Materials For Supercapacitors Research Articles

Activated biomass-derived 3-dimensional porous graphene-like carbon for high-performance energy storage electrode materials

This article reports studies on the fabrication of active material for supercapacitor electrodes, from 3D porous graphene-like carbon (GLC), synthesized by carbonization from coffee waste (CW) and tea waste (TW) at 550 °C, followed by thermochemical activation in KOH at 850 °C in a quartz tubular furnace. The microstructure of coffee and tea waste shows the form of micro- and mesopores during carbonization and further chemical activation forms hierarchically highly porous 3D graphene-like carbon. GLC-CW exhibited a higher specific surface area (SSA) of 3486 m2/g according to the Brunauer-Emmett-Teller (BET) method, compared to GLC-TW, which had an SSA of 2407 m2/g. These results highlight the effectiveness of graphene-like carbon derived from coffee and tea waste, demonstrating its potential as a promising material for high-capacity supercapacitors. The electrochemical characteristics of the assembled supercapacitors using GLC-CW and GLC-TW revealed significantly higher specific capacitance values of 214 F/g and 182 F/g respectively, along with cycling stability of 98 % and 95 % during 5000 cycles of charge and discharge at 2 A/g current density. This approach can produce high-performance electrode materials for supercapacitors at a reasonable cost and with easy scalability.

Molten Salt Assisted Assembly (MASA) of novel mesoporous Ni0.5Mn0.5Co2O4 for high-performance asymmetric supercapacitors

Mesoporous transition metal oxides (TMO) are immensely investigated as electrode materials in supercapacitors. The molten salt assisted self-assembly (MASA) process enables a facile route for the synthesis of the mesoporous TMO. In this study, mesoporous nickel manganese cobaltite (Ni0.5Mn0.5Co2O4) is synthesized for the first time using a MASA process and is evaluated as a novel electrode-active material for asymmetric supercapacitors. The objective of this work is to quantitatively measure the performance improvement in the Ni0.5Mn0.5Co2O4 electrode based on its composition and reveal the improvement mechanism through electrochemical methods. The electrochemical performance of the NiCo2O4 and MnCo2O4 prepared by MASA is also investigated, in order to understand the synergistic effect of Ni and Mn elements in the same cobaltite structure. In line with the data obtained from half cells, a full asymmetric cell is prepared by assembling the appropriate amount of Ni0.5Mn0.5Co2O4 and activated carbon through the charge balance theory. The test results show that the specific capacitance (Cs) values are 2.62F/cm2 (92.1F/g) for mesoporous NiCo2O4, 0.26F/cm2 (9.8F/g) for mesoporous MnCo2O4, and 9.53F/cm2 (338.5F/g) for mesoporous Ni0.5Mn0.5Co2O4 under the test conditions of 5 mA/cm2. The asymmetric supercapacitor assembled with Ni0.5Mn0.5Co2O4 and activated carbon demonstrates a superior energy density of 79.52 Wh.kg−1 at 1 mA/cm2. The findings of the study highlight the importance of substituting the electrode with Ni0.5Mn0.5Co2O4 to enhance the Cs by achieving proper surface properties and electrochemical activity.

Overcoming volumetric capacitance-rate performance tradeoff with 0D/2D conductive carbon nitride/phosphorene heterostructure for flexible supercapacitor

Few-layer black phosphorus (FL-BP) is considered a rising star 2D material for flexible supercapacitors (FSCs) due to its exceptional properties, including mechanical flexibility and high active surface area. However, the disordered deposition of FL-BP nanoflakes often leads to face-to-face restacking, which diminishes the effective active area and ion transport channels. This poses a huge challenge in simultaneously achieving high volumetric capacitance and rate capability. To address this, a 3D porous 0D/2D FL-BP/conductive carbon nitride (FL-BP/c-CN) film has been developed. The introduction of 0D c-CN nanoparticles effectively prevents the restacking of FL-BP nanoflakes and expands the nanofluidic channels, thus facilitating charge transport and ions diffusion. Additionally, the highly conductive c-CN nanoparticles embedded into the FL-BP layers significantly improve overall conductivity. As a result, the FL-BP/c-CN film-based FSC demonstrates a remarkable rate performance, retaining 70% capacitance as the scan rate increases from 10 to 100 mV/s. Moreover, the incorporation of 0D c-CN nanoparticles increases the available space for charge accumulation, yielding a volumetric capacitance of 28.5 F/cm3 at a scan rate of 10 mV/s, which is three times higher than that of a pure FL-BP film electrode (9.2 F/cm3). This work presents an innovative approach for developing high-performance FL-BP-based FSCs.

Facile synthesis and first principles calculations of Li-MoS2/rGO nanocomposite for high-performance supercapacitor applications

Two-dimensional (2D) nanostructured materials such as graphene oxide nanosheets and molybdenum disulfide (MoS2) are potential candidates for electrochemical energy storage applications. The layered structure of MoS2 makes it a promising active electrode material for supercapacitors. Lithium (Li) interacted with MoS2/reduced graphene oxide (Li-MoS2/rGO) nanocomposite has been synthesized in two steps using a sonochemical dispersion method, and a one-pot hydrothermal method resulting in few-layered MoS2/rGO nanosheets of 2D heterointerfaces. The Li-MoS2/rGO nanocomposite exhibits a high specific capacitance of 173.3 F g−1 at a current density of 1 A g−1. Furthermore, an asymmetric supercapacitor device fabricated with Li-MoS2/rGO achieves a good energy density of 10.6 Wh kg−1 at a power density of 686.3 W kg−1 and outstanding cycling stability with 81.2 % capacity retention over 10,000 cycles. The dispersion of 2D-MoS2 in water is due to the strong electrostatic interface. The structural and electronic properties are theoretically calculated for pristine and Li-interacted MoS2/rGO heterostructure using density functional theory. A comparison of the density of states plots of the two heterostructures and the difference charge density plot of Li-MoS2/rGO heterostructure clearly brings out the importance of the presence of Li. A value of 64 μF cm−2 for the quantum capacitance for pristine MoS2/graphene heterostructure increases to a value 99 μF cm−2 corroborating the experimental observations and we assign this change to the transfer of charge from the Li atom to the outer S atoms in the MoS2/graphene heterostructure. This comprehensive approach, combining experimental synthesis with computational modelling, significantly advances the development and optimization of high-performance supercapacitor materials in the energy storage field. The Li-MoS2/rGO nanocomposite has excellent electrochemical specific capacitance and long-term cyclic stability and has been effectively used for supercapacitor applications with high electrochemical performance.

Composition-optimized NiGa-LDH on MOF-derived and cobalt-nanoparticles-embedded carbon flakes for enhanced potassium-ion storage

Layered double hydroxides (LDHs), renowned for their distinct nanostructures, efficient ion channels, and high specific capacitance, are promising electrode materials for supercapacitors (SCs). However, commercial applications remain limited due to constraints in the rate capabilities and cycling. The synergistic effects of the composites can be leveraged by pairing LDHs with carbon materials to enhance the conductivity for better SC characteristics. Herein, flaky Zeolitic Imidazolate Framework(ZIF)-67 is deposited on carbon cloth and calcined to produce the MOF-derived composite of carbon nanosheet-embedded nano-cobalt particles (CPEC) on the surface of the carbon cloth. Afterward, NiGa-LDH with a controllable Ni to Ga ratio is synthesized on the CPEC to form a flower-like hierarchical nanostructure NiGa-LDH/CPEC@CC. Co nanoparticles act as nucleation sites for cohesive formation within the carbon cloth framework. Ni2Ga1-LDH/CPEC@CC has the best properties, such as a specific capacitance of 729.6F g−1 at 1 mA cm−2 and 97.3 % capacitance retention at 2 mA cm−2. The asymmetric supercapacitor (ASC) consisting of Ni2Ga1-LDH/CPEC@CC//AC has an excellent energy density of 83.96 Wh kg−1 with a power density of 80 W kg−1. Density-functional theory (DFT) calculations of Ni2Ga1-LDH/CPEC@CC affirm a potassium ion adsorption energy of −2.127 eV and density of state (DOS) near the Fermi level. The study imparts theoretical and technical knowledge about the design of complex nanostructures from MOF precursors.

Functional metal-organic frameworks derived electrode materials for electrochemical energy storage: a review.

Pristine metal-organic frameworks (MOFs) are built through self-assembly of electron rich organic linkers and electron deficient metal nodes via coordinate bond. Due to the unique properties of MOFs like highly tunable frameworks, huge specific surface areas, flexible chemical composition, flexible structures and a large volume of pores, they are being used to design the electrode materials for electrochemical energy storage devices. As per the literature, MOFs (including manganese, nickel, copper, and cobalt-based zeolitic imidazolate frameworks (ZIFs), University of Oslo (UiO) MOFs, Hong Kong University of Science and Technology (HKUST) MOFs and isoreticular MOFs (IRMOFs)) have attracted much attention in the field of supercapacitors (SCs)/batteries. According to their dimensionality such as 1D, 2D and 3D, pristine MOFs are mainly used as SC materials. Highly porous materials and their composites are capable for intercalation of metal ions (Na+/Li+). Moreover, the supramolecular features (π⋯π, C-H⋯π, hydrogen bond interactions) of redox stable MOFs provide better insight for electrochemical stability. So, this review provides an in-depth analysis of pure MOFs and MOF derived composites (MOF composites and MOF derived porous carbon) as electrode materials and also discusses their metal ion charge storage mechanism. Finally, we provide our perspectives on the current issues and future opportunities for supercapacitor materials.

Probing structural and electrochemical properties of a 2D CoMoO4@hBN nanocomposite as pseudocapacitive electrode for high-performance supercapacitors

The effectiveness of energy storage is largely determined by the electrode material's performance in critical areas. Enhancements in ion transport, cyclic stability, rate capability, and specific capacitance directly boost the supercapacitors' overall performance and broaden their application potential. This study aims to enhance these properties by incorporating hexagonal boron nitride (hBN) into cobalt molybdate (CoMoO4) material in a 1:1 stoichiometric ratio. The CoMoO₄@hBN nanocomposite was synthesized using a hydrothermal method followed by ball milling. The X-ray diffraction (XRD) analysis confirmed the formation of a single-phase CoMoO4@hBN composite, with a significant increase in crystallite size from 18.21 nm in pure CoMoO₄ to 25.6 nm, along with a slight shift in diffraction peaks, indicating enhanced crystallinity and structural defects due to the substitution of oxygen with boron atoms. Raman spectroscopy revealed that the composite retains the characteristic peaks of both CoMoO₄ and hBN, with stable sharp peaks at 936 cm−1 (Mo=O bond) and 1367 cm−1 (E2g peak of hBN) even after 20 depth measurements, confirming successful conjugation and consistent vibrational properties. The X-ray photoelectron spectroscopy (XPS) showed a slight shift in Co 2p and Mo 3d binding energies to higher values, suggesting improved electronic interactions between CoMoO4 and hBN, which could enhance the composite's conductivity. The electrochemical analysis demonstrated that incorporating h-BN significantly boosts the electrode's performance compared to pristine CoMoO4, with about 37 % increase in specific capacitance at 1 A g−1, reduced charge transfer resistance (0.11 Ω), and superior cyclic stability with 96 % capacitance retention after 5000 cycles. These findings indicate that hBN enhances both the electrical conductivity and structural integrity of CoMoO4, positioning the CoMoO4@hBN composite as a promising material for high-performance supercapacitors.

Synthesis of Porous Carbons from Candlenut Shells Using Various Types of Activators for Environmentally Friendly Supercapacitors

Porous carbon is one of the promising electrode materials for supercapacitors due to its unique and engineerable microstructural properties. The study of the synthesis of porous carbon from waste biomass is very important due to the abundance of natural resources, low cost production and contribute to solving environmental problems. In this study, porous carbons derived from candlnut shell with various type of activator was studied the chemical structural, morphological and electrochemical properties then evaluated as electrodes for supercapacitor. We have been successfully synthesized of porous carbon from candlenut shells using three steps of the process, i.e.: carboni-zation, activation and calcination. Carbonization was carried out at 700°C in a furnace using a closed crucible to minimize the oxygen. The chemical activation conducted using three types of activators, i.e. ZnCl2, H3PO4 and KOH then calcination process by heated at 800°C for 1 h under Ar flow. The results of the Fourier-transform infrared (FTIR) analysis show that the carbonization process increases the content of aromatic C=C functional groups and reduce the OH, C-H, C-O and C=O functional groups. The carbonization process has also increased the electrical conductivity of the sample around 0.8525 S/m. The results of Scanning Electron Microscope (SEM) images can be observed that the activation process of carbon has formed which was indicated by the appearance of many pores on the surface area of carbon. N2 adsorption/desorption isotherms (Brunauer–Emmett–Teller (BET)) characterization was indicated that the porous carbon is dominated by mesoporous with a pore size around 2-50 nm. BET characterization also can be determined the surface area of porous carbon around 477 m2/g for ZnCl2, 636 m2/g for H3PO4, and 681 m2/g for KOH. This synthesized materials are further employed in a symmetric supercapacitor using simple glass cell. The best performance of supercapacitor achieved by KOH porous carbons with 16.30 F/g of specific capacitance, 2.26 Wh/kg of energy density and 1038 W/kg of power density.

Constructing Co3O4 Nanowire@NiCo2O4 Nanosheet Hierarchical Array as Electrode Material for High-Performance Supercapacitor

The Co3O4 nanowire@NiCo2O4 nanosheet hierarchical array was constructed on Ni foam using hydrothermal and annealing approaches in turn, from which a NiCo2O4 nanosheet could self-assemble on the Co3O4 nanowire. The structure and morphology of the Co3O4 nanowire@NiCo2O4 nanosheet hierarchical array were characterized via XRD, EDS, SEM, and FESEM, respectively. The electrochemical performance of the composite array was measured via a cyclic voltammetry curve, galvanostatic current charge–discharge, charge–discharge cycle, and electrochemical impedance and then compared with the Co3O4 nanowire. The results show that the Co3O4 nanowire@NiCo2O4 nanosheet hierarchical array could reach a high value of 2034 F g−1 at a current density of 2.5 A g−1. After 5000 galvanostatic charge–discharge cycles, the specific capacitance of the Co3O4 nanowire@NiCo2O4 nanosheet hierarchical array could still maintain 94.7% of the original value. Therefore, the Co3O4 nanowire@NiCo2O4 nanosheet hierarchical array would be a desirable electrode material for a high-performance supercapacitor.

Anode Glow Discharge Electrolysis Synthesis of Flower-Like α-MnO2 Nanospheres: Structure, Formation Mechanism, and Supercapacitor Performance.

A novel green synthesis strategy-anode glow discharge electrolysis (AGDE) was employed for one-step preparation of α-MnO2 in 2 g L-1 KMnO4 solution, in which Pt needle and carbon rod were regarded as anode and cathode, respectively. The optimal preparation condition is 400 V for 60 min and the power consumption is below 45 W. The XRD, Raman spectra, XPS and EPR proved that α-MnO2 with structural defects (oxygen vacancies) is obtained. SEM and TEM revealed that α-MnO2 shows a flower-like nanospheres with a diameter of 165 nm, which is assembled by many nanosheets. A possible formation mechanism is that the MnO2 is generated via the reduction of MnO4 - by H⋅ and eaq - in plasma-liquid interface. Electrochemical test found that MnO2 nanospheres exhibit a specific capacitance of 365 F g-1 at 1 A g-1, and capacity retention of 79.8 % after 10,000 cycles at 5 A g-1. The assembled asymmetric supercapacitor shows the maximum energy density of 23.1 Wh kg-1 at power density of 1.89 kW kg-1. In brief, AGDE is a simple, facile and green technique for the synthesis of α-MnO2 without adding extra chemicals, and prepared α-MnO2 can be considered as an excellent candidate of electrode materials for supercapacitor.

Schiff base polymer doped with MWCNTs as electrode material for supercapacitors

Schiff base polymer doped with MWCNTs as electrode material for supercapacitors

Hydrothermal synthesis of MoS2 nanoparticle as an electroactive material for supercapacitor

Hydrothermal synthesis of MoS2 nanoparticle as an electroactive material for supercapacitor

Redox-mediated synthesis of Cu2O/CuO/Mn3O4/C quaternary nanocomposites as an efficient electrode material for oxygen reduction reaction and supercapacitor application

Earth-abundant transition metal oxides (TMOs) hold significant promise as electroactive materials in various electrochemical energy conversion and storage applications, offering economic and environmental advantages over their less abundant counterparts. In this work, a simple and cost-effective redox-mediated reaction strategy under hydrothermal conditions has been adopted to synthesize the quaternary nanocomposites Cu2O/CuO/Mn3O4/C with variable amounts of carbon. The synthesized nanocomposites have been characterized using various analysis techniques, including powder X-ray diffraction (PXRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and Brunauer–Emmett–Teller (BET). The synthesized COM5 nanocomposite (Cu2O/CuO/Mn3O4/C-50), when used as an electrocatalyst for the oxygen reduction reaction (ORR), demonstrates a good limiting current density (JL), half-wave potential (E1/2), and onset potential (Eonset) of −5.50 mA/cm2, 0.75 V, and 0.95 V, respectively, as per the polarization curve. The COM5 nanocomposite exhibits a four-electron transfer mechanism, calculated using the Koutecky-Levich (K-L) equation. In an O2-saturated 0.1M KOH solution, the COM5 nanocomposite has shown a superior relative current durability of 84.46% over 14,000 s compared to the commercially available 10 wt% Pt/C, indicating its potential application in the ORR. However, for supercapacitor applications, the COM3 nanocomposite (Cu2O/CuO/Mn3O4/C-20) as active electrode material in galvanic charge-discharge (GCD) study shows superior performance (201 F/g at 1 A/g) compared to the COM2 nanocomposite (117 F/g at 1 A/g) in neutral aqueous electrolyte, possibly due to the lower charge transfer resistance (Rct) of 24.04 Ω compared to COM2 (34.63 Ω). In two-electrode studies, the COM3 nanocomposite exhibits a good energy density of 24.19 Wh/kg at 1 A/g and a 4.7 kW/kg power density at 5 A/g. Additionally, the COM3 nanocomposite shows excellent long-term durability (74% capacitance retention) at the current density of 5 A/g for 8000 cycles. The electrochemical findings indicate that the COM3 nanocomposite stands out as a superior electrode material for supercapacitors, while the COM5 nanocomposite proves to be an effective electrocatalyst for the oxygen reduction reaction.

A review on progress and prospects of diatomaceous earth as a bio-template material for electrochemical energy storage: synthesis, characterization, and applications

AbstractThis comprehensive review explores the remarkable progress and prospects of diatomaceous earth (DE) as a bio-template material for synthesizing electrode materials tailored explicitly for supercapacitor and battery applications. The unique structures within DE, including its mesoporous nature and high surface area, have positioned it as a pivotal material in energy storage. The mesoporous framework of DE, often defined by pores with diameters between 2 and 50 nm, provides a substantial surface area, a fundamental element for charge storage, and transfer in electrochemical energy conversion and storage. Its bio-templating capabilities have ushered in the creation of highly efficient electrode materials. Moreover, the role of DE in enhancing ion accessibility has made it an excellent choice for high-power applications. As we gaze toward the future, the prospects of DE as a bio-template material for supercapacitor and battery electrode material appear exceptionally promising. Customized material synthesis, scalability challenges, multidisciplinary collaborations, and sustainable initiatives are emerging as key areas of interest. The natural abundance and eco-friendly attributes of DE align with the growing emphasis on sustainability in energy solutions, and its contribution to electrode material synthesis for supercapacitors and batteries presents an exciting avenue to evolve energy storage technologies. Its intricate structures and bio-templating capabilities offer a compelling path for advancing sustainable, high-performance energy storage solutions, marking a significant step toward a greener and more efficient future. Graphical Abstract

Molecular-Level Pore Tuning in 2D Conductive Metal-Organic Frameworks for Advanced Supercapacitor Performance.

Two-dimensional (2D) electrically conductive metal-organic frameworks (MOFs) have emerged as viable candidates for active electrode materials in supercapacitors due to their high electrical conductivity, high specific surface area, and intrinsic redox-active sites. Despite their promising electrochemical performance, their pseudocapacitive behavior via fast and reversible charge transfer reactions remains yet to be fully exploited. Here, we investigate the electrochemical energy storage mechanism of Cu3(HHTATP)2 (HHTATP = 2,3,6,7,10,11-hexahydroxy-1,5,9-triaminotriphenylene), a 2D conductive MOF featuring characteristic redox-active pendant aromatic amines. Cu3(HHTATP)2 exhibited pseudocapacitive charge storage with an average gravimetric capacitance of 340 ± 15 F g-1 at a discharge rate of 0.2 A g-1 and maintained a capacitance retention over 90% after 7000 galvanostatic cycles at 5 A g-1. The polar pendant amines not only enhanced capacitance via additional amine/imine redox activity but also reduced interfacial charge transfer resistance through modified electrode-electrolyte interactions. These results highlight the potential of molecular-level pore environment tuning as a strategic approach in materials design for energy storage applications.

Graphene wrapped porous polyaniline/manganese oxide nanocomposites with enhanced structural stability and conductivity for high‐performance symmetric supercapacitor

AbstractManganese oxides have emerged as promising electrode materials for supercapacitors. Despite extensive efforts to improve their conductivity and structural stability through various manganese oxide/conductor nanocomposites, achieving efficient and reliable energy storage electrode materials has remained challenging. In this study, we propose a meticulous “dual enhancement” strategy, where three‐dimensional (3D) nanostructured polyaniline/manganese oxide composites (PM) are synthesized via an in situ method and further integrated with graphene wrapping to form polyaniline/manganese oxide/graphene nanocomposites (PMG). Electrochemical characterization reveals that PMG exhibits a remarkable specific capacitance of up to 403 F g−1 (at 1 A g−1), with a favorable capacitance retention of 80.2% after 5000 cycles, along with a wide potential window. This enhancement is attributed to the synergistic effects of polyaniline, which provides a supportive framework and electron transport pathways, and graphene, which offers external protection and enhances conductivity pathways. Assembled symmetrical supercapacitors demonstrate outstanding energy density (32.7–23.3 Wh kg−1) and power density (720–4500 W kg−1) at a high operating voltage of 1.8 V, surpassing the performance of many reported high‐performance supercapacitors. This study provides valuable insights for advancing manganese oxide electrode materials and is expected to catalyze their widespread adoption in energy storage applications.Highlights “Dual enhancement” is implemented by PANI supporting and rGO wrapping. The conductivity and structural stability of composite electrode is greatly enhanced. Improved capacitance (403 F g−1, 1 A g−1) and cycling stability (80.2%) is achieved. The symmetrical supercapacitor has high voltage and energy density (32.7 Wh kg−1).

Tailoring MnO2 nanowire defects with K-doping for enhanced electrochemical energy storage in aqueous supercapacitors

The fabrication of supercapacitors with outstanding performance is presented with a distinct defect-rich nanostructures. A one-pot, energy-efficient method for synthesizing defective manganese dioxide nanowires doped with potassium (K0.35MnO2) was developed. The introduction of potassium ions at 35 % birnessite resulted in a significant increase in lattice defects and an improvement in conductivity. Addition of KOH induces a phase transition from α-MnO2 to δ-MnO2. These imperfections result in a greater quantity of active sites, which are crucial for the process of energy storage. The K0.35MnO2 structure demonstrates a 405F/g increased capacity at a current density of 1 A/g. The asymmetric supercapacitor (K0.35MnO2/AC) that was manufactured exhibits a capacitance of 106.4F/g when operating at 1 A/g, while maintaining a maximum energy density of 71.5 Wh kg−1 and a power density of 672 W kg−1. Furthermore, 92.7 % of the initial capacitance of the device is retained even after 8,000 cycles at 20 A/g. This study presents novel insights into the production of defective materials for energy storage applications through the utilization of a one-pot process as opposed to the multi-step method. In order to produce high-performance supercapacitors for practical applications, the results indicate that defect engineering is a crucial factor.

Upcycling Waste Polyethylene Terephthalate to Produce Nitrogen-Doped Porous Carbon for Enhanced Capacitive Deionization

Porous carbon with a high surface area and controllable pore size is needed for energy storage. It is still a significant challenge to produce porous carbon in an economical way. Nitrogen-doped porous carbon (N-PC) was prepared through carbonization of a mixture of waste PET-derived metal–organic frameworks (MOFs) and ammonium. The obtained N-PC exhibits a large surface area and controlled pore size. When utilized as an electrode material for supercapacitors, the N-PC exhibits a specific capacitance of 224 F g−1, significantly surpassing that of commercial activated carbon (AC), which has a capacitance of 111 F g−1. In the subsequent capacitive deionization (CDI) tests, the N-PC demonstrated a maximum salt adsorption capacity of 19.9 mg g−1 at 1.2 V in a NaCl electrolyte (0.5 g L−1), and the salt adsorption capacity increased to 24.7 mg g−1 at 1.4 V. The N-PC electrode also exhibited superior regeneration. The present work not only presents a potential approach to develop cost-effective electrodes for seawater purification but also paves the way for recycling of waste plastics into high value-added products.

V2O5-MnO2 nanocomposites as an efficient electrode material for high-performance aqueous supercapacitors

Redox-active supercapacitors are very interesting due to their high energy density (>25 Wh kg−1 at device level) and redox charge storage mechanism. In this work, V2O5-MnO2 nanocomposites are synthesized by a scalable hydrothermal approach. MnO2 in V2O5 provides better structural stability with reasonable electrochemical performance, in which V2O5 enhances the cyclic stability and rate capabilities. The V2O5-MnO2 -based electrodes deliver a specific capacitance of 266 F g−1 at 0.5 A g−1 and are stable up to 6500 cycles with 97 % capacitance retention at 5 A g−1. The kinetic study depicts that composite electrodes have a 64 % diffusive and 36 % capacitive charge storage contribution to the overall charge storage at 1 mV s−1. In symmetric full cells, the composite materials show a wide active potential window of 2.5 V and retain 83 % capacitance after 10000 continuous GCD cycles at an applied current density of 2 A g−1. The promising charge storage performance is due to a suitable conducting matrix and the effective coating of MnO2 nanoparticles over the unique V2O5 niddle shape (two-dimensional) micro-rods.

Acid-treated waste sisal fiber derived activated carbon as efficient electrode material for solid-state supercapacitor

Activated Carbon (AC), obtained from biomass is highly adaptable and valued for its versatile benefits including high surface area, conductivity, chemical inertness, etc. in various applications. It is also used as an electrode in supercapacitors for applications requiring a high-power supply. Sisal fiber, derived from the Agave sisalana plant, has several advantages, including its fibrous and porous framework, that make it suitable for conversion into activated carbon for energy storage applications in the context of sustainability and reduced environmental impact. In this study, we have prepared H2SO4 treated KOH activated carbon from residual Sisal fiber (SFH2AC) which is then utilized as an electrode material for supercapacitors. SFH2AC exhibits hierarchical and structure-based porosity with a large specific surface area (SA) of 1185 m2/g and shows the maximum specific capacitance (Cs) of 340 F/g @ 0.5 A/g in 6 M KOH electrolyte. In KOH electrolyte, strong cycling retention (during the length of 9000 GCD cycles) is attained as; 98 % up to the first 3000 cycles at 10 A/g, 93 % up to next 3000 cycles at 20 A/g, and 90 % up to the last 3000 cycles at 30 A/g. Furthermore, the SFH2AC//SFH2AC(Gel) device was built by using SFH2AC as electrodes with PVA/KOH gel as an electrolyte in order to assess the supercapacitor performance in real time. The device has a specific power density of 7500 W/kg and a maximum energy density of 12 W h/kg. The device reveals an exceptional 97 % cycling stability, maintaining up to 9000 repeated GCD cycles at an increased current density (CD) of 30 A/g.