Microstrip Patch Antenna Array Research Articles

Design of higher gain linearly polarized 2×2 microstrip patch array antenna for wireless communication

The fifth-generation technology is popular and best as far as data rates are concerned for wireless applications. To meet the increased demand of the modern world for faithful communication, this research work is carried out. In this approach, a single patch, 1×2 array, and 2×2 array are designed using a low-cost FR4 dielectric substrate ( =4.4) covering the 3.3–3.8 GHz frequency band. Due to the lack of gain from arrays in the present research, an attempt is made to achieve excellent gain from arrays with a minimum number of patches. First, the gain of a single inset-fed antenna is compared with another normal single patch of the same thickness but with an additional air dielectric medium. Next, the second single patch is extended to obtain a rectangular 1×2 array and a 2×2 array antenna. A second single patch measuring 50×32.5×0.8 mm is designed assuming an infinite ground plane. It has 3mm air gap between the patch strip and the ground. Air acts as a second dielectric layer that reduces power loss. This allows a maximum gain of 15.2 dB with a return loss of -22 dB. Also, antenna efficiency and bandwidth are 91% and 267.69 MHz, respectively.

An In-Band Low-Radar Cross Section Microstrip Patch Antenna Based on a Phase Control Metasurface

An in-band low radar cross section (RCS) microstrip patch antenna based on a phase control metasurface is proposed. As the size of the phase control metasurface changes, it will have different phase adjustments to the incident electromagnetic wave. Two kinds of phase control metasurfaces with a 90° reflection phase difference are arranged in a checkerboard configuration and loaded above a microstrip array antenna. The metal of the microstrip array antenna can fully reflect the electromagnetic wave, so the incident wave passes through the metasurface again and forms a reflected wave with a phase difference of 180° ± 37° when passing through the phase control metasurfaces of different sizes. Thus, the microstrip array antenna can achieve in-band RCS reduction. The metamaterial forms a transmission window in the microstrip patch array antenna band to maintain the radiation performance. Finally, a reasonable agreement is obtained between the measured and simulated results.

A simple feed orthogonal excitation X-band dual circular polarized microstrip patch array antenna

This work represents a microstrip patch array antenna which is designed and analyzed for the application of circular polarization in X band frequency range. The proposed antenna array has a very simple microstrip line feeding mechanism and each patch is energized orthogonally to acquire circular polarization without the need for any phase shifters. The array antenna has a slot line in the ground to electrically couple the signals from the microstrip feed line to feed each patch. The outcome demonstrates that the antenna is capable of radiating both left-hand circular polarization (LHCP) and right-hand circular polarization (RHCP). The designed work has a return loss of -41.88 dB, that is the antenna is perfectly matched. The outcome also demonstrates the antenna’s strong gain and directivity capabilities, which are 12.87 dBi and 13.30 dBi, respectively. The antenna resonates circularly at a frequency of 10 GHz.

Phase delay through slot-line beam switching microstrip patch array antenna design for sub-6 GHz 5G band applications

Two, four, eight, and sixteen-element patch array antennas for beam switching are presented in this study. For a 1×2 array, an aperture-coupled feeding mechanism is used to feed patches while a slot line on the ground plane provides the phase delay between antenna elements. The 1×2 array is used to create the 2×2, 4×2, and 8×2 arrays, and an equal power divider provides the signal for each. For applications in the 5G sub-6 GHz frequency spectrum, the antennas are modeled. With -37.14 dB, -17.85 dB, -21.51 dB, and -26.03 dB return loss for two, four, eight, and sixteen-element array antennas respectively the simulation demonstrates that the antennas are properly matched at the resonant frequency. The antennas can switch its radiated beam to ±24<sup>o</sup>, ±24<sup>o</sup>, ±28<sup>o</sup>, and ±26<sup>o</sup> with gains of 8.97 dBi, 11.19 dBi, 13.23 dBi, and 16.24 dBi, respectively at the resonance frequency. The directivity of the proposed antenna is found to be 9.17 dBi, 11.20 dBi, 13.40 dBi, and 16.45 dBi respectively. The antennas are constructed with two 0.8 mm-thick Teflon substrate layers. The ground plane between the two substrate layers contains the aperture and the slot line that generates the phase delay.

A review of beamforming microstrip patch antenna array for future 5G/6G networks

With the increase in demand for high data rates and high bandwidth because of multiple users all over the globe, the technology has moved toward the next-generation of wireless communication. This rapid advancement of wireless communication technologies has led to the emergence of 5G networks, which promise significantly higher data rates, lower latency, and enhanced connectivity. Researchers believe that five essential techniques can enable 5G. Beamforming is one of those essentials, as it plays a vital role in achieving reliable and high-capacity communication. This review article portrays a comprehensive analysis of the 5G beamformer Microstrip Patch Antenna array techniques for communication systems. The paper comprises of a deep overview of the fundamental concepts and principles of beamforming, including analog, hybrid, and digital beamforming techniques. It explores the advantages and disadvantages of each approach and discusses their suitability for 5G applications. An in-depth examination of various beamforming techniques employed in 5G, encompassing traditional beamforming, massive Multiple-Input-Multiple-Output beamforming, hybrid beamforming, and adaptive beamforming. The discussion encompasses the strengths, weaknesses, and performance trade-offs of each technique, along with their applicability in diverse deployment scenarios and applications. The review of multiple couplers that are used for the feeding of the antenna is discussed with included hybrid coupler, Wilkinson power divider, branch line coupler, and butler matrix in beamformer smart antenna for 5G/6G communications. Numerous beamforming techniques are compared based on their merits, demerits, and applications. Moreover, the dielectric substrate utilized to design the beamformer was also reviewed. The findings presented in this paper serve as a valuable resource for the researcher, scholars, and engineers working in the field of 5G wireless communications and antenna designing, facilitating the development and deployment of efficient and robust beamforming solutions for future 5G networks.

Optimization of Antenna Excitations for Non-Invasive Microwave Hyperthermia for Breast Cancer Treatment

This research demonstrates an effective focused microwave hyperthermia for non-invasive breast cancer treatment at early stages where the tumour size is small and has not spread to nearby tissues. First, a three-dimensional (3-D) Micro-Strip Patch (MSP) antenna array consisting of four elements and operating at 2.45GHz is used. Second, two evolutionary optimization techniques, particle swarm optimization (PSO) and genetic algorithm (GA), are compared in terms of optimization speed in order to select the algorithm which will be used in this study to calculate the ideal phase and amplitude excitations for each MSPA. The fitness function of the used algorithm aims to increase the specific absorption rate (SAR) and power density (Q) at the tumour site while keeping these values at minimum levels in healthy positions. The focusing technique is used to collect a data of accurate antenna excitations of a tumour having a radius of 2.5 mm (less than 1 cm3 volume), embedded in every possible position in the glandular tissues in the antenna array's central plane. Using MRI results from a real patient (age 40) in the prone position, a realistic breast model was produced. In order to demonstrate the efficiency of the suggested 3D microwave focusing technology, the temperature distribution at the tumour centre position was measured and compared with other healthy locations. The data gathered are then used to create a non-invasive hyperthermia GUI system for the treatment of breast cancer.

Sidelobe level reduction in pattern synthesis of a non-uniform series-fed microstrip antenna array using the TLBO algorithm

In this paper, a series-fed microstrip patch antenna array with high gain and extremely low sidelobe levels, operating at 24 to 24.25 GHz, is presented. This antenna is fabricated on a single-layer PCB substrate. Due to its features such as compactness, lightweight, low cost, high gain, and narrow beamwidth, it can be used in many applications such as perimeter surveillance and collision-avoiding radar systems. The proposed antenna is a rectangular antenna array that consists of a non-uniform linear array with 50 in-line series-fed elements in one dimension and a uniform linear array with 16 elements in the other dimension. The non-uniform array provides 78% more physical space between the central elements, which is used to place the feed network of the uniform array. The radiation pattern of this non-uniform array has been synthesized using the TLBO algorithm. The prototype antenna with dimensions of 335 mm × 120 mm has been fabricated and tested. The measured gain of this antenna at central frequency is 28 dBi, with a 3-dB beamwidth of 2.6°and 7°and sidelobe level of 23.3 and 22.5 dB in the E-plane and H-plane respectively.

Development of a novel optimization algorithm for a microstrip patch antenna array

<span>Microstrip patch antennas are typically used because they have a low profile and cost. The main theme of this study is to present a novel 2×2 microstrip antenna array design using rough set theory. In designing the 2×2 microstrip antenna array, an FR4 dielectric substrate was used to improve the performance. The rough set theory was used to optimize the microstrip antenna parameters. The FR4 dielectric substrate compared better to the microstrip patch antenna array wherein no substrate was used. The antenna with no substrate used had the energy that is radiating underneath which contributed to the sidelobes of the radiation pattern whereas the use of the substrate reduced the energy radiated at the substrate. Furthermore, the gains of the two were also simultaneously evaluated and it showed that the microstrip antenna array with the dielectric substrate had better gain than the one without. This 2×2 microstrip array antenna design may be used for applications such as mobile communications since it is small in size and performs well.</span>

Design of a 2*2 Microstrip Phased Array Antenna for Radar Applications

Micro-strips patch antennae used in array configurations are more beneficial than single antenna element by augmenting the directivity (dB) radiation pattern, and lowering the substrate's permittivity to overcome its drawbacks, which include poor gain, low efficiency, narrow bandwidth limited directivity. It also facilitates beam-steering capability which is obtained by enabling phase difference(β) between the antennas. Beam scanning capability is used in radar and GNSS technologies. This paper proposes a 2*2 microstrip phased array antenna by using rectangular microstrip patch antenna on an FR-4 dielectric substrate for beam scanning. The resonant frequency of the antenna is at 2.52GHz frequency with a good Voltage Standing Wave Ratio (VSWR) value of 1.1325. The design has been simulated in Ansys HFSS software. The simulation results exhibit antenna better performance of the proposed antenna compared to state-of-art designs present in the literature. The compactly designed Rectangular Micro-strip Patch Antenna array shows a low S-parameter (–24.127858 dB), high gain (13.689104 dB), directivity (14.055125 dB), and efficiency of 91.917%.

Metasurface-based bandwidth and isolation enhancement for compact H-plane coupled antennas

A simple metasurface (MS) composed of a square metal ring and four extended metal strips is designed to simultaneously enhance the bandwidth and isolation of H-plane coupled microstrip patch antenna array in this paper. By adding the MS above the patch array, a new resonance is formed to increase the working bandwidth and the coupling between the antenna array is largely depressed to enhance the isolation property. An antenna array with MS is simulated, fabricated and measured. The simulated and measured results are in good agreements. Measured results indicate that the bandwidth with S 11 ⩽ −10 dB is broadened by 8.1% compared with the original coupled antennas. In addition, within the working band, the isolation level is better than −20 dB, and the maximum mutual coupling reduction reaches 39.6 dB at 5.19 GHz, performing an excellent wideband decoupling effect. Moreover, the proposed method has been extended to large antenna arrays, implying that it can be widely used in multiple-input multiple-output or the wireless Rx/Tx system.

Novel broadband circularly polarized pentagonal printed antenna design for wireless power transmission applications

<p>This paper provides a new conception for a microstrip patch antenna array that operates in a circularly polarized manner for wireless power transmission (WPT) at 2.45 GHz. The proposed conception combines four pentagonal patches and the defected ground structure (DGS) method. The antenna array with a dielectric constant of 4.4 and a tangential loss of 0.025 is printed on a FR4 where its thickness is about 1.58 mm. The developed design aims to optimize the antenna array performance. Th e main contribution, to the telecommunications and WPT fields, is to achieve a maximum energy transfer with low losses, while also ensuring adequate adaptation to the excitation port. To prove the effectiveness of this design, simulation results were obtai ned using computer simulation technology microwave studio (CST MWS) software and validated by another solver high - frequency structure simulator (HFSS). Simulation results are presented and compared with those obtained using existing conceptions in the lite rature. The proposed design has proven to be very effective in achieving the intended objectives, which makes this design very good for radiofrequency (RF) energy collection and its various applications to power a variety of devices without harming our pla net.</p>

Design and simulation of 1 × 2, 1 × 4 and 2 × 8 microstrip patch antenna arrays based on photonic crystals for improved gain performance in THz

Design and simulation of 1 × 2, 1 × 4 and 2 × 8 microstrip patch antenna arrays based on photonic crystals for improved gain performance in THz

Design of proximity‐coupled antenna array for 5G communication

SummaryMicrostrip patch antennas (MPA) are widely used in wireless communication systems due to their ease of manufacture, low cost, and low profile. This work proposes a proximity‐coupled rectangular microstrip patch antenna array (PRMPA) adaptable for 5G applications. However, the existing research works suffered from low gain, low efficiency, and narrow bandwidth. In addition, 5G communications suffer from path loss in high‐frequency bands. For managing this issue, the large gain antenna is essential. Hence, this research aims to design and fabricate high‐gain compact 2 × 2 slotted PRMPA for 5G applications. The antenna design is simulated on HFSS and operates at 28–37 GHz. Here, the antenna parameters like length, width, and feed line parameters are optimized using a metaheuristic optimization like the mayfly optimizer (MFO). Further, a circular‐shaped metamaterial split‐ring resonator (SRR) reduces the mutual coupling. Then, Rogers RT5880 is used as substrate material, and the design operates at 34.5 GHz. The gain and radiation efficiency achieved by the proposed antenna design are 15.4 dB and 94.4% for the simulated outcomes.

Design and Analysis of Microstrip Patch Antenna Array and Electronic Beam Steering Linear Phased Antenna Array with High Directivity for Space Applications.

This study proposes an E-shaped microstrip patch antenna array (MSPAA). The substrate is RT/Duroid5880. Its 2.2 dielectric constant gives it a larger bandwidth than substrate materials with higher dielectric constants. The periphery dimension of a single E patch is 50 × 41 mm2. The areas of 2 × 2 and 3 × 3 MSPAAs are 120 × 96 and 180 × 144 mm2, respectively. Array members are 10 and 7 mm apart horizontally and vertically, respectively. MTM technology builds the projected MSPAA. This work looks at the effects of gain, reflection coefficient (return loss), directivity, bandwidth, and VSWR on proposed 2 × 2 and 3 × 3 MSPAAs with different patch lengths of 30, 40, and 60 mm, patch widths of 40, 50, and 60 mm, and substrate thicknesses of 0.8 and 1.6 mm. Also, this study compares the performance of existing E-shaped MSPAAs with proposed 2 × 2 and 3 × 3 MSPAAs. The suggested MSPAA performs better than the existing E-shaped MSPAA. The series network analyzer measures the prototype MSPAA's experimental outcomes. The polynomial is recommended for estimating the antenna array area with odd and even rows and columns. CST Studio Suite software analyzes and designs antenna arrays, and simulation findings are compared with hardware results. The main benefit of the proposed 2 × 2 MSPAA is that it reduces sidelobes. It has a gain of 8.9 dBi, a directivity of 8.95 dBi, a VSWR of 1.02, a return loss of -32.91 dB, and a bandwidth of 0.1 GHz at both 1.6 and 0.8 mm substrate material thicknesses. Across its operating range of 3.8-4.2 GHz, the recommended array antenna has a radiation gain of 7.01-7.81 dB and an efficiency of 68.51-71.11%. At 4 GHz, this study looks at how electronic steering affects the phase angle of the excitation signal, the number of elements, and the distance between elements in the beam steering linear phased antenna array (BSLPAA) using MATLAB.

Design of a Circular Concentric Microstrip Patch Antenna Array for WI-FI Band Energy Harvesting

Design of a Circular Concentric Microstrip Patch Antenna Array for WI-FI Band Energy Harvesting

Radiation Pattern Synthesis Using Constraint Convex Optimization Algorithm for Conformal Antenna Array

In this paper, a model based on constraint convex optimization is proposed for the radiation pattern synthesis in cylindrical and spherical microstrip conformal array antennas. The optimization algorithm is modeled to decrease the Euclidean distance between the obtained radiation pattern of the deformed array and the desired radiation pattern of the planar array by calculating the suitable amplitude and phase values for the individual array patches. Four prototypes of 2×2, 3×3, 4×4, and 5×5 microstrip patch array antenna are used as the radiating elements which are deformed from planar arrangement and placed on the faces of prescribed spherical and cylindrical shapes with various radii of curvatures. The results reveal that the performance of optimization algorithm performs better in 5×5 array, followed by 4×4 array, 3×3 array, and 2×2 array. However, 5×5 array provides more degrees of freedom for tuning the radiation pattern in desired form. The 5×5 array computes suitable amplitude and phase values for the radiating elements of the array, which restore the radiation pattern in terms of mainlobe reconstruction, null locations, sidelobe levels, up to the deformation of 20 cm in both spherical and cylindrical configurations of conformal array. The proposed optimization technique when applied to conformal antenna array offers fast computational speed and good convergence accuracy for radiation pattern synthesis, which can be useful for various engineering applications.

Wide-Angle Scanning Microstrip Patch Antenna Array for mmWave Applications with High Gain

This paper presents a modified rectangular microstrip patch antenna (MRMPA) array conforming to the hemisphere for wide-angle beam scanning. Two different conformal antenna array designs are presented in this work. The first of these designs, a 13-element MRMPA array conformal to the surface of a circular arc, and the second one, a 9-element array conformal to the surface of a hemisphere, are designed and optimized. The geometrical approach of calculating the phase value is used to calculate the phase value of each antenna. The simulated results show that the 13-element conformal MRMPA array is achieving a beam scanning angle of ±84° with a gain of 13.89 dBi with low side lobe levels, and further, the gain of the array is enhanced by a dielectric superstrate that improved the gain by ∼2 dBi at all the scanning angles. Second, an MRMPA array conformal to a hemisphere with nine elements is designed with beam scanning ability from φ = 0°−360° and θ = ±30° with a gain of 15.69 dBi, and further, the gain is enhanced by ∼3 dBi with the dielectric superstrate. Full-wave simulations have proven both designs to be accurate and aligned with theoretical calculations.

A low sidelobe 77 GHz centre‐fed microstrip patch array antenna

AbstractA low sidelobe 77 GHz centre‐fed microstrip patch array antenna is proposed for automotive radar application. The proposed antenna comprises eight linear antenna arrays, each of which is centre‐fed by a coplanar waveguide with ground transmission line at the back of the microstrip patches. Each linear antenna array contains 10 patch antenna units, which are connected through a T‐type power divider network to achieve a −30 dB Taylor weighted distribution. The simulation results show that the designed phased array antenna has a good one‐dimensional phased scanning ability of ±45° with active voltage standing wave ratio less than 2 at 75–79 GHz, along with −20 dB low sidelobe symmetrical radiation patterns in the H plane. An antenna sample fed by a WR12 waveguide is fabricated and measured to verify its performance. The measured VSWR is less than 2 at 73.6–85 GHz. This design provides a new idea for millimetre wave automotive radar antenna design.

A Dual-Polarized Antenna Array With High Port Isolation Through TM03/04 Modes Cancellation

A new dual-polarized microstrip patch antenna array (MPAA) with high port isolation through TM03/04 modes cancellation is designed and reported in this letter. By introducing branches etched with slots between the units, the resonant frequency and impedance of TM03 mode are adjusted to be consistent with that of TM04 mode. First, TM03/04 modes cancellation decoupling scheme is applied to a two-element MPAA. And then, the proposed decoupling method is expanded to the compact decoupled dual-polarized four-element MPAA through multi-layer distribution. The co-linear port coupling is below -27 dB within the impedance matching bandwidth (S11 < -10 dB from 3.35 to 3.53 GHz), which is reduced by 20 dB from the original coupling. The maximum gain of 6.4 dBi is achieved, and the radiation efficiency is above 80%. Through miniaturized design, the proposed decoupling scheme achieves high port isolation and a stable radiation pattern. The proposed method may be expanded and greatly improve the performance in future decisions.

A High-Gain Dual-Band Multibeam Antenna System for MIMO Wi-Fi Application

A compact dual-band multibeam antenna system with high gain is presented for multiple-input-multiple-output (MIMO) Wi-Fi application. The antenna system is composed of four rotationally symmetric antenna panels occupying a compact size of 60 × 200 × 7.2 mm3. Two series-fed microstrip patch antenna (MPA) arrays are proposed to operate at the 5-GHz band. They are fed with ±90° phase difference signals for two directional radiation patterns with about 45° horizontal 3-dB beamwidth and distinct radiation directions. Two dual-function metasurface based on periodically loaded parallel lines is designed and compactly placed between the two MPA arrays. The metasurface works as a 2.4-GHz antenna with about 90° 3-dB beamwidth in the azimuth. Besides, the application of metasurface improves the gains at the 5-GHz band. Then, four antenna panels are placed in a rotating arrangement with an electric size of 0.59λL × 0.59λL × 1.57λL (λL is the free-space wavelength at the lowest operating frequency). The antenna system was manufactured and demonstrated the characteristics of 360° pattern coverage in azimuth and high gain. The measured average gains are respectively higher than 8 dB and 12 dB at the 2.4-and 5-GHz bands.