Μg Cm-2 Research Articles

Potential-Dependent ATR-SEIRAS and EQCM-D Analysis of Interphase Formation in Zinc Battery Electrolytes.

With the heightening interest in bivalent battery technology, there arises a necessity for a thorough investigation into zinc-ion battery (ZIB) electrolytes, accommodating their chemical attributes and potential-dependent structural dynamics. While the phenomenon of in situ solid electrolyte interphase formation is extensively documented in lithium-ion batteries, its analogous occurrences in ZIBs remain limited. Herein is a comparative study of three zinc electrolytes of interest: ZnSO4, ZnOTF, and Zn(TFSI)2/LiTFSI hybrid water-in-salt electrolyte. Additionally, the impact of an acetonitrile additive is scrutinized, with a comparative assessment of the interfacial behavior in aqueous solutions. Utilizing ATR-SEIRAS, potential-dependent alterations in the composition of the electrolyte/electrode interface were monitored, while EQCM-D facilitated a comprehensive understanding of variations in the mass and structural properties of the adsorbed layer. Aqueous ZnSO4 demonstrated the accumulation of porous Zn4SO4(OH)6·xH2O at negative potentials, leading to a mass of 1.47 μg cm-2 after five cycles. Bisulfate formation was observed at positive potentials. SEIRAS measurements for ZnOTF demonstrated reorientation and surface adsorption of CF3SO3- to favor CF3 at the surface for positive potentials, and acetonitrile showed increased stability for the electrode at negative potentials. The additive was also reported to lead to the accumulation of a substantial passivation layer with viscoelastic properties. The zinc water-in-salt showed exceptional surface stability at negative potentials and a widened potential window. A thin rigid zinc SEI layer is reported with a mass of 0.7 μg cm-2. The compositional intricacies of these surface structures are discussed in relation to their solvent conditions. This investigation not only sheds light on the initial charge/discharge cycles in ZIBs but also underscores their pivotal role in instigating enduring transformations that can significantly influence their long-term cycling performance.

Hydroxypropyl methylcellulose stabilized clove oil nanoemulsified orodispersible films: Study of physicochemical properties, release profile, mucosal permeation, and anti-bacterial activity.

Hydroxypropyl methylcellulose (HPMC)-based nanoemulsions for quick dissolving orodispersible (OD) films were prepared to encapsulate clove oil (CO) to harness its anti-bacterial properties. The influence of additives maltodextrin, pectin, and glycerol on the OD films was studied. The nanoemulsion particle size varied from 135 nm to 195 nm. A decrease in tensile strength and, an increase in elongation at break and opacity were observed in OD films compared to neat HPMC film. The AFM images showed an increase in HPMC films' average roughness from 6.95 to 90 nm after adding CO and additives. The additives controlled CO in-vitro release from HPMC following the Higuchi model. The ex-vivo permeation through porcine mucosal membrane was 9-33 % while the permeation coefficient and flux were 0.282-0.879 cm s-1 and 0.191-1.318 μg cm-2 s-1, respectively. The OD films exhibited significant inhibition of Staphylococcus aureus, Streptococcus mutans, and Porphyromonas gingivalis suggesting their therapeutic potential in oral healthcare.

Spectrophotometric determination of metoclopramide hydrochloride in pharmaceutical tablets, by diazotization-coupling method with 1-naphthol as the coupling agent

Simple, rapid and sensitive spectrophotometric method was proposed for the analysis of metoclopramide hydrochloride (MPH) in pure form as well as in pharmaceutical tablets. The method is based on the diazotization reaction of MPH with sodium nitrite in hydrochloric acid medium to form diazonium salt, which is coupled with 1-naphthol in sodium hydroxide medium to form azo dye, showing absorption maxima at 550 nm. Beer’s law is obeyed in the concentration range of 0.4 – 18 µg mL-1 of MPH with detection limit 0.5448 µg mL-1. The molar absorptivity and Sandell’s sensitivity are 3.4969 × 104 L mol-1 cm-1 and 0.0101 µg cm-2, respectively. The method was successfully applied to the determination of MPH in pharmaceutical tablets without any interference from common excipients used as additives in tablets. The results agree favorably with the official British Pharmacopoeia method.

Boosting the bifunctional catalytic activity of Co3O4 on silver and nickel substrates for the alkaline oxygen evolution and reduction reactions

Developing an efficient bifunctional catalyst for oxygen reduction (ORR) and evolution reactions (OER) is a crucial step for the wide commercialization of alkaline water electrolyzers. However, a proper assessment and comparison of various catalysts is still challenging due to the different catalyst substrates and loadings. In this work, Co3O4 spinel nanoparticles (NPs) were investigated as a bifunctional catalyst at different substrates of glassy carbon or Ag bulk substrate or Ni particles and with different loadings. For Co3O4 (800 µg cm-2)/Ag electrode, not only the overpotential for ORR was 50 mV lower than the bare Ag electrode, but also the OER overpotential was 40 mV lower than the sole Co3O4. Besides, less than 1% peroxide intermediate was detected during ORR using the rotating ring disc electrode (RRDE) method, suggesting a 4-electron O2 reduction. Tafel slopes of 70 and 60 mV dec‑1 at Co3O4/Ag were obtained for ORR and OER, respectively. The improved bifunctional activity could be attributed to a synergistic effect between Co3O4 and the Ag support. For the loading effect, it is revealed that the number of accessible sites of Ag surface decreases with increasing the Co3O4 loading, as evaluated from lead-underpotential deposition measurements. Interestingly, after running ORR/OER cycles, the surface area increased by 4–6 times. This surface roughening was also confirmed by SEM and EDX. The study was extended to Co3O4+Ni mixed catalyst to validate the effect of the support on this induced synergism. Hence, this work provides a simple route for designing potential effective catalytic interfaces and contributes to unravelling the influence of the substrate and loading on the catalyst activity for water electrolyzers.

Quantification of Airborne Particulate Matter and Trace Element Deposition on Hedera helix and Senecio cineraria Leaves.

In both developed and developing countries, atmospheric pollution with particulate matter (PM) remains an important issue. Despite the health effects of poor air quality, studies on air pollution are often limited by the high costs of continuous monitoring and the need for extensive sampling. Furthermore, these particles are often enriched with potentially toxic trace elements and organic pollutants. This study evaluates both the composition of atmospheric dust accumulated during a certain timespan on Hedera helix and Senecio cineraria leaves and the potential for their use as bio-monitors. The test plants were positioned near automatic air quality monitoring stations at four different sites with respectively high, moderate and low traffic intensity. The gravimetric deposition of PM10 and PM2.5 on leaves was compared with data recorded by the monitoring stations and related to the weather conditions reported by Argentina's National Meteorological Service. To determine the presence of trace elements enriching the PM deposited on leaves, two analytical techniques were applied: XRF (not destructive) and ICP (destructive). The results indicated that only in the unpaved street location (site 2) did PM10 and PM2.5 concentrations (90 µg m-3 and 9 µg m-3) in the air exceed more than five times WHO guidelines (15 µg m-3 and 5 µg m-3). However, several trace elements were found to be enriching PM deposited on leaves from all sites. Predominantly, increased concentrations of Cd, Cu, Ti, Mn, Zn and Fe were found, which were associated with construction, traffic and unpaved street sources. Furthermore, based on its capability to sequester above 2800 µg cm-2 of PM10, 2450 µg cm-2 of PM2.5 and trace elements, Senecio cineraria can be taken into consideration for adoption as a bio-monitor or even for PM mitigation.

Bimetallic Ir-Ru 25:75 Catalyst for PEM-WE: Uncovering the Origin of Its Activity by Operando Wide Angle X-Ray Scattering

Proton Exchange Membrane Water Electrolyzers (PEM-WEs) are entering the phase of commercial mass production. However, the issue of an iridium catalyst for the anode remains. Our previous work presented an iridium-ruthenium-based catalyst (25% Ir = 158 µg cm-2, 75% Ru) prepared as a thin film on the surface-enhanced PEM-WE-anode via magnetron sputtering. This catalyst demonstrated excellent activity and stability in single-cell PEM-WE (1 A cm-2 at 1.606 V, 80 °C, degradation rate – 1.3 µV h-1 at 1 A cm-2 for 500 hours). The origin of its outstanding electrochemical performance was, however, not known. We present a complete operando Wide Angle X-Ray Scattering (WAXS) study done at the European Synchrotron Radiation Facility (ESRF) using a dedicated PEM-WE cell. The structure of each sample is observed for several hours under PEM-WE conditions with increasing current density from 100 mA cm-2 to 600 mA cm-2. Consequently, we show the connection of the electrochemical performance of the Ir-Ru 25:75 catalyst to its structural properties and uncover the interplay between the face-centered-cubic iridium and hexagonal-close-packed ruthenium.

Study of Manipulative In Situ Pore-Formation upon Polymeric Coating on Cylindrical Substrate for Sustained Drug Delivery.

Herein, the micro-porous polylactic acid coating applied on the surface of the cylindrical substrate is fabricated by a novel in situ pore-formation strategy based on the combinational effect of breath figure (BF) and vapor-induced phase separation (VIPS) processes. Under the condition of high environmental humidity, solvent pair of chloroform and dimethylformamide is employed for post-treatment onto pre-formed PLA coating to induce the pore-formation following the mechanism of BF and VIPS, respectively. A composite porous structure with both cellular-like and bi-continuous network morphologies is obtained. By tunning the experimental factors including the ratio of the solvent pair, environmental humidity, and temperature, morphological manipulation upon the pore morphology can be facilely achieved based on the control of mechanism transition between BF and VIPS. Paclitaxel is used as a model drug and loaded into the porous coating by the wicking effect of post-immersion. Coatings with different morphological features show varying drug loading and release capacities. The 28-day release test reveals dynamic release profiles between different coating samples, with the total release rate ranging from 35.70% to 79.96%. Optimal loading capacity of 19.28µg cm-2 and 28-day release rate of 35.70% are achieved for the coating with composite BF-VIPS structure. This research established a cost-efficient strategy with high flexibility in the structural manipulation concerning the construction of drug-eluting coating with the feature of manipulative drug delivery.

Determination of 3-acetyl-11-keto-β-boswellic acid in analytical and biological samples using streamlined and robust RP-HPLC method.

AKBA (3-acetyl-11-keto-β-boswellic acid) is a phytoconstituent derived from Boswellia serrata extract and utilized in the management of rheumatoid arthritis. Drug delivery approaches showed interest in delivering AKBA with advanced nanotechnology. There is a need for a simple, sensitive, and robust HPLC method that can determine AKBA in complex nanoformulation and in vitro and ex vivo samples. In the proposed work, the RP-HPLC method was developed using a mobile phase comprising a mixture of acetonitrile : milli Q (90 : 10) at detection λmax 250 nm. The method exhibited a linearity of 250 to 20 000 ng mL-1 with a high correlation coefficient of 1. The limit of detection and limit of quantification for the analytes were found to be 41.32 ng mL-1 and 125.21 ng mL-1, respectively. In the accuracy study, the % recovery of AKBA was found to be 98% to 102%, and the precision study showed less than 2% relative standard deviation. The developed method was found to be robust under chromatographic conditions with changes in pH and mobile phase mixture ratio. The method was also explored for forced degradation study, and the results showed the successful separation of degradation products from the AKBA. Further, the RP-HPLC method was applied for the quantification of AKBA in topical nanoformulations and different matrices, such as skin matrices and adhesive tapes. The method was able to measure entrapment efficiency (93.13 ± 1.94%), drug loading (25.83 ± 0.54%), drug assay in a gel matrix (96.99 ± 3.89%), drug amount in stratum corneum (7.90 ± 0.62 μg cm-2), and drug amount in viable skin layers (33.94 ± 0.21 μg cm-2) with high-speed reproducibility. The developed method can be utilized for the routine analysis of AKBA in conventional and complex formulations in academia and industry.

Metal Doped Unconventional Phase IrNi Nanobranches: Tunable Electrochemical Nitrate Reduction Performance and Pollutants Upcycling.

Electrochemical nitrate reduction (NO3RR) provides a new option to abate nitrate contamination with a low carbon footprint. Restricted by competitive hydrogen evolution, achieving satisfied nitrate reduction performance in neutral media is still a challenge, especially for the regulation of this multielectron multiproton reaction. Herein, facile element doping is adopted to tune the catalytic behavior of IrNi alloy nanobranches with an unconventional hexagonal close-packed (hcp) phase toward NO3RR. In particular, the obtained hcp IrNiCu nanobranches favor the ammonia production and suppress byproduct formation in a neutral electrolyte indicated by in situ differential electrochemical mass spectrometry, with a high Faradaic efficiency (FE) of 85.6% and a large yield rate of 1253 μg cm-2 h-1 at -0.4 and -0.6 V (vs reversible hydrogen electrode (RHE)), respectively. In contrast, the resultant hcp IrNiCo nanobranches promote the formation of nitrite, with a peak FE of 33.1% at -0.1 V (vs RHE). Furthermore, a hybrid electrolysis cell consisting of NO3RR and formaldehyde oxidation is constructed, which are both catalyzed by hcp IrNiCu nanobranches. This electrolyzer exhibits lower overpotential and holds the potential to treat polluted air and wastewater simultaneously, shedding light on green chemical production based on contaminate degradation.

Carbon-Promoted Pt-Single Atoms Anchored on RuO2 Nanorods to Boost Electrochemical Hydrogen Evolution.

While efficient for electrochemical hydrogen evolution reaction (HER), Pt is limited by its cost and rarity. Traditional Pt catalysts and Pt single-atom (aPt) catalysts (Pt-SACs) face challenges in maintaining kinetically favorable HER pathways (Volmer-Tafel) at ultralow Pt loadings. Herein, carbon-promoted aPts were deposited on RuO2 without the addition of reductants. aPts confined on carbon-supported RuO2 nanorods (aPt/RuO2NR/Carbon) promoted "inter-aPts" Tafel. aPt/RuO2NR/Carbon is the Pt-SAC that retained underpotentially deposited H; additionally, its HER onset overpotential was "negative". The aPt/RuO2NR/Carbon exhibited 260-fold higher Pt mass activity (imPt)/turnover frequency (TOF) (522.7 A mg-1/528.4 s-1) than that of commercial Pt/C (1.9 A mg-1/1.9 s-1). In an ultralow Pt loading (0.19 μg cm-2), the HER rate-determining step maintained Volmer-Tafel and the Pt utilization efficiency was 100.3%.

Synthetic silica fibers of different length, diameter and shape: synthesis and interaction with rat (NR8383) and human (THP-1) macrophages in vitro, including chemotaxis and gene expression profile

BackgroundInhalation of biopersistent fibers like asbestos can cause strong chronic inflammatory effects, often resulting in fibrosis or even cancer. The interplay between fiber shape, fiber size and the resulting biological effects is still poorly understood due to the lack of reference materials.ResultsWe investigated how length, diameter, aspect ratio, and shape of synthetic silica fibers influence inflammatory effects at doses up to 250 µg cm-2. Silica nanofibers were prepared with different diameter and shape. Straight (length ca. 6 to 8 µm, thickness ca. 0.25 to 0.35 µm, aspect ratio ca. 17:1 to 32:1) and curly fibers (length ca. 9 µm, thickness ca. 0.13 µm, radius of curvature ca. 0.5 µm, aspect ratio ca. 70:1) were dispersed in water with no apparent change in the fiber shape during up to 28 days. Upon immersion in aqueous saline (DPBS), the fibers released about 5 wt% silica after 7 days irrespectively of their shape. The uptake of the fibers by macrophages (human THP-1 and rat NR8383) was studied by scanning electron microscopy and confocal laser scanning microscopy. Some fibers were completely taken up whereas others were only partially internalized, leading to visual damage of the cell wall. The biological effects were assessed by determining cell toxicity, particle-induced chemotaxis, and the induction of gene expression of inflammatory mediators.ConclusionsStraight fibers were only slightly cytotoxic and caused weak cell migration, regardless of their thickness, while the curly fibers were more toxic and caused significantly stronger chemotaxis. Curly fibers also had the strongest effect on the expression of cytokines and chemokines. This may be due to the different aspect ratio or its twisted shape.

A novel two-stage continuous capacitive deionization system with connected flow electrode and freestanding electrode

The desalination of seawater/wastewater utilizing flow-electrode capacitive deionization (FCDI) has received significant interest. However, challenges like the low electrical conductivity of flow electrode and excessive energy consumption have prevented the scaling up of desalination operations. To overcome these issues, this study introduces a new FCDI system termed the two-stage FCDI (TS-FCDI) system, in which desalination modules are equipped with freestanding and flow electrode. The TS-FCDI system offers a graded desalination module design that produces an average salt removal rate (ASRR) of 113 µg cm2·min−1. However, the TS-FCDI system requires substantially reduced infrastructure investment, device size, and energy expenses. Notably, the design allows for the simultaneous operation of freestanding and flow electrode and enables the transport of ions and charges in the electrode region. Experimental evidence from multiple device configurations (CDI, FCDI, and TS-FCDI) supports this claim. Notably, the TS-FCDI system shows about twice the desalination performance over FCDI, with approximately 50 h of single-cycle (SC) operation. This enhancement links the freestanding electrode with the flow electrode, enabling the device to be well-suited for practical applications. The continuous flow of electrode particles in contact with the freestanding electrode initiates secondary ion transport, merging two different types of electrodes to enhance the active space of the electrode, effectively improving ion adsorption performance. In summary, the results of this study indicate the potential of the TS-FCDI system as a suitable desalination technology for scaling up applications.

Symmetry Evolution Induced 2D Pt Single Atom Catalyst with High Density for Alkaline Hydrogen Oxidation.

The performance of single-atom catalysts is greatly influenced by the chemical environment surrounding the central atom. Here, a salt-assisted method is employed to transform the tetrahedral coordination structure of zeolitic imidazolate frameworks - 8 (ZIF-8)into a planar square coordination structure without altering the ligands. During the subsequent carbonization process, concurrent with the evaporation of zinc atoms, the structure of the nitrogen and carbon carriers (NC carriers) undergoes a transition from five-membered rings to six-membered rings to preserve the 2D structure. This transition results in the generation of additional defect sites on the 2D-NC substrates. Hence, the Pt single-atom catalysts with planar square coordination symmetries can be precisely prepared via electrodeposition (denoted as 2D-Pt SAC). The Pt loading of 2D-Pt SAC is 0.49 ± 0.03 µg cm-2, higher than that of 3D-Pt SAC (0.37 ± 0.04 µg cm-2). In the context of the hydrogen oxidation reaction electrocatalysis, under an overpotential of 50 mV, these single-atom catalysts with 2D coordination exhibit mass activities of 2396 A gPt -1 (32 times higher than commercial Pt/C catalyst, 2 times higher than 3D-PtNC).

Berberine HCl and diacerein loaded dual delivery transferosomes: Formulation and optimization using Box-Behnken design.

Berberine is a poorly water-soluble alkaloid compound showing significant anti-inflammatory characteristics. It reduces the levels of pro-inflammatory and inflammatory cytokines, including tumour necrosis factor (TNF-α, IFN-γ) and interleukin (IL-23, IL-12, and IL-23). Diacerein significantly reduces the splenomegaly associated with psoriasis. It downregulates the production of TNF-α and IL-12. This study reported the development of transferosomes containing berberine HCl and diacerein using a film hydration method followed by optimization using a Box-Behnken design. Sodium deoxycholate was used as an edge activator. The impact of independent variables (amount of phosphatidylcholine, amount of edge activator, and sonication cycles) on dependent variables (particle size and entrapment efficiency) was examined. The optimized formulation was characterized for polydispersity index, vesicle size, entrapment efficiency, ζ potential, spectral analysis like Fourier transform infrared, thermal analysis, X-ray diffraction, deformability, transmission electron microscopy, antioxidant assay, in-vitro release, and ex-vivo skin permeation studies. The optimized formulation had a particle size of 110.90±2.8 nm with high entrapment efficiency (89.50±1.5 of berberine HCl and 91.23±1.8 of diacerein). Deformability, polydispersity index, ζ potential, and antioxidant activity of the optimized formulation were 2.44, 0.296, -13.3, and 38.36 %, respectively. Optimized transferosomes exhibited 82.093±0.81 % and 85.02±3.81 % release of berberine HCl and diacerein after 24 h of dissolution study. The transdermal flux of optimized formulation was 0.0224 μg cm-2 h-1 (2.24 cm h-1 permeation coefficient) and 0.0462 μg cm-2 h-1 (4.62 cm h-1 permeation coefficient), respectively, for berberine HCl and diacerein. Raman analysis of treated pig skin confirmed that the transferosomes can permeate the skin. No change in the skin condition or irritation was observed in BALB/c mice. Formulation stored at 4 and 25±2 °C / 60±5 % relative humidity was stable for 3 months. Thus, the results demonstrated successful optimization of the transferosomes for the efficient topical delivery of berberine HCl and diacerein in the effective management of psoriasis.

The Chemical Landscape of Leaf Surfaces and Its Interaction with the Atmosphere.

Atmospheric chemists have historically treated leaves as inert surfaces that merely emit volatile hydrocarbons. However, a growing body of evidence suggests that leaves are ubiquitous substrates for multiphase reactions-implying the presence of chemicals on their surfaces. This Review provides an overview of the chemistry and reactivity of the leaf surface's "chemical landscape", the dynamic ensemble of compounds covering plant leaves. We classified chemicals as endogenous (originating from the plant and its biome) or exogenous (delivered from the environment), highlighting the biological, geographical, and meteorological factors driving their contributions. Based on available data, we predicted ≫2 μg cm-2 of organics on a typical leaf, leading to a global estimate of ≫3 Tg for multiphase reactions. Our work also highlighted three major knowledge gaps: (i) the overlooked role of ambient water in enabling the leaching of endogenous substances and mediating aqueous chemistry; (ii) the importance of phyllosphere biofilms in shaping leaf surface chemistry and reactivity; (iii) the paucity of studies on the multiphase reactivity of atmospheric oxidants with leaf-adsorbed chemicals. Although biased toward available data, we hope this Review will spark a renewed interest in the leaf surface's chemical landscape and encourage multidisciplinary collaborations to move the field forward.

Enhancing Multi-Spectral Fingerprint Sensing for Trace Explosive Molecules with All-Silicon Metasurfaces.

Spectroscopy is a powerful tool to identify the specific fingerprints of analytes in a label-free way. However, conventional sensing methods face unavoidable barriers in analyzing trace-amount target molecules due to the difficulties of enhancing the broadband molecular absorption. Here, we propose a sensing scheme to achieve strong fingerprint absorption based on the angular-scanning strategy on an all-silicon metasurface. By integrating the mid-infrared and terahertz sensing units into a single metasurface, the sensor can efficiently identify 2,4-DNT with high sensitivity. The results reveal that the fingerprint peak in the enhanced fingerprint spectrum is formed by the linked envelope. It exhibits a significant enhancement factor exceeding 64-fold in the terahertz region and more than 55-fold in the mid-infrared region. Particularly, the corresponding identification limit of 2,4-DNT is 1.32 µg cm-2, respectively. Our study will provide a novel research idea in identifying trace-amount explosives and advance practical applications of absorption spectroscopy enhancement identification in civil and military security industries.

Poly(Allylamine Hydrochloride) and ZnO Nanohybrid Coating for the Development of Hydrophobic, Antibacterial, and Biocompatible Textiles.

In healthcare facilities, infections caused by Staphylococcus aureus (S. aureus) from textile materials are a cause for concern, and nanomaterials are one of the solutions; however, their impact on safety and biocompatibility with the human body must not be neglected. This study aimed to develop a novel multilayer coating with poly(allylamine hydrochloride) (PAH) and immobilized ZnO nanoparticles (ZnO NPs) to make efficient antibacterial and biocompatible cotton, polyester, and nylon textiles. For this purpose, the coated textiles were characterized with profilometry, contact angles, and electrokinetic analyzer measurements. The ZnO NPs on the textiles were analyzed by scanning electron microscopy and inductively coupled plasma mass spectrometry. The antibacterial tests were conducted with S. aureus and biocompatibility with immortalized human keratinocyte cells. The results demonstrated successful PAH/ZnO coating formation on the textiles, demonstrating weak hydrophobic properties. Furthermore, PAH multilayers caused complete ZnO NP immobilization on the coated textiles. All coated textiles showed strong growth inhibition (2-3-log reduction) in planktonic and adhered S. aureus cells. The bacterial viability was reduced by more than 99%. Cotton, due to its better ZnO NP adherence, demonstrated a slightly higher antibacterial performance than polyester and nylon. The coating procedure enables the binding of ZnO NPs in an amount (<30 µg cm-2) that, after complete dissolution, is significantly below the concentration causing cytotoxicity (10 µg mL-1).

Evaluation of viscoelastic parameters and photo-based assessment of newly developed dermal substitutes modified with thermostabilized fibroblast growth factor 2

BackgroundThe purpose of dermal substitutes is to mimic the basic properties of the extracellular matrix of human skin. The application of dermal substitutes to the defect reduces the formation of hypertrophic scars and improves the scar quality. This study aims to develop an original dermal substitute enriched with stable fibroblast growth factor 2 (FGF2-STAB®) and test it in an animal model. MethodsDermal substitutes based on collagen/chitosan scaffolds or collagen/chitosan scaffolds with nanofibrous layer were prepared and enriched with FGF2-STAB® at concentrations of 0, 0.1, 1.0, and 10.0 µg ‧ cm-2. The performance of these dermal substitutes was tested in vivo on artificially formed skin defects in female swine. The outcomes were evaluated using cutometry at 3 and 6 months. In addition, visual appearance was assessed based on photos of the scars at 1-month, 3-month and 6-month follow-ups using Yeong scale and Visual Analog Scale. ResultsThe dermal substitute was fully integrated into all defects and all wounds healed successfully. FGF2-STAB®-enriched matrices yielded better results in cutometry compared to scaffolds without FGF2. Visual evaluation at 1, 3, and 6 months follow-ups detected no significant differences among groups. The FGF2-STAB® effectiveness in improving the elasticity of scar tissues was confirmed in the swine model. This effect was independently observed in the scaffolds with nanofibres as well as in the scaffolds without nanofibres. ConclusionThe formation of scars with the best elasticity was exhibited by addition 1.0 µg ‧ cm-2of FGF2-STAB® into the scaffolds, although it had no significant effect on visual appearance at longer follow-ups. This study creates the basis for further translational studies of the developed product and its progression into the clinical phase of the research.

Diverse genetic basis of Vip3Aa resistance in five independent field-derived strains of Helicoverpa zea in the US.

Practical resistance of Helicoverpa zea to Cry proteins has become widespread in the US, making Vip3Aa the only effective Bacillus thuringiensis (Bt) protein for controlling this pest. Understanding the genetic basis of Vip3Aa resistance in H. zea is essential in sustaining the long-term efficacy of Vip3Aa. The objectives of this study were to characterize the inheritance of Vip3Aa resistance in four distinct field-derived H. zea strains (M1-RR, AC4-RR, R2-RR and R15-RR), and to test for shared genetic basis among these strains and a previously characterized Texas resistant strain (LT#70-RR). Maternal effects and sex linkage were absent, and the effective dominance level (DML) was 0.0 across Vip3Aa39 concentrations ranging from 1.0 to 31.6 μg cm-2, in all H. zea resistant strains. Mendelian monogenic model tests indicated that Vip3Aa resistance in each of the four strains was controlled by a single gene. However, interstrain complementation tests indicated that three distinct genetic loci are involved in Vip3Aa resistance in the five resistant H. zea strains: one shared by M1-RR and LT#70-RR; another shared by R2-RR and R15-RR; and a distinct one for AC4-RR. Results of this study indicate that Vip3Aa resistance in all H. zea strains was controlled by a single, recessive and autosomal gene. However, there were three distinct genetic loci associated with Vip3Aa resistance in the five resistant H. zea strains. The information generated from this study is valuable for exploring mechanisms of Vip3Aa resistance, monitoring the evolution of Vip3Aa resistance, and devising effective strategies for managing Vip3Aa resistance in H. zea. © 2024 The Authors. Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Increased nutritional quality of rice grains and migration mechanisms of selenium by spraying a foliar selenium-rich nutrient solution

Foliar application of selenium (Se) is an effective method for biofortification in rice, to ensure that sufficient Se is supplied by the crop to maintain human health. In order to improve Se concentration in rice and meet the daily recommended intake for humans, a foliar Se fertilizer was applied in five regions of Liaoning and Jilin provinces, China, and its effects on rice quality, leaf morphology, and wax characteristics were assessed in field tests. The effects of alkyl polyglycosides (APG) in the Se fertilizer were evaluated, and epicuticular waxes were measured to analyze the effects of the fertilizer on plant water status. The Se fertilizer effectively enhanced organic Se levels in rice (p < 0.05), ranging from 599.8 to 2002.0 µg kg−1. An intake of 50 g d−1 of Se-enriched rice can meet nutritional requirements, with total Se intake ranging from 30.0 to 100.1 µg d−1. The Se fertilizer increased the protein content and decreased the proportion of chalky rice (p < 0.05). APG increased the wettability of Se fertilizer on the surface of leaves, so Se could be better absorbed into the leaves and accumulate in rice. The Se fertilizer increased the epicuticular wax so that moisture loss from leaves was reduced. Mean cuticular wax thicknesses were 2.36 and 2.25 µg cm2 in Daohuaxiang and Wuyou 4, respectively. These results suggest a link between the quality of rice and epicuticular wax thickness, and the foliar application of Se fertilizer shows promise for increasing Se content in rice grown in Se deficient soils.