Resin Method Research Articles

A novel thermoplastic material: Pre‐polymerized PMMA liquid resin and continuous glass fiber‐reinforced composite initiated by benzoyl peroxide/N,N‐dimethylaniline

AbstractThermoplastic PMMA was rarely exploited in continuous fiber‐reinforced composites due to its viscous high‐temperature molten fluid as well as pessimistic wettability into fiber fabric. Redox‐active polymerization is a green route to develop a new liquid PMMA resin at room temperature to provide an in situ curing with the advantages of energy saving and consumption reduction. In this paper, BPO/DMA was adopted as a redox initiator pair, and the effect of MMA:BPO:DMA ratio on curing time, Mn, Tg, and mechanical properties of PMMA were systematically studied. When the ratio of MMA:BPO:DMA is 200:1.2:1, PMMA‐200 achieved optimistic mechanical properties at 20°C (tensile strength, 64.7 MPa; tensile modulus, 3352 MPa; bending strength, 125.3 MPa; bending modulus, 3023 MPa). Moreover, the mechanical properties were further improved at low temperatures. The maximum tensile strength and tensile modulus were up to 97.43 and 4297 MPa (−40°C) respectively. The tensile strength (0°, 1103 MPa; 90°, 52.3 MPa) and tensile modulus (0°, 47.5 GPa; 90°, 14.2 GPa) of glass‐fiber‐reinforced PMMA composite at 20°C were found to be comparable with epoxy resin‐based composites and even higher at lower temperature. In summary, redox‐initiated PMMA and its fiber‐reinforced composites are promising thermoplastic materials as new lightweight alternatives.Highlights Preparation method of PMMA resin and glass fiber composite. Research on the mechanical properties, molecular weight, glass transition temperature, curing time, etc. of PMMA resin. Testing of mechanical properties of PMMA glass fiber composites at room temperature and low temperature. Current applications and prospects of PMMA glass fiber composites.

Epoxy Value Measurement of E44 Epoxy Resin by Various Chemical Titration Method

AbstractDuring the production of epoxy resins, it is crucial to control or to know the epoxy groups. It is known that epoxy value is the most important analytical index of epoxy resin physical quantity to characterize the number of epoxy groups in epoxy resin. In this paper, two ways for testing the epoxy values of E44 epoxy resin are developed based on chemical titration method: hydrochloric acid‐acetone method and perchloric acid‐tetraethylammonium bromide method. The features of different methods and the influence of approaches on epoxy value are studied systematically. At the significant level of 0.05, for hydrochloric acid‐acetone method, the confidence interval for the mean is (0.454±0.003)eq/100 g, and for perchloric acid‐tetraethylammonium bromide method, the confidence interval for the mean is (0.453±0.003)eq/100 g. It has been proved that the test results of the two methods are basically the same. And the advantages and disadvantages of the two methods have been put forward. In addition, the testing mechanism of hydrochloric acid‐acetone method and perchloric acid‐tetraethylammonium bromide method is illustrated in detail. On the basis of superiority over the two methods, a novel method for testing epoxy resin with rapid and accurate epoxy value can be envisioned.

Retrofitting Techniques: A Comprehensive Review

The need of improving the structural performance of old constructed structures has grown significantly as a result to increasing concerns over deteriorating infrastructure, changing building codes and natural calamities. Retrofitting is one of the best processes to make an existing building safe against future coming earthquakes or other environmental forces. Retrofitting is the process of adding new features to older buildings, bridges and many other structures. It aims to strengthen the structure, to satisfy the load carrying capacity of structure and seismic design. This paper includes study of research papers published in past years related to various methods of retrofitting such as seismic retrofitting, retrofitting by glass fibers, retrofitting by chemicals such as epoxy resin and many other methods. Structures lose their strength in some years, some structures are important in view of public, social or any historical. Retrofitting helps to increase the strength, resistivity and lifespan of structure. Key Words: Retrofitting, Strength, Safety.

Molecular design and application of low dielectric bismaleimide resin

AbstractWith the development of communications technology, the copper‐clad laminate (CCL) for integrated circuits (IC) pointed to the direction of high‐frequency and high‐speed development, that is, a lower dielectric constant and dielectric loss requirements. Bismaleimide (BMI) resins feature stable dielectric properties and excellent thermal stability over a wide temperature range, widely used in the manufacture of high‐frequency and high‐speed CCL substrates. However, the comprehensive performance of BMI resin itself, including dielectric properties, still cannot fully meet the needs of the ever‐changing communications industry, so the molecular design modification of BMI resin to enhance the dielectric properties is currently one of the key research directions for integrated circuit CCL. This paper reviews the development of BMI resins and their applications, focusing on the main methods of molecular design modification and formulation optimization, including allyl, diamine, internal chain‐extended, and chemical/physical blending modification. Finally, the low dielectric BMI resin and its application and development in high‐frequency and high‐speed CCL are summarized and prospected. Future research directions include the design and synthesis of multi‐component copolymers to further realize the balance between low dielectric and comprehensive performance, as well as exploring the possibility of novel composite modifications to provide more competitive high‐performance materials for the IC laminate field.Highlights The development of bismaleimide resin and their applications are reviewed. Bismaleimide monomers' synthesis and chemical reaction are summarized. The modified methods of bismaleimide resin in low dielectric are reviewed. Future research directions of low dielectric bismaleimide are prospected.

Applicability of Multi-coating for Preserving Surfaces of Outdoor Bronze sculptures

The wax used for surface coating of outdoor bronze sculptures is prone to material aging, surface cracking, and whitening due to environmental changes and air pollutants, leading to a shortened coating treatment cycle. To improve these material limitations, I explored the possibility of applying a multi-coating method that uses both acrylic resin and wax in an outdoor environment in Korea. The results of the experiment showed that the multi-coating method significantly improved the durability of the coating layer, weather resistance against external degrading factors, corrosion prevention ability, and contact angle, etc. compared to the existing wax-only coating method, and the rate of color change (ROC) was low, proving its stability. Especially, the double-coating method of acrylic resin and wax using acrylic urethane and Bowling Alley Wax® (acrylic resin + wax) was found to be the most stable coating method among the multi-coating methods. According to such results, I found that the multi-coating method can be proposed as a new surface coating treatment method that can secure long-term preservation of bronze sculptures and preserve their original form even in outdoor environments in Korea, by remedying the shortcomings of the wax-only coating.

Innovative Determination of Zinc Isotope Ratios in Geological Reference Materials: A Combined Precipitation and Anion Exchange Resin Method by MC-ICP-MS

Innovative Determination of Zinc Isotope Ratios in Geological Reference Materials: A Combined Precipitation and Anion Exchange Resin Method by MC-ICP-MS

Are physical and mechanical properties of 3D resins dependent on the manufacturing method?

This research analyzed the effect of the manufacturing method on the flexural strength and color stability of 3D-printed resins used for producing indirect restorations. For this, two dental restorative biocompatible resin materials, OnX (OnX, SprintRay) and CB (Crown and Bridge, Dentca), were divided into 2 groups according with manufacturing method (printed with a Pro95 3D printer - SprintRay; and not printed, with samples obtained with the fluid resin being poured on PVS molds for further light activation in the post-curing process), and subdivided into 2 groups according to the post-curing method: VG (Valo Grand, Ultradent Products) for 120s and PC (Procure 2, SprintRay). Bar-shaped samples were used to evaluate the flexural strength 24h after storage in distilled water at 37°C using a universal testing machine. Disk-shaped samples were used to evaluate the color stability with a spectrophotometer at baseline, after 1-7days in dark dry storage at 37°C, and after 1day of artificial aging in water at 60°C. Data were evaluated using 3-way ANOVA (flexural strength) and 4-way repeated measures ANOVA (color stability), followed by the Tukey's HSD test (α = .05). Flexural strength showed significant results for resin (p < .001), while manufacturing and post-curing methods were not significant (p > .05). The interaction effects between resin and manufacturing method (p = .978), and between resin, manufacturing method and post-curing method (p = .659) were not significant. In general, OnX showed higher flexural strength values than CB, regardless of manufacturing method or post-curing protocol. Color stability results showed significant results for resin (p < .001), time (p < .001), resin and time (p = .029), and resin and curing method (p < .001), but no differences considering resin and manufacturing mode (p = .87), or resin, manufacturing method and curing method (p = .35). In general, OnX showed a higher color change than CB, longer storage times resulted in increased color change for both materials, and CB cured with VG showed lower color alteration than CB cured with PC2. The manufacturing method (3D printed or not 3D printed) does not seem to influence the flexural strength and color stability of 3D printed resins. This may indicate that, at least from a physical-mechanical perspective, the final properties of the material are mainly dependent on the post-curing process.

Synthesis of phenolic resins with cyclotriphosphazene for enhancement of ablation and char yields

A novel phenolic resin with combined hydroxymethyl-substituted phosphazene unit as a part of cured network was prepared which exhibited excellent thermal properties and ablation resistance. The novel phenolic resin was synthesized via copolymerizing from hexa (4-hydroxymethylphenoxy) cyclotriphosphazene (CHPP), phenol and paraformaldehyde. The CHPP contains abundant –CH2OH groups, which can be a part of phenolic resin network through condensation reactions between the –CH2OH groups and active hydrogens on benzene rings of phenolic resins. The optimal curing temperature for the modified phenolic resins was determined using the non-isothermal DSC method. The ablation resistance was investigated using the oxyacetylene flame method. The char yield and linear ablation rate of the modified phenolic resins are 71.3 % and 0.0020 mm/s, respectively. The ablation resistance of the novel resin is significantly improved, compared with other phenolic resin composites. The modification method for the phenolic resin provides a novel pathway to improve the application prospects of phenolic resins in the field of thermal protective materials.

Macroporous polymeric resin for the purification of flavonoids from medicinal plants: A review.

The purification of flavonoids using the macroporous polymer resin method has gained attention in recent years due to its simplicity, precision, cost-effectiveness, and the ability to separate flavonoids from other constituents. Several studies have been conducted to investigate the efficiency and effectiveness of macroporous polymer resin in purifying flavonoids from various plant sources. This review aims to evaluate the existing literature on macroporous polymer resin purification of flavonoids and provide a comprehensive analysis of the current research trends and advancements in this field. It also highlights the importance of optimizing the adsorption parameters and conditions such as resin type, resin concentration, pH, and temperature for efficient purification of flavonoids using macroporous polymer resin. The key findings of this review reveal that macroporous resins with weak polarity, large surface areas, and pore diameters have a stronger adsorption capacity for flavonoids compared to polar resins. Furthermore, ultrasonic-solvent assisted extraction often combines with macroporous resin for effective the extraction and purification of flavonoids.

Improving grapevine virus diagnostics: Comparative analysis of three dsRNA enrichment methods for high-throughput sequencing

The extraction of double stranded (ds) RNA is a common enrichment method for the study, characterization, and detection of RNA viruses. In addition to RNA viruses, viroids, and some DNA viruses, can also be detected from dsRNA enriched extracts which makes it an attractive method for detecting a wide range of viruses when coupled with HTS. Several dsRNA enrichment strategies have been developed. The oldest utilizes the selective binding properties of dsRNA to cellulose. More recent methods are based on the application of anti-dsRNA antibodies and viral proteins with a specific affinity for dsRNA. All three methods have been used together with HTS for plant virus detection and study. To our knowledge, this is the first comparative study of three alternative dsRNA enrichment methods for virus and viroid detection through HTS using virus-infected, and healthy grapevine test plants. Extracts were performed in triplicate using methods based on, the anti-dsRNA antibody mAb rJ2 (Millipore Sigma Canada Ltd, Oakville, ON, Canada), the B2 dsRNA binding protein, and ReliaPrep™ Resin (Promega Corporation, Madison, WI, USA). The results show that the workflows for all three methods are effectively comparable, apart from purification steps related to antibody and binding protein construct. Both the cellulose resin and dsRNA binding protein construct methods provide highly enriched dsRNA extracts suitable for HTS with the B2 method providing a 36× and the ReliaPrep™ Resin a 163× increase in dsRNA enrichment compared to the mAb rJ2 antibody. The overall consistency and cost effectiveness of the ReliaPrep™ cellulose resin-based method and the potentially simpler adaptation to robotics made it the method of choice for future transfer to a semi-automated workflow.

Comparative analysis of AnaLig Sr01 and Sr Resin methods for 210Pb determination in tobacco using TriCarb 3100 TR spectrometry: a statistical approach to accuracy and efficiency

This study aims to statistically compare two methods for determining 210Pb in tobacco: the molecular recognition sorbent method (AnaLig Sr01) and the extraction chromatography sorbent method (Sr Resin). The TriCarb 3100 TR liquid scintillation spectrometer was used to measure and determine 210Pb activity in the tobacco solution. Statistical analysis confirmed the accuracy and precision of the 210Pb measurements, with high detection efficiencies of 82% for both AnaLig Sr01 and Sr Resin. The linear model demonstrated that the residuals followed the Gaussian model, without any autocorrelation or trend. Paired t tests showed consistent results across all methods, and all solid-phase extraction methods proved efficient for 210Pb separations in tobacco samples. These findings provide support for the suitability of both methods and lay a foundation for future articles on tobacco and cigarette samples.

Application of near-infrared-to-blue upconversion luminescence for the polymerization of resin cements through zirconia discs

ObjectivesTo investigate a near-infrared-to-blue luminescence upconversion curing method for polymerizing resin cements under zirconia discs. MethodsLava zirconia discs of different thicknesses (0.5–2.0 mm) were manufactured. First, the transmittances of the NIR and two blue lights (BLs) (LED and halogen lights) through these discs were measured. Second, NaYF4:Yb3+/Tm3+ upconversion phosphor (UP) powder was milled into 0.5-μm particle sizes. A light-curable resin cement VariolinkII base was chosen as the control (UP0), and an experimental cement (UP5) was prepared by adding 5 % UPs. These two cements were examined using multiphoton excitation microscopy for particle distribution. UP5 and UP0 were polymerized with or without zirconia shielding then subjected to a microhardness test. A multifold analysis was performed to examine the effects of zirconia thickness, curing protocols (pure BL or combined BL and NIR curing), and cement type. ResultsThe transmittance of NIR was superior to that of BL through zirconia discs of all thicknesses. UP particles were homogeneously distributed in UP5 and emitted blue luminescence under 980-nm NIR excitation. UP5 showed higher microhardness values than UP0 under any curing protocol or zirconia shielding condition. The combination of 20-s BL and 40-s NIR curing yielded the highest microhardness in uncovered UP5. However, combining 40-s BL and 20-s NIR curing surpassed the other groups when the zirconia discs were thicker than 0.5 mm. SignificanceNIR exhibits higher transmission through zirconia than BL. UP particles work as strengthen fillers and photosensitizers in cements. NIR upconversion curing could be a new strategy for polymerizing resin cements under thick zirconia restorations.

Enrichment of Total Flavonoids and Licochalcone A from Glycyrrhiza inflata Bat. Residue Based on a Combined Membrane-Macroporous Resin Process and a Quality-Control Study.

Glycyrrhiza inflata Bat. produces a lot of licorice waste after water extraction, which also retains abundant total flavonoids (TFs) and licochalcone A. However, licorice residue is often wasted due to the lack of good utilization of resources in practical applications. This study first screened the optimal membrane pore size and resin type and then explored the mechanism and conditions of the adsorption of TFs on the resin. Then, different combinations and sequences of membrane and macroporous resin (MR) methods were investigated. It was found that using the membrane method for initial purification, followed by the MR method for further purification, yielded the best purification results. Next, response surface methodology was utilized to investigate the resin's dynamic desorption conditions for TFs. Finally, the TF purity increased from 32.9% to 78.2% (2.38-fold) after purification by a combined membrane-MR process; the purity of licochalcone A increased from 11.63 mg·g-1 to 22.70 mg·g-1 (1.95-fold). This study verified the feasibility of enriching TFs and licochalcone A from licorice residue using a membrane-MR coupling method. In addition, a quality-control method was established using a fingerprinting method on the basis of ultrahigh-performance liquid chromatography (UPLC) to ensure the stability of the enrichment process.

Comparative Analysis of Soil Phosphorus Determination Methods and Their Correlation with Plant Phosphorus in Standing Wheat Crops

This study compared the accuracy of various soil phosphorus assessment methods to measure the soil's ability to supply plants with phosphorus over a brief period in the field. Twenty individual soil samples were collected from a standing wheat (Triticum aestivum L) crop at depths ranging from zero to twenty centimeters. An equivalent plant spike sample was also procured from the soil sampling fields. In comparison to the wet acid digestion method used to detect phosphorus in plants, several methods were utilized to assess phosphorus in the soil, including resin extractable phosphorus, AB-DTPA extractable phosphorus, NaHCO3 extractable phosphorus, water-soluble phosphorus in suspension, and paste. The levels of variation and deficiency of phosphorus, which were found by different methods followed different patterns as shown by the fact that, AB-DTPA method finds phosphorus deficiency in 20% of samples while on the other hand, Olsen method finds phosphorus deficiency in 80% of samples. Even with such a small sampling area, none of the procedures showed a significant correlation with any other method that might account for uneven variation among the samples when determined by distinct procedures. However, corrections were observed to a certain degree between ammonium bicarbonate-diethylenetriaminepentaacetic acid (AB-DTPA) extractable and resin, as well as between other procedures and the plant P scale. Both resin and ammonium bicarbonate-diethylenetriaminepentaacetic acid (AB-DTPA) had a strong relationship with plant phosphorus, with the former showing a significant correlation of 0.48 and 0.21, respectively. Hence Resin and AB-DTPA methods are recommended for the determination of phosphorus under certain soil and plant conditions.

Adsorption of Scandium Ions by Amberlite XAD7HP Polymeric Adsorbent Loaded with Tri-n-Octylphosphine Oxide.

In an actual economic context, the demand for scandium has grown due to its applications in top technologies. However, further development of new technologies will lead to an increase in the market for Sc related to such technologies. The present study aims to improve and upgrade existing technology in terms of efficient scandium recovery, proposing a new material with selective adsorptive properties for scandium recovery. To highlight the impregnation of Amberlite XAD7HP resin with tri-n-octylphosphine oxide extractant by the solvent-impregnated resin method, the obtained adsorbent material was characterized by physico-chemical techniques. Further, the specific surface of the adsorbent and the zero-point charge of the adsorbent surface have been determined. Different parameters, such as initial concentration, adsorbent amount, contact time, or temperature, have been studied. The initial pH effect was investigated when a maximum adsorption capacity of 31.84 mg g-1 was obtained at pH > 3, using 0.1 g of adsorbent and a contact time of 90 min and 298 K. An attempt was made to discuss and provide a clear representation of the studied adsorption process, proposing a specific mechanism for Sc(III) recovery from aqueous solutions through kinetic, thermodynamic, and equilibrium studies. Adsorption/desorption studies reveal that the prepared adsorbent material can be reused five times.

Finemet nanocrystalline magnetic powder cores: Application of binder and warm compaction process

In this paper, Finemet flake amorphous powder with poor flowability is used as raw material to investigate the effect of the type of silicone resin and compaction method on the density and soft magnetic properties of the magnetic powder cores. The results show that due to the different thermal stability of the three silicone resins 600, S2 and JH, the permeability of the three magnetic powder cores has significant differences. Since the lubricant is in a viscous flow state during the warm compaction and reduces the friction between the particles, the density of the magnetic powder cores is increased, which further improves the soft magnetic properties of the magnetic powder cores. Among them, the density of Finemet magnetic powder cores prepared by warm compaction with the S2 silicone resin as binder is 5.62 g∙cm−3, the permeability is 43.86, the DC bias capability is 66.77 % at 100 Oe, and the total loss is 113.94 mW∙cm−3 (100 kHz, 50 mT), which has excellent comprehensive soft magnetic properties and is a very significant improvement compared with cold compaction. This shows that the warm compaction process is an effective method to further improve the soft magnetic properties of magnetic powder cores.

Effects of aging on attachment of Candida albicans to conventional heat-polymerized, CAD-CAM milled, and CAD-CAM 3D-printed acrylic resin bases.

The aim of this study was to assess Candida albicans attachment on conventionally fabricated (polymethylmethacrylate, PMMA), CAD-CAM milled, and 3D-printed acrylic resin bases pre- and post-simulated thermal aging, along with examining material surface changes after aging. Forty-six samples (10mm×10mm×2mm) for each of four material groups (conventional heat-polymerized PMMA, CAD-CAM milled acrylic resin base, CAD-CAM 3D-printed methacrylate resin base, CAD-CAM 3D-printed urethane methacrylate resin base) were subjected to 0, 1, or 2 years of simulated thermal aging. Microscopic images were taken before and after aging, and C. albicans attachment was quantified using cell proliferation assay (XTT). Statistical analysis employed analysis of variance (α = 0.05). Two-way factorial analysis showed no significant differences based on acrylic resin type or thermal aging (p=0.344 and p=0.091 respectively). However, C. albicans attachment significantly differed between 0- and 2-year thermally aged groups (p=0.004), mainly due to elevated initial attachments on CAD-CAM milled acrylic resin base and CAD-CAM 3D-printed urethane methacrylate resin base. Regardless of the fabrication technique and material combination, no significant differences were found in C. albicans adhesion pre- or post- thermal aging. Milled and 3D-printed bases compared favorably with heat- polymerized PMMA in their affinity for C. albicans attachment and surface characteristics after aging. These findings indicate that the risk of patients developing denture stomatitis might not be linked to the type of acrylic resin or fabrication method used.

Evaluation of Functionalized Amberlite Type XAD7 Polymeric Resin with L-Valine Amino Acid Performance for Gallium Recovery.

Given the ever-increasing demand for gallium(III) as a crucial precursor in the fabrication of advanced materials, there arises an imperative to devise efficient recovery processes from primary and secondary sources. In the present investigation, the retrieval of gallium(III) from aqueous solutions through the mechanism of adsorption was investigated. Materials with superior adsorbent properties play an important role in the dynamics of the adsorption process. To enhance these properties, select materials, such as Amberlite-type polymeric resins, are amenable to functionalization through impregnation with extractants featuring specialized active groups, designed for the selective recovery of metal ions-specifically, Ga(III). The impregnation method employed in this study is the Solvent-Impregnated Resin (SIR) method, utilizing the amino acid DL-valine as the extractant. The new material was characterized through Scanning Electron Microscopy (SEM), Elemental Analysis via X-ray energy-dispersive spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR) to elucidate the presence of the extractant on the resin's surface. Concurrently, the material's pHPZC was determined. The adsorptive prowess of the synthesized material was investigated through kinetic, thermodynamic, and equilibrium studies. The influence of specific parameters in the adsorption process-namely, pH, contact time, temperature, and Ga(III) initial concentration-on the maximal adsorption capacity was determined. The optimal adsorption conditions were established using the Taguchi method.

Coprecipitation as a One-Step Se Separation for Determination of Isotope Ratios Completed with Revised Uncertainty Evaluation.

This study introduces a simplified purification method for analyzing 82Se/78Se isotope ratios in diverse natural samples using hydride generation MC-ICP-MS. Unlike the thiol resin method, which is time-consuming and sensitive to the concentrations of reagents used at individual stages, our proposed alternative is quicker, simpler, and robust. The procedure involves coprecipitation of selenium with iron hydroxide and dissolution in hydrochloric acid. Combining hydride generation and a second cleanup stage achieves sufficient purification for Se isotope ratio measurements. The method is efficient, taking 3-4 h after sample decomposition, utilizing common reagents [HCl, Fe(NO3)3, NH4Cl] without evaporation or clean lab conditions. Results on 82Se/78Se isotope ratios in various matrices are presented, comparing them with literature data. All isotopic results have been subjected to a newly proposed state-of-the-art approach to uncertainty estimation dedicated to isotope ratio measurements. The approach is based on applying Monte Carlo simulations with consideration of different samples' results normalized by the expected value. By doing that, we obtained estimated uncertainty for any Se sample with the influence of particular measurements on the final estimation included. We employ a Monte Carlo simulation-based uncertainty estimation approach for isotope ratio measurements, providing estimated uncertainty for each selenium sample.

Structure characterization of aged automobile exhaust catalysts using electron probe microanalysis

BackgroundDriven by emission regulations, the technology of emission control catalysts has been under increasing need for development. Understanding the deactivation mechanism of aged or spent automobile exhaust catalysts is the key to extending their service lifetime. However, the lack of comprehensive microstructural characterization results in an incomplete understanding of their physicochemical properties. Deactivation mechanism of automobile exhaust catalysts is a considerably complex phenomenon, it can be classified into three groups based on its origin: thermal sintering, chemical poisoning and mechanical deactivation. ResultsIn this study, an aged high-mileage automobile exhaust catalyst with Pd and Rh active phases supported on a cerium zirconium oxide doped alumina coating on cordierite was analysed; six consecutive monolithic blocks along the inlet to the outlet of the aged catalyst were extracted, and the corresponding metallographic samples were fabricated using the vacuum impregnation resin method. The purpose of this study was to accurately characterize the different regions of the monolith via electron probe microanalysis and to infer potential causes of catalyst deactivation. Two major causes of deactivation were found: (1) aggregation and alloying of precious-metal particles caused by thermal sintering and (2) chemical poisoning caused by sulphur and phosphorus. Other mechanisms, such as mechanical degradation, which mainly manifests as the loss or wear of the washed coating, were also found to be involved in deactivation. Additionally, the catalytic activity tests showed a considerable decrease in the aged catalyst. The poison concentration trends in the washcoat indicated that P is detrimental to CO oxidation, while S accumulation affects propane oxidation. SignificanceThis analysis method can be of substantial practical significance in developing advanced washcoat materials. Meanwhile, it has great potential in the washcoat analysis of honeycomb-shaped monolithic catalyst, such as natural gas catalyst, diesel vehicle oxidation catalyst and other honeycomb catalysts applied in chemical industry.