Microfibrous Scaffolds Research Articles

Osteogenic Potential and Long-Term Enzymatic Biodegradation of PHB-based Scaffolds with Composite Magnetic Nanofillers in a Magnetic Field.

Millions of people worldwide suffer from musculoskeletal damage, thus using the largest proportion of rehabilitation services. The limited self-regenerative capacity of bone and cartilage tissues necessitates the development of functional biomaterials. Magnetoactive materials are a promising solution due to clinical safety and deep tissue penetration of magnetic fields (MFs) without attenuation and tissue heating. Herein, electrospun microfibrous scaffolds were developed based on piezoelectric poly(3-hydroxybutyrate) (PHB) and composite magnetic nanofillers [magnetite with graphene oxide (GO) or reduced GO]. The scaffolds' morphology, structure, mechanical properties, surface potential, and piezoelectric response were systematically investigated. Furthermore, a complex mechanism of enzymatic biodegradation of these scaffolds is proposed that involves (i) a release of polymer crystallites, (ii) crystallization of the amorphous phase, and (iii) dissolution of the amorphous phase. Incorporation of Fe3O4, Fe3O4-GO, or Fe3O4-rGO accelerated the biodegradation of PHB scaffolds owing to pores on the surface of composite fibers and the enlarged content of polymer amorphous phase in the composite scaffolds. Six-month biodegradation caused a reduction in surface potential (1.5-fold) and in a vertical piezoresponse (3.5-fold) of the Fe3O4-GO scaffold because of a decrease in the PHB β-phase content. In vitro assays in the absence of an MF showed a significantly more pronounced mesenchymal stem cell proliferation on composite magnetic scaffolds compared to the neat scaffold, whereas in an MF (68 mT, 0.67 Hz), cell proliferation was not statistically significantly different when all the studied scaffolds were compared. The PHB/Fe3O4-GO scaffold was implanted into femur bone defects in rats, resulting in successful bone repair after nonperiodic magnetic stimulation (200 mT, 0.04 Hz) owing to a synergetic influence of increased surface roughness, the presence of hydrophilic groups near the surface, and magnetoelectric and magnetomechanical effects of the material.

Fabrication of 3D microfibrous composite polycaprolactone/hydroxyapatite scaffolds loaded with piezoelectric poly (lactic acid) nanofibers by sequential near-field and conventional electrospinning for bone tissue engineering

Near-field electrospinning (NFES) has recently gained considerable interest in fabricating tissue engineering scaffolds. This technique combines the advantages of both 3D printing and electrospinning. It allows for the production of fibers with smaller resolution and the ability to make regular structures with suitable pores. In this study, a microfibrous composite scaffold of polycaprolactone (PCL)/hydroxyapatite (HA) was prepared by NFES in the first step. The microfibrous scaffold had a fiber spacing of 414.674 ± 24.9 μm with an average fiber diameter of 94.695 ± 16.149 μm. However, due to the large fiber spacing, the surface area was insufficient for cell adhesion. Therefore, the hybrid scaffold was prepared by adding aligned and random electrospun poly (L-lactic acid) (PLLA) nanofibers to the microfibrous scaffold. Cellular studies showed that cell adhesion to the hybrid scaffold increased by 334 % compared to the microfibrous scaffold. These nanofibers also exhibited piezoelectric properties, which helped stimulate bone regeneration. Aligned nanofibers in the hybrid scaffold enhanced alkaline phosphatase activity and the intensity of alizarin red staining 1.5 and 1.6 times, respectively, compared to the microfibrous scaffold. Furthermore, the elastic modulus and ultimate tensile strength increased by 268 % and 130 %, respectively, by adding aligned nanofibers to the microfibrous scaffold. Therefore, the hybrid microfibrous composite scaffold of PCL/HA containing aligned electrospun PLLA nanofibers with improved properties showed the potential for bone regeneration.

Dye-sensitized sepiolite clay as natural scaffolds for visible light driven photocatalytic hydrogen evolution

Natural clay minerals are increasingly used as superior support materials for various photocatalysts due to their excellent adsorption capacity, negative surface charge, suitable thermal/chemical stability, large specific surface area, and strong surface reactivity, resulting in low agglomeration and suppression of charge recombination. However, they are still insufficient for photocatalysis due to their low efficiency. Therefore, sensitization of clay minerals with dyes to improve the efficiency and specificity of catalysts is considered a promising route for photocatalytic applications. In this work, the effect of dye sensitization on visible light-driven photocatalytic water splitting of microfibrous sepiolite scaffolds as natural photocatalyst supports was investigated for the first time by using various xanthene dyes (eosin Y, rhodamine B and eryhtrosine B (ErB)) and triethanolamine as photosensitizers and sacrificial agents, respectively, in the absence and presence of platinum as a co-catalyst. The clay/dye system was characterized using various techniques such as X-ray photoelectron spectroscopy, transmission electron microscopy, scanning electron microscopy and energy dispersive X-rays. Sep/ErB photocatalysts produced the highest amount of hydrogen among the other Sep/dye scaffold systems because they act as an effective matrix by preventing nanoparticle aggregation and promoting electron transfer due to their excellent crystal structures and physicochemical properties.

Coaxial electrohydrodynamic printing of core–shell microfibrous scaffolds with layer-specific growth factors release for enthesis regeneration

The rotator cuff tear has emerged as a significant global health concern. However, existing therapies fail to fully restore the intricate bone-to-tendon gradients, resulting in compromised biomechanical functionalities of the reconstructed enthesis tissues. Herein, a tri-layered core–shell microfibrous scaffold with layer-specific growth factors (GFs) release is developed using coaxial electrohydrodynamic (EHD) printing for in situ cell recruitment and differentiation to facilitate gradient enthesis tissue repair. Stromal cell-derived factor-1 (SDF-1) is loaded in the shell, while basic fibroblast GF, transforming GF-beta, and bone morphogenetic protein-2 are loaded in the core of the EHD-printed microfibrous scaffolds in a layer-specific manner. Correspondingly, the tri-layered microfibrous scaffolds have a core–shell fiber size of (25.7 ± 5.1) μm, with a pore size sequentially increasing from (81.5 ± 4.6) μm to (173.3 ± 6.9) μm, and to (388.9 ± 6.9 μm) for the tenogenic, chondrogenic, and osteogenic instructive layers. A rapid release of embedded GFs is observed within the first 2 d, followed by a faster release of SDF-1 and a slightly slower release of differentiation GFs for approximately four weeks. The coaxial EHD-printed microfibrous scaffolds significantly promote stem cell recruitment and direct their differentiation toward tenocyte, chondrocyte, and osteocyte phenotypes in vitro. When implanted in vivo, the tri-layered core–shell microfibrous scaffolds rapidly restored the biomechanical functions and promoted enthesis tissue regeneration with native-like bone-to-tendon gradients. Our findings suggest that the microfibrous scaffolds with layer-specific GFs release may offer a promising clinical solution for enthesis regeneration.

Three-Dimensional Microfibrous Scaffold with Aligned Topography Produced via a Combination of Melt-Extrusion Additive Manufacturing and Porogen Leaching for In Vitro Skeletal Muscle Modeling.

Skeletal muscle tissue (SMT) has a highly hierarchical and anisotropic morphology, featuring aligned and parallel structures at multiple levels. Various factors, including trauma and disease conditions, can compromise the functionality of skeletal muscle. The in vitro modeling of SMT represents a useful tool for testing novel drugs and therapies. The successful replication of SMT native morphology demands scaffolds with an aligned anisotropic 3D architecture. In this work, a 3D PCL fibrous scaffold with aligned morphology was developed through the synergistic combination of Melt-Extrusion Additive Manufacturing (MEAM) and porogen leaching, utilizing PCL as the bulk material and PEG as the porogen. PCL/PEG blends with different polymer ratios (60/40, 50/50, 40/60) were produced and characterized through a DSC analysis. The MEAM process parameters and porogen leaching in bi-distilled water allowed for the development of a micrometric anisotropic fibrous structure with fiber diameters ranging from 10 to 100 µm, depending on PCL/PEG blend ratios. The fibrous scaffolds were coated with Gelatin type A to achieve a biomimetic coating for an in vitro cell culture and mechanically characterized via AFM. The 40/60 PCL/PEG scaffolds yielded the most homogeneous and smallest fibers and the greatest physiological stiffness. In vitro cell culture studies were performed by seeding C2C12 cells onto a selected scaffold, enabling their attachment, alignment, and myotube formation along the PCL fibers during a 14-day culture period. The resultant anisotropic scaffold morphology promoted SMT-like cell conformation, establishing a versatile platform for developing in vitro models of tissues with anisotropic morphology.

Abstract 6769: Applications of a novel fibrous extracellular matrix for advanced in vitro cancer models

Abstract Compared to traditional in vitro two-dimensional (2D) planar cell culture system, three-dimensional (3D) mammalian cell culture can better recapitulate physiological environments and the complexity of natural tissues, hence they are crucial in modern biomedical research. Extracellular matrices (ECM) play a key role in in vitro mammalian cell culture systems. The role of the ECM on in vitro 3D cell culture are: 1) to simulate an in vivo-like physiological environment, 2) support cell-cell and cell-ECM interactions, 3) promote cell adhesion, migration, and communication, 4) aid in tissue development, morphogenesis, differentiation, and functioning. Although basal membrane extracts (BME) are the most popular type of ECM supporting 3D modeling in vitro, they often have significant limitations including limited long-term stability, significant batch to batch heterogeneity, restricted cell movement, and relatively high cost for culturing many cancer cell lines. In this investigation, we employ a novel micro-fibrous scaffold that closely mimics natural ECM, providing porous and interconnected networks for 3D culturing of hepatic cells, lung cancer, breast cancer, pancreatic cancer. As revealed by optical and scanning electron microscopy, the scaffold promotes significant cell-to-cell and cell-to-matrix interactions. Moreover, we observed improved cell growth in 3D culture over longer periods than 2D culture systems for all cell types examined. We also evaluated the anticancer efficiency of different drugs including Lapatinib, Cisplatin, Docetaxel, Doxorubicin and observed that 2D cultured cells were more sensitive to drugs treatment in comparison to 3D. Furthermore, ECM was observed to support 3D growth and structure formation with cell pools of primary cells achieved from disassociated human tumors. Tumor organoids were able to form within seven days and ready for anticancer screening within 14 days. We achieved an 80% success rate in developing breast cancer organoids from patient tissues. Additionally, tissue granules were also able to be cultured under the same condition, which allowed us to investigate the invasion of cancer cells into tissue. The primary cells from human tumors formed cell clusters resembling the original tumor tissue's structure. In conclusion, the novel micro-fibrous scaffold, closely mimicking natural extracellular matrixes, promotes significant cell-to-cell and cell-to-matrix interactions, while also facilitating cell growth over extended periods providing a more physiologically relevant platform for evaluating drug responses for various cancer cell types, further showing the importance of 3D culture systems in cancer research. Citation Format: Navneet Kaur, Dazhi Yang, Jamel Ali. Applications of a novel fibrous extracellular matrix for advanced in vitro cancer models [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2024; Part 1 (Regular Abstracts); 2024 Apr 5-10; San Diego, CA. Philadelphia (PA): AACR; Cancer Res 2024;84(6_Suppl):Abstract nr 6769.

The fabrication method impacts biological properties of microfibrous three-dimensional in vitro cell culture scaffolds and their applications in drug screening

Two-dimensional (2D) cell culture models cannot accurately emulate the three-dimensional (3D) in vivo microenvironment; hence, the shift from compound screening in traditional 2D well plates to 3D cell culture models is forthcoming. New scaffold designs must comply with the 3Rs principle to reduce the use of animal-derived products, such as natural proteins. In line with this motivation, we engineered and compared various fibrous scaffolds featuring diverse fibre networks (coarse and fine fibres) and fibre surface properties (porous vs. smooth fibres), and tested them in in vitro cell culture. We fabricated coarse solid fibre scaffolds via a melt-based electrohydrodynamic process, which resulted in fibres with a diameter of 10.6 ± 1.9 µm and a porosity of 87.1 ± 0.9%. Using solution-based cryo-electrohydrodynamic process, we fabricated fine porous fibre and fine solid fibre scaffolds that exhibited fibres of 2.01 ± 0.5 µm and 1.72 ± 0.6 µm in diameter, with porosities of 96.5 ± 0.3% and 94.4 ± 0.5%, respectively. The scaffolds underwent only chemical modification via an alkaline treatment to enhance their hydrophilicity. We used mouse fibroblast L929 cells and human triple-negative breast cancer MDA-MB-231 cells as cell models, and used the MTT assay to measure their viability. After seven days of cell culture, all scaffolds were thoroughly penetrated. However, the coarse scaffolds created by the melt-based electrohydrodynamic process and the porous fibre scaffolds produced by the solution-based cryo-electrohydrodynamic process outperformed the simpler morphology of smooth fine fibres. Furthermore, the 50% half-maximum effective concentration (EC50) of doxorubicin tested in human glioblastoma (U87-MG) and human triple-negative breast cancer (MDA-MB-231) cell lines in 3D cell culture models was approximately twice as high as that achieved in conventional 2D cell cultures. Therefore, we infer that poly (ɛ-caprolactone) (PCL) microfibre scaffolds, devoid of animal-derived product surface treatment, may provide a favourable 3D milieu for various cell types for in vitro studies.

Impact of the Reduction Time-Dependent Electrical Conductivity of Graphene Nanoplatelet-Coated Aligned Bombyx mori Silk Scaffolds on Electrically Stimulated Axonal Growth.

Graphene-based nanomaterials, renowned for their outstanding electrical conductivity, have been extensively studied as electroconductive biomaterials (ECBs) for electrically stimulated tissue regeneration. However, using eco-friendly reducing agents like l-ascorbic acid (l-Aa) can result in lower conductive properties in these ECBs, limiting their full potential for smooth charge transfer in living tissues. Moreover, creating a flexible biomaterial scaffold using these materials that accurately mimics a specific tissue microarchitecture, such as nerves, poses additional challenges. To address these issues, this study developed a microfibrous scaffold of Bombyx mori (Bm) silk fibroin uniformly coated with graphene nanoplatelets (GNPs) through a vacuum coating method. The scaffold's electrical conductivity was optimized by varying the reduction period using l-Aa. The research systematically investigated how different reduction periods impact scaffold properties, focusing on electrical conductivity and its significance on electrically stimulated axonal growth in PC12 cells. Results showed that a 48 h reduction significantly increased surface electrical conductivity by 100-1000 times compared to a shorter or no reduction process. l-Aa contributed to stabilizing the reduced GNPs, demonstrated by a slow degradation profile and sustained conductivity even after 60 days in a proteolytic environment. β (III) tubulin immunostaining of PC12 cells on varied silk:GNP scaffolds under pulsed electrical stimulation (ES, 50 Hz frequency, 1 ms pulse width, and amplitudes of 100 and 300 mV/cm) demonstrates accelerated axonal growth on scaffolds exhibiting higher conductivity. This is supported by upregulated intracellular Ca2+ dynamics immediately after ES on the scaffolds with higher conductivity, subjected to a prolonged reduction period. The study showcases a sustainable reduction approach using l-Aa in combination with natural Bm silk fibroin to create a highly conductive, mechanically robust, and stable silk:GNP-based aligned fibrous scaffold. These scaffolds hold promise for functional regeneration in electrically excitable tissues such as nerves, cardiac tissue, and muscles.

Improvement of Osteogenic Differentiation of Mouse Pre-Osteoblastic MC3T3-E1 Cells on Core-Shell Polylactic Acid/Chitosan Electrospun Scaffolds for Bone Defect Repair.

Electrospun hybrid scaffolds composed of synthetic and natural polymers have gained increasing interest in tissue engineering applications over the last decade. In this work, scaffolds composed of polylactic acid electrospun fibers, either treated (P-PLA) or non-treated (PLA) with air-plasma, were coated with high molecular weight chitosan to create a core-shell microfibrous structure. The effective thickness control of the chitosan layer was confirmed by gravimetric, spectroscopic (FTIR-ATR) and morphological (SEM) investigations. The chitosan coating increased the fiber diameter of the microfibrous scaffolds while the tensile mechanical tests, conducted in dry and wet environments, showed a reinforcing action of the coating layer on the scaffolds, in particular when deposited on P-PLA samples. The stability of the Chi coating on both PLA and P-PLA substrates was confirmed by gravimetric analysis, while their mineralization capacity was evaluated though scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) after immersing the scaffolds in simulated body fluids (SBF) at 37 °C for 1 week. Sample biocompatibility was investigated through cell viability assay and SEM analysis on mouse pre-osteoblastic MC3T3-E1 cells grown on scaffolds at different times (1, 7, 14 and 21 days). Finally, Alizarin Red assay and qPCR analysis suggested that the combination of plasma treatment and chitosan coating on PLA electrospun scaffolds influences the osteoblastic differentiation of MC3T3-E1 cells, thus demonstrating the great potential of P-PLA/chitosan hybrid scaffolds for bone tissue engineering applications.

Development and Evaluation of Biodegradable Core-Shell Microfibrous and Nanofibrous Scaffolds for Tissue Engineering Applications

Tissue engineering scaffolds as three-dimensional substrates may serve as ideal templates for tissue regeneration by simulating the structure of the extracellular matrix (ECM). Many biodegradable synthetic polymers, either hydrophobic, like Poly-ε-caprolactone (PCL), or hydrophilic, like Poly(Vinyl Alcohol) (PVA), are widely used as candidate bioactive materials for fabricating tissue engineering scaffolds. However, a combination of good cytocompatibility of hydrophilic polymers with good biomechanical performance of hydrophobic polymers could be beneficial for the in vivo performance of the scaffolds. In this study, we aimed to fabricate biodegradable fibrous scaffolds by combining the properties of hydrophobic PCL with those of hydrophilic PVA and evaluate their properties in comparison with pristine PCL scaffolds. Therefore, single-layered PCL scaffolds, sequential tri-layered (PVA/PCL/PVA), and core-shell (PVA as shell and PCL as core) composite scaffolds were developed utilizing the electrospinning technique. The material structural and biomechanical properties of the electrospun scaffolds, before and after their hydrolytic degradation over a seven-month period following storage in phosphate-buffered saline (PBS) at 37 °C, were comprehensively compared. In addition, human embryonic kidney cells (HEK-293) were cultured on the scaffolds to investigate potential cell attachment, infiltration, and proliferation. The results demonstrated the long-term efficacy of core-shell biodegradable fibrous scaffolds in comparison to single-layers PCL and tri-layers PVA/PCL/PVA, not only due to its superior morphological characteristics and mechanical properties, but also due to its ability to promote homogeneous cell distribution and proliferation, without any external chemical or physical stimuli.Graphical

Highly compliant biomimetic scaffolds for small diameter tissue-engineered vascular grafts (TEVGs) produced via melt electrowriting (MEW)

Biofabrication approaches toward the development of tissue-engineered vascular grafts (TEVGs) have been widely investigated. However, successful translation has been limited to large diameter applications, with small diameter grafts frequently failing due to poor mechanical performance, in particular mismatched radial compliance. Herein, melt electrowriting (MEW) of poly(ϵ-caprolactone) has enabled the manufacture of highly porous, biocompatible microfibre scaffolds with physiological anisotropic mechanical properties, as substrates for the biofabrication of small diameter TEVGs. Highly reproducible scaffolds with internal diameter of 4.0 mm were designed with 500 and 250 µm pore sizes, demonstrating minimal deviation of less than 4% from the intended architecture, with consistent fibre diameter of 15 ± 2 µm across groups. Scaffolds were designed with straight or sinusoidal circumferential microfibre architecture respectively, to investigate the influence of biomimetic fibre straightening on radial compliance. The results demonstrate that scaffolds with wave-like circumferential microfibre laydown patterns mimicking the architectural arrangement of collagen fibres in arteries, exhibit physiological compliance (12.9 ± 0.6% per 100 mmHg), while equivalent control geometries with straight fibres exhibit significantly reduced compliance (5.5 ± 0.1% per 100 mmHg). Further mechanical characterisation revealed the sinusoidal scaffolds designed with 250 µm pores exhibited physiologically relevant burst pressures of 1078 ± 236 mmHg, compared to 631 ± 105 mmHg for corresponding 500 µm controls. Similar trends were observed for strength and failure, indicating enhanced mechanical performance of scaffolds with reduced pore spacing. Preliminary in vitro culture of human mesenchymal stem cells validated the MEW scaffolds as suitable substrates for cellular growth and proliferation, with high cell viability (>90%) and coverage (>85%), with subsequent seeding of vascular endothelial cells indicating successful attachment and preliminary endothelialisation of tissue-cultured constructs. These findings support further investigation into long-term tissue culture methodologies for enhanced production of vascular extracellular matrix components, toward the development of the next generation of small diameter TEVGs.

In vitro degradation of fibrous bilayer poly-L-lactic acid scaffolds

Polymer degradation and mechanical properties are of paramount importance in tissue engineering. The degradation rate of polymeric scaffolds is influenced by several important material and environmental factors. In particular, the mechanical support provided by the scaffold to the surrounding tissue during tissue regeneration is critical for that it directly impacts the cell behavior through mechanical signals sensed by mechanoreceptors on the cell surface. Consequently, the principal objective of the present study was to investigate the degradation behavior of electrospun poly-L-lactic acid (PLLA) bilayer microfibrous scaffolds in pH-neutral medium. Changes in the morphology, molecular weight, crystallinity, mass loss, and thermomechanical properties of the scaffolds over an extended period were studied by scanning electron microscopy, differential scanning calorimetry, gel permeation chromatography, and tensile testing. An interplay between chain scission and orderly chain rearrangement in the polymer scaffold commenced during degradation, leading to the decrease of the molecular weight and stiffness, a constant mass loss, and an increase in crystallinity, tensile strength, and glass transition temperature, with virtually constant yield strength and melting temperature. The unchanged structure morphology and adequate matrix stiffness after prolonged degradation illuminated the potential of the bilayer PLLA scaffolds for tissue engineering and drug delivery applications. Nonetheless, modifications to the scaffold structure or surface may be required to accordingly tune the degradation rate in these applications. The experimental methodology introduced in this study can be extended to potentially investigate material degradation in other fields, such as agriculture, packaging, and disposable products.

Introducing Metal–Organic Frameworks to Melt Electrowriting: Multifunctional Scaffolds with Controlled Microarchitecture for Tissue Engineering Applications

AbstractScaffolds with multiple advantageous biological and structural properties are still a challenge in the field of tissue engineering. The convergence of advanced fabrication techniques and functional materials is key to fulfill this need. Melt electrowriting (MEW) is an additive manufacturing technique that enables the fabrication of microfibrous scaffolds with precisely defined microarchitectures. Here, it is proposed to exploit metal–organic frameworks (MOFs) to efficiently introduce multifunctionalities by combining polycaprolactone (PCL), the gold standard material in MEW, with a silver‐/silver‐chloride‐decorated iron‐based MOF (NH2‐MIL‐88B(Fe)). This results in highly ordered constructs with antibacterial properties and magnetic resonance imaging (MRI) visibility. Scaffolds with up to 20 wt% MOF are successfully melt‐electrowritten with a fiber diameter of 50 µm. Among these, 5 wt% MOF proves to be the optimal concentration as it exhibits silver‐induced sustained antibacterial efficacy while maintaining PCL cytocompatibility and in vitro immune response. The iron component of the MOF (Fe(III) nodes) renders the composite visible with MRI, thereby enabling scaffold monitoring upon implantation with a clinically accepted method. The combination of MEW and MOFs as tunable additives and cargo carriers opens the way for designing advanced multifunctional scaffolds with a wide range of applications in, e.g., tissue engineering, biosensing and drug delivery.

Synthesis, Characterization, and Processing of Highly Bioadhesive Polyurethane Urea as a Microfibrous Scaffold Inspired by Mussels

Synthesis, Characterization, and Processing of Highly Bioadhesive Polyurethane Urea as a Microfibrous Scaffold Inspired by Mussels

Microfibrous Scaffolds Guide Stem Cell Lumenogenesis and Brain Organoid Engineering.

3D organoids are widely used as tractable in vitro models capable of elucidating aspects of human development and disease. However, the manual and low-throughput culture methods, coupled with a low reproducibility and geometric heterogeneity, restrict the scope and application of organoid research. Combining expertise from stem cell biology and bioengineering offers a promising approach to address some of these limitations. Here, melt electrospinning writing is used to generate tuneable grid scaffolds that can guide the self-organization of pluripotent stem cells into patterned arrays of embryoid bodies. Grid geometry is shown to be a key determinant of stem cell self-organization, guiding the position and size of emerging lumens via curvature-controlled tissue growth. Two distinct methods for culturing scaffold-grown embryoid bodies into either interconnected or spatially discrete cerebral organoids are reported. These scaffolds provide a high-throughput method to generate, culture, and analyze large numbers of organoids, substantially reducing the time investment and manual labor involved in conventional methods of organoid culture. It is anticipated that this methodological development will open up new opportunities for guiding pluripotent stem cell culture, studying lumenogenesis, and generating large numbers of uniform organoids for high-throughput screening.

Peripheral Nerve Regeneration at 1 Year: Biodegradable Polybutylene Succinate Artificial Scaffold vs. Conventional Epineurial Sutures.

The utilization of a planar poly(1,4-butylene succinate) (PBS) scaffold has been demonstrated as an effective approach for preserving nerve continuity and facilitating nerve regeneration. In this study, we assessed the characteristics of a microfibrous tubular scaffold specifically designed and fabricated through electrospinning, utilizing PBS as a biocompatible and biodegradable material. These scaffolds were evaluated as nerve guide conduits in a rat model of sciatic nerve neurotmesis, demonstrating both their biodegradability and efficacy in enhancing the reconstruction process over a long-term period (1-year follow-up). Histological assay and electrophysiological evaluation were performed to compare the long-term outcomes following sutureless repair with the microfibrillar wrap to outcomes obtained using traditional suture repair.

Plant-Based, Hydrogel-like Microfibers as an Antioxidant Platform for Skin Burn Healing.

Natural polymers from organic wastes have gained increasing attention in the biomedical field as resourceful second raw materials for the design of biomedical devices which can perform a specific bioactive function and eventually degrade without liberating toxic residues in the surroundings. In this context, patches and bandages, that need to support the skin wound healing process for a short amount of time to be then discarded, certainly constitute good candidates in our quest for a more environmentally friendly management. Here, we propose a plant-based microfibrous scaffold, loaded with vitamin C (VitC), a bioactive molecule which acts as a protecting agent against UV damages and as a wound healing promoter. Fibers were fabricated via electrospinning from various zein/pectin formulations, and subsequently cross-linked in the presence of Ca2+ to confer them a hydrogel-like behavior, which we exploited to tune both the drug release profile and the scaffold degradation. A comprehensive characterization of the physico-chemical properties of the zein/pectin/VitC scaffolds, either pristine or cross-linked, has been carried out, together with the bioactivity assessment with two representative skin cell populations (human dermal fibroblast cells and skin keratinocytes, HaCaT cells). Interestingly, col-1a gene expression of dermal fibroblasts increased after 3 days of growth in the presence of the microfiber extraction media, indicating that the released VitC was able to stimulate collagen mRNA production overtime. Antioxidant activity was analyzed on HaCaT cells via DCFH-DA assay, highlighting a fluorescence intensity decrease proportional to the amount of loaded VitC (down to 50 and 30%), confirming the protective effect of the matrices against oxidative stress. Finally, the most performing samples were selected for the in vivo test on a skin UVB-burn mouse model, where our constructs demonstrated to significantly reduce the inflammatory cytokines expression in the injured area (50% lower than the control), thus constituting a promising, environmentally sustainable alternative to skin patches.

Dual-bioactive molecules loaded aligned core-shell microfibers for tendon tissue engineering

Development of a controlled delivery ultrafine fibrous system with two bioactive molecules is required to stimulate tendon healing in different phase. In this study, we used emulsion stable jet electrospinning to fabricate aligned poly(L-lactic acid) (PLLA) based ultrafine fibers with two small bioactive molecules of L-Arginine (Arg) and low molecular weight hyaluronic acid (HA). The results demonstrated that the aligned Arg/HA/PLLA microfibrous scaffold showed core-shell structure and allowed sequential release of Arg and HA due to their different electric charge. The scaffold also showed enhanced hydrophilicity, cell migration, spread and proliferation. Using an Achilles tendon repair model in rats, we demonstrated that this novel fibrous scaffold can prevent adhesion and promote tendon regeneration. Additionally, two p53 and ER-α-mediated signalling pathways were described as the probable main path of synergistic effects of the novel scaffold on tendon generation. Thus, this study may provide an important strategy for developing biofunctional and biomimetic tendon scaffolds.

Electrically Triggered Quercetin Release from Polycaprolactone/Bismuth Ferrite Microfibrous Scaffold for Skeletal Muscle Tissue.

Skeletal muscle tissue engineering presents a promising avenue to address the limitations pertaining to the regenerative potential of stem cells in case of injury or damage. The objective of this research was to evaluate the effects of utilizing novel microfibrous scaffolds, containing the compound quercetin (Q), on skeletal muscle regeneration. Morphological test results showed us that the combination of bismuth ferrite (BFO), polycaprolactone (PCL), and Q were bonded and well-ordered with each other, and a uniform microfibrous structure was obtained. Antimicrobial susceptibility testing of PCL/BFO/Q was conducted, and microbial reduction was found to be over 90% in the highest concentration of Q-loaded microfibrous scaffolds with the most inhibitory effect on S. aureus strains. Further, biocompatibility was investigated by performing MTT testing, fluorescence testing, and SEM imaging on mesenchymal stem cells (MSCs) to determine whether they could act as suitable microfibrous scaffolds for skeletal muscle tissue engineering. Incremental changes in the concentration of Q led to increased strength and strain, allowing muscles to withstand stretching during the healing process. In addition, electrically conductive microfibrous scaffolds enhanced the drug release capability by revealing that Q can be released significantly more quickly by applying the appropriate electric field, compared with conventional drug-release techniques. These findings suggest a possible use for PCL/BFO/Q microfibrous scaffolds in skeletal muscle regeneration by demonstrating that the combined action of both guidance biomaterials was more successful than Q itself acting alone.

Reduced Fibroblast Activation on Electrospun Polycaprolactone Scaffolds.

In vivo, quiescent fibroblasts reside in three-dimensional connective tissues and are activated in response to tissue injury before proliferating rapidly and becoming migratory and contractile myofibroblasts. When deregulated, chronic activation drives fibrotic disease. Fibroblasts cultured on stiff 2D surfaces display a partially activated phenotype, whilst many 3D environments limit fibroblast activation. Cell mechanotransduction, spreading, polarity, and integrin expression are controlled by material mechanical properties and micro-architecture. Between 3D culture systems, these features are highly variable, and the challenge of controlling individual properties without altering others has led to an inconsistent picture of fibroblast behaviour. Electrospinning offers greater control of mechanical properties and microarchitecture making it a valuable model to study fibroblast activation behaviour in vitro. Here, we present a comprehensive characterisation of the activation traits of human oral fibroblasts grown on a microfibrous scaffold composed of electrospun polycaprolactone. After over 7 days in the culture, we observed a reduction in proliferation rates compared to cells cultured in 2D, with low KI67 expression and no evidence of cellular senescence. A-SMA mRNA levels fell, and the expression of ECM protein-coding genes also decreased. Electrospun fibrous scaffolds, therefore, represent a tuneable platform to investigate the mechanisms of fibroblast activation and their roles in fibrotic disease.