Microm ID Fused-silica Capillaries Research Articles

Field‐amplified sample injection‐micellar electrokinetic capillary chromatography for the analysis of bisphenol A, bisphenol F, and their diglycidyl ethers and derivatives in canned soft drinks

Conditions were established for the separation and analysis of bisphenol A, bisphenol F, and their diglycidyl ethers by micellar electrokinetic capillary chromatography (MECC). Good resolution was obtained for all compounds, although in order to achieve the separation of ortho-ortho, ortho-para, and para-para isomers of bisphenol F diglycidyl ether (BFDGE), BFDGE x 2H(2)O and BFDGE x 2HCl, it was necessary to use a 25 microm id fused silica capillary. To increase sensitivity, a field-amplified sample injection (FASI)-MECC method was developed using 10 mM SDS solution as injection matrix and a 75 microm id fused silica capillary. Instrumental quality parameters such as LODs (<55 microg/L with standards), linearity (r(2)>0.999), and run-to-run and day-to-day precisions (RSD values lower than 12.5%) were determined. Finally, the suitability of the FASI-MECC method for the analysis of bisphenol A, bisphenol F, and their diglycidyl ethers in canned soft drinks was evaluated. Quantitation was performed by matrix-matched calibration using a plastic-bottled isotonic drink as matrix. The results showed that FASI-MECC is an economic method for the screening and quantitation of these kinds of compounds in soft drink beverages, with no loss of reproducibility, and effective at concentrations lower than the specific migration level values established by the European Union.

Assessment of ion transfer amperometry at liquid–liquid interfaces for detection in CE

In this research, ion transfer across the interface between two immiscible electrolyte solutions (ITIES) was used as a method of detection in a CE separation system. This method allows for the electrochemical detection of ionic analytes that cannot be easily oxidized or reduced. Method development revealed that the optimal separation conditions for three model ions (tetraethylammonium, tetrabutylammonium, and benzensulfonate) were found to be 5 mM sodium tetraborate buffer pH 9.2 with a separation voltage of 20 kV using a 40 cm, 50 microm id fused silica capillary. Constant potential amperometry and pulsed amperometric detection were applied at the ITIES in which the organic phase was gelled. A miniaturized ITIES within a pipette tip was investigated, which resulted in improved separation efficiency and LOD. To demonstrate the ability of the system to detect substances of bioanalytical interest, the beta-adrenergic receptor blockers timolol and propranolol were detected. The simplicity of the detection platform means that it may be useful for analytical situations not requiring trace or ultratrace detection capabilities.

Monolithic poly(1,2‐bis(p‐vinylphenyl)ethane) capillary columns for simultaneous separation of low‐ and high‐molecular‐weight compounds

Monolithic poly(1,2-bis(p-vinylphenyl)ethane (BVPE)) capillary columns were prepared by thermally initiated free radical polymerisation of 1,2-bis(p-vinylphenyl)ethane in the presence of inert diluents (porogens) and alpha,alpha'-azoisobutyronitrile (AIBN) as initiator. Polymerisations were accomplished in 200 microm ID fused silica capillaries at 65 degrees C and for 60 min. Mercury intrusion porosimetry measurements of the polymeric RP support showed a broad bimodal pore-size-distribution of mesopores and small macropores in the range of 5-400 nm and flow-channels in the mum range. N(2)-adsorption (BET) analysis resulted in a tremendous enhancement of surface area (101 m(2)/g) of BVPE stationary phases compared to typical organic monoliths (approximately 20 m(2)/g), indicating the presence of a considerable amount of mesopores. Consequently, the adequate proportion of both meso- and (small) macropores allowed the rapid and high-resolution separation of low-molecular-weight compounds as well as biomolecules on the same monolithic support. At the same time, the high fraction of flow-channels provided enhanced column permeability. The chromatographic performance of poly(1,2-bis(p-vinylphenyl)ethane) capillary columns for the separation of biomolecules (proteins, oligonucleotides) and small molecules (alkyl benzenes, phenols, phenons) are demonstrated in this article. Additionally, pressure drop versus flow rate measurements of novel poly(1,2-bis(p-vinylphenyl)ethane) capillary columns confirmed high mechanical robustness, low swelling in organic solvents and high permeability. Due to the simplicity of monolith fabrication, comprehensive studies of the retention and separation behaviour of monolithic BVPE columns resulted in high run-to-run and batch-to-batch reproducibilities. All these attributes prove the excellent applicability of monolithic poly(1,2-bis(p-vinylphenyl)ethane) capillary columns for micro-HPLC towards a huge range of analytes of different chemistries and molecular sizes.

Highly cross‐linked polymeric capillary monoliths for the separation of low, medium, and high molecular weight analytes

Highly rigid capillary monoliths with low swelling propensity were prepared within the confines of 200 microm ID fused silica capillaries via thermally induced free radical polymerization of tetrakis(4-vinylbenzyl)silane (TVBS) in the presence of 1-dodecanol and toluene. alpha,alpha'-Azobisisobutyronitrile (AIBN) was used as initiator. The resulting monoliths were optimized for the separation of low, medium, and high molecular weight analytes. The microstructure and porosity of the monoliths prepared were studied by SEM and inverse size-exclusion chromatography (ISEC). The porosity of the monolithic supports was tuned by varying the amount of initiator (i. e. AIBN) between 0.5 and 2 wt%. All monoliths were tested for a series of low molecular weight compounds including alkylbenzenes, amines, carboxylic acids, phenols, carbonyl compounds, and beta-blockers, as well as for the separation of medium molecular weight analytes such as peptides and high-molecular weight analytes such as proteins. Due to the microporous structure, the novel monoliths displayed high efficiency and performance particularly in the separation of low molecular weight analytes. Relevant chromatographic parameters including permeability, swelling propensity, and height equivalents to theoretical plates were determined.

Capillary electrochromatography of biologically relevant flavonoids

Flavonoids were separated utilizing CEC technique. Baseline separation of biologically relevant flavonoids was obtained using a 100 microm ID fused-silica capillary filled with 3 microm Silica-C18 material and an optimized mobile phase comprising of 20 mM Tris-HCl (pH 6.5), ACN and water at a ratio of 10/40/50 v/v/v. Separations were carried out at 25 kV and a column temperature of 25 degrees C. The influence of relevant parameters for the CEC separation, such as buffer concentration, pH, separation voltage, and ACN concentration, was investigated and optimized. Dependencies of the electroendoosmotic flow (EOF) on these parameters and effects on the resolution of the analytes were studied. During analyses the solvents used for dissolving the samples turned out to have significant effects on the separation of flavonoids. The optimized system was then successfully used for the separation of the flavonoids epicatechin, myricetin, quercetin, naringenin, and hesperetin. CEC turned out to be a useful complementary tool for the economic analysis of flavonoids in addition to common HPLC, muHPLC, and CE methodologies. This method can be used for real applications in phytomics.

Chararacterization of a monolithic immobilized trypsin microreactor with on‐line coupling to ESI‐MS

The preparation and characterization of a miniaturized trypsin reactor using on-line coupling with an ESI-TOF mass spectrometer are described. L-1-Tosylamido-2-phenylethyl chloromethyl ketone-trypsin was covalently immobilized on poly(glycidyl methacrylate-co-ethylene dimethacrylate) monolith prepared in a 75 microm ID fused silica capillary resulting in a bioreactor with high local concentration of the proteolytic enzyme. Covalent immobilization of trypsin on this support was performed using the epoxide functional groups in either a one- or a multistep reaction. For on-line protein digestion-MS analysis the bioreactor was coupled with the mass spectrometer using a liquid junction microelectrospray interface. The performance of the reactor was tested using an on-line flow through the system with flow rates of 50-300 nL/min. The resulting protein consumption was in the atto- to low femtomole range. Proteolytic activity was characterized in a wide range of conditions with respect to the flow rate, pH, and temperature. Complete protein digestion was achieved in less than 30 s at 25 degrees C with the sequence coverage of 80% (cytochrome c), which is comparable to 3 h digestion in solution at 37 degrees C. Besides the good performance at laboratory temperature, the immobilized trypsin in the bioreactor also performed well at lower pH compared to the standard in-solution protocols.

Speciation of arsenic compounds in fish and oyster tissues by capillary electrophoresis‐inductively coupled plasma‐mass spectrometry

A capillary electrophoresis-inductively coupled plasma-mass spectrometric (CE-ICP-MS) method for the speciation of six arsenic compounds, namely arsenite [As(III)], arsenate [As(V)], monomethylarsonic acid, dimethylarsinic acid, arsenobetaine and arsenocholine is described. The separation has been achieved on a 70 cm length x 75 microm ID fused-silica capillary. The electrophoretic buffer used was 15 mM Tris (pH 9.0) containing 15 mM sodium dodecyl sulfate (SDS), while the applied voltage was set at +22 kV. The arsenic species in biological tissues were extracted into 80% v/v methanol-water mixture, put in a closed centrifuge tube and kept in a water bath, using microwaves at 80 degrees C for 3 min. The extraction efficiencies of individual arsenic species added to the sample at 0.5 microg As/g level were between 96% and 107%, except for As(III), for which it was 89% and 77% for oyster and fish samples, respectively. The detection limits of the species studied were in the range 0.3-0.5 ng As/mL. The procedure has been applied for the speciation analysis of two reference materials, namely dogfish muscle tissue (NRCC DORM-2) and oyster tissue (NIST SRM 1566a), and two real-world samples.

Capillary electrochromatography with monolithic silica column: I. Preparation of silica monoliths having surface-bound octadecyl moieties and their chromatographic characterization and applications to the separation of neutral and charged species.

Monolithic silica columns with surface-bound octadecyl (C18) moieties have been prepared by a sol-gel process in 100 microm ID fused-silica capillaries for reversed-phase capillary electrochromatography of neutral and charged species. The reaction conditions for the preparation of the C18-silica monoliths were optimized for maximum surface coverage with octadecyl moieties in order to maximize retention and selectivity toward neutral and charged solutes with a sufficiently strong electroosmotic flow (> 2 mm/s) to yield rapid analysis time. Furthermore, the effect of the pore-tailoring process on the silica monoliths was performed over a wide range of treatment time with 0.010 M ammonium hydroxide solution in order to determine the optimum time and conditions that yield mesopores of narrow pore size distribution that result in high separation efficiency. Under optimum column fabrication conditions and optimum mobile phase composition and flow velocity, the average separation efficiency reached 160 000 plates/m, a value comparable to that obtained on columns packed with 3 microm C18-silica particles with the advantages of high permeability and virtually no bubble formation. The optimized monolithic C18-silica columns were evaluated for their retention properties toward neutral and charged analytes over a wide range of mobile phase compositions. A series of dimensionless retention parameters were evaluated and correlated to solute polarity and electromigration property. A dimensionless mobility modulus was introduced to describe charged solute migration and interaction behavior with the monolithic C18-silica in a counterflow regime during capillary electrochromatography (CEC )separations. The mobility moduli correlated well with the solute hydrophobic character and its charge-to-mass ratio.

Determination of monophosphate nucleotides by capillary electrophoresis inductively coupled plasma mass spectrometry.

A preliminary study of a modified microconcentric nebulizer (CEI-100, CETAC) as the sample introduction device of capillary electrophoresis inductively coupled plasma mass spectrometry (CE-ICP-MS) for the determination of monophosphate nucleotides is described. The monophosphate nucleotides studied include adenosine 5'-monophosphate (AMP), guanosine 5'-monophosphate (GMP), uridine 5'-monophosphate (UMP) and inosine 5'-monophosphate (IMP). The species studied were well separated using a 70 cm length x 75 microm id fused silica capillary while the applied voltage was set at -22 kV and a 20 mmol l(-1) ammonium citrate/citric acid buffer (pH 4.0) containing 0.1% m/v cationic polymer (hexadimethrine bromide, Polybrene) was used as the electrophoretic buffer. The electroosmotic flow was reversed by flushing the fused silica capillary with 0.2% m/v Polybrene to accelerate separation. The detection limit of various species studied was in the range of 0.036-0.054 microg P ml(-1), which corresponded to the absolute detection limit of 1.1-1.6 pg P based on the injection volume of 30 nl. We determined the concentrations of nucleotides in two IG-enriched monosodium glutamates purchased from the local market. The recovery was in the range of 100-112% for various species, and the concentrations of IMP and GMP in these samples were in the range of 0.15-0.18% m/m.

Use of vancomycin silica stationary phase in packed capillary electrochromatography I. Enantiomer separation of basic compounds

Chiral separation of basic compounds was achieved by using 75 or 100 microm ID fused-silica capillaries packed with a vanoomycin-modified diol silica stationary phase. The capillary was firstly packed for about 12 cm with a slurry mixture composed of diolsilica (3:1) then with the vancomycin modified diol-silica (3:1) (23 cm), and finally with diol-silica (3:1) for about 2 cm. Frits were prepared by a heating wire at the two ends of the capillary; the detector window was prepared at 8.5 cm from the end of the capillary where vancomycin was not present. The influence of the mobile phase composition (pH and concentration, organic modifier type and concentration) on the velocity of the electroosmotic flow, chiral resolution and enantioselectivity was studied. Good enantiomeric resolution was achieved for atenolol, oxprenolol, propranolol, and venlafaxine using a mobile phase composition of 100 mM ammonium acetate solution (pH 6)/water/acetonitrile (5:5:90 v/v/v) while for terbutaline a mixture of 5:15:80 v/v/v provided the best separations. The use of methanol instead of acetonitrile caused a general increase of enantiomer resolution of the studied compounds together with a reduction of efficiency and detector response. However, the combination of acetonitrile and methanol in the mobile phase (as, e.g., 10% methanol and 80% acetonitrile) allowed to improve the enantiomer resolution with satisfactory detector response.

Molecular imprint polymers as highly selective stationary phases for open tubular liquid chromatography and capillary electrochromatography.

Chiral separations employing molecular imprint polymer (MIP) stationary phases in both open tubular liquid chromatography (OT-LC) and capillary electrochromatography (OT-CEC) are demonstrated. MIPs are highly crosslinked polymers containing spatial and functionality memory of template molecules which provide a higher degree of selectivity when used as stationary phases for chromatographic separations. Thin films of molecular imprinted polymers bonded to the inner walls of 25 microm ID fused-silica capillaries were prepared using an in situ polymerization technique developed in our laboratory that allows the use of conventional fused-silica capillaries with polyimide outer coatings. The success rate in preparing such open tubular columns was about 70%. Methacrylic acid and 2-vinyl pyridine were chosen as functional monomers, and either ethylene dimethacrylate or trimethylol propane trimethacrylate was used as the crosslinker. Toluene was employed as the porogen. Effects of polymerization conditions on column preparation and chromatographic performance were studied. Enantiomeric separations of D- and L-dansyl phenylalanines were achieved in both OT-LC and OT-CEC modes with good selectivity and efficiencies. Both types of separations may be performed on the same column using a single commercial instrument.

Capillary electrophoresis of peptides and proteins in fused-silica capillaries coated with derivatized polystyrene nanoparticles.

High-resolution capillary electrophoretic separation of proteins and peptides was achieved by coating the inner wall of 75 microm ID fused-silica capillaries with 40-140 nm polystyrene particles which have been derivatized with alpha-omega-diamines such as ethylenediamine or 1,10-diaminodecane. A stable and irreversibly adsorbed coating was obtained upon deprotonation of the capillary surface with aqueous sodium hydroxide and subsequent flushing with a suspension of the positively charged particles. At pH 3.1, the detrimental adsorption of proteins to the capillary inner wall was suppressed efficiently because of electrostatic repulsion of the positively charged proteins from the positively charged coating which enabled protein separations with maximum efficiencies of 400000 plates per meter. A substantial improvement of separation efficiency in particle-coated capillaries was observed after in-column derivatization of amino functionalities with 2,3-epoxy-l-propanol, resulting in a more hydrophilic coating. Five basic and four acidic proteins could be separated in less than 7 min with efficiencies up to 1900000 theoretical plates per meter. Finally, coated capillaries were applied to the high-resolution analysis of protein glycoforms and bioactive peptides.