Microbore Column Research Articles

Microbore-based vacuum jacketed liquid chromatography for fast, efficient and sustainable high throughput bioanalysis

Extra-column band broadening can significantly reduce the performance of rapid ultra-high performance liquid chromatography-MS-based methods (UHPLC-MS). However, as we show here, UHPLC-MS/MS methods on short 2.1 mm i.d. columns can be optimized to reduce band broadening by simple procedures such as dispensing with the solvent divert valves placed between the column and the MS source. Vacuum jacketed columns have previously been shown to provide superior performance to conventional UHPLC-MS/MS by reducing on and post column band broadening. Here we have compared the optimized “direct” UHPLC approach for the high throughput (HT) bioanalysis of drugs and metabolites in biofluids such as urine and blood plasma with vacuum jacketed chromatography (VJC), using columns of the same geometry and packed with the same stationary phases. This study demonstrates that the performance of VJC was still superior to the direct UHPLC-MS/MS methods for rapid “generic” bioanalysis using gradient times of 0.25 to 5 min. Further investigations using microbore VJC-MS/MS, with 1 mm i.d. columns, for bioanalysis of the same biofluid samples showed that this format offers great promise for HT “discovery” drug and metabolite analysis/profiling. In addition the reduction of solvent use, by up to 90 % for methods when using microbore columns, can significantly contribute to improved sustainability and reducing costs per analysis.

Automated sample preparation and fast GC-MS determination of fatty acids in blood samples and dietary supplements.

The present research is focused on the optimization of an automatized sample preparation and fast gas chromatography-mass spectrometry (GC-MS) method for the analysis of fatty acid methyl esters (FAMEs) in blood samples and dietary supplements, with the primary objective being a significant reduction of the analysis time and, hence, an enhanced sample throughput. The mass spectrometer was operated in the scan/selected ion monitoring (SIM) acquisition method, thus enabling the obtainment of qualitative and (highly sensitive) quantitative data. The separation of FAMEs was obtained in about 11min by using a micro-bore column of dimensions 15m × 0.10mm ID × 0.10µm df with a polyethylene glycol stationary phase. The novelty of the research involves reducing analysis time by using the novel fast GC-MS method with increased identification reliability and sensitivity in a single chromatographic run. With regard to the figures of merit, linearity, accuracy, and limits of detection (LoD) and quantification (LoQ) were determined. Specifically, regression coefficients were between 0.9901 and 0.9996; the LoDs ranged from 0.05 to 1.02µgg-1 for the blood analysis method, and from 0.05 to 0.26mgg-1 in the case of the dietary supplement approach. With respect to LoQs, the values were in the ranges of 0.15-3.39µgg-1 and 0.15-0.86mgg-1 for blood and dietary supplements analysis methods, respectively. Accuracy was evaluated by analyzing certified reference materials (human plasma, fish oil).

Comparison of the separation of proteins of wide-ranging molecular weight via trilobal polypropylene capillary-channeled polymer fiber, commercial superficiously porous, and commercial size exclusion columns.

Reversed phase and size-exclusion chromatography methods are commonly used for protein separations, although they are based on distinctly different principles. Reversed phase methods yield hydrophobicity-based (loosely-termed) separation of proteins on porous supports, but tend to be limited to proteins with modest molecular weights based on mass transfer limitations. Alternatively, size-exclusion provides complementary benefits in the separation of higher mass proteins based on entropic, not enthalpic, processes, but tend to yield limited peak capacities. In this study, microbore columns packed with a novel trilobal polypropylene capillary-channeled polymer fiber were used in a reversed phase modality for the separation of polypeptides and proteins of molecular weights ranging from 1.4 to 660kDa. Chromatographic parameters including gradient times, flow rates, and trifluoroacetic acid concentrations in the mobile phase were optimized to maximize resolution and throughput. Following optimization, the performance of the trilobal fiber column was compared to two commercial-sourced columns, a superficially porous C4-derivatized silica and size exclusion, both of which are sold specifically for protein separations and operated according to the manufacturer-specified conditions. In comparison to the commercial columns, the fiber-based column yielded better separation performance across the entirety of the suite, at much lower cost and shorter separation times.

Simultaneous determination of nicotinamide and N1 -methylnicotinamide in human serum by LC-MS/MS to associate their serum concentrations with obesity.

A rapid and sensitive LC-MS/MS method was developed and validated for the simultaneous determination of nicotinamide and its metabolite N1 -methylnicotinamide in human serum. Serum samples were prepared by protein precipitation with acetonitrile. The chromatographic separation was performed on a Waters Spherisorb S5 CN microbore column (2.0 × 100 mm, 5μm) with gradient elution within 7min. Acetonitrile and 5mm ammonium formate aqueous solution (containing 0.1% formic acid) were used as mobile phases. Nicotinamide, N1 -methylnicotinamide and N'-methylnicotinamide (internal standard) were detected with a triple-quadrupole tandem mass spectrometer in the positive ion mode. Multiple reaction monitoring was used to monitor precursor to product ion transitions of m/z 123.1 → 80.1 for nicotinamide, m/z 137.1 → 94.1 for N1 -methylnicotinamide and m/z 137.1 → 80.1 for the internal standard. The linear ranges of nicotinamide and N1 -methylnicotinamide were 5.000-160.0and 2.500-80.00 ng/ml, respectively. The intra- and inter-day precisions (RSD) of both analytes were within 6.90%. The recoveries were >88%. The analytes were proven to be stable during all sample storage, preparation and analytic procedures. The method was successfully applied to determine the concentrations of nicotinamide and N1 -methylnicotinamide in human serum to investigate the association between their concentrations and obesity in 1160 Chinese subjects.

Extraction of intrinsic column peak profiles of narrow-bore and microbore columns by peak deconvolution methods

The intrinsic peak profiles (free from the delay and dispersion caused by state-of-the art UHPLC systems) generated by narrow-bore and microbore chromatographic columns used in liquid chromatography-mass spectrometry (LC-MS) proteomic analyses are extracted from two different deconvolution methods. The first method is based on the classical discrete Fourier transform (DFT) while the second method refers to the Taylor expansion of the continuous Fourier transform (FT). The two numerical methods are compared regarding the accurate determination of the intrinsic peak profiles of the non-retained compound (toluene) expected on a narrow-bore 2.1 mm × 100 mm column packed with 1.6 μm CORTECS-C18 superficially porous particles and installed on three different LC systems (ACQUITY i-class UPLC, ACQUITY H-class UPLC, and Arc LC systems). The DFT-based method is most relevant when the low-frequency band of the chromatographic peak does not overlap with the high-frequency bands related to the experimental baseline noise (pump/detector). The Taylor expansion-based method is successful for the extraction of the intrinsic peak profiles of narrow-bore 2.1 mm i.d. columns packed with sub-2 μm particles installed on standard UHPLC systems. When the LC system dispersion significantly exceeds that of the column, the DFT-based method is preferred over the Taylor expansion-based method and is successfully applied to extract the intrinsic peak profiles generated by a microbore 1.0 mm × 100 mm column packed with 1.8 μm HSS-C18 fully porous particles (volume variance ∼ 0.15 μL2 for the non-retained compound toluene) run on the low-dispersion ACQUITY i-class UPLC system (∼ 1 μL2 volume variance). This result opens up promising avenues for the development, quality control, and LC-MS analyses of microbore 1 mm i.d. columns using the state-of-the-art UHPLC instruments at flow rates larger than 0.1 mL/min.

Using 1.5 mm internal diameter columns for optimal compatibility with current liquid chromatographic systems

This article describes the use of a new prototype column hardware made with 1.5 mm internal diameter (i.d.) and demonstrates some benefits over the 1.0 mm i.d. micro-bore column. The performance of 2.1, 1.5 and 1.0 mm i.d. columns were systematically compared. With the 1.5 mm i.d. column, the loss of apparent column efficiency can be significantly reduced compared to 1.0 mm i.d. columns in both isocratic and gradient elution modes. In the end, the 1.5 mm i.d. column is almost comparable to 2.1 mm i.d. column from a peak broadening point of view. The advantages of the 1.5 mm i.d. hardware vs 2.1 mm i.d. narrow-bore columns are the lower sample and solvent consumption, and reduced frictional heating effects due to decreased operating flow rates.

The influence of injection volume on efficiency of microbore liquid chromatography columns for gradient and isocratic elution

The injection volume and the associated column volume overload is one of the most common issues in miniaturized chromatography. The injection volume should not exceed 10% of the effective column volume. A further reduction of the injection volume leads to an increase in chromatographic efficiency. However, the signal intensity must be above a certain threshold to generate a chromatographic peak that can be detected. Therefore, the injection volume has to be optimized to reach the ideal balance between chromatographic efficiency and sensitivity. This study examined the general influence of the injection volume for both isocratic and gradient elution, depending on the retention factor and peak standard deviation. For this purpose, substances of different polarity were selected to represent a broad elution spectrum. Besides the model analyte naphthalene, these were mainly pharmaceuticals. For all measurements a microbore column with an ID of 300 µm and packed with 1.9 μm fully porous particles was used. For isocratic elution, the injection volume was varied between 4 and 16% of the effective column volume. The retention factors were adjusted between 2 and 10. For gradient elution, the injection volume was varied between 4 and 160% of the effective column volume. The observed effects were further investigated using the gradient kinetic plot theory. In isocratic elution, a loss in plate height up to 50% was observed for components that elute near the void time. A significant reduction of the chromatographic efficiency was noticed up to a retention factor of 4. In gradient elution, a reduction in peak capacity could only be observed if the injection volume exceeded 40% of the effective column volume. For some substances, only a slight loss in peak capacity was noticed even with a volume overload of 160%.

Metabolic Phenotyping Using UPLC\u2013MS and Rapid Microbore UPLC\u2013IM\u2013MS: Determination of the Effect of Different Dietary Regimes on the Urinary Metabolome of the Rat

A rapid reversed-phase gradient method employing a 50 mm × 1 mm i.d., C18 microbore column, combined with ion mobility and high-resolution mass spectrometry, was applied to the metabolic phenotyping of urine samples obtained from rats receiving different diets. This method was directly compared to a “conventional” method employing a 150 × 2.1 mm i.d. column packed with the same C18 bonded phase using the same samples. Multivariate statistical analysis of the resulting data showed similar class discrimination for both microbore and conventional methods, despite the detection of fewer mass/retention time features by the former. Multivariate statistical analysis highlighted a number of ions that represented diet-specific markers in the samples. Several of these were then identified using the combination of mass, ion-mobility-derived collision cross section and retention time including N-acetylglutamate, urocanic acid, and xanthurenic acid. Kynurenic acid was tentatively identified based on mass and ion mobility data.

Application of polydopamine-coated nylon capillary-channeled polymer fibers as a stationary phase for mass spectrometric phosphopeptide analysis.

Capillary-channeled polymer (C-CP) fibers are demonstrated as a selective stationary phase for phosphopeptide analysis via LC-MS. Taking advantage of the oxidative self-polymerization of dopamine under alkaline conditions, a simple system involving a dilute aqueous solution of 0.2% w/v dopamine hydrochloride in 0.15% w/v TRIS buffer, pH 8.5 was utilized to coat polydopamine onto nylon 6 C-CP fibers. Confirmation of the polydopamine coating on the fibers (nylon-PDA) was made through attenuated total reflection-FTIR (ATR-FTIR) analysis. Imaging using SEM was also performed to examine the morphology and topography of the nylon-PDA. Subsequent loading of Fe3+ to the nylon-PDA matrix was confirmed by SEM/energy dispersive X-ray spectroscopy (SEM/EDX). The Fe3+ -bound nylon-PDA fibers packed in a microbore column format were tested in the off-line preconcentration of phosphopeptides from a 1:100 mixture of β-casein/BSA digests for MALDI-TOF analysis. The packed column was also installed onto an HPLC system as a platform for the online sample clean-up and enrichment of phosphopeptides from a 1:1000 mixture of β-casein/BSA protein digests that were determined by subsequent ESI-MS analysis.

Track-etched membrane-based dual-electrode coulometric detector for microbore/capillary high-performance liquid chromatography

The electrochemical flow cell containing track-etched microporous membrane electrodes was applied to a dual-electrode coulometric detector for microbore/capillary HPLC with a small injection volume and low eluent flow rate. The proposed flow cell with a 0.1-mm diameter inlet channel gave a detection volume of 0.08 nL per electrode, which was determined by the eluent flow through the electrode. For the dual-electrode detector, the calculated volume was 0.24 nL. The efficiency of electrooxidation of l-ascorbic acid increased as the flow rate decreased and was close to 100% when the flow rate was below 50 μL min−1, which is a common flow rate in microbore or capillary liquid chromatography. Catecholamines, such as noradrenaline, adrenaline, and dopamine, were detected by total conversion with two-electron oxidation in the potential range from 0.8 to 1.0 V vs. Ag/AgCl after separation with a microbore column. These peaks were accompanied by corresponding cathodic peaks derived from quasi-stable electrooxidation products of the catecholamines. The detection limits of noradrenaline, adrenaline, and dopamine were 0.1, 0.1, and 0.2 μM, respectively. The RSD values for five replicate measurements of 5.0 μM of these compounds were 0.9%, 0.7%, and 1.5%, respectively. Coulometric detection was also demonstrated by determination of catecholamines in pharmaceuticals.

Detection of recombinant insulins in human urine by liquid chromatography-electrospray ionization tandem mass spectrometry after immunoaffinity purification based on monolithic microcolumns.

This work describes an analytical procedure based on automated affinity purification followed by liquid chromatography-electrospray tandem mass spectrometry with a conventional triple quadrupole analyzer, in order to detect synthetic insulins (Apidra®, Humalog®, Levemir®, NovoRapid®, and Tresiba®) in human urine. Sample preparation included ultrafiltration followed by immunoaffinity purification on monolithic microcolumns. Chromatographic separation was performed by a C18 microbore column, while mass spectrometric identification of the analytes was achieved by a triple quadrupole mass spectrometer under positive ion electrospray ionization and acquisition mode in selected reaction monitoring. Identification of the synthetic insulins was performed by selecting at least two characteristic ion transitions for each analyte. The newly developed method was validated in terms of specificity, recovery, matrix effect, sensitivity, robustness, and repeatability of retention times and relative ion transition abundance. The specificity and the reproducibility of the relative retention times and the relative abundance of the characteristic ion transitions selected was confirmed to be fit for purposes of ensuring the unambiguous identification of all target analytes, also in the forensic field. The extraction yield was estimated at greater than 60% and the matrix effect smaller than 35%. The lower limits of detection were in the range of 0.02-0.05ng/mL, proving the method to be sufficiently sensitive to detect the abuse of insulins in cases where they are used as performance-enhancing agents in sport. The applicability of the developed method was assessed by the analysis of urine samples obtained from diabetic subjects treated with Tresiba® and/or Humalog®, whose presence was confirmed in urine samples collected after the administration of therapeutic doses. Graphical abstract A hybrid assay comprising MSIA-based immunoextraction combined with liquid chromatography-electrospray tandem mass spectrometry was developed and validated for the detection of recombinant insulins in human urine.

Influence of photo-initiators in the preparation of methacrylate monoliths into poly(ethylene-co-tetrafluoroethylene) tubing for microbore HPLC

In this study, poly(butyl methacrylate-co-ethyleneglycol dimethacrylate) polymeric monoliths were in situ developed within 0.75 mm i.d. poly(ethylene-co-tetrafluoroethylene) (ETFE) tubing by UV polymerization via three different free-radical initiators (α,α’-azobisisobutyronitrile (AIBN), 2,2-dimethoxy-2-phenylacetophenone (DMPA) and 2-methyl-4′-(methylthio)-2-morpholinopropiophenone (MTMPP). The influence of the nature of each photo-initiator and irradiation time on the morphological features of the polymer was investigated by scanning electron microscopy, and the chromatographic properties of the resulting microbore columns were evaluated using alkyl benzenes as test substances. The beds photo-initiated with MTMPP gave the best performance (minimum plate heights of 38 μm for alkyl benzenes) and exhibited a satisfactory reproducibility in the chromatographic parameters (RSD < 11%). These monolithic columns were also successfully applied to the separation of phenylurea herbicides, proteins and a tryptic digest of β-casein.

Preparation and characterization of micro-bore wall-coated open-tubular capillaries with low phase ratios for fast-gas chromatography–mass spectrometry: Application to ignitable liquids and fire debris

Fast Gas Chromatography (GC) allows for analysis times that are a fraction of those seen in traditional capillary GC. Key modifications in fast GC include using narrow, highly efficient columns that can resolve mixtures using a shorter column length. Hence, a typical fast GC column has an inner diameter of 100–180 μm. However, to maintain phase ratios that are consistent with typical GC columns, the film thickness of fast GC stationary phases are also low (e.g., 0.1–0.18 μm). Unfortunately, decreased film thickness leads to columns with very low sample capacity and asymmetric peaks for analytes that are not sufficiently dilute. This paper describes micro-bore (50 μm i.d.) capillary columns with thick films (1.25 μm), and low phase ratios (10). These columns have greater sample capacity yet also achieve minimum plate heights as low as 110 μm. Hence, separation efficiency is much higher than would be obtained using standard GC columns. The capillary columns were prepared in-house using a simple static-coating procedure and their plate counts were determined under isothermal conditions. The columns were then evaluated using temperature programming for fast GC–MS analysis of ignitable liquids and their residues on fire debris exemplars. Temperature ramps of up to 75 °C min−1 could be used and separations of ignitable liquids such as gasoline, E85 fuel, and lighter fluid (a medium petroleum distillate) were complete within 3 min. Lastly, simulated fire debris consisting of ignitable liquids burned on carpeting were extracted using passive headspace absorption-elution and the residues successfully classified.

Determination of the polyphenolic fraction of Pistacia vera L. kernel extracts by comprehensive two-dimensional liquid chromatography coupled to mass spectrometry detection.

Pistachio (Pistacia vera L.) belongs to the Anacardiaceae family and it is a small tree species. It is native of the Middle East and Central Asia, but currently, it is cultivated also in California and in some Mediterranean countries, such as Greece and Italy. The most important pistachio producers are Iran, the USA, and Turkey. Besides being a delicious nut, pistachio, due to its wholesome nutritional properties, could be considered as a functional food. According to the results of several studies, pistachios have been proven to have various groups of valuable phytochemicals such as anthocyanins, flavan-3-ols, proanthocyanidins, flavonols, isoflavones, flavanones, stilbenes, and phenolic acids, possessing excellent biological activities. The most common analytical technique employed for their analysis is represented by liquid chromatography coupled to photodiode array and mass spectrometry detection. However, conventional LC can present some limits especially in terms of resolving power. In this contribution, as a powerful alternative, comprehensive two-dimensional liquid chromatography (LC×LC) was applied to the determination of the polyphenolic fraction of pistachio kernels from different geographical origins. A 150-mm micro-bore cyano column (2.7μm dp) and 50-mm superficially porous C18 silica column (2.7μm dp) in the first (1D) and second (2D) dimensions were employed, respectively. For boosting orthogonality, a shift 2D gradient was investigated leading to an increase in the overall peak capacity. The newly developed LC×LC method showed satisfactory linearity, sensitivity, precision and accuracy, which was then applied to sample quantitative analysis. A total of 51 different polyphenolic compounds were determined in the four samples investigated and 18 out of them are hereby reported for the first time.

Collection and identification of an unknown component from Eugenia uniflora essential oil exploiting a multidimensional preparative three-GC system employing apolar, mid-polar and ionic liquid stationary phases.

The present research deals with the collection and structural elucidation of an unknown component, accounting for about 35% of the essential oil obtained upon distillation of the leaves of Eugenia uniflora L., harvested during summer (January, 2017) in Paraná State (Southern Brazil). A multidimensional gas chromatographic preparative system, based on the coupling of three GC systems equipped with apolar, PEG and ionic liquid-based stationary phases, was successfully applied for the isolation of the chromatographic band relative to the unknown molecule. The use of wide-bore columns allowed for an increased sample capacity compared to conventional micro-bore columns, thus the injection of a neat sample was feasible, greatly reducing the total collection time. A higher chromatographic efficiency was afforded by the use of a multidimensional approach in the heart-cut mode, exploiting the different selectivity of three stationary phases, which ensured the attainment of a highly pure fraction. In only five runs, more than 3 milligrams were collected, with an average purity greater then 95%. Finally, the unknown component was subjected to nuclear magnetic resonance spectroscopy, mass spectrometry and condensed phase Fourier-transform infrared spectroscopy, leading to the identification of 6-ethenyl-6-methyl-3,5-di(prop-1-en-2-yl)cyclohex-2-en-1-one. The presented approach has been demonstrated to be effective for the isolation and structural elucidation of unknown molecules in complex samples, which will allow for further in-depth studies, like biological evaluation or pharmacological tests.

Comprehensive two-dimensional monolithic liquid chromatography of polar compounds.

Two-dimensional liquid chromatography largely increases the number of separated compounds in a single run, theoretically up to the product of the peaks separated in each dimension on the columns with different selectivities. On-line coupling of a reversed-phase column with an aqueous normal-phase (hydrophilic interaction liquid chromatography) column yields orthogonal systems with high peak capacities. Fast on-line two-dimensional liquid chromatography needs a capillary or micro-bore column providing low-volume effluent fractions transferred to a short efficient second-dimension column for separation at a high mobile phase flow rate. We prepared polymethacrylate zwitterionic monolithic micro-columns in fused silica capillaries with structurally different dimethacrylate cross-linkers. The columns provide dual retention mechanism (hydrophilic interaction and reversed-phase). Setting the mobile phase composition allows adjusting the separation selectivity for various polar substance classes. Coupling on-line an organic polymer monolithic capillary column in the first dimension with a short silica-based monolithic column in the second dimension provides two-dimensional liquid chromatography systems with high peak capacities. The silica monolithic C18 columns provide higher separation efficiency than the particle-packed columns at the flow rates as high as 5mL/min used in the second dimension. Decreasing the diameter of the silica monolithic columns allows using a higher flow rate at the maximum operation pressure and lower fraction volumes transferred from the first, hydrophilic interaction dimension, into the second, reversed-phase mode, avoiding the mobile phase compatibility issues, improving the resolution, increasing the peak capacity, and the peak production rate.

Mass Spectrometric Amino Acid Sequencing of Short and Mid-Sized Peptides in a ESI-O-TOF System as an Alternative to MS/MS: I. Selective Fragmentation of Peptides with y-Ion Formation

The possibility of mass spectrometric sequencing of peptides without the need for the conventional MS/MS analysis has been demonstrated experimentally. The peptide hydrolysate was fractionated by reversephase chromatography on a microbore column. The eluate fraction was injected into the mass spectrometer via an electrospray ion source that directly coupled a liquid chromatography instrument to a time-of-flight mass spectrometer (HPLC-MS). Fragmentation of the peptides eluted from the column was performed in the mass spectrometer interface by varying the voltage difference between the mass spectrometer nozzle and skimmer. A restricted set of intensive peaks of y-ions, which corresponded to sequential cleavage of all amino acids from the peptide, was obtained. The ratios of the y-ion peak intensities to the background were (5−100)/1. The presence of Lys and Arg in the peptides provided for a substantial increase of informative peak intensity in the mass spectra. The mass spectra of short peptides (up to 10 residues) were processed manually, whereas the Proteos hardware and software system was used to process the fragmentation results for a long N-terminal peptide of the human hemoglobin α-chain.

Static Headspace Analysis Using Low-Pressure Gas Chromatography and Mass Spectrometry, Application to Determining Multiple Partition Coefficients: A Practical Tool for Understanding Red Wine Fruity Volatile Perception and the Sensory Impact of Higher Alcohols.

To evaluate the partition coefficients of volatiles between the liquid and gas phases, an analytical method was developed and optimized using static headspace analysis and low-pressure injection gas chromatography coupled to mass spectrometry (SHS-LP-GC/MS). Two different types of analytical columns were coupled for low-pressure chromatography injection: a narrow restriction microbore column on the inlet side and a mega-bore column on the mass spectrometer side. Coupling these two columns and static headspace analysis to gas chromatography and mass spectrometry resulted in a simple, fast, sensitive, and accurate approach. Several points have been optimized: time to reach the thermodynamic equilibrium in the gas phase, syringe filling rate, gas injection rate, and volume ratio between the gas and liquid phases. This new method was used to determine partition coefficients between the liquid and gas phases and study multicomponent mixtures for which particular perceptive interactions had previously been highlighted. The partition coefficients of 9 esters and 5 higher alcohols were determined in dilute alcohol solution (12% v/v) and dearomatized red wine. These partition coefficients revealed modifications in ester headspace release in the presence of higher alcohols for the first time in this type of matrix. The correlation of these results with sensory data highlighted the role of physicochemical, presensory effects on sensory modifications for the first time, suggesting that this type of interaction may partly modulate qualitative and quantitative fruity perception.

Characterization of Klason lignin samples isolated from beech and aspen using microbore column size-exclusion chromatography.

The present study is focused on the separation and characterization of lignin samples isolated by Klason method from European beech (Fagus sylvatica) broadleaf hardwood and European aspen (Populus tremula) broadleaf softwood by size-exclusion chromatography. The separation was carried out using dimethylformamide as major component of the mobile phase and a 3mm id microbore column packed with hydroxyethyl methacrylate gel, calibrated with polystyrene standards. The influence of mobile phase composition and sample solvent composition on the chromatographic behavior and molar mass distributions was investigated.

Cryogenic modulation fast GC × GC-MS using a 10m microbore column combination: Concept, method optimization, and application.

The present research is based on the concept of using a 10m × 0.1mm id column for cryogenic-modulation fast comprehensive two-dimensional gas chromatography with quadrupole mass spectrometry. Specifically, an 8.9m × 0.1mm id low-polarity column was used as the first dimension, and a 1.1m × 0.1mm id medium-polarity column was used as the second dimension. The main scope of the investigation was to develop a high peak-capacity method, with an analysis time of approximately 10min. Various aspects related to method optimization are discussed, as well as separation parameters such as peak capacity (in each dimension, and as a total value), first-dimension sample capacity, peak widths, modulation ratio, sensitivity enhancement, and number of spectra per peak. The fast approach was evaluated in applications involving a mixture of cosmetic allergens and a sample of perfume. The approach proposed enables high-resolution separations in a short time (across the C8 -C23 alkane range), as well as a considerable reduction of the consumption of gases for modulation cooling and heating.