in a MIMO antenna system is crucial for meeting the demanding requirements of 5G communication, including increased data capacity, low latency, and reliable connectivity. The simulated and measured outcomes exhibit robust concurrence, signifying a high level of accuracy. Consequently, the suggested MIMO antenna appears well-suited for encompassing the 5G bands designated for deployment in the USA (27.50–28.35 GHz) and Europe (24.25 - 27.5 GHz).

Eight-port multiband MIMO antenna design with high isolation for 5G smartphones

Eight-port multiband MIMO antenna design with high isolation for 5G smartphones

Compact size and wideband 4 × 4 MIMO antenna for 5G NR networks

Abstract In this paper, a crescent-shaped four-port MIMO is proposed to deploy in 5 G wireless network coverage with the advantages of wide bandwidth. The MIMO antenna is printed on an RO4003 substrate (ε r = 3.55) with a thickness of 0.203 mm and a rectangular slot in the ground plane to obtain the desired performance. The antenna is duplicated two times in an orthogonal arrangement to achieve 4 ports MIMO antenna for capacity improvement purposes. The antenna satisfies an impedance bandwidth of 20 GHz (20.5–40.5 GHz) with an isolation of ≥22 dB. Furthermore, the suggested 4-port MIMO antenna is fabricated and tested to validate the simulated outcomes, and good consistency between results is achieved in terms of scattering parameters, radiation patterns, gain, and diversity parameters. The presented 4-port MIMO antenna is considered a good candidate for future 5 G NR networks due to its competitive advantages.

Dual-Wide Multi-Band (DWMB) four-port flexible MIMO antenna for on-body multiple wireless applications including high diversity performance.

The single-input-single-output technology experiences loss of data in the communication channel due to the receiving antenna undergoing fading of the signal impinged on it. Today's need is faster data transfer with multiple applications in the single antenna with multiple-identical radiating elements, leading to multiple-input-multiple-outputDWMB (MIMODWMB) technology. The MIMODWMB configuration with multi-band capability is the objective of the proposed work with applications ranging between microwave-millimeterWave bands. The four-port Dual-Wide Multi-Band (DWMB) MIMODWMB antenna radiating electro-magnetic-energy is proposed, which generates measured bandwidths of 7.27GHz-34.32GHz (Band 1) and 46.54GHz-71.52GHz (Band 2) including applications Up-link/Down-link Satellite System, X-Band, Ku-Band, ISM 24.0GHz (24.0GHz-24.25GHz), 24.0GHz UWB Band (21.65GHz-26.65GHz), n258, n257/n261 and n263 V-band. The proposed antenna technology is printed on Rogers's low permittivity substrate with a hexagon patch etched with dual merged-elliptical slot and three identical circular slots to achieve high impedance matching for Band 1. The partial-ground is etched by a rectangular slot for better impedance matching, and two-thin-etched rectangular slits generate 60.0GHz Band 2. The thin substrate, thickness 0.254mm, is utilized for flexible applications without compromising the operation of dual wide bandwidths. The flexible antenna is also subjected to analysis of Specific-Absorption-Rate (SAR) analysis at key frequencies within both the bands and found to be within the standard limit of 1.60W/Kg for 1g of the human tissue model and corresponds to 1.01W/Kg at 10.0GHz, 0.280W/Kg at 15.0GHz, 0.475W/Kg at 26.0GHz, 0.588W/Kg at 28.0GHz & 0.301W/Kg at 60.0GHz. The high diversity performance with Envelope Correlation Coefficient<0.50, Diversity Gain≈10.0dB, Total Active Reflection Coefficent<0dB, Channel Capacity Loss<0.40b/s/Hz and multi-band capability for mobile users make the proposed work suitable for flexible on-body applications in a wireless environment. The proposed work MIMODWMB antenna offers advantages such as reduced size (20mm×24mm: 0.61λ0×0.74λ0 at λ0 = 7.27GHz) and a wide range of impedance bandwidths, which are useful for several applications. Also, due to the flexible nature of the design, they can be used for future on-body wearable applications.

Wearable and ultra-compact mm-wave four port MIMO antenna for dual band n261 and n260 (28/38) GHz 5G applications

Wearable and ultra-compact mm-wave four port MIMO antenna for dual band n261 and n260 (28/38) GHz 5G applications

Dual-circular slotted low-profile ultrawideband textile MIMO antenna with ground slot stub for Sub-6G, ISM, and IoT applications

Dual-circular slotted low-profile ultrawideband textile MIMO antenna with ground slot stub for Sub-6G, ISM, and IoT applications

Cost-effective circularly polarized MIMO antenna for Wi-Fi applications

Cost-effective circularly polarized MIMO antenna for Wi-Fi applications

Dual band four port MIMO antenna with dual circular polarization for Wi-Fi/WiMAX applications

The planar compact four port circularly polarized printed MIMO antenna described in this article is small and intended to support Wi-Fi and WiMAX applications. Suggested four E-shaped monopole elements make up the dual circularly polarized (CP) MIMO antenna that has two left hand CP (LHCP) elements and two right hand CP (RHCP) elements. An I shaped strip is used to join separate ground planes of designed E shaped monopole antenna to have same voltage levels. A good diversity performance is achieved with an envelope correlation coefficient (ECC) of less than 0.15. The 60 mm × 60 mm antenna is designed from FR4 material, which is inexpensive and has a 1.6 mm thickness. Using a high-frequency structure simulator (HFSS), the suggested MIMO antenna is designed and optimized. The measured findings demonstrate the circular polarization, 3-dB axial ratio beamwidth, impedance bandwidth of 2.11 GHz −2.42 GHz and 3.40 GHz-3.51 GHz, adequate axial ratio bandwidth (ARBW) of the suggested MIMO antenna along with high isolation of −17 dB, gain of 3.43 and 2.09 dBic at 2.4 GHz and 3.5 GHz respectively, TARC (Total active reflection coefficient) of less than 0 dB, a CCL (Channel capacity loss) of lesser than 0.4 bits/sec/Hz, and an MEG (Mean effective gain) value of less than 3 dB.

CPW fed optically transparent ultrawideband fractal MIMO terahertz antenna with meshed ground plane

Abstract An optically transparent UWB antenna element and its two-element pattern diversity MIMO configurations are presented in this paper. Three iterations of the quarter elliptical coplanar waveguide ground plane, rectangular microstrip feedline, and octagonal annular rings make up the antenna element. By metal meshing the ground planes and loading the radiator with several octagonal slots, the optical transparency is improved. It has a maximal achieved gain of 6.78 dBi and operates with steady radiation characteristics over the frequency spectrum of 4.52–28.64 THz (145.48%). The dimensions of the antenna element are 18 × 20.5 μm2. A metallic stub is positioned between two identical antenna components that are positioned orthogonally to one another to create a two-element pattern diversity MIMO antenna arrangement. The MIMO antenna is 20.5 × 42.5 μm2 in total. Its impedance bandwidth is 23.72 THz for port 2 and 22.68 THz for port 1. Using a rectangular stub results in an intraport isolation of &gt;19 dB. Between the two ports, the planes in the radiation patterns have switched places. The diversity performance characteristics, which are considerably below the permissible limitations, are as follows: ECC &gt; 0.01, CCL &lt; 0.3 b/s/Hz, DG ∼ 10, TARC &lt; 0 dB, MEG ∼ −3 dB, and 1≤VSWR_MIMO≤2. Compared to previously published structures, the suggested antenna structures have the advantages of smaller dimensions, a larger bandwidth, and improved optical transparency.

Isolation improvement between two tightly coupled QMSIW MIMO antenna elements using spoof surface plasmon polariton structure

AbstractA spoof surface plasmon polariton superstrate structure‐based decoupling method is proposed in this paper to reduce mutual coupling between two tightly coupled quarter‐mode substrate integrated waveguide antenna elements. This superstrate is a periodic structure suspended over the antenna elements with an inter‐element spacing of 0.02 λ0 (1 mm) at 6 GHz. It has been demonstrated that the isolation can be improved from 6.5 dB to more than 39 dB within the operation band in measurement. Further, it has been shown that the proposed method can improve both the total efficiency (by 25%) and gain (1.4 dBi) of the multiple‐input multiple‐output antenna.

Hybrid Optimization Framework for MIMO Antenna Design in Wearable IoT Applications Using Deep Learning and Bayesian Method

Hybrid Optimization Framework for MIMO Antenna Design in Wearable IoT Applications Using Deep Learning and Bayesian Method

Effective area reduction &amp; surface waves suppression of a novel four-element MIMO antenna exclusively designed for dual band 5G sub 6 GHz (N77/N78 &amp; N79) applications

Effective area reduction &amp; surface waves suppression of a novel four-element MIMO antenna exclusively designed for dual band 5G sub 6 GHz (N77/N78 &amp; N79) applications

Thirty two port super wideband diversity antenna for indoor communications

This paper introduces a novel design featuring a thirty-two port diversity antenna with an elliptical shape, fed by an asymmetric coplanar waveguide (CPW). The antenna incorporates uneven meander lines, tailored for super-wideband (SWB) applications. The structure of the unit cell is of an elliptical patch with an elliptical slot, and it is connected to a rectangular stub and asymmetric meander line. The size of the single element is 22 mm × 20 mm, and it operates from 3 to 40 GHz. The bandwidth dimension ratio of the unit cell is 3911, bandwidth ratio is 13.33:1, and fractional bandwidth is 172.09%. The single element is developed into a 3-D thirty-two port diverse antenna, composed of a horizontal plane and four planes perpendicular to it. The diverse antenna has a peak gain of 12.5 dBi and an efficiency of 94%. The computed envelope correlation coefficient (ECC), as determined using S-parameters and far-field measurements, is less than 0.1. The attained diversity gains (DGs) of the developed MIMO antenna are above 9.9 dB in terms of both S-parameter and far-field computations. The obtained thirty-two port diverse antenna channel capacity loss (CCL) is below 0.25 bits/s/Hz. The mean effective gain (MEG) of the constructed thirty-two port antenna is below 2. To validate the appropriateness of the developed thirty-two port antenna for wireless indoor environment, an enclosure made of acrylonitrile butadiene styrene (ABS) is crafted and fabricated, and the characteristics of the proposed diverse antenna are investigated.

Evaluating the performance measurement of novel octangular star shaped micromachined substrate with self-isolated 8 × 8 port MIMO antenna for dual band 28 GHz (n261) and 39 GHz (n260) millimeter-wave 5G applications

Evaluating the performance measurement of novel octangular star shaped micromachined substrate with self-isolated 8 × 8 port MIMO antenna for dual band 28 GHz (n261) and 39 GHz (n260) millimeter-wave 5G applications

Compact high isolation MIMO antenna array for 6G application (0.1–10 THZ)

ABSTRACT In wireless communication, channel capacity and reliability can be increased using a Multiple Input Multiple Output antenna. For several future applications, the sixth generation terahertz frequency spectrum (0.1–10 THz) will be used to increase the communication speed in wireless networks. To minimise coupling and reconfiguration, the decoupling structure and pin diodes are used in the MIMO antenna. This research presents a four-port electromagnetic band gap-based MIMO antenna array for 6 G applications. The entire MIMO system is influenced by the electromagnetic coupling between the four or eight MIMO parts. In the ground plane, antenna size reduction, insulation improvement, and defective ground are used. Here, the antenna is designed and compared using the two substrates Flame Retardant and polyimide. The performance of the suggested design is 288 GHz Polyimide and 301.6 GHz FR4. The suggested design showed better performance of the antenna as well as diversity measures.