Medium Voltage Smart Grids Research Articles

Power Monitoring and Control System for Medium Voltage Smart Grid Using IoT

This paper presents a power monitoring and control system for a medium voltage smart grid system. The smart grid interconnects the power sources between solar PV panel and 220V distribution network. This system consisting major components of inverters, measuring meters, solar charge controllers, relays, Arduino NANO and Raspberry Pi. The Current, power and energy readings are duly recorded. The Internet of Things (IoT) plays the vital role in the data communication between the sensors and electric power system. The voltage and current sensor data is used for the protection of power system network. In the traditional systems only the communication is uni-directional. The reliability of power supply is increased by used the bi directional network communication medium such as IoT. The tabulated results of voltage levels between 203.5V up to 212.8V shows the feasibility and effectiveness of proposed design. The proposed IoT model demonstrated the bidirectional communication from the sensors to the control unit and vice versa.

A New Coupling Solution for G3-PLC Employment in MV Smart Grids

This paper proposes a new coupling solution for transmitting narrowband multicarrier power line communication (PLC) signals over medium voltage (MV) power lines. The proposed system is based on an innovative PLC coupling principle, patented by the authors, which exploits the capacitive divider embedded in voltage detecting systems (VDS) already installed inside the MV switchboard. Thus, no dedicated couplers have to be installed and no switchboard modifications or energy interruptions are needed. This allows a significant cost reduction of MV PLC implementation. A first prototype of the proposed coupling system was presented in previous papers: it had a 15 kHz bandwidth useful to couple single carrier PSK modulated PLC signals with a center frequency from 50–200 kHz. In this paper, a new prototype is developed with a larger bandwidth, up to 164 kHz, thus allowing to couple multicarrier G3-PLC signals using orthogonal frequency division multiplexing (OFDM) digital modulation. This modulation ensures a more robust communication even in harsh power line channels. In the paper, the new coupling system design is described in detail. A new procedure is presented for tuning the coupling system parameters at first installation in a generic MV switchboard. Finally, laboratory and in-field experimental test results are reported and discussed. The coupling performances are evaluated measuring the throughput and success rate in the case of both 18 and 36 subcarriers, in one of the different tone masks standardized for the FCC-above CENELEC band (that is, from 154.6875–487.5 kHz). The experimental results show an efficient behavior of the proposed coupler allowing a two-way communication of G3-PLC OFDM signals on MV networks.

A New Low Cost Coupling System for Power Line Communication on Medium Voltage Smart Grids

This paper proposes and verifies the performance of an innovative and low cost coupling system for power line communication (PLC) on medium voltage (MV) smart grids. The coupling system makes use of the capacitive divider of the voltage detecting systems (VDSs) to inject and receive the PLC signal. VDS are usually already installed in the MV switchboards of the major electrical manufacturer all over the world according to IEC 61243–5. VDS are used to detect the presence of the mains voltage to guarantee personnel safety. An interface circuit has been developed to be connected between the PLC transceiver and the VDS socket. In this way, the PLC signal can be coupled to the MV network without installing a dedicated MV coupler, thus avoiding the related costs of the coupler, the installation, and the temporary service interruption. The innovative device is able to couple digitally modulated narrowband PLC signals with modulation rate up to 19.2 kbit/s. In this paper, first a description of the proposed solution is reported. Second, its communication performance has been tested in laboratory. Finally, different tests have been carried out in two MV smart grid real installations under normal operation, i.e., in the presence of the mains voltage.

An Innovative Measurement Approach for Load Flow Analysis in MV Smart Grids

This paper proposes a novel measurement procedure for load flow analysis in medium voltage (MV) smart grids. The new approach is based on power measurements at low voltage (LV) side of MV/LV distribution substations. Such measurements are carried out by means of power quality analyzers. If compared with the load flow methods based on measurements at the MV side, the proposed approach has a lower cost and it offers an equally reliable measurement system. The proposed algorithm takes the basic concept of the current summation backward/forward method; some modifications are introduced to use LV load powers measurements. To this aim, the MV/LV power transformer is properly modeled and taken into account in the algorithm. The proposed approach is validated by means of both simulations and experimental measurements; the test system is the MV distribution grid of Ustica Island, Italy. First, the proposed algorithm is compared with the MATLAB/Simulink load flow tool, which is based on the traditional Newton-Raphson method. Second, a comparison is carried out between the proposed method and the measurement data collected in the actual MV network of Ustica. Such comparison takes into account the uncertainties of both proposed method, and experimental active and reactive MV power measurements.