Microscopy Techniques Research Articles

Electrolytic synthesis of γ-Al2O3 nanoparticle from aluminum scrap for enhanced methylene blue adsorption: experimental and RSM modeling

The presence of methylene blue (MB) dye in wastewater has raised concern about human health and environmental ecology due to potential carcinogenic, and mutagenic effects. Therefore, this work aims to remove MB dye from wastewater using γ-Al2O3 nanoparticles synthesized from aluminum scrap via simple electrolytic method. The successful synthesis of the adsorbent was confirmed by a range of spectroscopy and microscopy techniques, including XRD, SEM, FTIR, and BET. The central composite design (CCD) of the response surface methodology (RSM) method was used to optimize the processing parameters such as solution pH, contact time, initial MB concentration, and adsorbent dose. The ANOVA results clearly shows that the quadratic model (p < 0.0001) was sufficient to the best predicting of the removal performance of MB dye (R2 = 0.9862). The optimum condition for the maximum MB dye removal (98.91%) was achieved at solution pH of 8.298, initial MB concentration of 31.657 mg/L, adsorbent dose of 0.387 g/L, and contact time of 46.728 min. Nano-γ-Al2O3 was shown to have a good surface area of 59 mg2/g by BET analysis. The adsorption kinetics follows the pseudo-second-order model (R2 = 0.997). With a maximum adsorption capacity of 137.17 mg/g, the Langmuir isotherm model (R2 = 984) provides the best fit to the adsorption isotherm data, indicating a monolayer adsorption process. Furthermore, thermodynamic analysis demonstrated that the adsorption of MB dye was an endothermic and spontaneous process. The reusability study showed that γ-Al2O3 nano-adsorbent retained 85.08% of its original removal efficiency after five cycles. According to the findings of the study, MB dye molecules were taken up by γ-Al2O3 nano-adsorbent via hydrogen bond formation, Van der Waals interaction, and electrostatic attraction. Therefore, γ-Al2O3 nanoparticles can be used as a potentially eco-friendly and low-cost adsorbent for the removal of MB dye from aqueous solutions.

Novel mycophenolic acid precursor-based fluorescent probe for intracellular H2O2 detection in living cells and Daphnia magna and Zebrafish model systems.

Innovative for the scientific community and attracting attention in the extensive biomedical field are novel compact organic chemosensing systems built upon unique core molecular frameworks. These systems may demonstrate customized responses and may be adaptable to analytes, showing promise for potential in vivo applications. Our recent investigation focuses on a precursor of Mycophenolic acid, resulting in the development of LBM (LOD = 13 nM) - a specialized probe selective for H2O2. This paper details the synthesis, characterization, and thorough biological assessments of LBM. Notably, we conducted experiments involving living cells, daphnia, and zebrafish models, utilizing microscopy techniques to determine probe nontoxicity and discern distinct patterns of probe localization. Localization involved the distribution of the probe in the Zebrafish model within the gut, esophagus, and muscles of the antennae.

NG2-Glia Cause Diabetic Blood-Brain Barrier Disruption by Secreting MMP-9.

Disorders of the blood-brain barrier (BBB) arising from diabetes mellitus are closely related to diabetic encephalopathy. Previous research has suggested that neuron-glia antigen 2 (NG2)-glia plays a key role in maintaining the integrity of the BBB. However, the mechanism by which NG2-glia regulates the diabetic BBB remains unclear. Type 2 diabetes mellitus (T2DM) db/db mice and db/m mice were used. Evans-Blue BBB permeability tests and transmission electron microscopy techniques were applied. Tight junction proteins were assessed by immunofluorescence and transmission electron microscopy. NG2-glia number and signaling pathways were evaluated by immunofluorescence. Detection of matrix metalloproteinase-9 (MMP-9) in serum was performed using enzyme-linked immunosorbent assay (ELISA). In T2DM db/db mice, BBB permeability in the hippocampus significantly increased from 16 weeks of age, and the structure of tight junction proteins changed. The number of NG2-glia in the hippocampus of db/db mice increased around microvessels from 12 weeks of age. Concurrently, the expression of MMP-9 increased in the hippocampus with no change in serum. Sixteen- week-old db/db mice showed activation of the Wnt/β-catenin signaling in hippocampal NG2-glia. Treatment with XAV-939 improved structural and functional changes in the hippocampal BBB and reduced MMP-9 secretion by hippocampal NG2-glia in db/db mice. It was also found that the upregulation of β-catenin protein in NG2-glia in the hippocampus of 16-week-old db/db mice was significantly alleviated by treatment with XAV-939. The results indicate that NG2-glia can lead to structural and functional disruption of the diabetic BBB by activating Wnt/β-catenin signaling, upregulating MMP-9, and degrading tight junction proteins.

Morpho-anatomical studies of family lamiaceae species of district Lahore, Punjab: a revision to flora of Pakistan

BackgroundThis study was aimed to determine the taxonomic position and delimitation of fifteen Lamiaceae taxa using leaf epidermal morpho-anatomical features in Lahore. A main objective of the study was also the revision and upgradation of Lamiaceae taxa in the flora of Pakistan, as no details of studied species are found in the flora of Pakistan.MethodsThe examination of significant anatomical parameters, such as epidermal cell shape and size, stomatal types, guard and subsidiary cells shape and size, stomatal cavity size, trichome size and shape, oil droplets, crystals, and secretory cavity characteristics were studied using light microscopic (LM) and scanning electron microscopic (SEM) techniques. Among all the studied Lamiaceae species, these anatomical features varied significantly. Principal component analysis and correlation were done to distinguish the species’ similarities.ResultsMost species had pentagonal and hexagonal epidermal cells with straight anticlinal wall thickness. On the adaxial surface, paracytic stomata were found in Ocimum basilicum L. and Rosmarinus officinalis L. Diacytic stomata was observed in Ajuga reptans L. and anisocytic stomata in Galeopsis tetrahit L. In the abaxial surface, trichomes were present in five species, i.e., Mentha suaveolens Ehrh. A. reptans, Thymus vulgaris L., M. haplocalyx, and Salvia splendens Ewat. In S. splendens, peltate and glandular trichomes were seen whereas, in other species, trichomes were long, unbranched glandular and had tapering ends. In adaxial side trichomes were present only in M. suaveolens, A. reptans, S. bazyntina, O. basciculum, S. splendens, S. officinalis, S. rosemarinus. In other species, trichomes were absent on the adaxial surface. In abaxial view, M. suaveolens had the largest length of trichomes, and O. basciculum had the smallest. S. splendens L. had the largest trichome width, while T. vulgaris had the smallest.ConclusionHence, according to these findings, morpho-anatomical traits are useful for identifying Lamiaceae taxa. Also, there is a need of upgradation and addition of studied taxa in flora of Pakistan comprehensively.

The evolution of organic material on Asteroid 162173 Ryugu and its delivery to Earth

The recent return of samples from asteroid 162173 Ryugu provides a first insight into early Solar System prebiotic evolution from known planetary bodies. Ryugu’s samples are CI chondrite-like, rich in water and organic material, and primarily composed of phyllosilicate. This phyllosilicate surrounds micron to submicron macromolecular organic particles known as insoluble organic matter. Using advanced microscopy techniques on Hayabusa-2 samples, we find that aqueous alteration on Ryugu produced organic particles richer in aromatics compared to less altered carbonaceous chondrites. This challenges the view that aromatic-rich organic matter formed pre-accretion. Additionally, widespread diffuse organic material occurs in phyllosilicate more aliphatic-, carboxylic-rich, and aromatic-poor than the discrete organic particles, likely preserving the soluble organic material. Some organic particles evolved to encapsulate phyllosilicate, indicating that aqueous alteration on Ryugu led to the containment of soluble organic matter within these particles. Earth therefore has been, and continues to be, delivered micron-sized polymeric organic objects containing biologically relevant molecules.

Stereoscopic Microscopy of Snow Crystals

Abstract Snow crystals (snowflakes) are composed of an enormous diversity of shapes that have attracted significant scientific attention over the past decades. Under the microscope, these natural structures are frequently characterized by high complexity, the detailed exploration of which requires the use of enhanced magnifications. In the work presented here, an insight into the microcosm of snow crystals is presented by application of specific light microscopy techniques. Micrographs were produced by means of a low-temperature (LT) device that prevented premature melting of the structures. Additionally, single crystals were imaged as to a stereoscopic visualization allowing the detailed spatial investigation of specific structural elements.

Synthesis, characterization, and a comparative study on the catalytic activity of the functionalized magnetic nanoparticles for the green oxidation of sulfides

AbstractIn the following research, meso‐tetrakis(4‐carboxyphenyl)porphyrinatomanganese (III) acetate (MnTCPP(OAc)) was immobilized onto the surface of two functionalized magnetic nanoparticles (MNPs) with different linker length via amide bond (Fe3O4@SiO2‐NH2‐MnTCPP(OAc) (A1) and Fe3O4@SiO2‐NHCO‐NH2‐MnTCPP(OAc) (A2)). The prepared catalysts were characterized by standard methods such as: atomic absorption spectroscopy (AAS), Ultra violet‐visible (UV‐Vis), Fourier‐transform infrared (FT‐IR), vibrating sample magnetometry (VSM), field emission scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) techniques and also the effect of the length of the linker on the catalytic activity of supported magnetic nanohybrids was investigated. The prepared magnetic nano‐catalysts with different linker lengths were participated in a comparative study of the clean oxidation of sulfides with urea hydrogen peroxide (UHP) in ethanol. The higher catalytic activity, selectivity and also reusability were achieved in the presence of the catalyst with longer linker length (A2) at ambient temperature. Moreover, the turnover number (TON) of catalytic reactions using A2 as catalyst was highly enough to consider the catalyst as an efficient material to oxidize various sulfides. Both A1 and A2 catalysts simply have accomplished 5 runs of recycling without significant decrease in the catalytic activity.

Unraveling the mystery of sandwich structure: Emerging photocatalytic hydrogen production by g-C3N5 coupled Nb2C MXene forming Schottky heterojunction

The development of new photocatalysts and photocatalytic systems is the essence of the development of photocatalytic hydrogen production engineering. Nitrogen-rich graphite carbon nitride (g-C3N5) has gradually replaced conventional graphite phase carbon nitride (g-C3N4) with a smaller bandgap and high-efficiency visible light utilization. In this study, g-C3N5 and Nb2C MXene coupled composition with sandwich structure were manufactured by a simple ultrasonic magnetic stirring method and used for photocatalytic hydrogen production. By adjusting the ratios of single components in the system, the hydrogen production rate of the optimal sample 4:1g-C3N5/Nb2C under visible light irradiation is 2529.5 μmol·g−1·h−1, which is 21 times higher than that of g-C3N5. The high apparent quantum yield (AQY) value of 17.3 % also proves a high light utilization rate. The atomic force microscopy (AFM) technique reveals variations in the thickness of the samples, while strongly demonstrating the formation of sandwich structure. In addition, X-ray photoelectron spectroscopy (XPS) analysis further reveals the electron transfer paths within the system, preliminarily verifying the formation of Schottky heterojunctions. Kelvin probe force microscopy (KPFM) tests not only re-validate the correctness of the electron transfer path but also demonstrate the accuracy of the energy bands. The density-functional theory (DFT) calculations corroborate that Nb2C MXene plays the role of a photoco-catalyst to form Schottky heterojunctions with g-C3N5 for efficient carrier separation and migration. This work highlights the key role of sandwich structure photocatalytic systems on photocatalytic performance.

Improvement of microbial alkalinity resistance in self-healing cementitious materials by means of gradient domestication

The harsh environment of high alkalinity inhibits the effective induction of calcium carbonate precipitation by microorganisms within concrete. In this study, a gradient domestication method was employed to enhance the alkali tolerance of Sporosarcina pasteurii, and various activity parameters (OD600, conductivity, urease activity, and calcium carbonate content) were assessed in an alkaline cultivation setting. Subsequently, a comprehensive evaluation was conducted to compare the impact of domesticated microorganisms on the mechanical properties, impermeability, and self-healing capacity of concrete. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques were employed to characterize the morphology and composition of mineralization products. The results demonstrate that gradient domestication techniques effectively enhance the activity of microorganisms in highly alkaline environments and confirmed that enhanced alkalinity tolerance possesses the potential for multigenerational retention. In comparison to the undomesticated microbial samples at 28 d, concrete incorporating domesticated microorganisms exhibited a 16.59 % increase in compressive strength, a 37.74 % reduction in sorption, and a 23.08 % decrease in permeability. Additionally, the maximum closed crack width measured 0.57 mm, exceeding the 0.44 mm observed in the non-domesticated bacterial group. This study offers a promising strategy for improving the efficiency of microbial-induced calcium carbonate precipitation in concrete.

Enhancement mechanism of microbial mineralization modified coal gangue aggregate properties

Preparing concrete with coal gangue as the aggregate has significant environmental and economic advantages. Nevertheless, the fundamental characteristics of the manufactured concrete are significantly impacted by the high water absorption and low strength of coal gangue aggregate. The present study employs the microbial-induced carbonate precipitation (MICP) technique to efficiently enhance the characteristics of coal gangue aggregate (CGA). Starting from the circumstances of microbial mineralization, the effects of pH, temperature, and time on the capacity of bacteria for mineralization were taken into consideration. Following solution immersion treatment with varying concentrations of urea, calcium ions, and bacterial solution, the patterns of water absorption, crushing index, apparent density, and ultrasonic pulse resistance of CGA were examined. The precipitates produced by microbial mineralization, the micro-morphology, and the pore structure of the aggregate surface were all characterized, and the mechanism of the modification of CGA by MICP was revealed through the use of scanning electron microscopy (SEM), X-ray diffractometer (XRD), and nuclear magnetic resonance (NMR) techniques. Investigations were also conducted on the mechanical characteristics of modified coal gangue aggregate concrete. The results showed that the water absorption and crushing index of the CGA with optimal modification effect (M-CGA) decreased by 18.5 % and 24.1 %, respectively, which was attributed to the fact that the calcium carbonate formed in the cracks and pores of the CGA filled the aggregates and prevented the penetration of water. The 28-day compressive strength, split tensile strength, and flexural strength of modified coal gangue aggregate concrete prepared from M-CGA were increased by 8.13 %, 13.88 %, and 8.53 %, respectively. MICP is an effective method to improve the properties of CGA, which is conducive to the waste recycling of coal gangue.

Experimental study on impact behaviour of normal strength mortar at cryogenic temperatures and after freeze-thaw cycles

Concrete structures employed for the storage of Liquefied Natural Gases (LNG) currently undergo temperature as low as −170 °C. These critical engineering structures may also experience dynamic loads such as impact or explosion during service life. Therefore, it is crucial to explore the mechanical response of concrete at intermediate to high strain rates together with low temperatures or cryogenic freeze-thaw (FT) cycles. This study presents experimental research into the combined effects of low temperatures and strain rate on normal strength mortar, providing a preliminary analysis of the dynamic performance of concrete at low and cryogenic temperatures. A Split Hopkinson Pressure Bar (SHPB) device was used to investigate the characteristics of dynamic compression (at strain rates of 40, 80, 120 and 160 s−1) and dynamic split tension (at strain rates of 20, 40, 60 and 80 s−1) of Normal Strength Mortar (NSM) at different low temperatures. In addition, the dynamic compression (at strain rates of 80, 130 and 180 s−1) after cryogenic FT cycles was also explored. The findings revealed that the failure pattern of NSM samples exposed to coupled low temperature or cryogenic FT cycles and high strain rate loading notably varied from that observed under room temperature condition. Both the dynamic compressive and split tensile strengths of NSM increased with the strain rates at all temperatures. At −160 °C, the dynamic compressive and splitting tensile strengths of NSM specimens were greater than those at room temperature (by 10.94 % and 28.29 %, respectively) and −70 °C (by 3.13 % and 4.12 %, respectively). Cryogenic freeze-thaw cycles evidently impacted the material static and dynamic performance. An empirical model was developed to predict the dynamic increase factors (DIFs) for both dynamic compression and splitting tensile strengths of NSM at low/cryogenic temperatures and after freeze-thaw cycles. Scanning electron microscopy (SEM) technique was performed to study and comprehend the microscopic processes and microstructural changes after FT cycles.

Clustering Methods for the Characterization of Synchrotron Radiation X‐Ray Fluorescence Images of Human Carotid Atherosclerotic Plaque

This study employs computational algorithms to automatically identify and classify features in X‐Ray fluorescence (XRF) microscopy images. Principal component analysis (PCA) and unsupervised machine learning algorithms, such as Gaussian mixture (GM) clustering, are implemented to label features on a collection of XRF maps of human atherosclerotic plaque samples. The investigation involves the hard X‐Ray nanoprobe (NanoMAX) at MAX IV synchrotron radiation facility, utilizing scanning transmission X‐Ray microscopy (STXM) and XRF techniques. The analysis covers regions of interest scanned by the beam with a step size of 200 nm, yielding XRF maps of elements like calcium, iron, and zinc. These maps reveal intricate structures unsuitable for manual labeling. However, they can be accurately classified in an automated fashion using GM. Prior to clustering, PCA is used to deal with repeated patterns and background areas. The resulting clusters are associated with different types of features, which can be identified as specific tissues confirmed by histology. Regions of high concentrations of phosphorus, sulfur, calcium, and iron are found in the samples. These regions are also observed in the STXM results as spots of low transmission that typically are associated with calcium deposits only.

A review on microfiltration membranes: fabrication, physical morphology, and fouling characterization techniques

Microfiltration is a commonly used pressure-driven membrane separation process for various applications. Depending on the manufacturing method, either tortuous or capillary pore structures are obtained. The structure plays an important role in controlling flux, selectivity, but most importantly, the fouling tendency of the membrane. This review attempts to cover past and current developments in physical morphology and fouling characterization methods, along with the manufacturing methods for microfiltration membranes. The limitations and advantages of direct microscopic techniques and gas-liquid displacement as an indirect method are discussed for physical characterization. Additionally, the current state of the art and technical challenges for various in-situ and ex-situ fouling characterization techniques are also discussed. Finally, some directions for future research are outlined.

Spatial Organization of Lipid Nanoparticle siRNA Delivery Systems Revealed by an Integrated Magnetic Resonance Approach.

Lipid nanoparticles (LNPs) are increasingly finding applications in targeted drug delivery, including for subcutaneous, intravenous, inhalation, and vaccine administration. While a variety of microscopy techniques are widely used for LNP characterization, their resolution does not allow for characterization of the spatial organization of different components, such as the excipients, targeting agents, or even the active ingredient. Herein, an approach is presented to probe the spatial organization of individual constituent groups of LNPs used for siRNA-based drug delivery, currently in clinical trials, by multinuclear solid-state magic-angle-spinning nuclear magnetic resonance (MAS NMR) spectroscopy. Dynamic nuclear polarization is exploited (DNP) for sensitivity enhancement, together with judicious 2H labeing, to detect functionally important LNP constituents, the siRNA and the targeting agent (<1-2 w/v%), respectively, and achieve a structural model of the LNP locating the siRNA in the core, the targeting agent below the surface, and the sugars above the lipid bilayer at the surface. The integrated approach presented here is applicable for structural analysis of LNPs and can be extended more generally to other multi-component biological formulations.

Multiscale Materials Engineering via Self-Assembly of Pentapeptide Derivatives from SARS CoV E Protein.

Short peptide-based supramolecular hydrogels hold enormous potential for a wide range of applications. However, the gelation of these systems is very challenging to control. Minor changes in the peptide sequence can significantly influence the self-assembly mechanism and thereby the gelation propensity. The involvement of SARS CoV E protein in the assembly and release of the virus suggests that it may have inherent self-assembling properties that can contribute to the development of hydrogels. Here, three pentapeptide sequences derived from C-terminal of SARS CoV E protein are explored with same amino acid residues but different sequence distributions and discovered a drastic difference in the gelation propensity. By combining spectroscopic and microscopic techniques, the relationship between peptide sequence arrangement and molecular assembly structure are demonstrated, and how these influence the mechanical properties of the hydrogel. The present study expands the variety of secondary structures for generating supramolecular hydrogels by introducing the 310-helix as the primary building block for gelation, facilitated by a water-mediated structural transition into β-sheet conformation. Moreover, these Fmoc-modified pentapeptide hydrogels/supramolecular assemblies with tunable morphology and mechanical properties are suitable for tissue engineering, injectable delivery, and 3D bio-printing applications.

Light Conversion by Electrochemiluminescence at Semiconductor Surfaces.

ConspectusElectrochemiluminescence (ECL) is the electrochemical generation of light. It involves an interfacial charge transfer that produces the excited state of a luminophore at the electrode surface. ECL is a powerful readout method that is widely employed for immunoassays and clinical diagnostics and is progressively evolving into a microscopy technique. On the other hand, photoelectrochemistry at illuminated semiconductors is a field of research that deals with the transfer of photogenerated charge carriers at the solid-liquid interface. This concept offers several advantages such as a considerable lowering of the onset potential required for triggering an electrochemical reaction as well as light addressable chemistry, via the spatial confinement of redox reactions at locally illuminated semiconductor electrodes. The combination of ECL with photoelectrochemistry at illuminated semiconductors is termed photoinduced ECL (PECL). It deals with the triggering of an ECL reaction through the transfer of photogenerated minority charge carriers at the illuminated solid/liquid interface. PECL results in the conversion of incident photons (λexc), that are absorbed by the semiconductor photoelectrode to emitted photons (λPECL), produced by the ECL reaction. Although demonstrated in the 1970s by Bard et al. in ultradry organic solvents, PECL remained unexplored until the last five years. Nowadays, as a result of the considerable progress achieved in semiconductor photoelectrodes and ECL systems, a large variety of PECL systems can be designed by combining photoelectrode materials with ECL luminophores, making it a versatile tool for light conversion in aqueous media.In this Account, we introduce the fundamentals of ECL and photoelectrochemistry at illuminated semiconductors and review the recent developments in PECL. We discuss the two main PECL light conversion schemes: downconversion (where λexc < λPECL) and upconversion (where λexc > λPECL). Besides, PECL can be used to simplify considerably the common electrochemical setups employed for ECL. Indeed, by engineering the photoelectrode material and carefully considering the reactivity involved for ECL and its counter-reaction, PECL enables the ultimate concept of all-optical ECL (AO-ECL), i.e., ECL generation at an illuminated monolithic device immersed into the electrolyte solution. As discussed in this Account, AO-ECL is an important breakthrough that allows the simplest ECL experimental configuration ever reported, eliminating constraints such as an electrical power supply, wires, electrodes, connections, and specific electrochemical knowledge. As shown at the end of this Account, due to the robustness of recently manufactured PECL systems, several applications can already be envisioned for microscopy, elucidation of solar conversion mechanisms, near-infrared imaging, and bioanalysis.

Molecular evaluation of Eimeria spp. Infection in the Volga-Ural Saiga antelope population of the Republic of Kazakhstan

Saiga antelope (Saiga tatarica) is a protected species in Kazakhstan. Little is known about the parasitofauna of these mammals. Therefore, the focus of this study was to evaluate the prevalence and species diversity of Eimeria spp. infection in the Volga-Ural Saiga antelope population. In June 2023, 104 Saiga antelope fecal samples collected from the district of Zhanibek, located in the province of West Kazakhstan were evaluated using microscopic and molecular techniques. Based on coprovoscopy results, Eimeria spp. Oocysts were present in 22 samples (21%). The four fecal samples containing the largest numbers of Eimeria spp. Oocysts per 10x field were selected for further genetic analysis. DNA extraction, nested PCR amplification, and sequencing were performed on 91 clones, with 80 clones forming a distinct clade and exhibiting genetic similarity to MT801034 Eimeria sp. Voucher HY3. These clones possibly represent an Eimeria specific to Saiga antelopes and gazelle that has previously been morphologically described as Eimeria elegans (Svanbaev, 1979), underscoring the importance of further research into parasitic infections in this protected species.

On the properties of ZnO nanorods (ZnO NRs)/NiO heterostructure prepared by double chemical bath deposition

Abstract We report on the ZnONRs and ZnONRs/NiO heterostructure synthesized by the chemical bath deposition technique. The samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy, Raman spectroscopy, and UV-VIS spectroscopy techniques. XRD, Raman spectroscopy, and SEM analysis revealed the formation of ZnONRs/NiO heterostructure. Raman spectra showed a decrease in intensity of low-frequency non-polar and active (E2 (low)) vibrational mode when NiO is deposited onto ZnONRs. The PL spectra revealed ultraviolet and visible emission bands, whose intensities decreased when NiO grew onto ZnONRs. The Au/NiO/ZnONRs/FTO heterostructure Schottky diode performed better than the Au/ZnONRs/FTO Schottky diode. The Au/NiO/ZnONRs/FTO heterojunction demonstrated a current rectification ratio of 3.03 × 102 at ±2 V and a forward current of 1.51 × 10-3 A, which is higher than that of Au/ZnONRs/FTO having a rectification ratio of 6.79 × 101 at ±2 V and a forward current of 1.651 × 10-5 A.

High-Speed Imaging and Quantitative Analysis of Non-Equilibrium Stochastic Processes Using Atomic-Resolution Electron Microscopy

Abstract Chemical phenomena are inherently complex and stochastic, making them difficult to fully understand using conventional ensemble-averaged analytical methods. These methods primarily capture long-lived species and common structural features, limiting the study of transient intermediates and minute structural characteristics. In contrast, single-molecule time-resolved analysis using advanced microscopy techniques, particularly transmission electron microscopy (TEM), offers high spatial and temporal resolution to observe the nonequilibrium dynamics of molecules and their assemblies. This account discusses the authors’ research on developing TEM techniques to visualize intricate and transient interactions within molecular systems, enhancing the understanding of chemical phenomena at atomic and molecular levels.

Unravelling heterogeneous malaria transmission dynamics in the Peruvian Amazon: insights from a cross-sectional survey

BackgroundMalaria remains a global health challenge, particularly in Peru's Loreto region. Despite ongoing efforts, high infection rates and asymptomatic cases perpetuate transmission. The Peruvian Ministry of Health’s “Zero Malaria Plan” targets elimination. This novel study combines microscopic, molecular, and serological techniques to assess transmission intensity, identify epidemiological risk factors, and characterize species-specific patterns across villages. The findings aim to inform targeted interventions and support broader malaria elimination efforts in line with the Zero Malaria Plan initiative.MethodsA cross-sectional malaria survey was conducted in the Zungarococha community, comprising the villages Llanchama (LL), Ninarumi (NI), Puerto Almendra (PA), and Zungarococha (ZG), using microscopic, molecular, and serological techniques to evaluate malaria transmission intensity. Statistical analysis, including multivariate-adjusted analysis, seroprevalence curves, and spatial clustering analysis, were performed to assess malaria prevalence, exposure, and risk factors.ResultsThe survey revealed a high prevalence of asymptomatic infections (6% by microscopy and 18% by PCR), indicating that molecular methods are more sensitive for detecting asymptomatic infections. Seroprevalence varied significantly between villages, reflecting the heterogeneous malaria transmission dynamics. Multivariate analysis identified age, village, and limited bed net use as significant risk factors for malaria infection and species-specific exposure. Seroprevalence curves demonstrated community-specific patterns, with Llanchama and Puerto Almendra showing the highest seroconversion rates for both Plasmodium species.ConclusionsThe study highlights the diverse nature of malaria transmission in the Loreto region, particularly nothing the pronounced heterogeneity as transmission rates decline, especially in residual malaria scenarios. The use of molecular and serological techniques enhances the detection of current infections and past exposure, aiding in the identification of epidemiological risk factors. These findings underscore the importance of using molecular and serological tools to characterize malaria transmission patterns in low-endemic areas, which is crucial for planning and implementing targeted interventions and elimination strategies. This is particularly relevant for initiatives like the Zero Malaria Plan in the Peruvian Amazon.