Types Of Materials Research Articles

Sideband Peak Count – a new nonlinear ultrasonic technique for monitoring damage progression in engineering materials

Linear ultrasonic (LU) techniques used by majority of the researchers working in material damage monitoring, are reliable for detecting relatively large defects. If the defect dimensions are in the range of the ultrasonic wavelength or larger, then those defects can be detected by analyzing the scattered ultrasonic fields. Material damage affects LU parameters such as ultrasonic wave speed and attenuation and their changes are detectable for relatively large defects. However, for small defects (when defect dimensions are significantly smaller than the wavelength of the propagating signal) the changes in the LU parameters are too small to detect or measure reliably. For detecting small defects engineers often use high frequency ultrasonic signals to make the defect dimensions greater than the wavelength. However, high frequency signals attenuate quickly and therefore, only very small regions near the ultrasonic probe can be inspected in this manner. Inspecting large structures by high frequency ultrasonic signals requires moving the probe mechanically from one point to the next and therefore, can be very time consuming. Nonlinear ultrasonic (NLU) technique on the other hand does not need to satisfy this restricting condition that the wavelength of the signal must be smaller than the defect size. NLU works well when the signal wavelength is much larger than the defect size. Therefore, relatively low frequency signals that can propagate a long distance and monitor a large area of a structure can be used for NLU measurements. Different NLU techniques can be used for detection and monitoring of small damages in a specimen. A relatively new NLU technique called the Sideband Peak Count-Index or SPC-I technique has been developed by the author and his collaborators. SPC-I technique for monitoring different types of materials – composites, metals, concrete, and other cement-based materials has been found to be effective. Along with those success stories of SPC-I the effect of topography and the advantage of topological sensing is also discussed in this presentation.

Development and thermal property analysis of biobased binary composite heat storage materials

Natural aliphatic dibasic acids are a type of bio-based material that shows promising potential as green phase change thermal storage materials due to their favorable thermophysical properties. However, these materials have been found to have issues with subcooling, low thermal conductivity, and poor temperature matching. In this study, three aliphatic dibasic acids, namely adipic acid (AA), sebacic acid (SA), and azelaic acid (ZA), were selected for further investigation. Three biobased eutectic systems, AA-SA (melting point: 118.3 °C), ZA-SA (melting point: 96.2 °C), and AA-ZA (melting point: 98.4 °C), were then prepared based on the calculation of Schrader's equation and experimental screening. The eutectic systems were thoroughly characterized, revealing thermal conductivities ranging from 0.4 to 0.5 W·m−1·K−1, with all systems exhibiting a subcooling of around 20 °C. Based on the principle of optimal overall performance, the AA-SA system was selected for modification. By incorporating Expanded graphite (EG) as a highly thermally conductive additive and nucleating agent, the AA-SA/EG composite phase change material (CPCM) was successfully prepared. This modification effectively reduced the supercooling degree of the bio-based phase change materials (PCM) and significantly improved its thermal conductivity by a factor of four. The resulting AA-SA/EG CPCM demonstrated excellent temperature suitability and has the potential to contribute to the application of bio-based phase change materials in waste heat recovery and solar energy systems. This study provides valuable insights into the development and optimization of bio-based phase change materials, contributing to the sustainable utilization of renewable resources for thermal energy storage applications.

Visualization of Solvent Effect and Oxygen Content via a Red Room-Temperature Phosphorescent Material.

The development of pure organic room-temperature phosphorescent (RTP) materials greatly facilitates the integrated application of luminescent materials. Herein, a type of photoactivated red RTP material was constructed by simply doping 4-(benzo[c][1,2,5]thiadiazol-5-ylthio)benzonitrile (p-NNS) into a poly(methyl methacrylate) (PMMA) matrix. The obtained film realized a controllable photoactivation process by regulation of diverse solvent levels, demonstrating potential advantages in optical anti-counterfeiting applications. Furthermore, luminescent properties of the doped film were utilized to detect oxygen content from 2.00% to 4.90%, which revealed the exact consumption of ambient oxygen under UV light. Every CIE point of the luminescence corresponds to a certain oxygen content, illustrating the visualization of oxygen content. The remarkable regulation of solvent effect and oxygen content in this work will provide competitive material for further optical applications.

Ultrafast, Selective, and ppb Level In Vitro Electrochemical Sensing of Dopamine in a Simulated Interfering Environment: Comparative Study on the Effect of Carrier Type of Electrode Materials

Ultrafast, Selective, and ppb Level In Vitro Electrochemical Sensing of Dopamine in a Simulated Interfering Environment: Comparative Study on the Effect of Carrier Type of Electrode Materials

The study of electrochemical stabilization mechanism of Pt, GC, SS304, Ti and Cu as current collectors for aqueous lithium-ion batteries by electrochemical approaches

This paper employs electrochemical methods (linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS)) to investigate the electrochemical behavior of platinum, glassy carbon, 304 stainless steel, titanium, and copper in 21 and 1 M LiTFSI electrolytes. The LSV results indicate that the electrochemical stability window of the materials varies with the electrolyte concentration, and the stability window is wider in the high-concentration system. Through Tafel polarization curves and EIS analysis, the overpotential of the charge exchange process differs due to the type of material and the concentration of the electrolyte, mainly attributed to the influence of the proportion of free water, electrolyte viscosity, and SEI film formation on electrode process kinetics. After comparative analysis, glassy carbon exhibits a higher overpotential than other materials at both the cathode and anode, effectively suppressing water decomposition. These findings provide theoretical support for the development of high-performance aqueous lithium-ion battery current collector materials.

Polar Alternating Cations Intercalated Hybrid Perovskite with Iodine‐Substituted Spacers Toward Efficient Passive X‐Ray Detection

Abstract2D hybrid perovskites, with their high X‐ray absorption and extended carrier transport, present excellent promise for efficient direct X‐ray detection. However, most of the current devices require external bias voltage, which results in the need for significant energy consumption and severe ion migration, therefore, it is urgent to develop new types of materials for achieving efficient passive X‐ray detection. Herein, two novel chiral polar alternating cations intercalation (ACI)‐type hybrid perovskite materials, named (R/S‐PPA)(IEA)PbBr4 (1‐R/S, (R/S)‐PPA = R/S‐1‐phenylpropylamine; IEA = iodoethylamine), are constructed by integrating the chiral aromatic spacer R/S‐PPA and the iodine‐substituted spacer IEA. Various intermolecular interactions, such as I···I, C─H···I, π···π interactions, are introduced due to the introduction of I‐substituted chain amines, which effectively suppresses ion migration and thus lead to improved operational stability. The device constructed along the polar axis displays superior X‐ray detection performance, such as relatively high sensitivity and an ultra‐low limit of detection (LoD) of 3.0 nGy s−1, making it the first chiral ACI‐type perovskite material for realizing efficient passive X‐ray detection. Furthermore, 1‐R also presents low dark current drift and exceptional irradiation stability. This work provides new thought for using novel ACI‐type polar perovskite for high‐performance passive direct X‐ray detection.

Monomer elution and shrinkage stress analysis of addition-fragmentation chain-transfer-modified resin composites in relation to the curing protocol

ObjectiveThe purpose was to compare the effects of rapid (3s) and conventional (20s) polymerization protocols (PP) of mono- and multichip LED curing units (LCU) on shrinkage stress (SS) and monomer elution (ME) in bulk-fill resin-based composites (RBC) with and without addition-fragmentation chain-transfer (AFCT) monomer. MethodsCylindrical (5x4mm) specimens were prepared from two RBCs containing different AFCT monomers (Filtek OneBulk-FOB; Tetric PowerFill-TPF) and one without (Tetric EvoCeram Bulk-TEC). After soaking for 3, 10, and 14 days (75% ethanol), ME was quantified using standard monomers by High-Performance Liquid Chromatography. SS was measured from the start of polymerization to 5min using a Materials Testing Machine. The radiant exitance of LCUs was measured using a spectrophotometer. ANOVA and Tukey's post-hoc test, multivariate analysis and partial eta-squared statistics were used to analyze the data (p < 0.05). ResultsAFCT-modification significantly decreased ME (p<0.001). ME was reduced by half by day 10 and by one tenth by the end of the 14-day compared to the 3-day sampling. ME itself was dependent, whereas the percentage of monomers released was independent of the PP used (p>0.05). FOB showed the lowest SS (p<0.001), while there was no significant difference between TPF and TEC (p=0.124). Both ME and SS were significantly influenced by material type and PP. SignificanceThe incorporation of the AFCT monomer reduced ME, but this was inversely related to a decrease in exposure time. SS values reduced by rapid PP in parallel with increasing ME values. The utilization of the AFCT molecule in conjunction with an appropriate resin-, initiator-system is of significant consequence for the kinetics of polymerization and the incorporation of monomers into the network.

Fine Structure and Electrochemical Performance Investigations of Spherical LiMn0.6Fe0.4PO4/C Cathode Material Synthesized via a Spray-Drying Route at Various Calcination Temperatures.

LiMnxFe1-xPO4/C is characterized by excellent multiplicative performance and high operating voltage, and as a type of cathode material, it has a high electronic conductivity and thus has received much attention. In this paper, carbon-coated LiMn0.6Fe0.4PO4/C was synthesized using glucose + PEG2000 as the carbon source by wet sanding and spray-drying. The experimental results show that the use of sanding and the spray-drying method can make the particle size distribution of LiMn0.6Fe0.4PO4/C powder more uniform. The initial discharge specific capacity of the LiMn0.6Fe0.4PO4/C battery was 144.3 mA h g-1, and after 100 cycles at 1 C current, the discharge specific capacity of the battery remained at 128.2 mA h g-1 with a cycling efficiency of 94.3%. At the same time, the oxidation states and coordination environments of the elements Fe and Mn were elucidated by X-ray absorption fine structure spectroscopy. And the ex-Fe-MS was tested under different charging and discharging conditions. The sample optimized by the orthogonal test has good cycle stability and multiplication performance.

Thermal Properties of 3D-Printed Molds for Light Metal Casting

AbstractBinder Jetting technology is well established for the production of sand molds and cores for foundry use, owing to its flexibility and expansive design capabilities. A wide array of sand, aggregate, and binder combinations is commercially available. Utilizing these types of refractory materials in the casting process presents both technical and economic benefits and drawbacks. For intricate cast components, foundry technologists must assess the thermophysical properties of the mold material systems. With this knowledge, specialized high-performance material combinations may be employed in specific areas of the mold, while more economically viable systems are used for shaping the external mold support. This study primarily focuses on determining the heat capacity and thermal diffusivity and consequently the thermal conductivity using a specially developed analytical method. It investigates three different fundamental aggregates: silica, cerabeads®, and chromite. The result’s range provides an overview of relevant characteristics for the selected material systems. Given that the properties of sand affect heat flow during casting and solidification, these newly determined values can be utilized in future simulations. Consequently, these findings aid in maintaining and enhancing the quality of critically stressed cast parts.

An experimental investigation on transpiration cooling with phase change subjected to non-uniform flame

Transpiration cooling with phase change is promising for thermal protection of scramjet engine due to the combined advantages of latent heat absorption of coolant and thermal insulation of gas film. Previous investigations primarily focused on the transpiration cooling subjected to uniform incoming flow. However, few investigations have revealed the effect of the non-uniformity of high-temperature flame on transpiration cooling with phase change. Moreover, the effect of porosity on transpiration cooling performance was seldomly mentioned. Herein, we experimentally investigate the transpiration cooling in porous media of alloy (Inconel 600) with deionized water as the coolant subjected to the non-uniform high-temperature flame. Moreover, the effects of porosity and type of transpiration material on cooling are investigated. Results show that when the injection rate is less than 16 %, local overheating occurs on the surface of the porous materials. The overheating phenomenon occurs earlier at lower injection rates. Moreover, the decrease in porosity of the transpiration material will lead to increases of the surface temperature and top/back surface temperature difference, as well as decreases of top-surface temperature non-uniformity and cooling efficiency. In addition, for the different porous materials with similar thermal conductivity, the specific surface area exhibits a dominant factor in transpiration cooling.

Thermoelectric properties of reduced TiO2 -SrF2 composites

Highly stable thermoelectric materials based on inexpensive elements have great potential for heat recovery in high temperature applications. TiO2-d and SrTiO3 based thermoelectric materials are of great interest due to this reason. In this study TiO2–SrF2 based compounds were produced, to study the effect of fluorine on the thermoelectric properties of TiO2 type materials. From XPS measurements it is clear that some exchange from the TiO2–SrF2 happens forming a TiOxFy type phase. The electronic properties of the compound are very similar to the electronic properties of reduced TiO2 while some improvement is seen in the reduction of the thermal conductivity. A higher activation energy in the SrF2 rich samples might allow for increased electronic conductivity at higher temperatures interesting for further studies.

Synthesis and Investigation of ReSe2 Thin Films Obtained from Magnetron Sputtered Re and ReOx

The promise of two-dimensional (2D) rhenium diselenide (ReSe2) in electronics and optoelectronics has sparked considerable interest in this material. However, achieving the growth of high-quality ReSe2 thin films on a wafer scale remains a significant challenge. In this study, we adopted a two-step method to produce ReSe2 thin films by combining magnetron sputtering of Re and ReOx onto flat substrates with subsequent selenization via atmospheric pressure chemical vapor transport (CVT). After analyzing the produced films using X-ray diffraction to identify the crystalline phase in formed thin film and scanning electron microscopy (SEM) to examine surface morphology, it was determined that the suitable temperature range for the 15 min selenization process with CVT is 650 °C–750 °C. Further investigation of these optimally produced ReSe2 thin films included atomic force microscopy (AFM), X-ray photoelectron spectroscopy, and Raman spectroscopy. The bulk electrical analysis of these films and AFM and SEM surface morphology revealed a strong reliance on the type of precursor material used for their synthesis, whereas optical measurements indicated a potential for the films in non-linear optics applications, irrespective of the precursor or temperature used. This study not only provides a new pathway for the growth of ReSe2 films but also sheds light on the synthesis approaches of other 2D transition metal dichalcogenide materials.

Characterization of EJ-270 and Ce-doped LiCAF scintillators for the development of high-rate neutron reflectometer detectors

The Second Target Station of the Spallation Neutron Source at Oak Ridge National Laboratory is anticipated to provide a neutron source with ∼20 times increase in peak brightness than the First Target Station. The neutron reflectometers currently in operation at the First Target Station need to be upgraded due to the increased neutron flux. A prototype neutron detector module based upon a pixelated scintillator array readout by silicon photomultipliers is being developed to address the high-rate challenge faced with future neutron reflectometer instruments at the Second Target Station. Two types of scintillator materials were considered for this detector development, i.e., 6Li-loaded EJ-270 plastic scintillator and Ce-doped LiCAF single crystal. This paper reports the scintillator characterization results, including light yield, pulse shape discrimination performance, capability to detect thermal neutrons in a high γ-ray field, and γ-ray sensitivity. The number of photons produced per neutron capture by EJ-270 and LiCAF:Ce was measured to be 2176 ± 91 and 2651 ± 108, respectively. EJ-270 demonstrated a good capability to discriminate between neutrons and γ-rays by employing the commonly used charge comparison method (figure-of-merit: 1.13 ± 0.01 for an energy cut of 292–426 keVee) and a reasonable performance when using the time-over-threshold techniques; however, no discrimination was observed from LiCAF:Ce regardless of the pulse shape discrimination approaches utilized, making pulse height discrimination necessary for LiCAF:Ce to differentiate between neutrons and γ-rays. Both EJ-270 and LiCAF:Ce exhibited an acceptable capacity to detect thermal neutrons at high exposure rates up to approximately 584 mR/h. The γ-ray sensitivities measured with a60Co source at an exposure rate of around 1145 mR/h were determined to be (6.11 ± 0.87) × 10−6 and (7.64 ± 1.08) × 10−7 for EJ-270 and LiCAF:Ce, respectively.

Green electrosynthesis of bis(indolyl)methane derivatives in deep eutectic solvents

In this study, a new green method was developed for the synthesis of bis(indolyl)methane derivatives using electrochemical bisarylation reaction in deep eutectic solvents as a green alternative to traditional solvents and electrolytes. The effects of varying time, current, type of solvent and material of electrodes were all studied. The optimum reaction conditions involved the use of ethylene glycol/choline chloride with a ratio of 2:1 at 80 °C for 45 min. Graphite and platinum were used as cathode and anode, respectively. The newly developed method offered many advantages such as using mild reaction conditions, short reaction time and affording high product yields with a wide range of substituted aromatic aldehydes bearing electron donating or electron withdrawing substituents. In addition, the electrochemical method proved to be more effective than heating in deep eutectic solvents and afforded higher yields of products in shorter reaction time. The mechanism of the electrochemical reaction was proposed and confirmed using the cyclic voltammetry study.

Production of lignin-containing nanocellulose from six types of unpretreated lignocellulosic biomass by a one-step process

Lignin-containing nanocellulose (LCN) shows great potential in the fabrication of high performance bio-based materials, and suitable raw materials may achieve the production of LCN in a more economical approach. Therefore, in this study, the morphology, chemical and supramolecular structure of six types of lignocellulosic biomass (Broussonetia papyrifera bark, moso bamboo, rattan, balsa wood, poplar wood and fir wood) were analyzed for the production of LCN by using pure oxalic acid dihydrate (OAD). The results revealed that BPBs is a natural available cellulose-rich materials with extremely high cellulose content, low lignin content, and loosely connected cellulose chains. Compared with the other five types of lignocellulosic biomass materials, the hydrolysis of BPBs without any pretreatments by using OAD produced higher yield of LCN with much more uniform size distribution and smaller size. LCN from BPBs had higher crystallinity and thermal stability than that from the other five lignocellulosic biomass. The finding in this study indicated that Broussonetia papyrifera bark without any pretreatment was a favored material for high yield production of LCN compared with the other woody materials, which provided an economically realizable method on the efficient and high yield production of LCN from unpretreated BPBs by using OAD hydrolysis.

Epitypification and emended description of Cyclotella hubeiana, a centric diatom from Central China, with remarks on its distribution and ecology

Since its description by Chen and Zhu in 1985 from samples collected in a river and reservoir from Hubei Province (Central China), Cyclotella hubeiana has been reported from several sites in central and southern China. Only line drawings were provided with the original description and the same drawings were used in the subsequent diatom floras from China. The more recent reports of this species come from limnological studies which generally do not provide illustrations. There is therefore a need to better illustrate this taxon. As the type material could not be retrieved, new material was collected from the type locality (Xionghe Reservoir) to elucidate its ultrastructure using light and electron microscopy. The figures published by Chen and Zhu in 1985 are designed as lectotype and the new material as epitype to the lectotype. Characteristics of the valve such as the position of the rimoportula (on a costa, within the ring of marginal fultoportulae) and the absence of central fultoportulae on the valve face suggest that this species is best placed within the genus Cyclotella as presently defined. Its morphology is compared with similar species of Cyclotella and Pantocsekiella. In addition, in a study on Qiandao Lake, a reservoir from Zhejiang Province (eastern China), a large population of this taxon was found in down-core assemblages within 20 years of the reservoir being impounded. This abundant material allowed a better assessment of the size range and morphological variability of this species. Besides emending the description and validating the taxonomic status of this species, this study also discusses its ecology and distribution.

Soy Protein-Based Wound Dressings: A Review of Their Preparation, Properties, and Perspectives.

Wound healing is a major challenge worldwide, and people have been researching wound dressings that can promote wound healing for decades. Natural biobased materials, such as polysaccharides and proteins, have been widely used in the development of wound dressings. Among them, soy protein-based materials have attracted the interest of a wide range of researchers due to their safety, biocompatibility, controlled degradation, and ability to be mixed with other materials. However, there has been a lack of comments on these soy protein-based wound dressings. This work reviews various forms of soy protein-based wound dressings, such as hydrogels, films, and others, which could be prepared through physical/chemical cross-linking with synthetic or natural polymers. The important role played by soy protein-based materials in the wound healing phase and their properties will be examined, such as their anti-inflammatory, antioxidant, angiogenesis-promoting, cellular biocompatibility, self-healing ability, adhesion, antimicrobial, and tunable mechanical properties. Additionally, insights into the market prospects and trends for soy protein dressings are provided, clarifying the enormous development potential of soy protein as a new type of wound repair material.

Effect of the addition of protein hydrolysates from grape seed meal residue to red wines in warm regions in the stabilization stage

The effect of adding protein hydrolysates from defatted grape seed meals, a residue of the grape pomace industry, on the improvement of color stabilization of Syrah wines in warm climates was evaluated. Factors such as the type of raw material, the hydrolysis time, and the doses of protein hydrolysate were assessed. Hydrolysates were added to the wines at the stabilization stage and scrutinized over five months focusing on the polyphenolic composition, copigmentation and polymerization, as well as color by differential tristimulus colorimetry. The addition of 3 g/L protein hydrolysates from 1-h hydrolysis depicted a color stabilization effect, leading to higher values of chroma (C*ab), phenolic compounds (benzoic acids and flavan-3-ols), and copigmentation, although assuming a slightly more aged-related tonality. These data obtained provide an interesting insight, not reported so far, on the use of this oenological alternative to avoid common color losses of red wines elaborated in warm climate.

Preparation of TiZrHfNbMo refractory high entropy alloy powder via hydrogen plasma-arc melting

Refractory high-entropy alloys (RHEAs) are a new type of metal materials composed of four or more refractory elements. However, the melting point and liquid viscosity coefficient of RHEAs are high, which leads to low fluidity. Therefore, powders of such alloys are difficult to prepare by conventional methods. In this study, a new method called a hydrogen plasma-arc melting has been developed for the preparation of RHEA powders. Results show that the TiZrHfNbMo RHEA powders have single body-centered-cubic (BCC) structures, consisting of a large number of irregularly-shaped powders and small numbers of spherical powders. The average particle size of the powder was 66.97 μm. There is no obvious composition segregation on the surface and inside of the RHEA powders. In addition, this method greatly reduces the oxygen content of the powders.

Highly stable silicon oxycarbide all-solid-state batteries enabled by machined learning accelerated screening of oxides and sulfides electrolytes

Traditional trial–error approach severely limits and restricts rapid development of high-performance anode and electrolytes materials, searching huge parameters space of various anode-solid electrolyte interfaces in an effective and efficient way is the key issue. Here, a novel computational strategy combining machine learning and first-principles is proposed to achieve efficient high-throughput screening of oxides and sulfides electrolytes for highly stable silicon oxycarbide all-solid-state batteries. First-principles calculations demonstrate significant compact of material type and elemental doping on interfacial compatibility between silicon oxycarbide and various electrolytes. By proposing several novel descriptors including interfacial adhesion and formation energies of frozen system with low computation cost, the amounts of demanded trainings data are significantly reduced. Gradient-boosted regression tree model shows low mean absolute errors of 0.09 and high R2 value of 0.99 for the prediction of interface formation energy, demonstrating ultrahigh accuracy and reliability of the algorithm. The present work discovers a series of uninvestigated stable anode-solid electrolytes interfacial couples for further experimental preparation.