Mechanical Properties Of Fibers Research Articles

Effects of MgO on the fibre spinnability, mechanical properties and acid resistance of simulated Martian soil

The ultimate goal of Mars exploration is to construct a Mars base. In particular, it is necessary to prepare fibres by using Martian soil as a raw material. High-strength "Martian glass fibres" can be used to reinforce composite materials to meet the requirements of high-strength functional materials in base construction. Owing to the wide variation in MgO content in Martian soil, in this study, the effects of MgO on the structure, strength and acid resistance of "Martian glass and glass fibres" were investigated. The preparation conditions and mechanical properties of simulated Martian soil fibre (SMSF) were studied via DSC, XRD, Raman, NMR, FT-IR and high-temperature rotational viscometry. The corrosion behaviour of MgO-SMSF in H2SO4 solution was subsequently studied via SEM/EDS. The results showed that MgO reduces the spinnability window and prevents the fibres from stretching continuously, and a threshold appears to exist at 10.89 % MgO. The viscosity of the melt decreased significantly, and the crystallization trend increased with MgO above the threshold. The fibre tensile strength showed a nonlinear relationship with a 22.85 % increase in the fibre tensile strength at 9.24 % MgO. SEM/EDS revealed that the surface of the SMSF formed a gel layer, and the mass retention of the MgO-SMSF in the H2SO4 solution reached 90.17 %. The corrosion of SMSF under acidic conditions was controlled by ion diffusion, with Mg+ and Ca+ diffusing to the fibre surface, resulting in nonuniform corrosion. Raman-based statistical structureproperty modelling further explains the impact of MgO-induced structural changes on the tensile strength and elastic modulus, with good agreement between the model predictions and measured values.

Ultimate resistance and fatigue performance predictions of woven-based fiber reinforced polymers using a computational homogenization method

PurposeIn order to achieve the desired macroscopic mechanical properties of woven fiber reinforced polymer (FRP) materials, it is necessary to conduct a detailed analysis of their microscopic load-bearing capacity.Design/methodology/approachUtilizing the representative volume element (RVE) model, this study delves into how the material composition influences mechanical parameters and failure processes.FindingsTo study the ultimate strength of the materials, this study considers the damage situation in various parts and analyzes the stress-strain curves under uniaxial and multiaxial loading conditions. Furthermore, the study investigates the degradation of macroscopic mechanical properties of fiber and resin layers due to fatigue induced performance degradation. Additionally, the research explores the impact of fatigue damage on key material properties such as the elastic modulus, shear modulus and Poisson's ratio.Originality/valueBy studying the load-bearing mechanisms at different scales, a direct correlation is established between the macroscopic mechanical behavior of the material and the microstructure of woven FRP materials. This comprehensive analysis ultimately elucidates the material's mechanical response under conditions of fatigue damage.

Effect of CNT Oxidation on the Processing and Properties of Superacid-Spun CNT Fibers.

Spinning fibers from carbon nanotube (CNT)/superacid dispersions has emerged as a promising strategy for industrial-scale production of high-performance CNT fibers (CNTFs). The oxygen content and types of functional groups on CNT surfaces significantly influence dispersion, assembly processes, and fiber properties. In this study, Tuball-SWCNTs were purified and oxidized at varying levels. The dispersion behavior of CNTs with different oxidation levels in chlorosulfonic acid was systematically observed, and the mechanical properties of fibers spun from these dispersions were compared. By adjusting the dispersion concentration, highly oriented CNTFs were produced with a specific strength of 1.03 N/tex, a tensile strength of 1.59 GPa, and an electrical conductivity of 3.58 MS/m. Further investigations indicated that oxygen-containing functional groups decrease the coagulation rate, increasing the maximum draw ratio during spinning and improving CNT alignment in the fibers. Molecular dynamics simulations demonstrated that these functional groups (-OH, -COOH) enhance load transfer between CNTs through hydrogen bonding. This specific strength is the highest achieved using Tuball-SWCNTs for superacid-spun fibers, surpassing previous works due to the oxidation-controlled coagulation rate, enhanced fiber orientation, and improved load transfer via hydrogen bonding. This study provides insights for designing and optimizing high-performance CNTFs.

Preparation and characterization of high load‐bearing needled composite preform based on novel ordered short fiber network needling method

AbstractNeedled preform and its composite using felt and base cloth stacked needled have small fiber volume fraction and relatively weak mechanical properties, which are difficult to meet the service requirements of structural and functional integrated components of high‐speed aircraft. Responding to this issue, this paper proposed a new method for preparing high load‐bearing needled composite preform based on ordered short fiber network needling. The high load‐bearing needled preforms were prepared by designing different structural parameters of ordered short fiber network and forming process parameters, and then preform structure was characterized and mechanical properties were tested. The results showed that using ordered short fiber network as carrier of the short fibers, the formed needled fiber bundles were longer and denser, volume content of needled fiber bundles and mechanical properties of needled preform were greatly improved, and needled fiber bundles volume content of ordered short fiber network reinforced needled preform was 1.5 times and 46.3 times that of half‐cut cloth and felt respectively. Compared with traditional felt needled preform and half‐cut cloth needled preform, the interlaminar peeling strength of the ordered short fiber network reinforced needled preform increased by up to 246.4% and 49.2%, respectively. The tensile strength of ordered short fiber network reinforced needled preform was 12.9% higher than that of half‐cut cloth in X‐axis direction. In addition, the effects of ordered short fiber network structure, short fiber length, areal density and needling density on the needled preform structure and properties were also revealed.Highlights High load‐bearing needled composite preform was prepared based on novel ordered short fiber network needling method. The needled fiber bundles formed by using ordered short fiber network were longer and denser, and their volume content was 46.3 times that of felt needled preform. The interlaminar peeling strength of the ordered short fiber network reinforced needled preform increased by up to 246.4%. The tensile strength of ordered short fiber network reinforced needled preform was 12.9% greater than half‐cut cloth in the X‐axis direction.

Plastic deformation of the microfibrils in wet polyacrylonitrile fibers induced by the stretching field

AbstractThe plastic deformation of the microfibrils governs the formation and development of orientation, crystallization, and structural defects in polyacrylonitrile (PAN) fibers due to the flow‐fiber coupling effect during stretching process. In this study, we investigated the morphological changes of microfibrils in PAN fibers during wet‐fiber stretching using ultrathin section technology and electron microscopy observation. Their plastic deformation mechanism was also revealed. An interconnected network was formed and separated by the pore/voids during coagulation process. Stretching forces facilitated the plastic deformation of microfibrils, resulted in their elongation and orientation. Moreover, the inter‐fibril distance reduced and pore/void shape and dimensions were changed. The distinct response of microfibril elements under stretching force resulted in skin‐core structures within the fiber. Tensile strength increased from 27 to 382 MPa, while elongation at break decreased from 225% to 28%. Aligned microfibrils exhibited high tensile strength, whereas unoriented microfibrillar networks showed relatively high elongation properties. Additionally, we proposed a relationship between microfibril morphology changes and fiber mechanical properties.

Degree of Cure, Microstructures, and Properties of Carbon/Epoxy Composites Processed via Frontal Polymerization.

The frontal polymerization (FP) of carbon/epoxy (C/Ep) composites is investigated, considering FP as a viable route for the additive manufacturing (AM) of thermoset composites. Neat epoxy (Ep) resin-, short carbon fiber (SCF)-, and continuous carbon fiber (CCF)-reinforced composites are considered in this study. The evolution of the exothermic reaction temperature, polymerization frontal velocity, degree of cure, microstructures, effects of fiber concentration, fracture surface, and thermal and mechanical properties are investigated. The results show that exothermic reaction temperatures range between 110 °C and 153 °C, while the initial excitation temperatures range from 150 °C to 270 °C. It is observed that a higher fiber content increases cure time and decreases average frontal velocity, particularly in low SCF concentrations. This occurs because resin content, which predominantly drives the exothermic reaction, decreases with increased fiber content. The FP velocities of neat Ep resin- and SCF-reinforced composites are seen to be 0.58 and 0.50 mm/s, respectively. The maximum FP velocity (0.64 mm/s) is observed in CCF/Ep composites. The degree of cure (αc) is observed to be in the range of 70% to 85% in FP-processed composites. Such a range of αc is significantly low in comparison to traditional composites processed through a long cure cycle. The glass transition temperature (Tg) of neat epoxy resin is seen to be approximately 154 °C, and it reduces slightly to a lower value (149 °C) for SCF-reinforced composites. The microstructures show significantly high void contents (12%) and large internal cracks. These internal cracks are initiated due to high thermal residual stress developed during curing for non-uniform temperature distribution. The tensile properties of FP-cured samples are seen to be inferior in comparison to autoclave-processed neat epoxy. This occurs mostly due to the presence of large void contents, internal cracks, and a poor degree of cure. Finally, a highly efficient and controlled FP method is desirable to achieve a defect-free microstructure with improved mechanical and thermal properties.

Investigating long term storage stability and drug release behavior of polypeptide based fibrous scaffold for tissue engineering application

Electrospun poly (γ-benzyl-l-glutamate) (PBG) scaffold felt with aligned fibers shows promising nerve regeneration and neurite growth capability due to the nerve stimulating moiety of glutamate in the PBG material. The nerve regeneration capability can be further enhanced by incorporating 4 wt% minocycline hydrochloride (MH) in the scaffold (PBGMH4). They are useful in the nerve tissue engineering to repair and regeneration damaged nerves in central nerve system or peripheral nerve system. Here we investigate the ambient storage capability of PBG and PBGMH4 by monitoring the changes over time of fiber dimension, mechanical properties of both scaffolds and amount of drug release of PBGMH4. It is interesting to observe the diameter of fibers and mechanical strength of scaffolds increases but the amount of drug release decrease with time. By carefully examining the top view of the scaffolds using scanning electron microscopy (SEM), the fiber diameter of PBG increased by 58 % over the 12 months storage period, which is larger than the 32 % increase observed for PBGMH4. Furthermore, after storage for 12 months, the difference in fiber diameter between the top and bottom sides of PBG scaffold is 25.9 %, whereas for PBGMH4 is only 6.3 %. These results demonstrate that the PBGMH4 scaffold exhibits superior storage stability compared to that of PBG. Because the fibers of the scaffolds are aligned without any crosslinkage, the scaffolds are porous structure of felts. The porosity of PBGMH4 scaffold is decreased from 90 % to 72 % which can be accountable for the decrease of drug release from initial 42 % to a stabilized 26 % after 9 months of storage. The results indicate the specific surface area of the scaffolds play an important role in governing drug release kinetics. This study thoroughly investigates the storage stability of PBG and PBGMH4 electrospun fibrous scaffolds. The observed correlations between fiber diameter, mechanical properties, and drug release behavior hold implications for the design of advanced bioscaffolds. The long shelf life of optimal PBGMH4 scaffold shows potential application for the nerve regeneration and controlled drug delivery systems.

Influence of Different Retting on Hemp Stem and Fiber Characteristics Under the East of France Climate Conditions

ABSTRACT Historically, for fiber extraction, the stems were immersed in water. However, this method proved far too polluting, leading to its substitution by the dew-retting method in the field. Different retting processes and durations can produce significant differences in hemp stems and fiber characteristics. Both dew- and water-retting methods were carried out on the Santhica 27 cultivar in Eastern France in 2020. An analysis of the stem chemical composition and characteristics has been performed to observe the stem degradation during retting for both methods. Secondly, the analyses of the fiber chemical composition, color, morphological and mechanical properties have been performed to evaluate the impact of retting on the fiber quality. The effect of the retting on the stem and the fiber is observed after 1 week for water-retting and after 4 weeks for dew-retting. For dew-retting, the percentages of fine fiber and cellulose in the fiber bundle increase after 1 week, while the stem chemical composition decreases. Unlike in the dew-retting, the percentage of fine fiber and cellulose in the fiber bundle increases after 4 weeks, while the potassium percentage in the stem, fiber brightness, and fiber tenacity and strain decrease. Finally, after 8 weeks, the fiber properties were found to be similar for both methods.

Influence of carbonisation temperatures on multifunctional properties of carbon fibres for structural battery applications

Carbon fibres are multifunctional materials considered for the realisation of structural battery electrodes. Processing conditions affect the carbonaceous microstructure of carbon fibres. The microstructure dictates the fibre's mechanical properties, i.e. modulus and strength, as well as its electrochemical capacity. Here, carbon fibre processing conditions are investigated to identify the effect of carbonisation temperature on carbon fibre multifunctionality. Different thermal conditions during carbonisation are considered, while keeping the precursor material, applied tension, and oxidation temperature constant. The carbonaceous microstructure of fibres is investigated via wide‐angle x‐ray scattering (WAXS) and transmission electron microscopy (TEM) analyses to determine the effect of the carbonisation temperature. Mechanical and electrochemical tests are performed to characterise carbon fibre multifunctionality with respect to mechanical and electrochemical performance. A moderate trade‐off between mechanical and electrochemical performance is demonstrated, where the elastic modulus and strength decrease and the electrochemical capacity increase with reduced carbonisation temperature. Here, for the studied temperature interval, the elastic modulus and strength is found to drop up to 7% with a 15% increase in capacity. Thus, fibres customised for targeted multifunctionality within a limited design space can be realised by careful selection of the processing conditions in conventional carbon fibre manufacture.

Experimental Analysis of Mechanical Properties of Fiber Reinforced Cenosphere Lightweight Concrete with Higher Temperature Effect

The aim of this research is to explore the impact of polypropylene fibers and glass fibers on the mechanical characteristics of lightweight concrete when subjected to elevated temperatures. Different fiber ratios ranging from 0.25% & 0.50% by volume of concrete were tested to evaluate their impact on various concrete mixtures. Cenosphere is lightweight material as used with cement as bonding material. Pumice aggregate, which is known for its lightweight properties, was utilized as the coarse aggregate. The study aimed to explore various characteristics of lightweight concrete such as slump value, unit weight, and compressive, tensile, and flexural strength. The concrete samples were subjected to different temperatures ranging from 200°C to 400°C for two hours. The findings revealed that the addition of glass fibers improved the tensile strength of the concrete and enhanced the compressive and flexural strength of the lightweight concrete. However, the incorporation of polypropylene fibers resulted in more cracks and pore formation in the concrete. Additionally, the compressive and flexural strength of the concrete decreased with an increase in temperature up to 400°C.

Improving the mechanical performance of railway concrete sleepers using recycled materials: An experimental and numerical study

This paper explores the use of three waste materials available in vast quantities, including waste tires, glass bottles and bamboo furniture, in the manufacture of railway sleepers. Mechanical properties of recycled concrete have been studied to establish an optimal mix suitable for concrete railway sleeper manufacturing. Thus, 5%, 10%, 15% and 20% recycled rubber sands (RRS) by volume of fine aggregate are used instead of 30# and 60# mesh sizes of fine aggregate. Moreover, 20%, 40%, 60%, 80% and 100% of aggregate volume are replaced by recycled glass aggregate (RGA) particles. Furthermore, different percentages of recycled bamboo fibers (RBF) have been used as 1%, 2% and 3% by volume of concrete. According to the optimal concrete mixtures of RRS, RGA and RBF, twelve concrete railway sleepers are manufactured and tested for middle and rail seat bending strengths. Results show that ref. sleeper has almost 16% and 24% lower strengths than RGA sleeper in middle and rail seat, respectively, while ref. sleeper have higher strengths by 16% and 13%, and 18% and 7% than RRS sleeper (M60-R5) and RBF sleeper (B2) in middle and rail seat, respectively. The FEM results show that the ([Formula: see text]) of the RGA sleeper is the minimum ratio by 1.11 and 1.13 for rail seat and middle of sleeper, respectively, which is the best performance. In RBF sleeper FEM model, Bamboo fiber can only bear 5% and 8% of total stress in middle and rail seat, respectively, due to low mechanical properties of fibers.

Pulp and Paper Characteristics of Five Lesser-known Species in Kalimantan: Effects of Re-beating

Five lesser-known species from natural forests in Central Kalimantan, viz., cempaka (Michelia champaca Linn), mentawa (Artocarpus rigidus Blume), menjalin (Xanthophyllum excelsum Miq.), kempili (Lithocarpus elegans (Blume) Hatus. Ex Soepadmo), and sempori (Dillenia sp.) were evaluated in the laboratory for their specific gravity, fiber morphology, pulping and papermaking properties. In addition, their properties after three-phase beating were also evaluated from a recycled paper point of view. The specific gravity and fiber length range were 0.58~0.68 and 1239~2479 μm, respectively. The highest value in specific gravity was observed in menjalin wood, while the longest fiber was observed in sempori. Kraft pulping with 14% active alkali (as Na2O), 23% sulfidity, 2 h at the maximum temperature showed that the highest screened yield was determined in cempaka wood (44.29%) with a kappa number of 17.6. The freeness ranges of unbeaten pulp were 675~780m mL CSF. The freeness ranges of 1st, 2nd, and 3rd beating were 539~630 mL, 235~275 mL, and 220~230 mL CSF, respectively. The 1st beating exhibited the best mechanical properties. Among the species, cempaka, kempili, and mentawa showed comparatively high tensile (57~60 Nm/g) and burst index (2.6~3.4 KPa m2/g), whereas the highest value for tear index (5.02 mNm2/g) was observed in sempori. A considerable decrease in fiber length, slenderness ratio, and mechanical properties of the paper was observed with an increased beating number. These findings suggest that cutting the fibers or decreasing the slenderness ratio was the main factor causing the strength to decrease.

Machine learning assisted mechanical properties prediction of fine denier polyester fiber

In recent years, more and more attention has been attracted by fine denier polyester fibers in electronic information industry due to their unique structural and excellent mechanical properties. As known, the mechanical properties of fine denier polyester fibers have a close relationship with their melt-spinning process parameters, thus, it is worth further exploring the influence of process parameters on fiber mechanical properties (namely breaking strength, elongation at break and CV of breaking strength). This study aims to develop a novel prediction model based on the artificial neural network (ANN) to predict the key mechanical properties of fine denier polyester fibers. For this purpose, firstly, different specifications of fine denier polyester fibers with different mechanical properties are produced by adjusting the key melt-spinning parameters, namely spinning temperature, take-roll speed and metering pump speed. Then the experimental data is collected, analyzed and augmented with effect to be used for modeling. Next, a novel prediction model based on ANN is developed by importing the two-streams structure and two attention matrices to improve the feature abstraction for mechanical properties prediction. Lastly, different predictive performance indicators, namely root mean square error (RMSE), mean absolute percent error (MAPE) and the coefficient of determination (R2) are imported to evaluate the proposed model. For the total of three mechanical properties, the predicted results of the proposed model in terms of RMSE, MAPE and R2 are respectively 0.3499, 0.0906 and 2.9516.

Remnant polarization and structural arrangement in P(VDF-TrFE) electrospun fiber meshes affect osteogenic differentiation of human mesenchymal stromal cells

Many tissues and cells are influenced by mechano-electric stimulation, thus the application of piezoelectric materials has recently received considerable attention in tissue engineering. This report investigated electrospun fiber meshes based on poly(vinylidenefluoride-co-trifluoroethylene) [P(VDF-TrFE)] as instructive biomaterials for osteogenic differentiation of human mesenchymal stromal cells (hMSCs). The influence played by methyl ethyl ketone (MEK), used as a solvent in place of dimethylformamide (DMF)/acetone mixture, and the effect of rotating velocity of the electrospinning collector on fiber morphology, mechanical and piezoelectric properties were studied. The solvent had noticeable effects on morphology and piezoelectric properties of electrospun fibers, with MEK outperforming DMF/acetone. By increasing the collector velocity up to 4000 rpm, the fiber diameter reduced and the mutual alignment of the fibers increased, corresponding to enhanced mechanical properties and piezo-active β-phase content. However, as a consequence of the diverse mechanical properties of random and aligned fibrous architectures, which ultimately affected the piezoelectric properties, randomly-oriented fibers exhibited higher remnant piezoelectric properties (Vout and d31 piezoelectric coefficient) than aligned ones. On these scaffolds, hMSCs showed an excellent capability of early osteogenic differentiation, leading to high calcium production. Fiber surface topology, fiber mesh morphology and remnant piezoelectric properties played a determinant role on hMSC osteogenic commitment.

Random modeling of hemp fibers mechanical properties

The growing interest in vegetal fiber-based composite materials for reinforcing structural elements is prompting researchers to consider the inherent randomness, arising from various factors which are complex to model. For this reason a general probabilistic approach seems more appropriate to model all uncertainties regardless where they come from. In this paper, factory produced hemp ropes, and their components, are tested to obtain their tensile mechanical properties. In particular, 120 fibers with four different lengths, 55 yarns, 33 strands and 64 ropes are used to obtain a first statistical characterization of tensile strength, strain and Young modulus. These results are used to calibrate two commonly used random models such as Gaussian and three-parameters Weibull distributions and to give both qualitative and quantitative complete random characterization of the tensile properties of each hemp rope components. The obtained results are crucial to estimate vegetal fiber-based composite materials structural response.

Modulating Polyalanine Motifs of Synthetic Spidroin for Controllable Preassembly and Strong Fiber Formation.

Spider dragline (major ampullate) silk is one of the toughest known fibers in nature and exhibits an excellent combination of high tensile strength and elasticity. Increasing evidence has indicated that preassembly plays a crucial role in facilitating the proper assembly of silk fibers by bridging the mesoscale gap between spidroin molecules and the final strong fibers. However, it remains challenging to control the preassembly of spidroins and investigate its influence on fiber structural and mechanical properties. In this study, we explored to bridge this gap by modulating the polyalanine (polyA) motifs in repetitive region of spidroins to tune their preassemblies in aqueous dope solutions. Three biomimetic silk proteins with varying numbers of alanine residues in polyA motif and comparable molecular weights were designed and biosynthesized, termed as N16C-5A, N15C-8A, and N13C-12A, respectively. It was found that all three proteins could form nanofibril assemblies in the concentrated aqueous dopes, but the size and structural stability of the fibrils were distinct from each other. The silk protein N15C-8A with 8 alanine residues in polyA motif allowed for the formation of stable nanofibril assemblies with a length of approximately 200 nm, which were not prone to disassemble or aggregate as that of N16C-5A and N13C-12A. More interestingly, the stable fibril assembly of N15C-8A enabled spinning of simultaneously strong (623.3 MPa) and tough (107.1 MJ m-3) synthetic fibers with fine molecular orientation and close interface packing of fibril bundles. This work highlights that modulation of polyA motifs is a feasible way to tune the morphology and stability of the spidroin preassemblies in dope solutions, thus controlling the structural and mechanical properties of the resulting fibers.

Predicting density-related mechanical properties of amorphous silicon nitride using molecular dynamics simulations

Silicon nitride fiber is among the most popular candidates for high-temperature wave-transparent ceramic matrix composites (CMC) in aerospace engineering, and the measurement of its mechanical properties has always been the focus of researchers. In this paper, a simple and effective molecular dynamics method is used to generate molecular dynamics models of amorphous silicon nitride (a-Si3N4) materials with different densities, and it is verified that the developed models reflect the microstructure of the fiber. Based on analyzing the effects of size on the results, tensile and shear simulations are carried out to obtain the mechanical properties of the models with different densities. According to the research data obtained, the empirical equation between mechanical properties (Young's modulus, shear modulus, tensile strength, and shear strength) and density of fiber is established, and validated by the published experimental results. The empirical equation can not only predict the mechanical properties of fibers directly from the density but also provide a new way to measure the mechanical properties of fibers nondestructively.

The surface treatment of PVA fibres to enhance fibre distribution and mechanical properties of foam concrete

Fibres are often used to improve the mechanical properties of foam concrete. However, the poor dispersion of PVA fibres in foam concrete significantly restricts their reinforcement efficiency. Limited studies have been conducted on improving the distribution of PVA fibres in a cementitious matrix, particularly in relation to foam concrete. This is noteworthy because pore structure, which can be significantly influenced by the fibres and fibre treatment agents, is a critical parameter that affects the mechanical properties of foam concrete. Therefore, this study employed polar agents (non-ionic surfactants) to treat the fibre surface, aiming to enhance the distribution and reinforcement efficiency of PVA fibres in foam concrete. In view of safety and feasibility, two non-hazardous polar agents, namely PEG-PPG-PEG (designated as PA A) and Polyoxyethylene (20) cetyl ether (designated as PA B), were used to treat the PVA fibres. The impact of fibre treatments on fibre dispersion and pore structure was investigated, and the compressive strength and flexural behaviour of foam concrete were measured before and after the treatments. PA A was found to be unsuitable for fibre treatment due to its poor bonding with the fibre surface. On the other hand, PA B exhibited good bonding with PVA fibres, resulting in enhanced fibre dispersion and pore structure in the foam concrete. Compared to plain foam concrete, the fibres treated with PA B increased the compressive and flexural strength by 47.4 % and 190.3 %, respectively. Moreover, the treated fibres (by PA B) were observed to improve the 0.8 mm toughness of foam concrete by 27.2 %.

Investigation of chemical, physical and morpho-mechanical properties of banana-plantain stalk fibers for ropes and woven fabrics used in composite and limited-lifespan geotextile

This study aimed to assess the potential of banana-plantain stalk fibers (BPSF) as a raw material for ropes and fabrics used in composites and geotextiles. Fibers were obtained by Biological retting and ropes used for geotextile weaving were obtained by three-strand twisting in order to optimize the mechanical properties of geostalk. The thermal, physical, chemical and mechanical characteristics of the fibers were studied in order to assess the impact of the extraction process on fiber performance. In addition, the microstructure of fibers and ropes was analyzed using Scanning Electron Microscopy (SEM) and the results highlighted the presence of cellulose microfibrils parallel to fiber axis and hemicellulose linked by lignin matrix. These constituents are organized in three concentric layers around the lumen. Elementary chemical analyses using X-ray energy dispersion (EDS), Fourier Transform Infrared (FTIR) and chemical deconstruction using Jayme-Wise protocol were carried out to determine the chemical composition of BPSF, which consists of 51.5 % Carbon, 47.07 % Oxygen and mineral salts that can be highly contribute to soil fertilization after degradation. These chemical constituents represent 40 % cellulose, 21.5 % hemicellulose, 24 % lignin, 0.34 % pectin, 7.2 % lip soluble extractable and 7.36 % water-soluble sugars present in BPSF. Thermal properties of BPSF have been investigated showing the initial degradation around 200 °C. Physical analysis and uniaxial tensile testing were performed to determine the multi-scale physical and mechanical properties of geostalk. Statistical evaluation using Weibull distribution established an increasing rate of physical and mechanical properties from the finest scale to the macroscopic scale. Thus, from the BPSF to the ropes, titer increases from 42.5 ± 4.5 g/km to 7983.4 ± 132 g/km and elongation at break increases from 0.75 ± 0.29 mm for the fibers to 52.42 ± 18.91 mm for geostalk. With mass per unit area of 1869 g/m2, the tensile stress of 1281.05 ± 273 MPa and maximum strength of 15.4 ± 1.74 kN/m, geostalk is a sustainable woven fabric alternative to geosynthetics for soil reinforcement as other limited lifespan geotextiles (geojute, geocoir and geosisal). In addition, the thermal stability and high mechanical properties of fibers and ropes suggest their potential application as reinforced phases in composite materials.

Interfacial blending in co-axially electrospun polymer core-shell fibers and their interaction with cells via focal adhesion point analysis

Electrospun polymer scaffolds have gained prominence in biomedical applications, including tissue engineering, drug delivery, and wound dressings, due to their customizable properties. As the interplay between cells and materials assumes fundamental significance in biomaterials research, understanding the relationship between fiber properties and cell behaviour is imperative. Nevertheless, altering fiber properties introduces complexity by intertwining mechanical and surface chemistry effects, challenging the differentiation of their individual impacts on cell behaviour. Core-shell fibers present an appealing solution, enabling the control of mechanical properties of scaffolds, flexibility in material and drug selection, efficient encapsulation, strong protection of bioactive drugs against harsh environments, and controlled, prolonged drug release. This study addresses a key challenge in core-shell fiber design related to the blending effect between core and shell polymers. Two types of fibers, PMMA and core-shell PC-PMMA, were electrospun, and thorough analyses confirmed the desired core-shell structure in PC-PMMA fibers. Surface chemistry analysis revealed PC diffusion to the PMMA shell of the core-shell fiber during electrospinning, subsequently prompting an investigation of the fiber’s surface potential. Conducting cellular studies on osteoblasts by super-resolution confocal microscopy provided insights into the direct influence of interfacial polymer blending and, consequently, altered fiber surface and mechanical properties on cell focal adhesion points, bridging the gap between material attributes and cell responses in core-shell fibers.