Microwave Photonic Techniques Research Articles

Radio‐Frequency Linear Analysis and Optimization of Silicon Photonic Neural Networks

Broadband analog signal processors utilizing silicon photonics have demonstrated a significant impact in numerous application spaces, offering unprecedented bandwidths, dynamic range, and tunability. In the past decade, microwave photonic techniques have been applied to neuromorphic processing, resulting in the development of novel photonic neural network architectures. Neuromorphic photonic systems can enable machine learning capabilities at extreme bandwidths and speeds. Herein, low‐quality factor microring resonators are implemented to demonstrate broadband optical weighting. In addition, silicon photonic neural network architectures are critically evaluated, simulated, and optimized from a radio‐frequency performance perspective. This analysis highlights the linear front‐end of the photonic neural network, the effects of linear and nonlinear loss within silicon waveguides, and the impact of electrical preamplification.

7-Core Fiber-Based High-Resolution Omnidirectional Vector Bending Sensor Enabled by Microwave Photonics Filter

We proposed and experimentally demonstrated a high-resolution omnidirectional vector bending sensor based on 7-core fiber Mach-Zehnder interferometers (MZIs), which is interrogated by the microwave photonics technique. The sensor is composed of three MZIs in the 7-core fiber, and each MZI consists of two symmetric outer cores. Instead of using the traditional wavelength demodulation method, which has the drawback of very limited resolution due to the used optical spectrum analysis devices, e.g., optical spectrum analyzer (OSA), the proposed sensor is interrogated by high-resolution microwave photonics filter (MPF) system, which is capable of offering up to KHz level measurement resolution. As a result, curvature measurement with resolution of 0.0213 m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-1</sup> is demonstrated when the used resolution of vector network analyzer (VNA) is 500 kHz. Thanks to the ultra-high measurement resolution of VNA (∼KHz), the curvature resolution can achieve 4.27 х 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-5</sup> m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-1</sup> in theory, which is 2 orders of magnitude higher than the traditional wavelength demodulation-based fiber bending sensors. The measured curvature sensitivity of the MZI exhibits highly bending direction dependence, attributed to different strain variation under distinct bending angle. In addition, owing to the different angular positions of cores of the MZI in the 7-core fiber, the MZIs have differential response to fiber bending. This feature has been used to develop vector bending sensing, which is manage to determine the bending direction by using any two MZIs, and the obtained average relative errors for the retrieved curvature and bending direction are 2.57% and 0.86%, respectively. The proposed sensor possesses the unique advantages of high sensitivity and high resolution over the state-of-the-art technology, which is very promising for omnidirectional vector bending sensing in the future.

Performance Evaluation of Photonics-Based Coherent MIMO Radar Systems for Maritime Surveillance

Multiple-input multiple-output (MIMO) radars offer significant advantages over conventional standalone radars in terms of target detection and localization capabilities. However, to fully exploit their potential, such systems require excellent time and phase synchronization among the central unit and the radar heads. Only recently, thanks to microwave photonics (MWP) techniques, it has been possible to develop the first coherent MIMO radar demonstrators. In this paper, a simulation tool in MATLAB programming language is proposed to model coherent MIMO radars based on MWP techniques in maritime surveillance applications. Moreover, a novel approach for estimating the radar cross section of extended maritime targets is presented. The system performance in co-located and distributed MIMO configuration, as well as in single- and multi-band operations, is evaluated by means of relevant key performance indicators (KPIs). Simulations are carried out in two close-to-reality scenarios. In the first, a co-located MIMO radar is mounted on top of a patrolling vessel. In the second, a distributed MIMO radar is deployed inside a port. The proposed KPIs are analyzed in terms of both geometric and frequency diversities of the system, laying the foundations for general system optimization criteria valid in any given surveillance application.

Augmentation of Sensitivity of FBG Sensor Using Microwave Photonics and Nonlinear Effect

A simple and unique scheme of high sensitive Fiber Bragg Grating(FBG) interrogation system based on microwave signal measurement utilizing the concept of microwave photonics and nonlinear Four wave mixing(FWM), is proposed. The concept of FWM process is combined with microwave photonics to enhance the sensitivity of FBG sensor. The strain induced wavelength shift of the sensing FBG is translated to higher wavelength shift of the corresponding higher order FWM signals on either side of FBG sensor wavelength in opposite directions. Thus the wavelength separation between the FWM signals increases with small increase in strain. Utilizing the FWM effect and microwave photonics technique, the microwave phase difference is altered, which ultimately is converted to significant change in RF intensity. A novel mathematical relationship relating FWM, applied strain and the microwave power of the proposed scheme is established. A high strain sensitivity of 36.52 μV/με (26.67 μW/με) is attained using the proposed FWM and microwave photonics technique against initial sensitivity of 4.9 μV/με (0.48 μW/με) using only microwave photonics technique. The proposed scheme automatically compensates the temperature variations and eliminates the requirement of high dispersive component to enhance the sensitivity.

МЕТОД ГЕНЕРАЦИИ СВЕРХШИРОКОПОЛОСНЫХ СВЧ-СИГНАЛОВ С ЛИНЕЙНО-ЧАСТОТНОЙ МОДУЛЯЦИЕЙ НА ОСНОВЕ САМОГЕТЕРОДИНИРОВАНИЯ ИЗЛУЧЕНИЯ ЛАЗЕРНОГО ДИОДА

In this paper, microwave photonic technique of ultrawideband linearly frequency modulated signals generation is proposed. The proposed method based on direct modulation of the laser diode current, which provides a periodic change in the emission frequency. The Michelson interferometer summarizes laser signal and its replica with time delay exceeding 10 ms, which, in turn, is defined by time difference between arms. Optoelectronic conversion is performed in high-speed high-power photodiode. The proposed approach makes it possible to generate microwave signals with linear frequency modulation in the frequency range up to several tens of gigahertz by means of laser pump current modulation in the frequency range less than 100 MHz. The method of ultra-wideband microwave signals generation is implemented using a Michelson fiber-optic interferometer with Faraday mirrors. Such interferometer topology provides a doubling of the path length, and reduced gyroscopic effects due to a counter-propagating double pass. Changing the parameters of the generated microwave ultrawideband signals with frequency modulation is achieved by pump current shape and amplitude control. It is also proposed to use real-time oscilloscope without need of changing of the internal structure of such generator to pre-tune it. Time-frequency analysis is used to extract frequency versus time dependence. By so doing, direct impulse response estimation is performed. This method allows to characterize laser diode frequency response for arbitrary microwave waveform generation by means of pump current waveform calculation from experimental data.

Microwave Photonics Advancements in Radar Application

Microwave photonics (MWP) Technology brings Microwave and optical domains together. Due to its extraordinary capabilities and solution especially towards generation, transmission and processing of Microwave signals, the MWP field has potential to break barrier, which was not possible with RF technology alone. MWP technologies provide new opportunities in many areas like 5G networks, Advanced Radar and Internet of things. As demand for multi-functionality and reduced size is growing in every field, Radar is no exception. Radar systems capabilities in terms of functionality, precision, response time have significantly improved in past decades. MWP technologies are one of the key factors in that. With Modern photonics technologies Radar performance in terms of Speed, resolution, coverage, precise target identification has improved drastically. To understand the photonics technologies in detail, this paper is designed, which highlights the important features of Microwave photonics techniques applied in Radar and its subsystems

Towards High-Resolution Imaging With Photonics-Based Time Division Multiplexing MIMO Radar

A photonics-based time division multiplexing (TDM) multiple-input and multiple-output (MIMO) radar is proposed to realize high-resolution imaging. In this MIMO radar, multiple transmitters generate time-domain orthogonal linearly frequency modulated (LFM) signals based on microwave photonic frequency octupling and optical TDM technique, and multiple receivers implement dechirping of the multi-channel radar echoes based on microwave photonic frequency mixing. The microwave photonic techniques make the system capable to generate and process broadband radar signals, and the TDM yields a high spectral efficiency, which allows a large bandwidth in each transmitter and receiver. Meanwhile, the TDM-MIMO ensures complete orthogonality between different channels and enables good flexibility in arranging more transmit and receive channels. Therefore, the proposed photonics-based TDM-MIMO radar can achieve both high range resolution and high angular resolution. In the experiment, a photonics-based 4 × 8 TDM-MIMO radar is established which has an operation bandwidth of 8 GHz in each transmit channel. The range resolution and angular resolution are estimated to be 1.9 cm and 1.1°, respectively. A broadband back projection (BP) imaging algorithm with both frequency and time-delay dependent phase compensation is proposed, based on which high resolution imaging of single and complex targets is achieved.

A Microwave Photonic-Assisted Fiber Loop Ring Down System with Multi-Sensing Function

In this letter, we demonstrate a fiber-loop ring down (FLRD) multi-function sensing system, which is assisted by microwave photonic technique. The temperature and curvature sensing characteristics of the FLRD system are studied. The ring-down curve in the time domain can be acquired by taking the inverse Fourier transform (IFFT) of the frequency response of a microwave photonics filter (MPF). The temperature and curvature information can then be evaluated simultaneously based on the calculated ring-down curves. Compared with the traditional time domain measurement, the system is based on pure frequency domain measurement from a microwave photonic configuration, which reduces the requirements of the light source and has the features of fast responding and easy networking. The sensitivity of the system is measured to be <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$0.425~\mu \text{s}/^{\circ }\text{C}$ </tex-math></inline-formula> in the sensing range of 30~70 °C and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$0.1553~\mu \text{s}$ </tex-math></inline-formula> /cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−1</sup> in the sensing range of 0.8696~1.0526 cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−1</sup> . The experimental results agree well with the theoretical predictions.

Design and Performance Estimation of a Photonic Integrated Beamforming Receiver for Scan-on-Receive Synthetic Aperture Radar

Synthetic aperture radar is a remote sensing technology finding applications in a wide range of fields, especially related to Earth observation. It enables a fine imaging that is crucial in critical activities, like environmental monitoring for natural resource management or disasters prevention. In this picture, the scan-on-receive paradigm allows for enhanced imaging capabilities thanks to wide swath observations at finer azimuthal resolution achieved by beamforming of multiple simultaneous antenna beams. Recently, solutions based on microwave photonics techniques demonstrated the possibility of an efficient implementation of beamforming, overcoming some limitations posed by purely electronic solutions, offering unprecedented flexibility and precision to RF systems. Moreover, photonics-assisted RF beamformers can nowadays be realized as integrated circuits, with reduced size and power consumption with respect to digital beamforming approaches. This paper presents the design analysis and the challenges of the development of a hybrid photonic-integrated circuit as the core element of an X-band scan-on-receive spaceborne synthetic aperture radar. The proposed photonic-integrated circuit synthetizes three simultaneous scanning beams on the received signal, and performs the frequency down-conversion, guaranteeing a compact 15 cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> -form factor, less than 6 W power consumption, and 55 dB of dynamic range. The whole photonics-assisted system is designed for space compliance and meets the target application requirements, representing a step forward toward a deeper penetration of photonics in microwave applications for challenging scenarios, like the observation of the Earth from space.

All-Optical Pulsed Signal Doppler Frequency Shift Measurement System

A simple and all-optical Doppler frequency shift (DFS) measurement system is presented. It is based on a dual-drive Mach Zehnder modulator (DDMZM) driven by a transmitted signal and an echo signal received by an antenna. A low-frequency sawtooth wave is applied to the DDMZM DC port to frequency shift the carrier and sidebands generated by the transmitted signal. Beating of a frequency-shifted transmitted signal sideband and an echo signal sideband at the photodetector produces a low-frequency electrical signal. The DFS, and consequently the speed and moving direction of a target, can be obtained from the frequency of this low-frequency electrical signal. The DDMZM used in the proposed DFS measurement system does not need to be operated at a specific point in the transfer function and hence it has no bias drift problem. The proposed DFS measurement technique can be used in both CW and pulsed radar systems. Experimental results demonstrate the proposed DFS measurement system has a wide operating frequency range of 10 GHz to 19.95 GHz, small DFS measurement error of less than ±0.6 Hz and long-term stable performance. Results also demonstrate, for the first time, DFS measurement of a pulsed signal using a microwave photonic technique.

Determining the Stable Injection Locking of a Fabry-Pérot Laser by Observing the RF Spectral Components Generated by a Low-Reflectivity External Cavity

A novel approach to monitoring the laser injection-locking (IL) state is proposed and verified using the side-mode suppression ratio (SMSR). In a photonics experiment for laser IL, an optical spectrum analyzer with the conventional criterion of a 35-dB SMSR is conventionally used to detect the locking state of a Fabry–Pérot (FP) laser with multiple longitudinal modes to an external master laser with one longitudinal mode. Since the 35-dB criterion is not always a sufficient locking condition, we propose a microwave-photonic technique to determine the stable-locking regime based on the observation of the radio-frequency (RF) components. A novel approach to monitoring the generated additional spectral components uses the well-known delayed-self-homodyne technique and the RF spectrum analyzer. For the novel generation of additional longitudinal groups on each FP laser’s resonator mode in the optical spectrum and consequently the overlapping RF components in the RF spectrum, an additional external resonator with low reflectivity was connected to the slave FP laser. The novel monitoring approach was experimentally verified by connecting a 1-m-long external cavity with 0.5% reflectivity and observing the optical IL phenomenon of a 1550-nm FP semiconductor laser.

High-resolution polymer optical fibre humidity sensor utilizing single-passband microwave photonic filter

Water affinity property of the polymer optical fibre (POF) makes it possible for humidity sensing. In this paper, we propose and experimentally demonstrate a high-resolution POF-based humidity sensor that utilizes microwave photonic interrogation technique. A Mach-Zehnder interferometer (MZI) of one arm inserted with the POF is used as the interrogator, and a single-passband microwave photonic filter is developed for interrogation. The change of the humidity is then converted to the frequency shift of the radio-frequency (RF) filter’s passband. A humidity sensor with sensitivity of 84 MHz/RH% and resolution of 0.0119 RH% is achieved in the experiment. Thanks to the introduction of microwave photonic interrogation technique, the proposed humidity sensor owns the abilities of high resolution and anti-vibration. These advantages make it suitable for the potential applications with high precision requirement or in an unstable environment.

Demodulation of a polarization‐maintaining photonic crystal fiber load sensor with high resolution using a microwave photonic filter

AbstractA new demodulation technique for polarization‐maintaining photonic crystal fiber pressure sensor with high resolution based on a simple photonic microwave filter has been proposed and demonstrated. Unlike the conventional methods that use optical interferometry and optical spectrum analysis, the proposed method adopts microwave photonics technique. The relationship between load and the notch frequency of the filter is studied. By measuring the notch frequency of the filter, the pressure can be determined and the sensing sensitivity is greatly increased. The sensitivity is as high as 15.625 MHz/N which satisfied well with the theoretical simulation.

Microwave Photonic Sensors

Microwave photonics is a field that studies the interaction between microwave and optical waves for the generation, transmission, processing, and measurements of microwave signals by means of photonics, to take advantage of the high speed and broad bandwidth offered by modern photonics. Microwave photonic sensors are one of the active sub-fields that uses microwave photonic techniques to achieve high-speed and high-resolution measurements. In this article, microwave photonic techniques for optical sensing demonstrated in the past few years will be reviewed including high-speed and high-resolution sensing based on heterodyne beating of two optical wavelengths, the use of an optoelectronic oscillator to translate the optical wavelength shift to a microwave frequency change, and the use of wavelength-to-time mapping to translate the sensing information from the optical wavelength domain to the microwave frequency domain, to increase the interrogation speed and resolution. The use of photonic integrated circuits to achieve high-speed and high-resolution microwave photonic sensing will also be discussed.

Photonics-Based Serrodyne Microwave Frequency Translator With Large Spurious Suppression and Phase Shifting Capability

A Serrodyne microwave frequency translator implemented using a microwave photonic technique is presented. It is based on two dual-drive Mach-Zehnder modulators connected in parallel where one of the modulators is operated as an optical phase modulator driven by a sawtooth wave. It is capable of simultaneously shifting the frequency and phase of an input microwave signal. The frequency translator is designed to largely suppress the undesired carrier and sidebands and to minimise the frequency translation loss. Results on the frequency translator demonstrate -1 to 1 MHz frequency translation of multiple microwave signals with a large spurious suppression ratio of 34 to 41 dB and a wide bandwidth of 2 to 18 GHz. Simultaneous frequency and phase shifting operation is also demonstrated.

Instantaneous microwave frequency measurement using few-mode fiber-based microwave photonic filters.

Instantaneous frequency measurement (IFM) of microwave signals using photonic methods provides a novel and efficient approach for fast and broadband radio frequency (RF) signal analysis. Here, we propose and experimentally demonstrate a photonic-assisted IFM method utilizing a few-mode fiber-based microwave photonic technique. By offset splicing the few-mode fiber (FMF) with a single mode fiber, both LP01 and LP11 modes can be excited, which is used to develop a microwave photonic filter (MPF). A detailed analysis of the FMF as the true time delay line is presented. An amplitude comparison function (ACF) that is the ratio of frequency response traces of an MPF pair is established, which is used to determine the unknown microwave frequency instantaneously. The proof-of-concept experiment demonstrates a frequency measurement range of 0.5 GHz to 17.5 GHz and a measurement accuracy of ±0.2 GHz in most of the frequency points. The proposed system has the merits of simplicity, cost-effectiveness, compactness and robustness.

High-Resolution Detection of Wavelength Shift Induced by an Erbium-Doped Fiber Bragg Grating

We analyze theoretically and verify experimentally a high-resolution and low-cost method to detect wavelength shift induced by an Erbium-doped fiber Bragg grating. A π-phase-shifted fiber Bragg grating on a temperature controlling setup is employed to achieve tunable single-sideband modulation. To further enhance measurement stability and diminish operational complexity, an asymmetric phase-shifted fiber Bragg grating is developed to reflect wide single-sideband modulation signals and avoid the tuning of the optical carrier wavelength. Through the using of microwave photonics technique, the wavelength shift of the Erbium-doped fiber Bragg grating induced by laser pumping is mapped onto the amplitude variation of the beat signal. The results indicate 1 GHz frequency shift, corresponding to 0.008 nm wavelength shift in the 1550 nm band, is able to be detected. The resolution can be further improved by using a more accurate temperature controlling system. Furthermore, our approach offers an alternative method to detect weak temperature and strain changes on chips or other sensing systems with high accuracy.

Adaptive photonic RF spectral shaper.

The radio frequency spectral shaper is an essential component in emerging multi-service mobile communications, multiband satellite and radar systems, and future 5G/6G radio frequency systems for equalizing spectral unevenness, removing out-of-band noise and interference, and manipulating multi-band signal simultaneously. While it is easy to achieve simple spectral functions using either conventional microwave photonic filters or the optical spectrum to microwave spectra mapping techniques, it is challenging to enable complex spectral shaping functions over tens of GHz bandwidth as well as to achieve point-by-point shaping capability to fulfill the needs in dynamic wireless communications. In this paper, we proposed and demonstrated a novel spectral shaping system, which utilizes a two-section algorithm to automatically decompose the target RF response into a series of Gaussian functions and to reconstruct the desired RF response by microwave photonic techniques. The devised spectral shaping system is capable of manipulating the spectral function in various bands (S, C, and X) simultaneously with step resolution of as fine as tens of MHz. The resolution limitation in optical spectral processing is mitigated using the discrete convolution technique. Over 10 dynamic and independently adjustable spectral control points are experimentally achieved based on the proposed spectral shaper.

Integration of Rotation Estimation and High-Order Compensation for Ultrahigh-Resolution Microwave Photonic ISAR Imagery

The microwave photonic (MWP) radar technique is capable of providing ultrawide frequency bandwidth waveforms to generate ultrahigh-resolution (UHR) inverse synthetic aperture radar (ISAR) imagery. Nevertheless, conventional ISAR imaging algorithms have limitations in focusing UHR MWP-ISAR imagery, where high-precision high-order range cell migration (RCM) and phase correction are crucially necessary. In this article, a UHR MWP-ISAR imaging algorithm integrating rotation estimation and high-order motion terms compensation is proposed. By establishing the relationship between parametric ISAR rotation model and high-order motion terms, an average range profile sharpness maximization (ARPSM) is developed to obtain rotation velocity by using nonuniform fast Fourier transform (NUFFT). Second-order range-dependent RCM is corrected with parametric compensation model by using the rotation velocity estimation. Furthermore, the spatial-variant high-order phase error is extracted to compensation by the entire image sharpness maximization (EISM). A new imaging framework is established with two one-dimensional (1-D) parameter estimations: ARPSM and EISM. Extensive experiments demonstrate that the proposed algorithm outperforms traditional ISAR imaging strategies in high-order RCM correction and azimuth focusing performance.

Characterization of Optically-Reconfigurable Metasurfaces by a Free Space Microwave Bistatic Technique

Microwave performance extraction of optically-controlled squared frequency-selective surface (FSS) structures printed on highly resistive (HR) silicon substrate are presented, from a innovative bistatic microwave photonic characterization technique operating in the 40 to 60 GHz frequency range, commonly used for radar cross section (RCS) measurements. According to typical physical photon absorption phenomenon occurring in photoconductive materials, these structures demonstrate experimentally a bandpass filtering frequency response cancellation through reflection coefficient measurements, under specific incident collective illumination in the Near-infrared region (NIR). This behaviour is attributed to their microwave surface impedance modification accordingly to the incident optical power, allowing ultrafast reconfigurability of such devices by optics