Dynamic Modulus Master Curves Research Articles

Study on the characterization method of dynamic modulus for asphalt mixture under multi-factor coupling conditions

In the actual service process of asphalt pavement, the dynamic response of the pavement structure layer is induced by vehicle loads. The dynamic modulus is a crucial parameter for analyzing the mechanical response of asphalt pavement. Due to significant influences from temperature and loading frequency on test measurements, along with its time-temperature equivalence, it becomes imperative to investigate the behavior of dynamic modulus under different temperature frequencies. Furthermore, laboratory loading modes also exert substantial effects on dynamic modulus. Employing different loading modes during measurement often leads to significantly varied stress states in specimens, yielding distinct values for dynamic modulus. Therefore, this study conducts dynamic modulus tests using direct tension, uniaxial compression, and indirect tension under five test temperatures and six loading frequencies while examining its variations under different stress states and temperature frequencies. The corresponding master curves and prediction models of dynamic modulus are derived, providing a valuable reference for predicting the dynamic modulus under wide-area test conditions. Through comparative analysis of dynamic modulus values at different stress levels, the stress level is incorporated into the master curve to establish corresponding master curves of dynamic modulus. By applying relevant theories and research on time-temperature equivalence, we obtained dynamic modulus master curves for three loading modes by fitting and analyzing dynamic modulus test data at various temperatures and loading frequencies. Combining the Sigmoid model and Williams-Landel-Ferry(WLF) equation, we derived prediction models for dynamic modulus under three loading modes. Comparative analysis of dynamic modulus values under these three loading modes allowed us to establish transformation equations for the prediction models in different loading scenarios. Finally, representative dynamic modulus values for permanent deformation in typical pavement structure layers were predicted based on laboratory test results and the derived models. The research findings presented in this paper have significant implications in eliminating the influence of loading modes on dynamic modulus predictions, establishing a unified prediction model, and providing essential parameters for predicting permanent deformation and fatigue life equivalent temperature.

An alternative approach for characterization of the linear viscoelastic behavior of asphalt binders

This study aimed to develop an alternative approach to characterise the linear viscoelastic behaviour of asphalt binders. A rheogram model was firstly proposed based on the Carreau–Yasuda model; its accuracy was substantiated by high R 2 values. The dynamic shear modulus master curve model was then obtained using the relationship between the magnitude of complex viscosity and dynamic shear modulus and the two definitions of the time-temperature shift factor. Afterwards, the phase angle master curve model was derived according to the approximate Kramers–Kronig relation. The proposed approach was demonstrated to be capable of accurately characterising the linear viscoelastic behaviour of selected asphalt binders. In addition, the predicted zero shear viscosity (ZSV) could be potentially employed to evaluate the asphalt binder rutting resistance. Compared with the widely-used Christensen-Anderson-Marasteanu (CAM) model, the developed master curves models were better at constructing the phase angle master curves of selected asphalt binders.

Rheological and Aging Characteristics of Polymer-Modified Asphalt with the Addition of Sulfur

Crosslinking agents, notably sulfur, are used in asphalt binder modification to facilitate chemical bonding between polymer chains and the asphalt binder. Despite some prior research indicating the benefits of sulfur crosslinking in enhancing polymer-modified asphalt’s (PMA) stability, there is a lack of comprehensive understanding regarding its impact on rheological properties and its anti-aging potential. This study addresses these gaps by thoroughly investigating the effects of varying the sulfur content (ranging from 0.03% to 0.5% by total weight of binder) on PMA’s rheological properties. The research assesses the effectiveness of sulfur in enhancing PMA’s resistance to aging using various methods, including the Glover-Rowe parameter, FTIR analysis, and the examination of the dynamic modulus and phase angle master curves. The results indicated that the addition of sulfur, particularly up to 0.3%, bumps the high-temperature performance grade by one level, and significantly improves elasticity, allowing the PMA to support heavier traffic without experiencing rutting, all while maintaining resistance to low-temperature cracking. Furthermore, PMA with sulfur demonstrated an increase in resistance to aging, reducing the aging potential by approximately 15% with the best sulfur formulation. This enhanced durability can reduce the frequency of maintenance activities, leading to cost savings, reduced roadwork emissions, and prolonged pavement life.

An Approach for Adjusting the Laboratory-Determined Dynamic Modulus Master Curve of Asphalt Layers Based on Falling Weight Deflectometer Measurements

Structural assessment is critical for designing asphalt pavement overlays, estimating the remaining life of pavements, and selecting an appropriate rehabilitation strategy for existing pavements. The falling weight deflectometer (FWD) serves as the primary nondestructive test used for evaluating the in situ properties and structural capacity of asphalt pavements. The current procedure involves analyzing the FWD response and estimating layer moduli by assuming an elastic response. However, the response of asphalt layers is viscoelastic (i.e., temperature- and frequency-dependent). This study proposes an approach that combines FWD data with laboratory measurements of the dynamic moduli of field cores to determine the in situ viscoelastic properties of asphalt layers. This approach is implemented by analyzing FWD data from four pavement sections in Qatar. Furthermore, the paper includes a comparative analysis of the response of pavement sections in which the asphalt layers are modeled using dynamic modulus master curves obtained from laboratory tests and those obtained using the approach presented in this study. It was found that using the laboratory-based master curves overestimated pavement performance (i.e., underestimated pavement distresses). It is recommended to use the dynamic moduli from the method presented in this paper for a more accurate estimation of pavement response and performance.

Experimental Study on the Dynamic Modulus of an Asphalt Roadbed Grouting Mixture under the Influence of Complex and Multiple Factors

After long-term service, the ground will experience settlement and the stability of the roadbed will be lost. In order to effectively reinforce the roadbed, an asphalt roadbed grouting mixture has been applied to the filling of the roadbed. The rotary compaction method was used to prepare different gradation types of lime composite-modified oil sludge pyrolysis residue asphalt, mixtures Sup13, Sup19, and Sup25. This article takes the dynamic modulus of an asphalt roadbed grouting mixture as the mechanical index, and the uniaxial compression dynamic modulus test is carried out on three kinds of rotary compaction asphalt mixtures, Sup13, Sup19, and Sup25. The dynamic modulus master curves of different gradation composite-modified oil sludge pyrolysis residue asphalt mixtures are fitted to study the dynamic modulus of asphalt mixtures under different nominal maximum particle sizes, loading frequencies, and temperatures. The results show that (1) The dynamic modulus of different gradation composite-modified oil sludge pyrolysis residue asphalt mixtures increases with the decrease in temperature and the increase in frequency; (2) when other conditions are the same, the compound-modified asphalt mixture’s dynamic modulus decreases significantly under low-frequency and high-temperature conditions; (3) in the range of 4.4–37.8 °C and medium loading frequency, the dynamic modulus of the compound-modified asphalt mixture is more affected by temperature and loading frequency; (4) in the low-temperature and high-frequency range, the compound-modified asphalt mixture with a larger nominal maximum particle size has a higher dynamic modulus, and the asphalt mixture with better stability of skeleton structure has a higher dynamic modulus. The research results of this article will provide scientific guidance for the study of the mechanical properties of asphalt roadbed grouting mixtures.

Study on the Construction of Dynamic Modulus Master Curve of Polyurethane Mixture with Dense Gradation

The PU mixture considered here is a new kind of pavement material with excellent road performance, which lacks study into its dynamic mechanical and viscoelastic properties. In this study, the dynamic modulus of the polyurethane (PU) mixture was fitted by using five master curve models, five shift factor equations, and four error minimization methods. According to test results, the log–log plot form was able to more effectively display the differences between master curves. The solver method, the sum of square error minimization (≤0.02), proved to be more appropriate and accurate with higher fitting parameter results. The line of equality statistic and Pearson linear correlation analysis results demonstrated that WLF and Kaelble equations were appropriate for five master curve models with trend line R2 values higher than 0.98. The GLS and SCM model with the WLF equation had the most accurate master curve fitting results. The dynamic modulus master curve shape of the PU mixture did not follow the traditional smooth “S” shape and did not show the ultimate dynamic modulus at extreme frequency. The viscoelasticity of the PU mixture is quite different from that of the asphalt mixture. This study recommended the most accurate error minimization method, the master curve model, and shift factor equations for characterizing the dynamic properties of the PU mixture.

A Comprehensive Analysis of Fatigue and Healing Capacity of Sasobit Polymer-Modified Asphalt from Two Perspectives: Binder and FAM

Wax-based Sasobit synthetic hard wax can be designed for producing asphalt with less energy consumption and lower carbon emissions in the pavement industry. This study investigated the effectiveness of Sasobit synthetic hard wax on microscopic properties, fatigue-fracture behavior, and healing potential of polymer-modified asphalt (PMA) from two perspectives: asphalt binder and fine aggregate matrix (FAM). First, microscopic morphology, dispersion mechanism, and thermal stability of styrene-butadiene-styrene (SBS)– and crumb rubber (CR)–modified asphalt binders under the influence of Sasobit synthetic hard wax were characterized. Second, linear viscoelastic properties and evolution law of fatigue life of Sasobit synthetic hard wax/polymer-modified asphalt binders and FAM with and without healing interval were assessed under the framework of the simplified viscoelastic continuum damage (S-VECD) model. Third, the correlation between properties of the modified asphalt binder and FAM was statistically analyzed by radar chart. Thermodynamic analysis indicated that Sasobit synthetic hard wax enhanced the thermal stability of PMA but slightly reduced the low-temperature performance. Morphological observations showed that Sasobit synthetic hard wax had limited effectiveness on the dispersion of the polymer particles in PMA. Dynamic modulus master curves and fatigue and healing tests demonstrated that Sasobit synthetic hard wax contributes to the stiffness, fatigue resistance, and self-healing capability of the asphalt binder and mixture. Finally, statistical analysis revealed that the asphalt binder performance lacked a close correlation with the FAM owing to the complex composition system.

A time-temperature-ageing shift model for bitumen and asphalt mixtures based on free volume theory

ABSTRACT This paper aims to develop a general form of the time-temperature-ageing shift model for bituminous materials based on free volume theory and validate its application in the Finite Element (FE) modelling for predicting aged asphalt mixtures’ mechanical responses. The frequency sweep, dynamic modulus, and Fourier Transform Infrared Spectroscopy (FTIR) tests were used to validate the proposed time-temperature-ageing shift model. A generalised Maxwell model incorporating the proposed shift model of asphalt mixtures was used to predict the mechanical responses of aged asphalt mixtures using FE modelling, verified via laboratory cyclic load tests. Results indicate that the time-temperature-ageing shift function can model the complex shear modulus and dynamic modulus master curves of bituminous materials, addressing the modulus dependency of temperature and ageing. Temperature dominates the modulus change of bituminous materials in the ageing process. The coefficients of the time-temperature-ageing shift model have clear physical meanings and can potentially quantify the effects of asphalt mixtures’ air voids on their temperature and ageing susceptibilities. The time-temperature-ageing shift model can be incorporated into the constitutive relations of the FE model to effectively couple and efficiently predict the effects of temperature and ageing on the mechanical responses of aged asphalt mixtures.

The Stiffness Behavior of Asphalt Mixtures with Different Compactness under Variable Confinement.

The dynamic modulus is a key property determining the short- and long-term performance of asphalt pavement, and its strong dependence on confining pressure and material density (mixture compactness) has been clearly indicated in the literature. It is always challenging to reproduce three-dimensional in situ stress conditions in the laboratory. To alleviate this difficulty, in this study, a convenient experimental setup was developed, in which the lateral confinement was made present and variable as a concomitant reaction of the surrounding materials to the vertical loading. Three dense-graded mixtures were prepared to a set of four different densities and then subjected to the confined dynamic modulus test. The results indicated a significant dependence of the confined modulus on the three factors of temperature, frequency, and compactness and that the mixture with coarser gradation demonstrated a less sensitivity to these parameters. A mathematical model was developed for the dynamic modulus master curve unifying these factors by means of horizontal shifting due to the time-temperature superposition principle (validated against the variable confinement at different compactness) and the vertical shift factor as a function of reduced frequency and compactness. The adequacy of the model was demonstrated using the experimental data, and its potential application in field pavement compaction was discussed.

Structural optimization of steel bridge deck pavement based on mixture performance and mechanical simulation

The upper layer of modified SMA mixture (SMAM) and the lower layer of epoxy asphalt mixture (EAM) is a steel bridge deck pavement (SBDP) structure with application potential, but there is a lack of systematic research on it. In this study, the pavement material and structure of SMAM + EAM were optimized using mixture performance tests and finite element analysis, which provided guidance to facilitate its promotion and application. Firstly, the pavement performance and dynamic properties of SMAMs and EAMs prepared with different binders were compared to preferably select the appropriate SBDP material. Secondly, the dynamic modulus master curves of the mixtures were established to provide material parameters for pavement structure design. Finally, the FEA method was applied to comparatively analyze the dynamic mechanical response of the pavement structure for different structures, thickness combinations, and temperatures to optimize the SBDP structure purposefully. The results demonstrated that EAM had better high-temperature rutting resistance than SMAM, while SMAM had superior moisture damage and skid resistance. The modifier contents in the asphalt binder used for SMAM and EAM were recommended to be 12 wt% and 40 wt%, respectively. From the FEA results, the SMAM + EAM structure met the performance requirements of SBDP. Compared with double-layered EAM, the deformation resistance of the SMAM + EAM structure was reduced, but it was beneficial to avoid the occurrence of crack defects and interlayer shear damage. Furthermore, the recommended pavement thickness combination was 4.5 + 3.5 cm.

Use of the Modified Ramberg-Osgood Material Model to Predict Dynamic Modulus Master Curves of Asphalt Mixtures.

Dynamic modulus master curves are usually constructed by using sigmoid functions, but the coefficients of these functions are not independent of each other. For this reason, it is not possible to clearly identify their physical mean. Another way of describing the dynamic modulus master curves is to choose the Ramberg-Osgood (RAMBO) material model, which is also well-suited for modelling the cyclic behaviour of soils. The Ramberg-Osgood model coefficients are completely independent of each other, so the evaluation of the fitted curve is simple and straightforward. This paper deals with the application of the Ramberg-Osgood material model compared to the usual techniques for constructing a master curve, determining the accuracy in describing the material behaviour of asphalt mixtures, and seeking any surplus information that cannot be derived by traditional techniques. Because the dynamic modulus and phase angle master curves are strictly related, in the present study, the asymmetric bell-shaped frequency curve of Toranzos was used to describe the phase angle for four types of asphalt mixtures (RmB, PmB, RA, and NB). The results show that the RAMBO model is a good alternative to the sigmoid function in describing the master curve of the dynamic modulus. We successfully used the Toranzos asymmetric bell-shaped frequency curve to describe the phase angle master curve. We also found a promising relationship between the independent RAMBO model parameters and the physical properties of the investigated binders, but this requires further research.

Comparative study of indirect tensile test and uniaxial compression test on asphalt mixtures: Dynamic modulus and stress-strain state

Dynamic modulus is an essential parameter for the performance characterisation of asphalt materials for performance prediction and pavement design. The Indirect Tensile (IDT) test and the Uniaxial Compression (UC) test are both well-known experiments performed in the laboratory to characterise the dynamic modulus of asphalt mixtures over a range of temperatures and loading frequencies. A considerable amount of research has investigated the difference between two test modes, while few studies analysed the fundamental difference in stress–strain distributions for the two test setups. This work aims at comparing the effect of the two test methods on dynamic modulus of asphalt mixtures, as well as stress–strain state. For these purposes, two types of mixtures commonly employed to build road surface layers, namely Asphalt Concrete (AC) and Stone Mastic Asphalt (SMA), were created and tested. The specimens were prepared with a gyratory compactor. The master curves of dynamic modulus and the stress–strain states obtained from the two testing procedures were compared. The dynamic modulus and phase angle results are almost identical for medium frequency and temperature, whereas the results exhibit significant discrepancies for lower and higher frequency values. AC 11 and SMA 11 mixtures show differences in comparison between the two tests. Moreover, the strains measured by the IDT test are variable and the strains obtained from the UC test stabilise around 40 με. Similarly, both tests have poor strain control at 40 °C. The values of normalised stresses measured by the IDT test are approximately 3.26 and 2.34 times greater than the ones measured by the UC test for AC 11 and SMA 11 mixtures, respectively. In general, the results of the mechanical characterisation of the asphalt mixtures conducted using both tests are similar. The IDT test has the advantage of sample size for sample preparation methods in both laboratory and field, and the UC test has a better deformation control at low and medium temperatures.

Strain softening of natural rubber composites filled with carbon black and aramid fiber

Engineered rubber vulcanizates may contain a low content of short fibers and a high content of nanoparticles while the effects of the different fillers on the softening behavior are not yet explored. Herein, influences of carbon black (CB) and short aramid fiber (AF) on the Payne and Mullins effects of natural rubber composites are investigated for the first time by creating master curves of dynamic modulus or dissipation energy with respect to the straining responses of the matrix. It is revealed that the composite vulcanizates demonstrate the Payne effect characterized by decay of storage modulus, weak overshoot of loss modulus, and very weak high-order harmonics; this effect is mainly dominated by the rubber matrix experiencing microscopic strain amplitude enlarged by the filler. The composite vulcanizates exhibit the Mullins effect that becomes increasingly marked with increasing filler loading and is partially recovered by thermal annealing at relatively high temperatures. The energy dissipation during cyclic tensions is rooted in the viscoelastic deformation of the matrix and the filler-rubber interfacial debonding. The former is marked at room temperature where the rubber phase undergoes a crystallization-melting process during loading-unloading. The latter being marked in the presence of a small content of AF causes yieldinglike deformation for the virgin composites at low tensile strains, and its contribution to the softening is not recoverable during thermal annealing. The results show that the viscoelastic matrix is of importance in controlling the softening of the composite vulcanizates, which will be of guiding significance to conduct research studies on high-performance rubber composites products.

Evaluating fatigue resistance based on viscoelastic properties of asphalt mixtures

ABSTRACT In this study, the fatigue resistance of different asphalt mixture types subjected to the same aging condition was evaluated using linear viscoelastic properties of asphalt mixtures. The relaxation spectra were determined from the dynamic modulus test based on the linear viscoelastic theory, and the relationship between the parameters of relaxation spectra and the parameters of the storage modulus master-curves were developed. The Texas overlay test was conducted to evaluate the fatigue resistance with the number of load cycle to failure used as the measure of fatigue resistance. From the corresponding results, it is shown that the inflection point frequency of the dynamic modulus master-curves could be used to assess the fatigue resistance compared to other parameters. The Glover-Rowe parameter also exhibited a fair relationship with the fatigue resistance of the asphalt mixtures. The effect of the shape parameter (γ) of the dynamic modulus master-curves was quantified but seemed not very sensitive to fatigue resistance for the asphalt mixtures evaluated. In the study, a new parameter (VECIndex) was developed to evaluate the fatigue resistance, which considered the inflection point frequency and shape of the dynamic modulus master-curves, both of which influence the linear viscoelastic properties and fatigue resistance of asphalt mixtures.

Determining with High Accuracy the Relaxation Modulus and Creep Compliance of Asphaltic Materials in the Form of Sums of Exponential Functions from Mathematical Master Curves of Dynamic Modulus

According to the physical causality principle, the two components of complex modulus are not independent yet interrelated to each other via Kramers-Kronig relationships. Using two mathematical functions to predict simultaneously the dynamic modulus (DM) and phase angle (PA) generally leads to the violation of the causality principle. Therefore, the calculation of one component based on the other one is a vital task for using mathematical models to predict the linear viscoelastic (LVE) behavior of asphaltic materials. In addition, the relaxation modulus (RM) or the creep compliance (CC) in the form of sums of exponential functions (SEFs) is necessary for the efficient resolution of the stress–strain relationship in the time domain. This paper presented a novel method for calculating with high accuracy the RM and CC in the form of SEFs based on the input DM master curve. First, the midpoint integration scheme was used to calculate the PA based on the exact relationship between the PA and DM. After that, the storage modulus and compliance were computed and decomposed with high accuracy into SEFs using a special technique. Then, the closed-form formula of the RM and CC were derived thanks to the special form function of the storage modulus and compliance. Finally, the special technique was used once again to decompose with high accuracy the RM and CC into SEFs for possible uses in finite-element method (FEM) analysis in the time domain. The results showed that the relative errors of all LVE properties computed were lower than 0.1 percent at all calculating points.

Reliability of Calculation of Dynamic Modulus for Asphalt Mixtures Using Different Master Curve Models and Shift Factor Equations.

To develop a mechanistic-empirical pavement design system for Norwegian conditions, this paper evaluates the influence of the adoption of different models and shifting techniques on the determination of dynamic modulus master curves of asphalt mixtures. Two asphalt mixture types commonly used in Norway, namely Asphalt Concrete (AC) and Stone Mastic Asphalt (SMA) containing neat bitumen and polymer-modified bitumen, were prepared by the roller compactor, and their dynamic moduli were determined by the cyclic indirect tensile test. The dynamic modulus master curves were constructed using the standard logistic sigmoidal model, a generalized logistic sigmoidal model and the Christensen–Anderson–Marasteanu model. The shifting techniques consisted of log-linear, quadratic polynomial function, Arrhenius, William–Landel–Ferry and Kaelble methods. The absolute error, normalised square error and goodness-of-fit statistics encompassing standard error ratio and coefficient of determination were used to appraise the models and shifting methods. The results showed that the standard logistic sigmoidal model and the Williams–Landel–Ferry equation had the most suitable fits for the specimens tested. The asphalt mixtures containing neat bitumen had a better fit than the ones containing polymer-modified bitumen. The Kaelble equation and log-linear equation led to similar results. These findings provide a relevant recommendation for the mechanistic-empirical pavement design system.

Moisture susceptibility of asphalt mixtures: 2S2P1D rheological model approach and new index based on dynamic modulus master curve changes

A methodology is proposed for evaluating the induced moisture damage in asphalt mixtures via a new index called the dynamic modulus area ratio (DMAR), which is used to calculate the difference under the areas of the dynamic modulus master curves fitted by the 2S2P1D model before and after conditioning. Were evaluated 21 mixtures applied in the field by comparing data obtained via empirical tests, e.g., the tensile strength ratio and dynamic modulus ratio, using AASHTO T283. The behavior that moisture damage analysis based on stiffness loss measurements in modulus tests can lead to different conclusions than those based on damage resistance tests like TSR. The 2S2P1D model proved to be adequate to evaluate the changes promoted by the deleterious effect of water on the stiffness of the mixtures after the induced moisture damage cycle. For the DMAR, the results clearly differed according to the type of binder, indicating that the impact of water damage on the linear viscoelastic behavior depends on the type of binder used in the mixture. The estimation of susceptibility to moisture using the DMAR, which assesses broader temperature and frequency ranges, enables a stiffness evaluation that is closely related to the field impact on this property, making it possible to evaluate variations in the entire stiffness spectra of the mixtures; thus, it can be used in methods based on the performance for the selection of asphalt mixtures.

Dynamic Characteristic Master Curve and Parameters of Different Asphalt Mixtures

Using an AMPT tester and based on laboratory tests, this paper performed a comparative study on the dynamic characteristics of different asphalt mixtures, analyzed the influence of different asphalt binders on the characteristic parameters of the dynamic modulus master curve and the phase angle master curve of asphalt mixture, and expounds the evaluation function of the phase angle master curve for mixture relaxation characteristics. The results show that the modulus master curve parameters of the asphalt mixture are closely related to voids in the mineral aggregate, mixture density, and asphalt content of the asphalt mixture. For the same kind of asphalt mixture, because the gradation of mineral aggregate is fixed and the volume parameters are almost the same, the ultimate modulus of the mixture at different temperatures is unique; when the temperature changes or the asphalt changes, the shape parameter β of the modulus master curve changes regularly, which brings different dynamic responses, and the lower β will show the characteristics of a higher modulus. Asphalt is the source of the viscoelasticity of the asphalt mixture. Although the influence of particle gradation of the mixture will bring about the change of modulus, the phase angle of the mixture depends on the viscoelastic properties of asphalt, and the initial phase angle in the main curve is positively correlated with asphalt penetration and negatively correlated with the softening point and viscosity, while the peak phase angle A is negatively correlated with penetration, and the softening point viscosity is positively correlated. The viscoelastic interval, represented by ω, is negatively correlated with penetration but positively correlated with the softening point and viscosity. The peak position, parameter ωc, of the phase angle master curve can evaluate the relaxation characteristics of the mixture, and the crack resistance of different mixtures can be compared without complex model calculation. In the comparison of the relaxation time of asphalt mixture, the relaxation time of foam cold-recycled mixture is the largest, which is significantly higher than that of other forms of cement mixture; the emulsified asphalt cold-recycled mixture is equivalent to AC20 and LSPM30 mixtures; the SBS-modified asphalt mixture has the best relaxation characteristics.

Influence of Confinement Pressure on the Mechanical Response of Emulsified Cold-Recycled Mixtures

Cold recycling of asphalt pavement is an effective rehabilitation technique in terms of saving natural resources and cost of construction. The current study focuses on cold-recycled asphalt mixture designated as emulsified cold-recycled mixture (ECRM) that contains 100% reclaimed asphalt pavement material and slow-setting asphalt emulsion. Here, a repeated haversine compression test is conducted with and without confinement pressure at six temperatures (0°C, 10°C, 20°C, 30°C, 40°C, and 50°C) and 10 frequencies (25, 20, 10, 5, 2, 1, 0.5, 0.2, 0.1, and 0.01 Hz). The stress–strain–time response of ECRM is investigated, and it is observed that the influence of confinement pressure is negligible in the temperature range of 0°C–10°C, whereas it is significant at temperature 30°C and higher, irrespective of the frequency of loading. However, at 20°C, the influence of confinement pressure is negligible at higher frequencies (25–10 Hz), and it is significant at lower frequencies (less than 10 Hz). The viscoelastic response of ECRM is seen at all temperature, frequency, and confinement conditions of loading from the analyzed Lissajous plots. The dynamic modulus and phase angle are computed using the regression and the fast Fourier-transform (FFT) methods. The dynamic modulus and phase angle master curve is then generated using a free-shifting approach and a model-based approach. The model-based approach involves the numerical solution of the exact Kramers–Kronig relations combined with the generalized logistic sigmoidal model. The FFT-based dynamic modulus is used to construct a master curve with the generalized logistic sigmoidal model. Such a model-based master curve resulted in excellent predictive capabilities for dynamic modulus, and hence it is suggested for ECRM.

An experimental length scale investigation on viscoelastic behavior of bituminous composites: Focusing on mortar scale

The mortar component plays an essential role in forming different asphalt mixture distresses. The fine aggregate size affects the viscoelastic behavior of mortar. In this study, three cutting sizes of 3.35, 2.36, and 1.7 mm, on the aggregate grading curve were considered to construct the mortar scales, namely mortar (I), (II), and (III), respectively. With a unique loading mode, a frequency sweep test was performed on four different length scales, including bitumen, asphalt mastic, mortar, and asphalt mixture, to make a direct comparison through a multi-scale approach. Also, a stress sweep test was conducted to find the mortar scale's linear viscoelastic domain. The results indicate that different mortar types have variable linear viscoelastic domains. The master curves of dynamic modulus (E*) and phase angle (δ) show that adding filler to bitumen has more effect on the E* than the δ. Although scaling up from the mastic to mortar (II) causes a significant difference between the viscoelastic parameters, the results remained approximately the same. The main gap between the mixture and mentioned sub-scales is filled with mortar (I). While the Cole-Cole diagrams demonstrate that the bitumen to mortar (II) scales have the same behavior, the closest scale to the mixture is the mortar (I). Therefore, using a cutting size of 3.35 mm is recommended to fabricate mortar (for asphalt mixture with a nominal maximum aggregate size of 19 mm) instead of 2.36 mm, which was suggested in previous studies.