Middle Ring Research Articles

Analysis of shield tunnel response to bilateral pit excavation with a focus on perimeter pressure and deformation mechanisms

This study aims to investigate the responses of shield tunnel structures subjected to disturbances caused by bilateral pit excavation, and it systematically reveals for the first time the impact mechanism of bilateral pit excavation on the distribution of perimeter pressure and deformation patterns of shield tunnels. Using a bilateral pit excavation project in Nanjing as a case study, this research establishes methods for calculating longitudinal displacement and circumferential pressure of tunnels under bilateral pit excavation conditions, employing the image source method for analysis. A refined three-ring segment model is developed, and the load structure method is used to analyze the impact of deep foundation excavation on the tunnel located between the two excavation sites. The results indicate that, compared to unilateral excavation, bilateral excavation significantly increases the perimeter pressure at the top and bottom of the tunnel, with a smaller increase in pressure at the arch waist. The deformation pattern is characterized by contraction at the top and bottom and expansion at the waist, forming a transverse elliptical deformation. The maximum vertical convergence values of the middle segment ring are 25.00 mm at the top and 25.88 mm at the bottom, with a vertical absolute convergence value of 44.5 mm and a convergence ratio (ΔDt/Dt) of 0.72%. As the foundation coefficient increases, the perimeter pressure at the top and bottom of the tunnel also increases. When the tunnel is closer to the foundation pits (Sp decreases), the perimeter pressure at the bottom of the tunnel increases. Conversely, as the distance between the two foundation pits (S) increases, the impact of excavation on the tunnel shifts from the upper part to the lower part, resulting in decreased upper perimeter pressure and increased lower perimeter pressure. The research findings provide important references for similar engineering projects.

The Normal Active Range of Motion of the Index, Middle, Ring, and Little Fingers in a Sample of Indian Population.

Background The normative data for finger range of motion (ROM) are not available for the Indian population. The aim of our study was to measure the active ROM of finger joints in normal healthy volunteers in a sample of Indian population. Materials and Methods This is a prospective observational study conducted as a part of the Indian normative data project of the Indian Society for Surgery of the Hand (ISSH). The study included one participating center from four geographical regions of the country. Certified goniometers were used to measure the ROM of fingers in all centers. A standardized methodology was devised. A pilot study was done to assess the interobserver and intraobserver reliability, following which data were collected by one measurement. Results This pilot study was performed in 20 hands that showed good interobserver and intraobserver reliability correlation. A total of 390 hands were measured in four participating centers. Active flexion of metacarpophalangeal (MCP) joint was the highest in the middle finger (86.6 ± 10.4 degrees) followed by the index finger (86.0 ± 9.2 degrees), little finger (85.0 ± 8.4 degrees), and ring finger (84.2 ± 8.6 degrees). The index finger (97.2 ± 16.9 degrees) showed maximum proximal interphalangeal (PIP) joint flexion followed by the middle finger (96.2 ± 15.8 degrees), ring finger (96.0 ± 15.9 degrees), and little finger (91.8 ± 12.7 degrees). Distal interphalangeal (DIP) joint flexion increased from the index finger (81.6 ± 13.9 degrees) to the little finger (84.6 ± 12.9 degrees). The little finger MCP joint (26.3 ± 6.2 degrees) showed maximum extension followed by the index finger (25.7 ± 6.8 degrees), middle finger (24.7 ± 6.7 degrees) and ring finger (22.3 ± 7.1 degrees). The middle finger (15.6 ± 8.1 degrees) and ring finger (16.2 ± 8 degrees) had more PIP joint extension when compared to the index (13.7 ± 7.8 degrees) and little finger (13.2 ± 8.4 degrees). The ring finger (8.1 ± 6.8 degrees) and the middle finger (8.4 ± 6.9 degrees) had more DIP joint extension when compared with the index finger (6.0 ± 6.0 degrees) and the little finger (6.8 ± 6.7 degrees). Total active motion (TAM) of the middle finger (315.9 ± 31.0 degrees) was the maximum followed by the index finger (310.2 ± 27.3 degrees), ring finger (308.8 ± 29.1 degrees), and little finger (307.8 ± 25.2 degrees). Gender, body mass index (BMI), mother tongue, geographical location, and occupation were factors that had significant correlation, while no significant differences based on side, hand dominance, and age were noted. Conclusion We have reported normative data of finger ROM and TAM for the index, middle, ring, and little fingers in the Indian population. Finger ROM in the Indian population is highly variable. The observed TAM in the Indian population is higher than what is reported earlier.

Role of interaction mode of phenanthrene derivatives as selective PDE5 inhibitors using molecular dynamics simulations and quantum chemical calculations.

Phosphodiesterase type 5 (PDE5) inhibitors play a crucial role in blocking PDE5 to improve erectile dysfunction (ED). However, most PDE5 drugs revealed side effects including the loss of vision due to the PDE6 inhibition. Phenanthrene derivatives isolated from E. macrobulbon were previously reported as PDE5 inhibitors. Two phenanthrene derivatives (cpds 1-2) revealed better inhibition to PDE5 than PDE6 and cpd 1 is more selective to PDE5 than cpd 2. To elucidate why the phenanthrene derivatives could inhibit PDE5 and PDE6, their binding modes were investigated using molecular dynamics simulations and quantum chemical calculations, as compared to the PDE5 drugs. From the results, all four drugs and phenanthrene derivatives revealed similar π-π interactions to Phe820 in PDE5. Additional H-bond interaction to Gln817 in PDE5 resulted in better PDE5 inhibition of vardenafil and tadalafil. Moreover, cpds 1-2 were able to form the H-bond interaction with Asp764 in PDE5. In the case of the PDE6, the loss of π-π interaction to Phe776 and H-bond interaction to Gln773 indicated the important points for losing the PDE6 inhibition. In conclusion, to develop the new potent PDE5 inhibitors, not only the important interaction with PDE5 but also the interaction with PDE6 should be considered. In phenanthrene derivatives, the middle ring was significant to form π-π interactions to Phe820 in PDE5 and hydroxyl substituent was also the key part to form the H-bond interaction with Asp764 in PDE5. Principal component analysis (PCA) and free energy landscape (FEL) analysis indicated the stability of the system. The bioavailability, drug-likeness, and pharmacokinetics of phenanthrene derivatives were also predicted. These derivatives revealed good drug-likeness and GI absorption. The obtained results showed that phenanthrene derivatives could be interesting for the development of PDE5 inhibitors in the future.

Case studies of the load-bearing performance of shield tunnel segment with misaligned defects

The segment misalignment is a common defect in the segment installation of a shield tunnel construction, due to the complexity and uncertainty of its construction conditions. This raises a concerning about the safety of the segment lining for the shield tunnel. In this paper, the integrated numerical models with surrounding rock, peastone grouting and segment lining were built using three-dimensional finite element method, by introducing two kinds of misaligned defects of segments. One was the misalignment that elongated the horizontal axis of the transversal ring section of segment lining, another was the misalignment between adjacent rings of segments. To eliminate the impact of boundary on numerical results, seven rings of segments are built for the three-dimensional finite element models, and the middle ring is dealt with for the results analysis under V-class surrounding rock, including the circumferential stress of outer and inner layers of the segment, the contact stress on joint surface between segments, and the stress of locating pins between adjacent rings. Results indicate that the two kinds of misaligned defects create pronounced impact on tensile stress of segment at the bottom and the crown segments, respectively, which produces a greater tensile stress to increase cracking risk even abrupt fracture of segment. However, the misaligned defects have a slight impact on the contact stress and the locating pins stress. Therefore, attention should be paid to the cracking of bottom or crown segments in the segment lining of shield tunnel.

Is the availability and quality of local early childhood education and care services associated with young children's mental health at school entry?

PurposeThis study investigated the relationship between geographic availability (and quality) of local early childhood education and care services and children's early mental health outcomes for all children entering their first year of full-time school in Melbourne, Australia. MethodsWe capitalise on a unique population linked dataset, the Australian Early Development Census – Built Environment, which combines geospatial measures of children's neighbourhoods with demographic information and child mental health outcomes for all school entrants in Australia's 21 most populous cities and towns. Objective early childhood education and care service location and quality exposures were developed for each study child based on home addresses. Four geographic availability exposures (counts within 3 km) were examined for cross-sectional associations with child mental health outcomes (externalising and internalising difficulties, competence). We estimated associations using multilevel logistic regression (Markov Chain Monte Carlo estimation) adjusting for child demographics and stratifying by urbanicity. ResultsChildren with higher counts of high-quality preschool services within 3 km of home had lower odds of difficulties and higher odds of competence. Overall, exposures were most consistently associated with children's competence. Across all outcomes, the most consistent patterning was observed for children living in the inner city and middle ring. Results varied depending on whether service quality was accounted for in measures of availability. Geographic availability of early childhood services showed patterning by neighbourhood disadvantage and by maternal education. ConclusionWe found some evidence that geographic availability of high-quality preschools was associated with better child mental health outcomes, but results varied by urbanicity. While future research is required to unpack these differences, these findings indicate the importance of accounting for both geographic availability and service quality simultaneously in future research, policy and practice.

Efficient wideband tunable radio frequency-optical conversion via triply resonant photonic molecules.

Electro-optic (EO) transduction of weak radio frequency (RF) and millimeter-wave signals, such as those received by an antenna, onto laser sidebands for processing in the optical domain requires efficient EO modulators. Microrings offer spatial density and efficiency advantages over Mach-Zehnder modulators (MZMs), but conventional single-ring modulators suffer a fundamental trade-off between resonantly enhanced conversion efficiency and the RF carrier frequency that it can accommodate. Dual-cavity "photonic molecule" modulators resolve this trade-off, allowing high efficiency independent of the RF carrier frequency by providing separate resonant supermodes to enhance the laser local oscillator (LO) and the narrowband RF-detuned sideband. However, the RF frequency is fixed at design time by geometry, with efficiency dropping quickly for RF carriers away from the design value. We propose a novel, to the best of our knowledge, triple-cavity configuration with an off-resonant middle ring acting as an effective tunable coupler between two active modulator cavities. This configuration provides wideband tunability of the target RF carrier while maintaining efficient sideband conversion. When the middle ring is passive (high Q), this configuration provides wide RF tunability with no efficiency penalty over the fixed dual-cavity case and could become an important building block for future RF/mm-wave photonic integrated circuits (PICs).

Influence of Ga doped CoMo/Al2O3 catalysts on the selective hydrogenation performance of polycyclic aromatic hydrocarbons

It is a challenge to effectively control the intermediate ring hydrogenation products in tricyclic aromatic hydrocracking reactions in order to further increase the selectivity of BTX. A series of doped gallium modified CoMo/Al2O3 catalysts were prepared, the effect of gallium on the catalyst's physicochemical properties, active phase structure and hydrogenation reaction pathway was studied. The study revealed that the doping of gallium species promoted the sulfidation of Mo species and improved the catalytic activity of the catalyst. The 1 % Ga-modified catalyst showed the best selective hydrogenation performance, in which the conversion rate of phenanthrene was up to 83.75 % and the selectivity for dihydrophenanthrene reached 28.60 %. In addition, DFT calculations show that the introduction of Ga into the active phase between the Co and Mo atoms results in a higher differential charge density in the middle ring, which is more conducive to hydrogen adsorption.

Discovery of an EP300 Inhibitor using Structure-based Virtual Screening and Bioactivity Evaluation.

EP300 (E1A binding protein p300) played a significant role in serial diseases such as cancer, neurodegenerative disease. Therefore, it became a significant target. Targeting EP300 discovery of a novel drug to alleviate these diseases. In this paper, 17 candidate compounds were obtained using a structure-based virtual screening approach, 4449-0460, with an IC50 of 5.89 ± 2.08 uM, which was identified by the EP300 bioactivity test. 4449-0460 consisted of three rings. The middle benzene ring connected the 5-ethylideneimidazolidine-2,4-dione group and the 3-F-Phenylmethoxy group. Furthermore, the interaction mechanism between 4449-0460 and EP300 was explored by combining molecular dynamics (MD) simulations and binding free energy calculation methods. The binding free energy of EP300 with 4449-0460 was -10.93 kcal/mol, and mainly came from the nonpolar energy term (ΔGnonpolar). Pro1074, Phe1075, Val1079, Leu1084, and Val1138 were the key residues in EP300/4449-0460 binding with more -1 kcal/mol energy contribution. 4449-0460 was a promising inhibitor targeting EP300, which had implications for the development of drugs for EP300-related diseases.

A broadband single‐layer reflectarray antenna with split ring element

AbstractA broadband single‐layer reflectarray comprising three‐layer concentric split ring elements is proposed. The reflection phase is achieved by changing the flare angle of the inner and outer split rings. The resonance of the element is easily controlled by varying the relative relationships between the homomorphic patches. And the length of the split ring changes in the azimuth direction, which improves the utilization rate of unit space. The middle split ring acts as a parasitic structure with constant size, making the surface current distribution of the element more uniform to improve the element bandwidth. A reflectarray containing 256 elements is designed and tested. The measured results indicate that the peak gain is 25.3 dBi corresponding to the aperture efficiency of 42%. And the 1‐dB gain bandwidth of the reflectarray of 21.7% is achieved.

Investigation on axial compression performance of self-compacting fly ash concrete filled square steel tube column: Tests and numerical simulation

Self-compacting concrete has the advantages of high fluidity, high uniform density, and low porosity. To promote the engineering application of self-compacting concrete, this article studies the axial compression test of ten square steel tube self-compacting concrete columns. The effects of design parameters such as different grades of concrete strength and internal structures of circular steel tubes, square steel tubes, and H-shaped steel on the mechanical properties of self-compacting fly ash concrete filled square steel tube columns are studied. The failure mode, characteristic load and characteristic displacement, ductility, and energy dissipation capacity of each specimen are analyzed. On the basis of the test, the finite element analysis model of steel tube self-compacting concrete column is established, and the test results and simulation results are compared and analyzed. The results show that: the failure mode of the square steel tube specimen is the multilayer middle and upper ring buckling failure. Internal structural measures of square steel tube and H-shaped steel can improve the bearing capacity, ductility, and energy dissipation capacity of the specimen. It is not recommended to use the specimen with an outer square and an inner circle design. The results of the finite element simulation have a high degree of matching with the test results, which intuitively reflects the changes in force of each component.

Examining the Impact of Trust-Based Active Participation: An Empirical Study in Creative Industry That Adopt Digital Platform

The main challenge in building a creative industry that acquires a digital platform is the limited ideas used to encourage the presence of booming products and the limited understanding of employees of creative industry players in dealing with technological changes; this is in line with the phenomenon where 31.40% of digital business actors in Indonesia are still experiencing a decline in revenue in 2022. In connection with the main obstacles, this research aims to find constructs capable of mediating the role of technology in the form of Social Media Use to Work (SMUW) in its impact on Creative Performance (CP). Where SMUW, in many studies, has no significant effect on building CP. This study offers the role of Trust-Based Active Participation (TBAP) and Innovative Culture (IC) in mediating SMUW against CP. The object of this research is the creative industry that uses digital platforms, with a total sample of 188 businesses. This study empirically proves that SMUW does not significantly affect CP, but TBAP and IC can boost SMUW on CP with a a total effect of 0.384. From this achievement, it is proven empirically that TBAP and IC can fully mediate the role of SMUW on CP. In implementing the strategy, it was found that in order to optimize the role of SMUW for CP. This contributes to the domain of learning organization theory and middle ring dynamic capability.

Anatomy of the Lumbrical Muscles: Implications for Mechanical Advantage.

The lumbrical muscles comprise 4 intrinsic muscles of the hand and are involved in flexion of the metacarpophalangeal joint (MCPJ) and extension of the proximal interphalangeal and distal interphalangeal joints. The purpose of this study was to investigate the anatomical mechanics of the lumbrical muscles of the index, middle, ring, and small fingers. We evaluated 25 cadaver arms and measured the distance between the MCPJ and fingertip, the distance between the MCPJ and lumbrical muscle insertion, and the distance between the MCPJ and the most proximal lumbrical muscle origin. With these measurements we calculated the needed force, insertion ratio (length of the proximal, middle, and distal phalanx divided by the MCPJ to insertion distance), and lumbrical muscle length. We found that the force was significantly different between all fingers, except for the comparison of the index and ring finger (P = .34). In addition, we found that muscle length was significantly different between most the fingers, except for the comparison between the index and middle fingers (P = .24), and index and ring fingers (P = .20). There was no significant difference in insertion ratio. Our study suggests that the anatomical mechanics for the motor function of the lumbrical muscles are similar in all fingers. This could further imply that movements are equally precise in all fingers resulting in coordination with one another and, therefore, adequate hand function. IV.

Enhancing Chiroptical Responses in Helical Nanographenes via Geometric Engineering of Double [7]Helicenes.

Helical nanographenes with high quantum yields and strong chiroptical responses are pivotal for developing circularly polarized luminescence (CPL) materials. Here, we present the successful synthesis of novel π-extended double [7]helicenes (ED7Hs) where two helicene units are fused at the meta- or para-position of the middle benzene ring, respectively, as the structural isomers of the reported ortho-fused ED7H. The structural geometry of these ED7Hs is clearly characterized by single-crystal X-ray analysis. Notably, this class of ED7Hs exhibits bright luminescence with high quantum yields exceeding 40 %. Through geometric regulation of two embedded [7]helicene units from ortho-, meta- to para-position, these ED7Hs display exceptional amplification in chiroptical responses. This enhancement is evident in a remarkable approximate fivefold increase in the absorbance and luminescence dissymmetry factors (gabs and glum), respectively, along with a boosted CPL brightness up to 176 M-1 cm-1, surpassing the performance of most helicene-based chiral NGs. Furthermore, DFT calculations elucidate that the geometric adjustment of two [7]helicene units allows the precise alignment of electric and magnetic transition dipole moments, leading to the observed enhancement of their chiroptical responses. This study offers an effective strategy for magnifying the CPL performance in chiral NGs, promoting their expanded application as CPL emitters.

Effect of a halogen bond on the crystal structure of terphenyldicarboxylic acid derivatives.

The syntheses and structures of dimethyl [11,21:24,31-terphenyl]-14,34-dicarboxylate (1), dimethyl 22,25-diiodo[11,21:24,31-terphenyl]-14,34-dicarboxylate (2), potassium [11,21:24,31-terphenyl]-14,34-dicarboxylate (3) and dimethyl [1,1'-biphenyl]-4,4'-dicarboxylate (4) are reported. Neighboring phenyl rings in compounds 1, 3 and 4 have a planar structure (torsion angles are 0.6-4.1°) and the molecules are packed into regular layers. In the structure of the iodinated derivative of terphenyldicarboxylic acid (2), the middle benzene ring of the terphenyl fragment is rotated relative to the other rings by 64° due to the repulsion between the protons and the iodine atoms of neighboring rings. The formation of halogen bonds between iodine and oxygen atoms of the carbonyl group leads to the movement of molecules of one layer into another layer and the loss of layered structure. Potassium [11,21:24,31-terphenyl]-14,34-dicarboxylate (3) forms crystals with an ionic structure. The coordination number of the potassium cation is eight and the resulting coordination polyhedron is a distorted square antiprism. Dianions in the potassium salt crystal are packed in layers similar to the layers in the dimethyl ethers 1 and 4. Salt 3 has high thermal stability to 500°C.

Verstärkung von chiroptischen Eigenschaften in helikalen Nanographenen durch geometrische Anpassung von Doppel‐[7]Helicenen

AbstractHelikale Nanographene (NG) mit hohen Quantenausbeuten und starken chiroptischen Antworten sind entscheidend für die Entwicklung von lumineszenten Materialien mit zirkularer Polarisation (engl. circular polarized luminescence, CPL). Hier berichten wir von der erfolgreichen Synthese neuartiger π‐erweiterter Doppel‐[7]Helicene (ED7Hs), bei denen sich zwei Helicen‐Einheiten meta bzw. para am zentralen Benzenring befinden. Sie sind damit strukturelle Isomere des bekannten ortho‐ED7H. Die strukturelle Integrität und Geometrie der ED7Hs wurde eindeutig durch Röntgen‐Einkristalldiffraktometrie aufgeklärt. Die ED7Hs besitzen eine ausgeprägte Fluoreszenz mit Quantenausbeuten über 40 %. Durch Variation der relativen Positionen der Doppel‐[7]Helicene am zentralen Benzenring (ortho, meta, para) kann eine außergewöhnliche Verstärkung der chiroptischen Eigenschaften registriert werden. Diese Verbesserung zeigt sich in einem etwa fünffachen Anstieg der Absorbanz und Lumineszenz‐Dissymmetriefaktoren (gabs und glum) sowie einer erhöhten CPL‐Helligkeit von bis zu 176 M−1 cm−1, was die Leistung der meisten helicenbasierten chiralen NGs übertrifft. Des weiteren zeigen DFT‐Simulationen, dass die relative geometrische Lage der [7]Helicene eine präzise Anpassung der elektrischen und magnetischen Übergangsdipolmomente zur Folge hat, welche die beobachteten Verstärkungen der chiroptischen Eigenschaften erklären. Diese Studie liefert eine effektive Strategie zur Verstärkung der CPL‐Eigenschaften chiraler Nanographene, welche ihre Anwendbarkeit als CPL‐Emitter verbessert.

Stabilizing Azaheptacenes.

The symmetrical 7,16-diaza-6,8,15,17-tetrakis(triisopropylsilylethynyl)heptacene was obtained by a Pd-catalyzed reaction of a 2,3-diamino-1,4-diethynylanthracene with a 2,3-dibromo-1,4-diethynyl anthracene. Positioning the TIPS-ethynyl groups adjacent to the central ring suppresses dimerization via [4+4] cycloadditions and Diels-Alder reactions; the middle pyrazine ring renders this species stable to oxidation. A single crystal structure was obtained, and thin film transistors with μn = 0.042 cm2 V-1 s-1 were produced. Transposition of the alkynyl groups into the 5,8,15,18-positions with a quinoxaline unit in the center of the heptacene decreases the stability, as does the introduction of two more nitrogen atoms into the 5,18-positions. The hydrocarbon 6,8,15,17-tetrakis(triisopropylsilylethynyl)heptacene is reasonably stable with a half-life of 25 h in solution. Four correctly placed TIPS-ethynyl groups protect heptacene cores.

Heterometallic bridged Pt(II)‐Zn(II) complexes: Influence of the substituent in 4′‐position in inert terpy ligand on antigenotoxicity, potential antitumor activity and mechanism of interactions of the complexes with biomolecules

The synthesis and characterization of novel hetrometallic complexes [{cis‐PtCl(NH3)2(μ‐4,4′‐bipyridyl)ZnCl(terpy‐Cl)}](ClO4)2 (C1a), [{trans‐PtCl(NH3)2(μ‐4,4′‐bipyridyl)ZnCl(terpy)}](ClO4)2 (C2a), [{cis‐PtCl(NH3)2(μ‐pyrazine)ZnCl(terpy‐Cl)}](ClO4)2 (C3a) and [{trans‐PtCl(NH3)2(μ‐pyrazine)ZnCl(terpy‐Cl)}](ClO4)2 (C4a) (where terpy‐Cl = 4′‐chloro‐2,2′:6′,2′′‐terpyridine) was done. Acid–base titrations were performed by UV–Vis spectrophotometric method to evaluate the pKa values of corresponding aqua complexes. Interactions between complexes and important biomolecules, guanosine‐5′‐monophosphate (5′‐GMP) and glutathione (GSH) were examined by 1H NMR spectroscopy. The chloride substituent at the 4′ position on the middle pyridine ring of terpyridine ligand significantly affects the coordination of biomolecules, as well as overall stability of complexes. The complexes were evaluated in vitro for the antioxidant prevention of DNA damages. All tested novel complexes demonstrated a significant reduction in DNA damage against oxidative modifications of DNA caused by the hydroxyl and peroxyl radicals. Also, cytotoxicity evaluation showed that significant cytotoxicity occurs only after long‐term effect of C1a, C2a and C3a, complexes in HCT‐116 cells. Molecular docking studies predict results in agreement with experimental research.

EFFECT OF ORGANIC FERTILIZERS AND NUTRIENTS ON ANATOMICAL TRAITS OF RED BEETROOTS

A field experiment was conducted during fall season 2021-2022 In order to study the effect of soil as an agricultural medium, organic fertilizers (Vermecompost, cow manure) and foliar spraying of silicon and calcium on skin, bark and cambium ring thickness of three beetroot varieties (Red, Dark Red, and Cylindra). Seeds directly sown in the fields of Station A College of Agricultural Engineering Sciences - University of Baghdad - Al-Jadriya campus- Within RCBD a split-plot experiment, where the cultivars were the main unites, organic fertilizer, and foliar spray as the subunits, with three replicates, the number of treatments was 27. The results revealed that the triple interaction treatment of Dark Red, Vermicompost, and silicon spray V2S2F1 was superior in epidermis thickness, cortex thickness, and cambium ring thickness (55.00 μm, 78.90 μm, and 182.07μm) respectively, compared with Cylindra cultivar, soil medium, and spraying with distilled water V3S1F0, which produced the lowest averages (21.77 μm, 31.23 μm, 64.57 μm) respectively. The interaction treatment between Red cultivar, cow manure and spraying with distilled water V1S3F0 excelled in the thickness of the middle xylem ring ( 261.33 μm). Compared with the thinnest middle xylem (143.8 μm) in red cultivar roots treated with soil medium and distilled water.

QUANTITATIVE AUTOFLUORESCENCE IN CENTRAL SEROUS CHORIORETINOPATHY.

Central serous chorioretinopathy (CSC) is associated with pachychoroid and dysfunctional retinal pigment epithelium. Autofluorescence (AF) is typically altered. The authors performed this study to quantify these alterations using quantitative AF (qAF) in patients with CSC and in their fellow eye in comparison with a healthy control group. Patients with CSC and healthy controls were recruited prospectively. All patients received a full clinical examination including best-corrected visual acuity, enhanced depth imaging-optical coherence tomography, and qAF. Quantitative autofluorescence images were taken with a confocal scanning laser ophthalmoscope (Heidelberg Engineering). Quantitative autofluorescence values were assessed in specified regions of the inner eight and the middle ring of the Delori grid. In total, 141 eyes of 77 patients with CSC were included. Ninety eyes had a manifest CSC (group 1) while 51 fellow eyes (group 2) did not show signs of CSC. There were no significant differences of qAF values between these two groups: mean qAF values were 241.3 (inner eight) and 212.8 (middle ring) in group 1 and 235.9 (inner eight) and 210.0 (middle ring) in group 2 ( P = 1.0 and 1.0). We compared these eyes with healthy controls comprising 39 eyes. Quantitative autofluorescence signals (inner eight: 164.7; middle ring: 148.9) differed significantly compared with both CSC manifest ( P < 0.001) and fellow eyes ( P < 0.001). Our results show that patients with CSC have increased qAF values in both eyes with manifest CSC and asymptomatic, clinically unremarkable fellow eyes in comparison with healthy controls. This finding suggests that qAF alterations are present even before clinical signs can be observed.

Looking for optimal concentric ring electrodes: influence of design aspects on their performance

Concentric ring electrodes (CREs) allow improved spatial resolution, reduced crosstalk and interference, and increased bandwidth in the sensing of bioelectrical activity. A wide variety of designs have been used, but their selection is rarely well-founded. The aim of this work is to assess the implications of aspects of CRE design such as the distance between poles, their width and their maximum diameter on aspects such as the signal amplitude (and, therefore, quality), Laplacian estimation error and spatial selectivity (SS). For this purpose, a finite dimensional model of the CRE was used, and its response to the activity of an electric dipole of variable depth was simulated via finite element method modeling. Our results show that increasing the electrode size increases the error to a greater extent than the signal amplitude increases. Pole widths should be as small as possible. The middle ring of the tripolar CRE should be as far away as possible from the central disc. Tripolar CREs typically outperform bipolar CREs of the same outer diameter, significantly reducing the Laplacian estimation error and improving the SS at the cost of a small decrease in signal amplitude. Our results also show that the design of current commercial versions of CREs can be optimized. Furthermore, we propose a methodology that facilitates the selection of an adequate CRE configuration based on the specifications for CRE performance and practical aspects, such as the depth of activity sources to be recorded from and/or the maximum size of electrodes to be used. The monitoring and analysis of bioelectrical signals in a wide range of applications can benefit from the enhanced electrode design and methodology proposed in this work.