Microplastics In Marine Sediments Research Articles

Identification and quantification of polystyrene microplastics in marine sediments facing a river mouth through NMR spectroscopy

Accurate identification and quantification of microplastic pollution in marine sediments are crucial for assessing their ecological impact. In this study, we explored the potential of Nuclear Magnetic Resonance (NMR) spectroscopy as an analytical tool for the analysis of microplastics in complex environmental matrices such as marine sediments. Two common plastic polymers, polystyrene (PS) and acrylonitrile butadiene styrene (ABS), were investigated. The marine sediments facing the Tiber River mouth (Italy) were collected according to a bathymetric gradient. Results demonstrated the successful detection and quantification of PS in all sediment samples (within a range of 12.3–64.6 μg/L), while no ABS significant signals were found. An increment trend with depth was observed in the PS signal, relatable to its physicochemical properties and the Tiber River plume hydrodynamic characteristics. The NMR's non-destructive nature and minimal sample preparation represent a promising avenue for standardizing protocols to assess the microplastic distribution and impact in marine sediments.

Microplastics in Marine Sediments from Dar es Salaam Coast: Spatial Distribution and Characterization

The purpose of the research was to determine the spatial distribution and characterization of microplastics in marine sediments of beaches along the Indian Ocean of Dar es Salaam coast. The sediment samples were extracted in triplicate using floatation method followed by digestion of organic debris, then analyzed using At-FTIR spectrophotometer and stereomicroscope. The mean concentrations of microplastics for Kijichi Beach were 700 ± 907 particles/m2 at 1 cm, 859 ± 839 particles/m2 at 5 cm and 590 ± 782 particles/m2 at 10 cm; from Palm Beach were 157 ± 15 particles/m2 at 1 cm, 130 ± 182 particles/m2 at 5 cm and 16 ± 0 particles/m2 at 10 cm; from Coco Beach were 167 ± 155 particles/m2 at 1cm, 104 ± 100 particles/m2 at 5 cm, 70 ± 86 particles/m2 at 10 cm; from Mbezi Beach were 115 ± 108 particles/m2 at 1cm, 74 ± 82 particles/m2 at 5 cm and 16 ± 0 particles/m2 at 10 cm. The microplastics were polypropylene, polyethylene, polyurethane, polyamide, polyvinyl chloride, polyethylene terephthalate, and polytetrafluoroethylene, in the form of fibres, fragments, sponges and pellets. The sediments were confirmed to be contaminated with microplastics with high amount at 1 cm compared to other profile location.

An Analysis of Microplastics Ingested by the Mediterranean Detritivore Holothuria tubulosa (Echinodermata: Holothuroidea) Sheds Light on Patterns of Contaminant Distribution in Different Marine Areas

Microplastic pollution constitutes a serious environmental problem that requires more effective scientific research to describe its potential impacts on marine fauna. The interaction between microplastics and marine biota can have significant negative effects through the trophic chain, up to human health. To date, several steps forward have been made in our understanding of this phenomenon; however, large knowledge gaps still exist for several taxa and areas. In particular, the pattern of spatial and temporal distribution of microplastics in marine sediments and their interaction with benthic detritivore species still needs to be addressed. The Mediterranean Sea is one of the most impacted areas of the world, and its biota is deeply affected by microplastic pollution. To investigate the effects of the presence of microplastics in the sediments in this area, the echinoderm Holothuria tubulosa was chosen as a model species, and specimens were collected along the Salento peninsula in Apulia, Southern Italy. This peculiar geographic area extends between two ecoregions of the Mediterranean Sea, the Northern Ionian and the Southern Adriatic seas, characterized by peculiar and distinct currents and submarine topologies, resulting in a complex and dynamic ecosystem affected by seasonal fluctuations that make the Salento peninsula an interesting natural laboratory for predictions of future dispersion events on a wider scale. Microplastics were analyzed by investigating the gut contents of H. tubulosa individuals, and the SEM/EDX method was used to confirm the plastic material extracted. Results revealed microplastics in all the specimens analyzed and with a homogeneous pattern of distribution in time and some differences in space, suggesting that the presence of this anthropogenic material is constant throughout the year and its quantity is only slightly affected by the level of conservation and management strategies characterizing the sampling sites.

Microplastics in Marine Sediments in Eastern Guangdong in the South China Sea: Factors Influencing the Seasonal and Spatial Variations

Little is known about the comprehensive factors influencing temporal changes in microplastic abundance in marine ecosystems. We investigated seasonal variations in the microplastic distribution in marine sediments in multiple-used zones of Eastern Guangdong in the South China Sea. The top 10 cm sediments from 26 sites were collected by grab sampling in the spring, summer, and winter of 2021. Marine sediments had the lowest microplastic abundance in summer, significantly lower than in other seasons. The size of microplastics varied from 22.5 to 4363.3 µm but the 50–200 µm range was the most abundant. Transparent and fragmented microplastics were the most frequently observed composition. Microplastic abundance negatively correlated to distance to the coast. However, seaweed ecosystems impacted microplastic abundance by changing the microenvironment and/or direct contact and entrapment. Microplastic abundance is closely related to coastal mariculture and local residential and industrial activities. Polypropylene, polypropylene-polyethylene copolymer, polyethylene terephthalate, and polyethylene were the most frequently detected compositions, probably from packaging materials, textiles, and electronic/electrical/building industries. This work helps to understand the role of multiple-used zones and their influence on microplastic distributions in marine ecosystems. Appropriate management of the use and disposal of plastic waste on land was recommended to alleviate microplastic pollution in the marine environment.

A monitoring and data analysis method for microplastics in marine sediments

In Europe, policy frameworks demand the monitoring of microplastics in marine sediments. Here we provide a monitoring and data analysis method for microplastic particles designed to be used in the context of Marine Strategy Framework Directive (MSFD) and OSPAR policy frameworks. Microplastics were analysed in marine sediments at four different locations in Dutch coastal and transitional waters using replicate sampling to investigate micro-spatial variation. Particle size distribution followed a power law with slope 3.76. Thirteen polymers were identified, with their composition varying between sediments near densely populated West coast areas versus the more rural Wadden Sea area. We quantify differences in the micro-spatial variation of microplastic concentrations between locations using the relative standard error of the mean (RSEM). This metric provides an opportunity to optimize the sensitivity of trend detection in microplastic monitoring networks by selecting locations with relatively low micro-spatial variation. We provide a method to optimize the number of replicate samples for a given location using its relationship with the RSEM. Two replicate samples appear to be cost-effective for relatively homogenous locations, whereas more heterogenous locations require four replicates.

Abundance, morphology, and spatio-temporal variation of microplastics at the beaches of Mumbai, India

Microplastics are a class of emerging pollutants ubiquitously found in the marine environment worldwide. Understanding the extent and nature of microplastics pollution in various coastal environments is important to propose any remediation measures. This study is attempted to explore the extent of microplastics (MPs) contamination in the sediments and water columns of three selected beaches (i.e., Aksa, Versova, and Girgaon Chowpatty) of Mumbai, one of the most populated cities of India, giving insights regarding the morphological characteristics, and spatio-temporal variation. The higher MPs contamination was observed during summer in all beaches. Spatial variation was also observed in this study with higher abundance in Versova and Girgaon Chowpatty beaches compared to Aksa beach. The mean value of MPs in marine sediments and seawater column were 204 ± 110 particles kg −1 and 103 ± 60 particles L−1 respectively. Beads were the most predominant types of MPs, while fibres were the least contributory in both the sediments and seawater column. Most of the observed particles lied in the size range between 0.45 to 500μm. This observed trend of abundance of smaller size fraction suggests the possibility of potential threat to aquatic organisms.

Can leachates of environmentally relevant concentrations of microplastics in marine sediments affect the reproduction of an epibenthic copepod?

Most studies on the effects of microplastics on marine biota are carried out using unrealistically high concentrations. Moreover, although microplastics are capable of carrying toxic substances and thus can cause adverse effects even without coming into direct contact with organisms, little is known about the effects of not accessible for ingestion microplastics on benthic biota. Considering that the presence of microplastic particles can itself cause effects to the biota due to toxic substances leached, the present study evaluated the ecotoxicological effects of microplastic leachates of virgin and beach stranded in marine sediments (whole sediments and elutriates) on the epibenthic copepod Nitokra sp. (size 3 ± 1 mm). Effects on reproduction were evaluated using clean sediment enriched with environmentally relevant concentrations [1 pellet: 46.67g sediment (Low) and 1 pellet: 1.67g sediment (High)] of two types of plastic pellets (size 4 ± 1 mm) (i) virgin (obtained from the manufacturer) or (ii) stranded (collected from Santos beach, São Paulo, Brazil, a highly urbanized beach). The results of the present study showed that microplastics leachate (virgin or from the environment) did not cause an inhibiting effect on reproduction in Nitokra sp. in any of the scenarios tested. These results contribute to further risk assessments of plastic particles for marine biota.

Distribution and characterization of microplastics in marine sediments from the Montenegrin coast.

PurposePlastic pollution in the world has led to an abundance of microplastics (MPs) and has been identified as a potential factor that can lead to serious environmental problems, especially in oceans and seas. Information on the current status of MPs pollution along the Montenegrin coast is insufficiently investigated. This study monitors the abundance, distribution, and sources of MPs, and identifies present polymers in the surface sediment of the Montenegrin coast, as well as comparison with previous research.Materials and methodsTen sampling sites along the Montenegrin coast were selected to collect surface sediment samples. The upper layer of sediment (0–5 cm) was collected by a Petite ponar grab. The samples were dried, and density separation was performed using a NaCl solution. The abundance and morphological characteristics of MPs were determined using an optical microscope (DP-Soft software), while FT-IR analysis was done to identify the polymer type.Results and discussionMicroplastics were identified in all sediment samples with an average abundance of 307 ± 133 (SD) MPs/kg in dry sediment. The highest abundance of MPs was found in locations in the vicinity of highly populated areas, near wastewater discharges, and areas with high fishing and tourist activities. The most dominant shape types of MPs in all samples were filaments and fragments. The most common colors of MPs were blue and red, while the dominant MPs sizes were 0.1–0.5 mm and 0.5–1.0 mm. Of the eight identified polymers, PP, PE, and PET were the most common.ConclusionThis study reveals MPs characteristics (abundance, distribution, shape type, colors, size, polymers type) in surface sediment along the Montenegrin coast, as well as the most significant sources of MPs pollution, and provides important data for further research on MPs to identify the effects of MPs pollution on the quality, health, and functionality of the marine environment.

Physical and anthropogenic drivers shaping the spatial distribution of microplastics in the marine sediments of Chilean fjords

Several studies have focused on the presence and distribution of microplastics within the water column of coastal waters, but the dynamics of these particles in sediments have received little attention. Here we examine the concentrations and characteristics of microplastics in sediment samples collected from 35 stations within the Inner Sea of Chiloé, Chilean Patagonia. Current velocity, grain size, intensity of salmon farming activities, and human population density were all evaluated as factors potentially explaining concentrations and distribution of microplastic particles within these sediments. Microplastics were detected in all samples, with the highest abundance represented by fibers (88%), fragments (10%) and films (2%). Across the sampled sites, microplastic concentrations averaged 72.2 ± 32.4 (SD) items per kg dw (dry weight) sediment, with the principal polymers identified as polyethylene terephthalate (PET), acrylic, polypropylene (PP) and polyurethane (PUR). Approximately 40% of the variability in distribution and abundance of microplastics was explained by current velocity combined with proximity and intensity of local salmon production activities. SynopsisMarine currents and aquaculture intensity explain abundance and dynamics of microplastics in marine sediments.

Proposal for an initial screening method for identifying microplastics in marine sediments

Marine debris, which is often called microplastics, is widespread in marine environments, particularly in sediments, and is recognized as an environmental hazard because it concentrates contaminants, forms biofilms, and sinks into marine sediments. In sediments, it may be ingested by benthos and have a negative impact on higher food chain levels. In this study, a new protocol was developed to identify microplastics in various sediment fractions. This protocol combined sieving and staining based on ordinal geotechnical/geological testing methods. The sieving process was derived from the conventional particle size distribution test, and nontoxic dyes were employed in the staining process. The protocol is safe and easy to perform as it merely involves the use of conventional geological/geotechnical testing equipment. The new protocol was successfully employed to stain and categorize different types and sizes of microplastic particles from contaminated sediments. This safe, easy-to-use, and efficient protocol can serve as the basis for a new alternative approach to study microplastics present in sediments, which can be performed using basic materials familiar to geotechnical/geological engineers.

Design of a confocal micro-Raman spectroscopy system and research on microplastics detection.

Traditional micro-Raman spectroscopy technology has the disadvantages of a weak signal and low signal-to-noise ratio. To fix these issues, a cost-effective and rigorous design method is proposed in this paper, whereby a confocal micro-Raman spectroscopy system is designed and built, and a low-cost reflector and high-pass filter are introduced into the Raman signal-receiving module. The Raman light incident is fully perpendicular to the coupling lens by adjusting the reflection angle of the mirror, making the focus of the coupling lens highly conjugate with the focus of the microscope objective, to enhance the intensity of the Raman signal and improve the signal-to-noise ratio. In order to better apply this technology to the detection and study of microplastics in offshore sediments, a reflective illumination light path is used to avoid the visual interference caused by the capillary structure and opacity of the glass cellulose filter membrane. The detection and analysis of the microplastics on the glass cellulose filter membrane have been carried out by the confocal micro-Raman system designed, which is low cost and capable of obtaining good detection results and meeting the requirements of microplastics detection. The system designed in this paper is expected to be applied to the research and development of Raman detection equipment for microplastics in marine sediments, which is beneficial to promote the development of marine microplastic monitoring technology in the world.

Factors driving the abundance and distribution of microplastics on sandy beaches in a Southwest Atlantic seaside resort

Microplastics are currently considered widespread marine pollutants, accumulating in sediments and shorelines around the world. Spatial distribution of microplastics in marine sediments is consequence of a combination of multiple factors (naturals and anthropics). We evaluated the drivers' factors of the abundance and distribution of two microplastics morphotypes (fibers and fragments) in surface sediments (5 cm deep) on SW Atlantic beaches with different plastics waste contribution along the coastline. Beach geomorphology, sediment grain size, distance to the urban area, continental waters discharge and human activities were the analyzed factors. Fibers abundance was significantly highest in pocket beaches, moderately exposed and closest to the urban center, while the fragments abundance was highest in beaches with stormwater outfall. The fine sand and the high recreational level were also factors driving the abundance of both morphotypes. Therefore, plastic morphotype and abundance vary according to the determining factors.

Highlights from a review of microplastics in marine sediments

The ubiquity of microplastics (MPs) has now been demonstrated throughout Earth's geographic areas in both terrestrial and marine environments. Marine ecosystems are the end point of the plastic waste cycle, and marine sediments are increasingly considered to be a sink for plastic debris, with possible deleterious effects on seafloor ecosystems. However, the low concentration of MPs in a complex matrix such as marine sediment makes their reliable analysis difficult. MP concentration in marine sediments is usually determined by various extraction procedures followed by optical, spectroscopy or mass spectrometry techniques, and are therefore hard to compare. Therefore, reliable determination of MPs in sediment is a challenging task. Here we present a short review on studies dealing with analytical determination protocols and MP detection in marine sediments and discuss the advantages of the different techniques used. This analysis of the literature reveals that most of the 70 studies were carried out in European and Asian coastal environments. The use of NaCl saturated solution, hydrogen peroxide (H2O2) and Fourier transform infrared spectroscopy (FTIR) are by far the most-used techniques for the different steps of separation, digestion and identification, respectively. Based on this body of literature, we present recommendations and suggestions for future research in order to increase the reliability of results and to facilitate inter-comparison. The use of NaCl saturated and H2O2 solution is strongly recommended for the separation and digestion steps, respectively, whereas during the filtration step it is necessary to choose filter type based on the identification technique. More thorough investigation is needed to establish a systematic protocol for MP identification. A combination of techniques would permit to identify all items, and personal bias could be avoided if automatic identification was implemented. Nanoplastics (NP) occurrence in marine sediments is also discussed, although no data are available to date.

The role of oceanographic processes and sedimentological settings on the deposition of microplastics in marine sediment: Icelandic waters

The global distribution of microplastic debris on the sea floor poses an increasing risk to marine organisms and ecosystems. Here, we present a distribution analysis of microplastics collected from eight marine multicores recovered from the Iceland continental shelf and surrounding areas at water depth between 241 and 1628 m. We report a total of 306 microplastics from the size range > 250 μm −5 mm, of which all were fibers. Microplastic numbers range between 0.119 and 0.768 per gram of dry sediments. In the analysis we assess the potential role of oceanic surface and bottom water currents, organic content, and sediment type on the distribution, deposition, and burial of microplastics in marine sediments. Our results provide the first record of microplastic pollution of marine sediments from the Iceland continental shelf and identify Atlantic Cod feeding and breeding grounds as potential hot spot for the accumulation of marine debris.

Assessment of potential ecological risk of microplastics in the coastal sediments of India: A meta-analysis

Abundance, chemical composition and ecological risk of microplastics (MPs) in terrestrial and marine environments have merited substantial attention from the research communities. This is the first attempt to comprehend the ecological risk of MPs in sediments along the Indian coast using meta-data. Polymer hazard index (PHI), pollution load index (PLI) and potential ecological risk index (PERI) were used to evaluate the quality of sediments. Areas have high PHI values (>1000) due to the presence of polymers with high hazard scores such as polyamide (PA) and polystyrene (PS). According to PLI values, sediments along the west coast of India (WCI) are moderately contaminated with MPs (PLI: 3.03 to 15.5), whereas sediments along the east coast of India (ECI) are less contaminated (PLI: 1 to 6.14). The PERI values of sediments along the Indian coast showed higher ecological risk for the metropolitan cities, river mouths, potential fishing zones and the remote islands.

A novel thermoanalytical method for quantifying microplastics in marine sediments

Microplastic pollution in marine environments is of particular concern on its risk to the ecosystem. To assess and manage microplastic contaminants, their quantitative detection in environmental samples is a high priority. However, uncertainties of current methods still exist when estimating their abundances, particularly with fine-grained (<1 mm) microplastics. This work reports a novel thermoanalytical method for quantifying microplastics by measuring the contents of microplastic-derived carbon (MPC) in samples under the premise of nearly eliminating the limit of their particle appearances. After validating the method via samples with the spiked microplastics, we have conducted a case study on sediment core H43 that spanned 1925–2009 CE from the Yellow Sea for further illustrating the high reliability and practicability of this method for quantifying microplastics in natural samples. Our results have demonstrated that the proposed method may be a promising technique to determine the mass-related concentrations of the total microplastics in marine sediments for evaluating their pollution status and quantitative contribution to marine carbon storage.

Characterisation of microplastic contamination in sediment of England's inshore waters

Plastic litter is an increasingly significant problem in the marine environment. Our study looks at a cost-effective method to quantify larger fractions of microplastics in marine sediments as an opportunistic addition to standard benthic infauna sampling. A subsample of microplastics (>1 mm) were enumerated and categorised from sediment samples collected as part of standard benthic habitat monitoring in twenty-two Marine Protected Areas across English inshore waters. Microplastic particles were found in 61.2% of the samples collected, with mean density per study site ranging from 0.2 in Dover to Deal MCZ to 42.7 in The Mersey Estuary Special Protection Area microplastic particles per 0.1 m2. High densities of plastic were found at remote sites, as well as those closer to urban or industrialised areas. Spatial protection measures such as MPAs are not themselves a suitable tool to tackle marine plastic pollution which should be addressed upstream at source.

Microplastics in marine sediments and rabbitfish (Siganus fuscescens) from selected coastal areas of Negros Oriental, Philippines

The Philippines is currently ranked as the third top producer of plastic wastes, yet little research has been conducted on marine plastic pollution in this fishery-dependent, developing country. This study is the first in the nation to quantify and characterize microplastics ingested by a commercially important fish, the rabbitfish (Siganus fuscescens), in the coastal areas of Negros Oriental, central Philippines. Across all sites, the diversity of microplastic polymer types was highest in the guts of S. fuscescens from Dumaguete, a densely populated city. Microplastic particles extracted from subtidal sediment samples from Silliman Beach in Dumaguete were dominated by semi-synthetic microfibers (rayon), probably from clothing and textiles. However, these microplastic types were absent in the guts of fish, likely due to the different location and character of their feeding habitats. This study confirms for the first time the presence and diversity of microplastics in an edible finfish in the Philippines.

Detection of Adsorbed Chlordecone on Microplastics in Marine Sediments in Guadeloupe: A Preliminary Study

Plastic pollution in the oceans is recognized as a worldwide problem. Since the 1950s, the production of plastics has been increasing and the first reports of microplastics (particles < 500 μm) in the marine environment began to appear in the 1970s. These particles represent a growing environmental problem due to their dispersion in seawater and marine organisms. Additionally, microparticles in general can adsorb pollutants that will then become bioavailable to organisms by being desorbed during digestion, which could be an important pathway for the contamination of organisms. In Guadeloupe and Martinique, an organochlorine pesticide called “chlordecone” was used from 1972 to 1993 in banana plantations and this very persistent pollutant contaminates soils, rivers, and coastal marine areas and accumulates in marine foodwebs. To examine these issues, we had two goals: 1) to assess the contamination of marine sediments by microplastics surrounding Guadeloupe; and 2) to determine the ability of microplastics to adsorb chlordecone, as has been demonstrated for other organochlorine pollutants. To do so, marine sediments were collected in triplicate from 12 sites in coral reef environments around the island. Microplastics from each sample were then enumerated by size, color and shape under a binocular microscope. The results indicate that microplastics are found in all the studied sites and that their distribution could be linked to marine currents or proximity to areas of significant human activities (port activities, agglomeration, etc.). Finally, our preliminary results indicated that chlordecone could be adsorbed onto microplastics, with a concentration ranging from 0.00036—0.00173 µg/µg of microfilter.

Microplastics in marine sediments in the area of Pianosa Island (Central Adriatic Sea)

We investigated the occurrence of plastic contamination in sediments collected in the area of Pianosa Island (Adriatic Sea). In November 2015, 20 sediment samples were collected at depth varying between 119 and 142 m. At the laboratory, plastic debris in samples were weighted, measured and classified into dimensional groups, and categorized according to shape. Polymer types were identified using FT-IR analysis. All sediment samples contained plastics. In terms of numerical abundance, microplastics accounted for 64.4% of the total amount found. Filaments (66%) were the most common shape category. Identification through FT-IR spectroscopy evidenced the presence of 6 polymer types. Considering abundance, the majority of plastic debris were nylon (53.2%), followed by polyethylene (18%). By weight, polyethylene (61.4%) was the most represented polymer type, followed by polypropylene (19.6%). Because the distance from the coast, we hypothesize that plastics could be originated from marine-based sources including fishing vessels, merchant vessels and recreational boats.