Fabric Mechanical Properties Research Articles

Assessment of Physical and Mechanical Parameters of Spun-Bond Nonwoven Fabric.

The selection of an appropriate fabric for technical applications, such as protective masks, hinges on a thorough understanding of the fabric's physical and mechanical properties. This study addresses the challenge of selecting the optimal material structure for the upper layer of a protective mask, aiming to ensure adequate breathability while providing effective filtration against airborne particles and contaminants. We assessed and compared the physical-mechanical properties of five polymer spun-bond nonwoven fabrics from different suppliers. Our comprehensive evaluation included, as follows: a visual inspection; light permeability analysis; mass and thickness measurements; elongation and tensile strength tests; breathing resistance assessments; and filter penetration tests with paraffin oil. The results revealed significant variations in performance among the samples, with one fabric consistently outperforming the others across multiple parameters. Notably, this top-performing fabric met or exceeded the EN 149:2001+A1:2009 standard for breathing resistance and filtration efficiency and, in combination with additional filter layers, met the requirements or exceeded class FFP2 (filtering face piece). This study underscores the importance of meticulous material selection and quality control in optimizing PPE (personal protective equipment) performance and user safety, providing valuable insights for mask manufacturers and healthcare professionals.

Stress-strain state of an intraosseous dental implant under stress under unfavorable biomechanical conditions

Biomechanical conditions affect the stress-strain state of teeth, dentures, implants and surrounding tissues, however, some biomechanical processes in implants and covering prosthetic structures have not been sufficiently studied under different operating conditions. The purpose of the study. А comparative analysis of the maximum stresses in titanium implants, abutments and covering ceramic crowns under different biomechanical operating conditions. Material and methods. Three-dimensional mathematical modeling of the stress-strain state of the implant, abutment, crown was carried out using the SolidWork computer program in a model of an implant immersed in a segment of the mandible and covered with a ceramic crown. Load conditions: vertical or inclined 45° with a value of 150 N. Well-known indicators of the physical and mechanical properties of fabrics and structural materials were used. Adverse biomechanical conditions were simulated: a 30% reduction in the length, diameter, length and diameter of the implant; an abutment slope of 15° and 30°; bone resorption by 30% and 50%; increased load by 30%; occlusive supracontact; contact with bone tissue by 50% (immediate load). Results and discussions. In comparison with optimal biomechanical conditions, the stresses in the implant and the covering crown increase under vertical and inclined loads only with an increase in load and the presence of occlusive supracontact. An increase in stresses only in the implant occurs with a decrease in the diameter of the implant, a combined decrease in the diameter and length of the implant, with an abutment tilt, resorption of periimplant bone tissue, incomplete contact of the implant with bone tissue under immediate load. Stress reduction in the implant and the covering crown occurs when the length of the implant decreases. Conclusions. Unfavorable biomechanical conditions in most cases lead to an increase in stresses in the implant, especially with inclined loading; the decrease in stresses in the implant with a decrease in the length of the implant is most likely due to an increase in stresses in the surrounding bone tissue.

A Review of Friction in Low-Stress Mechanics of Fibrous Flexible Materials.

The structure of a fabric is a highly complex assembly of fibres, which have order and regularity as well as disorder and randomness. The complexity of the structure poses challenges in defining its mechanical behaviour, particularly at low stress, which is typical to end uses. The coexistence of multiple deformations and the high degree of nonlinearity of the fabric due to fibre friction make its stress-strain relationship complicated. This article reviews the literature on friction related to the low-stress mechanics of fabrics, and it establishes its range and regularity to help with finding a unified reference model, in which although the physical meanings of fabric tensile, shear, and bending vary, they follow consistent mathematical regularities. So, invariably, their disorder and randomness needed in defining them can be obtained from fabric measurement data. It defines the scope and patterns of friction to facilitate the development of a unified reference model. It argues that although the physical interpretations of fabric tensile, shear, and bending characteristics may differ, they adhere to consistent mathematical regularities within this model, and hence extracting disorder and randomness from fabric measurement data may be achievable. This paper concludes with a number of recommendations, postulating that hysteresis caused by friction between fibres in a fabric is an important component of mechanical information, and it coexists with its purely elastic component, but it cannot be obtained directly by measurement. Seeking means to effectively decompose the friction hysteresis and pure elastic components contained in fabric mechanics measurement data will provide an accurate characterization of fabric mechanical properties and hence an accurate modelling and simulation of its behaviour, and will impact many traditional and industrial textile end uses.

Modelling of Polypropylene Multi-layer Nonwoven Fabrics Techniques and Mechanical Geometrical Properties of Technical Textiles

Modelling of Polypropylene Multi-layer Nonwoven Fabrics Techniques and Mechanical Geometrical Properties of Technical Textiles

Practical Methods to Estimate Fabric Mechanics from Metadata

AbstractEstimating fabric mechanical properties is crucial to create realistic digital twins. Existing methods typically require testing physical fabric samples with expensive devices or cumbersome capture setups. In this work, we propose a method to estimate fabric mechanics just from known manufacturer metadata such as the fabric family, the density, the composition, and the thickness. Further, to alleviate the need to know the fabric family –which might be ambiguous or unknown for nonspecialists–we propose an end‐to‐end neural method that works with planar images of the textile as input. We evaluate our methods using extensive tests that include the industry standard Cusick and demonstrate that both of them produce drapes that strongly correlate with the ground truth estimates provided by lab equipment. Our method is the first to propose such a simple capture method for mechanical properties outperforming other methods that require testing the fabric in specific setups.

Determining Tactile Comfort of Cellulose-Based Woven Fabrics, Knitted Fabrics and Terry Towels Using a Novel Instrument

ABSTRACT In this study, tactile comfort of woven bed sheets, terry towels, and weft knitted fabrics made of cotton and blends was investigated. Tactile Sensation Analyzer (TSA) was used for determining surface characteristics and low-stress mechanical properties of fabrics. Micro and macro-surface variations were determined via a special sound analysis technique, and low-stress mechanical properties (deformation, elasticity, hysteresis, and plasticity) were measured in out-of-plane deformation state. Total hand (TH) scores of fabrics were determined by expert assessors via sensory tests. Findings of the study revealed that surface and low-stress mechanical properties measured using TSA were strongly and significantly correlated with sensory evaluation results in general. It was detected that tactile comfort of knitted fabrics and towels was strongly related to the magnitude of macro-surface variations; meanwhile, micro-surface variations were found out to be a more determinant parameter for bed sheets. It was observed that deformation and recovery characteristics of bed sheets and towels have a significant effect on TH scores as well. Hand of fabrics was also investigated by a conventional nozzle test equipment for comparison purposes, and it was detected that TSA results can represent fabric hand better than the raw data obtained from the nozzle test equipment.

Efficient anti-fibrillation of lyocell fabric by low-formaldehyde resin

Lyocell fiber is a green kind of renewable cellulose fiber derived from plants and has many excellent properties. However, in the process of production and application of lyocell fiber, due to swelling and external force, it is easy to produce a serious fibrillation phenomenon. The phenomenon of fibrillation has a very serious impact on the quality and application of lyocell products. To solve this problem, a simple and efficient anti-fibrillation treatment technique was explored in this work. The treatment of lyocell fabric with etherification modified dimethylol dihydroxy-ethylene-urea (ultra-low formaldehyde 2D resin) can enhance the lateral interaction force between the macromolecular chains of lyocell fiber and enhance the anti-fibrillation performance of lyocell fiber. The reaction mechanism between ultra-low formaldehyde 2D resin and lyocell cellulose chain was determined by measuring the fabric mechanical properties, fiber swelling degree, chemical element content, and Fourier transform infrared spectroscopy (FTIR). When the finishing solution contained 100 g/L resin and 20 g/L catalyst with pH 3, after the fabric was cured under 160 ℃ for 60 s, the fibrillation phenomenon of the fiber was greatly reduced. After the treatment of the fabric, its mechanical properties were basically not affected. There was a slight decrease in strength, and the hydrophilic properties were not affected obviously. Compared with the traditional rolling-drying-baking process, this method not only has a shorter and simpler process flow but also has less influence on fabric properties, which guaranteed the smooth progress of the subsequent production and application.

The Influence of Textile Type, Textile Weight, and Detergent Dosage on Microfiber Emissions from Top-Loading Washing Machines.

The use of washing machines to wash textiles gradually breaks down synthetic fibers like polyethylene terephthalate (PET) or polyester (PES) in diverse clothing materials, a process that is growing in notoriety because it generates microplastics (MPs). In this study, we investigated the emission of microfibers, including both microplastic fibers (MPFs) and natural fibers (MFs), from top-loading washing machines. Our investigation focused on four popular textiles with prevalent weave structures (plain, satin, and twill): (i) PES, (ii) tetron cotton (TC), (iii) chief value cotton (CVC), and (iv) cotton (CO) fabrics. This study also examined the effects of textile weight and detergent dosage on MF emissions. After washing, MFs were collected through filtration, and their concentrations were determined using micro-Fourier Transform Interferometry (μFTIR). The results showed varying concentrations of MFs in the washing effluent depending on the type of textile. Specifically, CVC exhibited the highest emission at 4022 particles/L, followed by TC, PES, and CO at 2844 particles/L, 2382 particles/L, and 2279 particles/L, respectively. The hydrophobic nature of PES makes this type of textile prone to rapid degradation in detergent-rich environments, leading to high MF emissions. Additionally, the mechanical properties of textiles, such as tensile and bending strengths, may play a crucial role in the generation of MFs in washing machines. Textiles made of CO with twill weaves demonstrated superior strength and correlated with lower emissions of MFs. In comparison, textiles made of CVC and satin weave exhibited lower mechanical properties, which could explain their high emissions of MFs. Finally, the MF emissions of textiles composed of PES and TC, which are plain weaved, could be attributed to their intermediate mechanical properties compared with those of CVC and CO.

A One-Step Approach for a Durable and Highly Hydrophobic Coating for Flax Fabrics for Self-Cleaning Application.

Highly hydrophobic flax fabrics with durable properties were prepared using the "dip-coating" method for self-cleaning application. Flax fabrics were coated with a polysiloxane coating via a hydrosilylation reaction with a Karstedt catalyst at room temperature. The coated fabrics displayed highly and durable hydrophobic properties (contact angle and sliding angle of about 145° and 23°, respectively) with good self-cleaning ability for certain pollutants and excellent durability. Moreover, the influence of the coating process on the mechanical properties of fabrics was investigated. A decrease in E modulus and an increase in tensile stress at maximum force and elongation at maximum force has been observed. Furthermore, this influence of the coating process can be easily controlled by adjusting the proportion of curing agent in the treatment solution.

Tannins as Biobased Molecules for Surface Treatments of Flax Wrapped Rovings for Epoxy/Flax Fabrics Biocomposites: Influence on Mechanical Properties through a Multi-Scale Approach

The present study examined the effect of biobased molecules grafted onto wrapped flax rovings on the mechanical properties of fabrics designed for epoxy-based biocomposites, aiming to optimize fiber/matrix adhesion. Biobased solutions, such as tannins from quebracho, were used to treat wrapped flax rovings in comparison to a non-biobased aminosilane solution used as a reference. The chemical treatment is performed using an innovative lab-scale impregnation line. The influence of the solution concentration has been investigated. SEM-EDX and FT-IR confirmed the grafting efficiency of molecules on wrapped rovings. Plain and 5-harness satin fabrics were then manufactured at lab scale with the resulting functionalized rovings. Tensile tests were carried out on rovings and on fabrics. A concentration of 1% silane is sufficient to improve the mechanical properties of rovings and fabrics. The addition of NaOH to tannins strengthens flax fiber rovings more than tannins alone, and the weave pattern influences mechanical performance.

A review of aluminum metal matrix composites: fabrication route, reinforcements, microstructural, mechanical, and corrosion properties

A review of aluminum metal matrix composites: fabrication route, reinforcements, microstructural, mechanical, and corrosion properties

Spider-Silk-like Fiber Mat-Covered Polypropylene Warp-Knitted Hernia Mesh for Inhibition of Fibrosis under Dynamic Environment.

Hernia surgery is a widely performed procedure, and the use of a polypropylene mesh is considered the standard approach. However, the mesh often leads to complications, including the development of scar tissue that wraps around the mesh and causes it to shrink. Consequently, there is a need to investigate the relationship between the mesh and scar formation as well as to develop a hernia mesh that can prevent fibrosis. In this study, three different commercial polypropylene hernia meshes were examined to explore the connection between the fabric structure and mechanical properties. In vitro dynamic culture was used to investigate the mechanism by which the mechanical properties of the mesh in a dynamic environment affect cell differentiation. Additionally, electrospinning was employed to create polycaprolactone spider-silk-like fiber mats to achieve mechanical energy dissipation in dynamic conditions. These fiber mats were then combined with the preferred hernia mesh. The results demonstrated that the composite mesh could reduce the activation of fibroblast mechanical signaling pathways and inhibit its differentiation into myofibroblasts in dynamic environments.

Algorithmic Information Theory for the Precise Engineering of Flexible Material Mechanics

The structure of fibrous assemblies is highly complex, being both random and regular at the same time, which leads to the complexity of its mechanical behaviour. Using algorithms such as machine learning to process complex mechanical property data requires consideration and understanding of its information principles. There are many different methods and instruments for measuring flexible material mechanics, and many different mechanics models exist. There is a need for an evaluation method to determine how close the results they obtain are to the real material mechanical behaviours. This paper considers and investigates measurements, data, models and simulations of fabric’s low-stress mechanics from an information perspective. The simplification of measurements and models will lead to a loss of information and, ultimately, a loss of authenticity in the results. Kolmogorov complexity is used as a tool to analyse and evaluate the algorithmic information content of multivariate nonlinear relationships of fabric stress and strain. The loss of algorithmic information content resulting from simplified approaches to various material measurements, models and simulations is also evaluated. For example, ignoring the friction hysteresis component in the material mechanical data can cause the model and simulation to lose more than 50% of the algorithm information, whilst the average loss of information using uniaxial measurement data can be as high as 75%. The results of this evaluation can be used to determine the authenticity of measurements and models and to identify the direction for new measurement instrument development and material mechanics modelling. It has been shown that a vast number of models, which use unary relationships to describe fabric behaviour and ignore the presence of frictional hysteresis, are inaccurate because they hold less than 12% of real fabric mechanics data. The paper also explores the possibility of compressing the measurement data of fabric mechanical properties.

Influence of Novel SrTiO3/MnO2 Hybrid Nanoparticles on Poly(methyl methacrylate) Thermal and Mechanical Behavior.

While dental poly methyl methacrylate(PMMA) possesses distinctive qualities such as ease of fabrication, cost-effectiveness, and favorable physical and mechanical properties, these attributes alone are inadequate to impart the necessary impact strength and hardness. Consequently, pure PMMA is less suitable for dental applications. This research focused on the incorporation of Strontium titanate (SrTiO3-STO) and hybrid filler STO/Manganese oxide (MnO2) to improve impact resistance and hardness. The potential of STO in reinforcing PMMA is poorly investigated, while hybrid filler STO/MnO2 has not been presented yet. Differential scanning calorimetry is conducted in order to investigate the agglomeration influence on the PMMA glass transition temperature (Tg), as well as the leaching of residual monomer and volatile additives that could pose a threat to human health. It has been determined that agglomeration with 1 wt% loading had no influence on Tg, while the first scan revealed differences in evaporation of small molecules, in favor of composite PMMA-STO/MnO2, which showed the trapping potential of volatiles. Investigations of mechanical properties have revealed the significant influence of hybrid STO/MnO2 filler on microhardness and total absorbed impact energy, which were increased by 89.9% and 145.4%, respectively. Results presented in this study revealed the reinforcing potential of hybrid nanoparticles that could find application in other polymers as well.

Biomedical therapeutic compression textiles: Physical-mechanical property analysis to precise pressure management

Biomedical therapeutic compression textiles (TCTs) have been extensively applied in the prevention and treatment of chronic venous insufficiency of lower extremities. An efficiency and operable development strategy to achieve the morphologic control and pressure fitness of TCTs needs to be proposed to improve the medical precision and patient adherence. Therefore, the present study qualitatively explored the influencing mechanisms of each knitting variable on physical-mechanical properties and pressure behaviors of TCTs. Then constructed the quantitative models to digitalize the knitting variables for determination of yarn-machinery setting design values. The results revealed that the feeding velocity of elastic inlay yarn materials and loop size settings impacted the pressure values owing to the diversities of fabric dimensions and mechanical tensile properties, respectively. Simultaneously, the derivation ratios of proposed circumferential and pressure models evaluated by experimental validated trials were approximately 1.1% and 10.8%, respectively. This study provided the fundamental references for the design, manufacturing, and property controlling of compression textiles to improve the biomedical therapeutic effectiveness for targeted users.

Fabrication, microstructure and multi-scale mechanical properties of 2.5D oxide fiber reinforced oxide composites

2.5D oxide/oxide composites have attracted substantial attention due to their good integrity. In this work, a simple process was used to manufacture the 2.5D aluminosilicate fiber reinforced alumina (2.5D-ASf/Al2O3) composites. The influence of 2.5D preform on the microstructure of the 2.5D-ASf/Al2O3 composite was studied in-depth mainly by X-ray computed tomography. Also, the change mechanism of the micro- and macro- mechanical properties of composites, especially the anisotropic mechanical properties were further analyzed. The results showed that the matrix modulus and fiber strength had great effects on the mechanical properties of the 2.5D-ASf/Al2O3 composites with different densification cycles. And the microstructure characteristics of the 2.5D-ASf/Al2O3 composites were consistent with those of the 2.5D preform, such as the warp direction cross-sections invariably had higher porosity of the pores>10 μm and larger pores than the weft direction cross-sections. This was also one of the key factors affecting the anisotropic mechanical behavior of the 2.5D-ASf/Al2O3 composites.

Development of a multi-layered waterproof breathable fabric for full-weather apparel

In this research, a laminate was produced by assembling five textile layers. These layers were a coated double-sided knitted structure, a non-woven fabric, a hydrophilic membrane that was thermally assembled to a surface veil, and an open-work knitted fabric. The laminated textile's breathability, windproofness, and waterproofness were evaluated. The multi-layered fabric was windproof, and its water vapor permeability was 347.297 g?m-2?s-1 (CV= 8.902%). Its resistance to water penetration was equal to 117.68 Schmerber (CV = 7.81%). The assembled fabric's mechanical properties were also evaluated. Young?s modulus values were equal to 2 MPa (CV= 8.613%) and 1.6 MPa (CV= 8.349%) for both fabric directions. Its flexural rigidity was 5056.659 mg?cm and its surface total deformation was lower than 450 ?m when measured under 20, 40, 60, and 80 mN loads. Based on the results obtained, it was concluded that the developed multi-layered fabric could be used to produce raincoats and jackets to protect the wearer from light rain and drizzle.

Rapid fabrication of porous metakaolin-based geopolymer via microwave foaming

Microwave foaming was used for the first time to rapidly fabricate the metakaolin-based porous geopolymers. Mechanical, thermal, and microstructural (optical and scanning electron microscope) investigations coupled with X-ray diffraction, Fourier-transform infrared spectroscopy, and nuclear magnetic resonance techniques were conducted to characterize the obtained foams. High porosity metakaolin-based porous geopolymers could be obtained at 4 min of foaming/curing. The effect of the sodium silicate solution content on the total porosity as well as the mechanical and thermal properties was investigated. The total porosity decreased firstly and then increased in the range of ∼74 to ∼84 vol% with the increase of Na2SiO3 content. The foams with 47.7 wt% Na2SiO3 exhibited the lowest thermal conductivity (0.104 W/mK) and the highest total porosity (83.2 vol%). The fabrication time, mechanical, and thermal properties were compared with those of foams obtained by the conventional direct foaming method. With this approach, the preparation time can be greatly reduced, and the compressive strength (1.89–2.04 MPa) and thermal conductivity (0.104–0.155 W/mK) of the materials obtained were not inferior to similar components obtained by other foaming routes. The rapidly obtained porous geopolymers with high porosity and high strength as well as low thermal conductivity can be employed as thermal insulation materials and ceramic precursors.

Cellulose nanofiber-introduced continuous-ramie yarn-reinforced polylactic acid filament for 3D printing: Novel fabrication process and mechanical properties

This study focused on reinforcing the interface of continuous-ramie yarn-reinforced polylactic acid (PLA) filaments with cellulose nanofibers (CNFs) for 3D printing applications. To realize the reinforcement effect of CNFs, the distribution of dispersed CNFs at the surface of ramie fiber is necessary. Thus, we developed a new false-untwisting process to enable the continuous dip-coating of CNF slurry while the ramie yarn is untwisted yarn. This study was designed to reveal the influence of the false-untwisting process and CNF content on the surface morphology of the processed yarn and on the mechanical properties of the yarn–PLA composite filaments. We found that the false-untwisting process achieved the formation of fuzzy CNFs. Furthermore, the tensile strength and Young’s modulus of the filaments were improved by up to 20.0% and 26.6%, respectively, compared to those of ramie yarn-reinforced PLA filaments without CNFs.

Investigation of the dyeability and various performance properties of fabrics produced from flax and hemp fibres and their blends with cotton in comparison with cotton

AbstractIn this study, it is aimed to provide alternative fibres to cotton with enhanced comfort level, environmentally friendly and colour‐enriched in the cellulosic knitted fabric field. For this purpose, in addition to 100% cotton, 100% linen, 100% hemp yarns, knitted fabrics were produced from 70% cotton/30% linen and 70% cotton/30% hemp yarns. First of all, the properties of yarns such as tenacity, elongation at break, yarn unevenness, thin places, thick places and neps were examined comparatively. Then, pique fabrics were produced from these yarns and dyed with a reactive dye to a selected colour. Afterwards, physical (weight, wale/course density), mechanical (bursting strength, pilling, abrasion resistance) and comfort (air permeability and water vapour permeability) properties of all fabric samples, both in raw form and after dyeing and finishing processes, were compared. Furthermore, dyeing properties (colour, dye‐uptake, dyeing levelness, fastness) of fabric samples were also investigated. The dye uptake (%) values of the yarns decrease in the order of cotton > cotton/hemp > cotton/linen > hemp > linen. However, fastness values of dyed fabrics were nearly identical. Physical and mechanical properties of fabrics were very similar, while the air permeability of the fabrics decrease in the order of hemp > linen > cotton/hemp > cotton/linen > cotton. As a result of the study, it has been possible to produce knitted fabrics with superior performance characteristics (dyeability, comfort, etc.) from yarns produced via blending natural cellulosic fibres (flax and hemp) with certain proportions of cotton fibres, which contribute to sustainable production.