Microwave Diagnostics Research Articles

The 140 GHz notch filter development for millimeter-wave diagnostics protection on the stellarator Wendelstein 7-X

The notch filter plays a crucial role as a protective component in microwave diagnostics, primarily by addressing issues related to catastrophic interference. Designed for millimeter-wave diagnostics on the stellarator Wendelstein 7-X (W7-X), a WR-6 waveguide-based notch filter has been successfully developed to effectively isolate leakage from auxiliary heating gyrotrons operating at 140 GHz. The filter incorporates cylindrical cavities resonating at 140 GHz for the TE11p mode, with coupling structures that are designed and optimized for high-efficiency coupling. This configuration simplifies fabrication, thereby ensuring high-yield production. Experimental fabrication and in-house characterization confirm the notch filter's exceptional performance, with over 60 dB rejection in the vicinity of 140 GHz and low insertion loss (< 2 dB) above and below the notch frequency across a broad frequency bandwidth (121–138 GHz, 142–163 GHz). The utilization of this high-frequency structure fabrication technology can be applied to millimeter-wave diagnostics on other machines. In addition to the design elements of the notch filter, this paper also provides a detailed discussion of the fabrication process and methodology.

Microwave diagnostics of flare plasma by the direct fitting method based on data from the Siberian Radioheliograph

In this paper, we analyze images and the frequency spectrum of microwave emission in the maximum of brightness distribution in the January 20, 2022 and July 16, 2023 flares recorded by the Siberian Radioheliograph in the 3–6 GHz and 6–12 GHz ranges. We use the obtained spectrum data for radio diagnostics of magnetic field strength and orientation, plasma density, and parameters of accelerated particles in a radio source. The radio diagnostics is carried out by a method based on minimizing the functional containing the intensities of theoretically calculated and observed frequency spectra of left-polarized and right-polarized emission. Since the form of such a multidimensional functional is quite complex, and it is not possible to minimize it by standard approaches, we employ a genetic minimization method. The radio diagnostics allows us to determine features of the dynamics of the magnetic field intensity and orientation, as well as the density and the energy spectral index of non-thermal electrons in the region of maximum brightness of the radio source. We have found that during the growth phase of the main radiation peaks the magnetic field decreases, whereas during the decay phase, on the contrary, it increases. The rate of these changes varies from a few G/s to 11 G/s for the January 20, 2022 flare and is about 1 G/s for the July 16, 2023 flare.

Frontier system-on-chip (SoC) technology for microwave diagnostics (invited).

The next generation of fusion reactors, exemplified by projects such as the Demonstration Power Plant following the International Thermonuclear Experimental Reactor, faces the monumental challenge of proving the viability of generating electricity through thermonuclear fusion. This pursuit introduces heightened complexities in diagnostic methodologies, particularly in microwave-based diagnostics. The increased neutron fluence necessitates significant reductions in vessel penetrations and the elimination of internal diagnostics, posing substantial challenges. SoC technology offers a promising solution by enabling the miniaturization, modularization, integration, and enhancing the reliability of microwave systems. After seven years of research, our team successfully pioneered the V- and W-band system-on-chip approach, leading to the development of active transmitters and passive receiver modules applied in practical settings, notably within the DIII-D tokamak project. Arrays of these modules have supported microwave imaging diagnostics. New physics measurement results from the Electron Cyclotron Emission Imaging system on DIII-D provide compelling evidence of improved diagnostics following the adoption of SoC technology. Furthermore, we achieved a breakthrough in developing an F-band SoC, advancing higher frequency capabilities for fusion devices. These achievements represent a significant leap forward in fusion diagnostic technology, marking substantial progress toward establishing reliable and efficient plasma diagnostics for future fusion reactors.

Electromagnetic transmission of two-dimensional inhomogeneous plasma photonic crystal

A 2D tunable plasma photonic crystal (PPC) was constructed and implemented experimentally over a frequency range of 1 GHz–12 GHz within the electromagnetic spectrum. The PPC was simulated using an inhomogeneous model of a plasma tube based on microwave diagnostics and numerical simulations. The simulation results were found to be in good agreement with the experimental results. The data indicates that for TM polarization, localized plasmons will be excited at various positions within the tube, which does not rely on an interface with the medium, resulting in a broad forbidden band due to plasma inhomogeneity. The bandwidth of this band is consistent with the plasma frequency range. Furthermore, a lattice resonance band is observed, which is related to the incident angle. The cutoff effect of inhomogeneous PPC for TE polarization can be predicted by averaging the plasma parameters. The structure or plasma parameters can be adjusted to tune all the bands mentioned above. These findings can be used as a reference for applications in communication and microwave devices, and could potentially be utilized as a diagnostic tool for plasma parameters.

Laser and microwave instrumentation for ITER and future reactors

ITER diagnostics include an extensive set oflaser and microwave diagnostics to give access to a wealth of information on thecore and edge plasma and to support high performance operation of ITER. Forexample, Core and Edge Thomson scattering systems build detailed density andtemperature profiles on time scales much faster than τ E to follow transientevents; ECE and reflectometry add time resolution to follow MHDevents. Implementing these diagnostics is challenging, needing a panoply oftechnologies to keep them functioning reliably for thousands of hours despiteextreme events such as disruptions and wall conditioning cycles. Shielding,shutters and cleaning systems protect the forward elements of most opticalsystems from the build-up of deposits and damage. Still, plasma-facing mirrorsmust survive laser loads and endure erosion, deposition and in-situ RFcleaning. Calibration and monitoring systems ensure accurate and drift-freeoperation. These support systems are also not straightforward and requiredspecific R&D. Access also drives the design: to deal with the neutronand gamma sources yet allow maintenance of activated components, ITER useslarge, multi-purpose ports that couple otherwise distinct systems into modulesfor maintenance. Machine movement requires provisions to maintain alignment andcalibration, from these port plugs, shown in figure 1, to theaccessible areas 10–50 m away. A final complication comes from the difficulty ofemploying electronics near the plugs. Extensive qualification for radiationresistance is needed. This paper examines design adaptations that ITER adoptedfor its near-reactor environment, consider the lessons learnt from the ITERdesign activity specifically for laser and microwave systems and lays out somepossible evolution paths for the reactor diagnostician that must follow a moreindustrial approach.

A synthetic diagnostics platform for microwave imaging diagnostics in tokamaks

Interpreting experimental diagnostics data in tokamaks, while considering non-ideal effects, is challenging due to the complexity of plasmas. To address this challenge, a general synthetic diagnostics (GSD) platform has been established that facilitates microwave imaging reflectometry and electron cyclotron emission imaging. This platform utilizes plasma profiles as input and incorporates the finite-difference time domain, ray tracing and the radiative transfer equation to calculate the propagation of plasma spontaneous radiation and the external electromagnetic field in plasmas. Benchmark tests for classical cases have been conducted to verify the accuracy of every core module in the GSD platform. Finally, 2D imaging of a typical electron temperature distribution is reproduced by this platform and the results are consistent with the given real experimental data. This platform also has the potential to be extended to 3D electromagnetic field simulations and other microwave diagnostics such as cross-polarization scattering.

Electrodynamic Properties of Resonator Probes for Local Microwave Diagnostics of Nanoelectronic Objects

Electrodynamic Properties of Resonator Probes for Local Microwave Diagnostics of Nanoelectronic Objects

Microwave Diagnostics of Electrical Discharges in an Artificial Cloud of Charged Water Drops

Microwave Diagnostics of Electrical Discharges in an Artificial Cloud of Charged Water Drops

The latest developments of microwave diagnostics for high temperature plasma in ELVA-1 company

For nearly 30 years, we have been designing and supplying instruments for microwave diagnostics of high temperature plasma. This report provides a description of the mm-wave components we utilize to make diagnostics within the frequency range of 26–330 GHz. While most of these components are standard and readily available on the market, we have also developed a few specific devices that simplify the architecture of our instruments. The article includes descriptions of these devices: Backward Wave Oscillators (BWO), Impact Ionization Avalanche Transit-Time diode (IMPATT) sources, IMPATT Active Frequency Multipliers (AFM), Noise Sources, and Electronically Controlled Attenuators. Furthermore, we offer an overview of the microwave plasma diagnostics we have supplied, including ECE radiometers operating at 50–220 GHz, as well as heterodyne interferometers operating at fixed frequency 94 GHz, 140 GHz, or 300 GHz. We also discuss methods employed to ensure measurement stability and present the achieved results. The advent of the new era of modern Monolithic Microwave Integrated Circuit (MMIC) based devices has brought forth exciting possibilities. As an example, we discuss the upgrade of the low noise receiver for the Collective Thomson Scattering (CTS) diagnostic at Wendelstein 7-X, which enables ion temperature measurements in the plasma core [1]. Lastly, we provide a list of MMIC-based devices that are currently available and have garnered the attention of the plasma diagnostics community.

Microwave diagnostics of pulsed atmospheric discharge with electrolytic electrode and long‐lived luminous formation in its afterglow

AbstractThe Gatchina discharge phenomenon holds significant promise as a laboratory model for simulating ball lightning. However, crucial aspects concerning the plasma components of the resulting afterglow remain unresolved. Notably, the measurement of the electron density, a critical parameter, has not been fully achieved thus far. In this study, microwave diagnostics and video recording were employed during a pulsed Gatchina discharge, along with synchronous measurement of discharge current and voltage. Distinct antennas were positioned at different heights to enable separate diagnosis of the discharge and the ensuing long‐lived afterglow. The findings revealed that during the active phase of the Gatchina discharge, the plasma density was substantial enough to cause reflection of an electromagnetic wave with a frequency of 20 GHz from this highly conductive object. In the afterglow, the signal experienced only a moderate weakening of 10–20 percent, facilitating the determination of the time dependence of average electron density during the afterglow's passage between the two antennas. These measurements verified the unusually slow plasma decay in the afterglow of the Gatchina discharge, suggesting the potential significance of chemi‐ionisation processes involving long‐lived (metastable) particles.

Diagnostics of Atmospheric Plasma Jets of Helium and Argon Barrier Discharge in a Cylindrical Microwave Cavity Resonator

Introduction. Technologies related to the use of low-temperature atmospheric plasmas are developing at a rapid pace. Creation of new low-temperature plasma sources for specific applications requires monitoring of dynamic processes in such discharges with a high time resolution. Electron concentration is one the most important plasma characteristics, which can be very low for a low-temperature atmospheric pressure plasma. However, the methods currently available for diagnostics of gas-discharge plasmas are either characterized by insufficient sensitivity or unable to monitor dynamic processes in non-stationary discharges. In this regard, the development of new diagnostic approaches to low-temperature atmospheric plasma seems to be a relevant research direction.Aim. To develop a diagnostic method for an atmospheric plasma with a low gas temperature and a low electron concentration in a cylindrical microwave resonator.Materials and methods. The proposed diagnostic method is based on the well-known principle of measuring the frequency shift and the Q-factor of the eigenmodes of the microwave resonator, inside which the plasma under study is located.Results. Measurements of the atmospheric barrier discharge plasma jets in a helium and argon stream in a cylindrical microwave resonator were performed. The proposed geometry made it possible to significantly increase the sensitivity of measurements. It became possible to exclude the effect of polarization degeneracy in a round cylindrical resonator. The developed system was also tested on test objects with a known value of permittivity.Conclusion. A method for microwave diagnostics of stationary and non-stationary cold atmospheric plasma jets in a cylindrical resonator, inside which transmitting and receiving antennas are installed, as well as an orthogonal thin conductor preventing the excitation of undesirable modes, was developed.

Recombination of vibrationally cold N2+ ions with electrons.

Recombination of vibrationally cold N2+ ions with electrons was studied in the temperature range of 140-250K. A cryogenic stationary afterglow apparatus equipped with cavity ring-down spectrometer and microwave diagnostics was utilized to probe in situ the time evolutions of number densities of particular rotational and vibrational states of N2+ ions and of electrons. The obtained value of the recombination rate coefficient for the recombination of the vibrational ground state of N2+ with electrons is αv=0 = (2.95 ± 0.50) × 10-7(300/T)(0.28±0.07)cm3s-1, while that for the first vibrationally excited state was inferred as αv=1 = (4 ± 4) × 10-8cm3s-1 at 250K.

Advances, Challenges, and Future Perspectives of Microwave Reflectometry for Plasma Position and Shape Control on Future Nuclear Fusion Devices.

Providing energy from fusion and finding ways to scale up the fusion process to commercial proportions in an efficient, economical, and environmentally benign way is one of the grand challenges for engineering. Controlling the burning plasma in real-time is one of the critical issues that need to be addressed. Plasma Position Reflectometry (PPR) is expected to have an important role in next-generation fusion machines, such as DEMO, as a diagnostic to monitor the position and shape of the plasma continuously, complementing magnetic diagnostics. The reflectometry diagnostic uses radar science methods in the microwave and millimetre wave frequency ranges and is envisaged to measure the radial edge density profile at several poloidal angles providing data for the feedback control of the plasma position and shape. While significant steps have already been given to accomplish that goal, with proof of concept tested first in ASDEX-Upgrade and afterward in COMPASS, important, ground-breaking work is still ongoing. The Divertor Test Tokamak (DTT) facility presents itself as the appropriate future fusion device to implement, develop, and test a PPR system, thus contributing to building a knowledge database in plasma position reflectometry required for its application in DEMO. At DEMO, the PPR diagnostic's in-vessel antennas and waveguides, as well as the magnetic diagnostics, may be exposed to neutron irradiation fluences 5 to 50 times greater than those experienced by ITER. In the event of failure of either the magnetic or microwave diagnostics, the equilibrium control of the DEMO plasma may be jeopardized. It is, therefore, imperative to ensure that these systems are designed in such a way that they can be replaced if necessary. To perform reflectometry measurements at the 16 envisaged poloidal locations in DEMO, plasma-facing antennas and waveguides are needed to route the microwaves between the plasma through the DEMO upper ports (UPs) to the diagnostic hall. The main integration approach for this diagnostic is to incorporate these groups of antennas and waveguides into a diagnostics slim cassette (DSC), which is a dedicated complete poloidal segment specifically designed to be integrated with the water-cooled lithium lead (WCLL) breeding blanket system. This contribution presents the multiple engineering and physics challenges addressed while designing reflectometry diagnostics using radio science techniques. Namely, short-range dedicated radars for plasma position and shape control in future fusion experiments, the advances enabled by the designs for ITER and DEMO, and the future perspectives. One key development is in electronics, aiming at an advanced compact coherent fast frequency sweeping RF back-end [23-100 GHz in few μs] that is being developed at IPFN-IST using commercial Monolithic Microwave Integrated Circuits (MMIC). The compactness of this back-end design is crucial for the successful integration of many measurement channels in the reduced space available in future fusion machines. Prototype tests of these devices are foreseen to be performed in current nuclear fusion machines.

A Low SNR Signal-Sensing Method Based on a Multiple-Antenna Covariance Matrix

In this paper, we propose a promising signal-sensing method based on both single- and multiple-antenna covariance matrices of the received signal. In comparison with microwave diagnostics or energy detection, the proposed method does not need prior information of signal and noise. Therefore, it can be widely used in noise power uncertainty scenarios, such as signal transmission in hypersonic plasma sheath, with symmetry to the signal-sensing method in cognitive radio. Designing an efficient signal-sensing method that supports both the application for the field of hypersonic plasma sheath communication or cognitive radio is still an attractive subject deserving of study in symmetry journals. Theoretical analysis and the implementation algorithm of a single-antenna covariance matrix are carried out for the proposed method, with a possible extension to multiple-antenna situations. Simulations show the proposed method has excellent performance, even for very low signal-noise-ratio (SNR) signals, and is competitive with state-of-the-art algorithms.

Microwave Near-Field Dynamical Tomography of Thorax at Pulmonary and Cardiovascular Activity.

The developed near-field microwave diagnostics of dynamical lung tomography provide information about variations of air and blood content depth structure in the processes of breathing and heart beating that are unattainable for other available methods. The method of dynamical pulse 1D tomography (profiling) is based on solving the corresponding nonlinear ill-posed inverse problem in the extremely complicated case of the strongly absorbing frequency-dispersive layered medium with the dual regularization method-a new Lagrange approach in the theory of ill-posed problems. This method has been realized experimentally by data of bistatic measurements with two electrically small bow-tie antennas that provide a subwavelength resolution. The proposed methods of 3D lung tomography based on the multisensory pulse, multifrequency, or multi-base measurements are based on solving the corresponding integral equations in the Born approximation. The experimental 3D tomography of lung air content was obtained by the results of the multiple 1D pulse profiling by pulse measurements in several grid points over the planar square region of the thorax. Additionally, the possible applicability of multifrequency measurements of scattered harmonic signals in the monitoring of lungs was demonstrated by four-frequency measurements in the process of breathing. The results demonstrated the feasibility of the proposed control in the diagnosis of some lung diseases.

Field and Temperature Shaping for Microwave Hyperthermia: Recent Treatment Planning Tools to Enhance SAR-Based Procedures.

The aim of the article is to provide a summary of the work carried out in the framework of a research project funded by the Italian Ministry of Research. The main goal of the activity was to introduce multiple tools for reliable, affordable, and high-performance microwave hyperthermia for cancer therapy. The proposed methodologies and approaches target microwave diagnostics, accurate in vivo electromagnetic parameters estimation, and improvement in treatment planning using a single device. This article provides an overview of the proposed and tested techniques and shows their complementarity and interconnection. To highlight the approach, we also present a novel combination of specific absorption rate optimization via convex programming with a temperature-based refinement method implemented to mitigate the effect of thermal boundary conditions on the final temperature map. To this purpose, numerical tests were carried out for both simple and anatomically detailed 3D scenarios for the head and neck region. These preliminary results show the potential of the combined technique and improvements in the temperature coverage of the tumor target with respect to the case wherein no refinement is adopted.

Reflectometry diagnostics for atmospheric entry applications: state-of-the-art and new developments

Insight into the plasma properties of high-speed ionized flows is key for the validation of predictive aerothermodynamic tools for atmospheric entry applications, namely plasma radiation which will be highly dependent on the flow electron densities, which accordingly need to be accurately estimated. We performed an extensive review on past re-entry microwave diagnostics, including both in-flight and ground-test experiments. This work assesses the peculiar characteristics of entry plasmas, and derives functional requirements for microwave diagnostics tailored for such applications. A preliminary analysis, including a simulation of electromagnetic environment for the RAM-C II flight experiment, obtained through a CFD code coupled to an electromagnetic propagation code, is presented. The obtained results outline the adequacy of such diagnostics for improving verification and validation for high-speed entry plasma flows.

Parametric Decay Instabilities during Electron Cyclotron Resonance Heating of Fusion Plasmas, Problems and Possibilities

We review parametric decay instabilities (PDIs) expected in connection with electron cyclotron resonance heating (ECRH) of magnetically confined fusion plasmas, with a specific focus on conditions relevant for the ITER tokamak. PDIs involving upper hybrid (UH) waves are likely to occur in O-mode ECRH scenarios at ITER if electron density profiles allowing trapping of UH waves near the ECRH frequency are present. Such PDIs may occur near the plasma center in ITER full-field scenarios heated by 170 GHz O-mode ECRH and on the high-field side of half-field ITER plasmas heated by 110 GHz or 104 GHz O-mode ECRH. Additionally, 110 GHz O-mode ECRH of half-field ITER scenarios may have low ECRH absorption, due to the electron cyclotron resonance being located on the high-field side of the main plasma. This potentially allows PDIs driven by a significant amount of ECRH radiation reaching the UH resonance in X-mode to occur, as X-mode radiation can be generated by reflection of unabsorbed O-mode radiation from the high-field side wall. The occurrence of PDIs during ECRH may damage microwave diagnostics, such as the electron cyclotron emission and low-field side reflectometer systems at ITER, as well as complicate the calculation of heating and current drive characteristics. However, if PDIs are induced in a controlled manner, they may provide novel diagnostic tools and allow the generation of a moderate fast ion population in plasmas heated only by ECRH.

Extending the Functionality of Resonator Aperture Sensors for Microwave Diagnostics of Small-sized Objects

Extending the Functionality of Resonator Aperture Sensors for Microwave Diagnostics of Small-sized Objects

Spectral Intensity of Electron Cyclotron Radiation Emerging from the Plasma to the First Wall in ITER

It is predicted that in ITER, due to high values of electron temperature and magnetic field strength, electron cyclotron (EC) radiation emitted by plasma will be a significant source (together with external EC radiation injected for auxiliary plasma heating and non-inductive current drive) of additional thermal and electromagnetic loads for microwave and optical diagnostics. The spectral distribution of plasma EC radiation is particularly important to consider in millimeter-wave diagnostics, namely for high- and low-magnetic-field side reflectometry, plasma position reflectometry, and collective Thomson scattering diagnostic, because the transmission lines of these diagnostics yield the transport of EC waves emitted by the plasma. The development of semi-analytical methods used to describe the spectral distribution of plasma-generated EC radiation in tokamaks, starting from the work of S. Tamor, is based on the dominance of multiple reflections of this radiation from the first wall in a toroidal axially symmetric vacuum chamber. Here, we present calculations using the CYNEQ code of the spectral intensity of the EC radiation emerging from the plasma to the first wall and port plugs for five scenarios of ITER operation. This code uses the symmetry-based effect of approximate isotropy and homogeneity of radiation intensity in a substantial part of the phase space and has been successfully tested by comparison with first-principles codes. The energy flux density in the range of 30–200 kW/m2 is predicted for wall reflectance in the range of 0.6–0.95. The possible effect of this radiation on in-vessel components and diagnostics is assessed by calculating the surface density of the energy absorbed by various materials of the ITER first wall.