Fine Particle Mass Concentrations Research Articles

Distribution Characteristics of the Number and Mass Concentrations of Respiratory Fine Particles in the Areas Around Coal-fired Power Plants

Distribution Characteristics of the Number and Mass Concentrations of Respiratory Fine Particles in the Areas Around Coal-fired Power Plants

Contrasting intra-urban variability of ultrafine particle number and fine particle mass concentrations in Dhaka, Bangladesh, and Pittsburgh, USA

In this study, we investigated the intra-urban variability of fine particle mass (PM2.5) and ultrafine particle number concentration (PNC) in Dhaka (Bangladesh), and Pittsburgh (USA), two cities with vastly different pollution sources and levels. We collected measurements of PNC and PM2.5 at a wide range of sites spanning a variety of urban land use attributes (35 sites in Dhaka and 30 sites in Pittsburgh). We found that PNC levels exhibited a 3-4-fold variability between sites in each city, ranging from 20,000–100,000 # cm−3 in Dhaka and 7,000–28,000 # cm−3 in Pittsburgh. PM2.5 levels varied within 50% of the urban background level, ranging from 80 to 110 μg m−3 in Dhaka and 6–12 μg m−3 in Pittsburgh. We observed a moderate level of spatial correlation between PNC and PM2.5 measurements in both cities (R2 0.3 in Dhaka, and 0.4 in Pittsburgh), and consistent within-city spatial patterns in different meteorological seasons. Compared to the Pittsburgh levels, both PNC and PM2.5 levels in Dhaka were significantly higher, however, PM2.5 was disproportionately higher (10–12 times higher) than PNC (3–4 times higher). The slope of PNC versus PM2.5 varied significantly between the two cities, suggesting that the sources and size distribution of particles that make up the majority of the PM2.5 were different in the two cities. The results found in Dhaka indicate that aerosol particles are influenced by solid fuel combustion, including solid biomass burning, waste burning, and road dust, which have a greater impact on particle mass concentration due to their larger size. Contrary, in Pittsburgh, traffic (gasoline and diesel combustion) particles, relatively smaller in size compared to solid fuel combustion particles, play a dominant role in determining the within-city variability of PNC and PM2.5. Our findings suggest that while controlling traffic emissions can contribute to reducing PNC, substantial efforts will be required to mitigate accumulation mode particles from various region-specific sources in order to decrease PM2.5 mass concentrations in Dhaka.

Study of particulate emissions when using special wires for underwater welding

The article describes the study to evaluate the emissions to atmospheric air of airborne nano- and microparticles generated during underwater welding in seawater from Ajax Bay (Sea of Japan) using special wires and coated electrodes. The most commonly used underwater industrial production processes were selected: semi-automatic (mechanized) underwater welding with a welding wire, manual welding with electrodes, and semi-automatic (mechanized) underwater cutting with a welding wire for cutting. An aerosol particle counter was used to determine the mass concentration of fine aerosol particles in the air of the working area above the aquarium. The highest number of suspended particles in the atmospheric air was observed in the process of underwater welding with a welding electrode. Comparing the welding wire and the welding electrode for underwater welding, it can be concluded that the welding wire is less dangerous for people, which is confirmed by the lower amount of suspended particles emitted into the atmospheric air during its use.

Low-Cost Particulate Matter Sensors for Monitoring Residential Wood Burning.

Conventional monitoring systems for air quality, such as reference stations, provide reliable pollution data in urban settings but only at relatively low spatial density. This study explores the potential of low-cost sensor systems (LCSs) deployed at homes of residents to enhance the monitoring of urban air pollution caused by residential wood burning. We established a network of 28 Airly (Airly-GSM-1, SP. Z o.o., Poland) LCSs in Kristiansand, Norway, over two winters (2021-2022). To assess performance, a gravimetric Kleinfiltergerät measured the fine particle mass concentration (PM2.5) in the garden of one participant's house for 4 weeks. Results showed a sensor-to-reference correlation equal to 0.86 for raw PM2.5 measurements at daily resolution (bias/RMSE: 9.45/11.65 μg m-3). High-resolution air quality maps at a 100 m resolution were produced by combining the output of an air quality model (uEMEP) using data assimilation techniques with the network data that were corrected and calibrated by using a proposed five-step network data processing scheme. Leave-one-out cross-validation demonstrated that data assimilation reduced the model's RMSE, MAE, and bias by 44-56, 38-48, and 41-52%, respectively.

Effectiveness of equipping bus stop shelters with cooling and filtering systems in a city with tropical climate

PurposeWaiting for a bus may represent a period of intense exposure to traffic particles in hot and noisy conditions in the street. To lessen the particle load and tackle heat in bus stops a shelter was equipped with an electrostatic precipitator and a three-step adiabatic cooling system capable of dynamically adjust its operation according to actual conditions. This study evaluates the effectiveness of the Airbitat Oasis Smart Bus Stop, as the shelter was called, to provide clean and cool air.Design/methodology/approachThe particle exposure experienced in this innovative shelter was contrasted with that in a conventional shelter located right next to it. Mass concentrations of fine particles and black carbon, and particle number concentration (as a proxy of ultrafine particles) were simultaneously measured in both shelters. Air temperature, relative humidity and noise level were also measured.FindingsThe new shelter did not perform as expected. It only slightly reduced the abundance of fine particles (−6.5%), but not of ultrafine particles and black carbon. Similarly, it reduced air temperature (−1 °C), but increased relative humidity (3%). Its operation did not generate additional noise.Practical implicationsThe shelter's poor performance was presumably due to design flaws induced by a lack of knowledge on traffic particles and fluid dynamics in urban environments. This is an example where harnessing technology without understanding the problem to solve does not work.Originality/valueIt is uncommon to come across case studies like this one in which the performance and effectiveness of urban infrastructure can be assessed under real-life service settings.

Ten questions concerning indoor ultrafine particles

Ultrafine particles (≤100 nm in diameter) are the smallest condensed-phase materials in air. By number, they are the most abundant particles both outdoors and indoors. Because of their small size, they contribute little to mass concentrations of fine particles, a regulated air pollutant with large associated health risks. Inhaling ultrafine particles raises health concerns, in part owing to their ability to migrate from the site of deposition in the respiratory tract. Buildings provide partial protection against ultrafine particles of outdoor origin. The degree of that protection is broadly variable, influenced by particle size and by building design and operational factors, such as ventilation rates and the efficiency of particle filters. Because of the large proportion of time spent by people indoors, much exposure to ultrafine particles occurs in buildings, even for particles of outdoor origin. Diverse indoor sources, including cooking and the use of candles, contribute materially to indoor ultrafine particle concentrations. Indoor sourced ultrafine particle concentrations are also influenced by building design and operational factors. Whether of indoor or outdoor origin, dynamic processes influence the concentrations, sizes, and chemical composition of ultrafine particles. Such processes include deposition to indoor surfaces, coagulation, and sorptive partitioning of semivolatile organic compounds. Advancing scientific and technical knowledge about building factors and dynamic processes that influence indoor ultrafine particle concentrations can contribute (a) to better understanding of associated health risks and (b) to the more effective design and implementation of mitigation strategies and technologies.

Analysis of new particle formation events and comparisons to simulations of particle number concentrations based on GEOS-Chem–advanced particle microphysics in Beijing, China

Abstract. Aerosol particles play important roles in air quality and global climate change. In this study, we analyze the measurements of particle size distribution from 12 March to 6 April 2016 in Beijing to characterize new particle formation (NPF) using the observational data of sulfuric acid, meteorological parameters, solar radiation, and the mass concentration of fine particles (PM2.5, particulate matter with diameters less than 2.5 µm). During this 26 d campaign, 11 new particle formation events are identified with obvious bursts of sub-3 nm particle number concentrations and subsequent growth of these nucleated particles. It is found that sulfuric acid concentration in Beijing does not have a significant difference between NPF event and non-event days. Low relative humidity (RH) and high daily total solar radiation appear to be favorable for the occurrence of NPF events, which is quite obvious in this campaign. The simulations using four nucleation schemes, i.e., H2SO4–H2O binary homogeneous nucleation (BHN), H2SO4–H2O–NH3 ternary homogeneous nucleation (THN), H2SO4–H2O–ion binary ion-mediated nucleation (BIMN), and H2SO4–H2O–NH3–ion ternary ion-mediated nucleation (TIMN), based on a global chemistry transport model (GEOS-Chem) coupled with an advanced particle microphysics (APM) model, are conducted to study the particle number concentrations and new particle formation process. Our comparisons between measurements and simulations indicate that the BHN scheme and BIMN scheme significantly underestimate the observed particle number concentrations, and the THN scheme captures the total particle number concentration on most NPF event days well but fails to capture the noticeable increase in particle number concentrations on 18 March and 1 April. The TIMN scheme has obvious improvement in terms of total and sub-3 nm particle number concentrations and nucleation rates. This study provides a basis for further understanding of the nucleation mechanism in Beijing.

Analysis of the urban turbidity island effect: a case study in Beijing City, China

The urban turbidity island (UTI) effect is an important research topic in urban climate studies. It is closely related to urban visibility and the health of urban residents; however, it has received little attention in previous research. This study analyzes the temporal and spatial distribution characteristics of the UTI effect through the combined use of satellite remote sensing and ground observation data. Specifically, absolute and relative urban turbidity island intensity (UTII_A and UTII_R) indices are proposed and calculated for 2000–2020 by using aerosol data products and atmospheric fine particle mass concentration inversion products, which are represented by aerosol optical depth (AOD), PM1, PM2.5, and PM10. The results show the following: (a) there has been a clear footprint of the UTI effect in Beijing since 2000, generally consistent with trends of urban sprawl; (b) there are great differences in the interannual distribution of AOD, normalized AOD and PM values in urban and suburban areas; and (c) there are seasonal differences in the UTI distribution and air pollutant concentrations. The differences among indices between urban and suburban areas are mainly caused by heat island-induced air convection, complex structures in urban areas and regional weather conditions. Importantly, the interannual distribution of AOD and UTII_A of PM values decreased from 2014 to 2020, indicating that the government’s air pollution control policy has significantly improved air quality. Analysis from this study could support the formulation of urban planning and control policies to guide human activities.

Indoor Exposure and Regional Inhaled Deposited Dose Rate during Smoking and Incense Stick Burning-The Jordanian Case as an Example for Eastern Mediterranean Conditions.

Tobacco smoking and incense burning are commonly used in Jordanian microenvironments. While smoking in Jordan is prohibited inside closed spaces, incense burning remains uncontrolled. In this study, particle size distributions (diameter 0.01-25 µm) were measured and inhaled deposited dose rates were calculated during typical smoking and incense stick-burning scenarios inside a closed room, and the exposure was summarized in terms of number and mass concentrations of submicron (PNSub) and fine particles (PM2.5). During cigarette smoking and incense stick-burning scenarios, the particle number concentrations exceeded 3 × 105 cm-3. They exceeded 5 × 105 cm-3 during shisha smoking. The emission rates were 1.9 × 1010, 6.8 × 1010, and 1.7 × 1010 particles/s, respectively, for incense, cigarettes, and shisha. That corresponded to about 7, 80, and 120 µg/s, respectively. Males received higher dose rates than females, with about 75% and 55% in the pulmonary/alveolar during walking and standing, respectively. The total dose rates were in the order of 1012-1013 #/h (103-104 µg/h), respectively, for PNSub and PM2.5. The above reported concentrations, emissions rates, and dose rates are considered seriously high, recalling the fact that aerosols emitted during such scenarios consist of a vast range of toxicant compounds.

Multi-instrument assessment of fine and ultrafine titanium dioxide aerosols

ABSTRACT The measurement of fine (diameter: 100 nanometers–2.5 micrometers) and ultrafine (UF: < 100 nanometers) titanium dioxide (TiO2) particles is instrument dependent. Differences in measurements exist between toxicological and field investigations for the same exposure metric such as mass, number, or surface area because of variations in instruments used, operating parameters, or particle-size measurement ranges. Without appropriate comparison, instrument measurements create a disconnect between toxicological and field investigations for a given exposure metric. Our objective was to compare a variety of instruments including multiple metrics including mass, number, and surface area (SA) concentrations for assessing different concentrations of separately aerosolized fine and UF TiO2 particles. The instruments studied were (1) DustTrak™ DRX, (2) personal DataRAMs™ (PDR), (3) GRIMMTM, and (4) diffusion charger (DC). Two devices of each field-study instrument (DRX, PDR, GRIMM, and DC) were used to measure various metrics while adjusting for gravimetric mass concentrations of fine and UF TiO2 particles in controlled chamber tests. An analysis of variance (ANOVA) was used to apportion the variance to inter-instrument (between different instrument-types), inter-device (within instrument), and intra-device components. Performance of each instrument-device was calculated using root mean squared error compared to reference methods: close-faced cassette and gravimetric analysis for mass and scanning mobility particle sizer (SMPS) real-time monitoring for number and SA concentrations. Generally, inter-instrument variability accounted for the greatest (62.6% or more) source of variance for mass, and SA-based concentrations of fine and UF TiO2 particles. However, higher intra-device variability (53.7%) was observed for number concentrations measurements with fine particles compared to inter-instrument variability (40.8%). Inter-device variance range(0.5–5.5%) was similar for all exposure metrics. DRX performed better in measuring mass closer to gravimetric than PDRs for fine and UF TiO2. Number concentrations measured by GRIMMs and SA measurements by DCs were considerably (40.8–86.9%) different from the reference (SMPS) method for comparable size ranges of fine and UF TiO2. This information may serve to aid in interpreting assessments in risk models, epidemiologic studies, and development of occupational exposure limits, relating to health effect endpoints identified in toxicological studies considering similar instruments evaluated in this study.

Formation and impacts of nitryl chloride in Pearl River Delta

Abstract. Here we present a field measurement of ClNO2 (nitryl chloride) and N2O5 (dinitrogen pentoxide) by a time-of-flight chemical ionization mass spectrometer (ToF-CIMS) with the Filter Inlet for Gas and AEROsols (FIGAERO) at a regional site in the Pearl River Delta during a photochemical pollution season from 26 September to 17 November 2019. Three patterns of air masses are sampled during this campaign, including the dominating air masses from the north and northeast urban regions (Type A), the southeast coast (Type B), and the South China Sea (Type C). The concentration of ClNO2 and N2O5 was observed to be much higher in Type A and B than in Type C, indicating that the urban nighttime chemistry is more active than the background marine regions. The N2O5 uptake coefficient and ClNO2 production yield were estimated based on the field measurement, and the performance of the previously derived parameterizations was assessed. The nighttime ClNO2 correlated with particulate chloride and the mass concentration of fine particles (most likely due to aerosol surface area) suggested that the ClNO2 formation was limited by the N2O5 uptake at this site. By examining the relationship between particulate chloride and other species, we implied that anthropogenic emissions (e.g., biomass burning) rather than sea salt particles dominate the origin of particulate chloride, although the site was only about 100 km away from the ocean. A box model with detailed chlorine chemistry is used to investigate the impacts of ClNO2 chemistry on atmospheric oxidation. Model simulations showed that the chlorine radical liberated by ClNO2 photolysis during the next day had a slight increase in concentrations of OH, HO2, and RO2 radicals, as well as minor contributions to RO2 radical and O3 formation (&lt; 5 %, on daytime average), in all the three types of air masses. Relatively high contributions were observed in Type A and B. The overall low contributions of ClNO2 to atmospheric oxidation are consistent with those reported recently from wintertime observations in China (including Shanghai, Beijing, Wangdu, and Mt. Tai). This may be attributed to the following: (1) relatively low particle mass concentration limited ClNO2 formation; (2) other reactions channels, like nitrous acid (HONO), oxygenated volatile organic compounds (OVOCs, including formaldehyde), and ozone photolysis had a more significant radical formation rate during the ozone pollution episodes and weakened the ClNO2 contribution indirectly. The results provided scientific insights into the role of nighttime chemistry in photochemical pollution under various scenarios in coastal areas.

Effect of mixed magnetic field on physical properties of atmospheric suspended fine particles

In recent years, the fine particles suspended in the atmosphere, especially the particle size less than 10 μm, have caused very adverse effects on the climate environment and human health. However, the current research on the causes of air pollution mainly focuses on human activities and weather conditions. Considering the weak magnetism and chargeability of atmospheric fine particles, this study proposed a new view that space electromagnetic radiation may affect the physical properties of fine particles. We first analyzed the dynamic characteristics of magnetic micro-particle in the electromagnetic environment, and built a simulation model in the COMSOL simulation software. Finally, based on the theoretical analysis and simulation results, we built an experimental verification system to evaluate the effects of electromagnetic radiation on the physical properties of micro-particle, and carried out a 30-day control experiment. The experimental results showed that the physical properties such as particle size distribution, mass concentration, and morphology of suspended fine particles in the atmosphere under electromagnetic radiation are significantly different from those under non-electromagnetic radiation environment. It can be inferred that the aggregation, fusion, and deposition of suspended particles in the atmosphere are closely related to the complex electromagnetic environment in space.

Air Pollution and Pediatric Respiratory Hospitalizations: Effect Modification by Particle Constituents and Oxidative Potential.

Rationale: Outdoor particulate and gaseous air pollutants impair respiratory health in children, and these associations may be influenced by particle composition. Objectives: To examine whether associations between short-term variations in fine particulate air pollution, oxidant gases, and respiratory hospitalizations in children are modified by particle constituents (metals and sulfur) or oxidative potential. Methods: We conducted a case-crossover study of 10,500 children (0-17 years of age) across Canada. Daily fine particle mass concentrations and oxidant gases (nitrogen dioxide and ozone) were collected from ground monitors. Monthly estimates of fine particle constituents (metals and sulfur) and oxidative potential were also measured. Conditional logistic regression models were used to estimate associations between air pollutants and respiratory hospitalizations, above and below median values for particle constituents and oxidative potential. Measurements and Main Results: Lag-1 fine particulate matter mass concentrations were not associated with respiratory hospitalizations (odds ratio and 95% confidence interval per 10 μg/m3 increase in fine particulate matter: 1.004 [0.955-1.056]) in analyses ignoring particle constituents and oxidative potential. However, when models were examined above or below median metals, sulfur, and oxidative potential, positive associations were observed above the median. For example, the odds ratio and 95% confidence interval per 10 μg/m3 increase in fine particulate matter were 1.084 (1.007-1.167) when copper was above the median and 0.970 (0.929-1.014) when copper was below the median. Similar trends were observed for oxidant gases. Conclusions: Stronger associations were observed between outdoor fine particles, oxidant gases, and respiratory hospitalizations in children when metals, sulfur, and particle oxidative potential were elevated.

Evaluation of Mass Concentration and Size Distribution of Fine Particles (PM2.5) in Bien Hoa City, Dong Nai Province

Air pollution is one of the most concerning environmental issues, in which fine inhalable particles (PM2.5, with diameters that are generally 2.5 micrometers and smaller) concentration plays a key part. Bien Hoa city contains and locates close to several large industrial zones that might create sources of PM2.5 polluting the local air quality. This study monitors and evaluates PM2.5 concentration trends in Bien Hoa airport of Dong Nai province. PM samples are analyzed by Scanning Electron Microscopy (SEM) to recognize the surface pattern and size distributions are analyzed by ImageJ software. Ten samples of PM2.5 were obtained from sampling collected in October 2021. The results show that 24-h PM2.5 mass concentrations were from 15.2 µg/m3 - 50.4 µg/m3 with an average of 28.2 µg/m3; median of 24.1 µg/m3; and standard deviation of 12.2 µg/m3. The values are lower than the Vietnam National Technical Regulation on Ambient Air Quality (QCVN 05:2013/BTNMT) but far higher than the recommended values of the World Health Organization (WHO). SEM and image results indicate the distributions of the particles of 2.0 - 2.5 µm are minor, where the majority are particles with aerodynamic diameter ≤ 1.0 µm.&#x0D; Keywords: Air pollution; Fine particulate matters; PM2.5; Size distribution, Bien Hoa, Dong Nai.

Exploring the Sensitivity of Visibility to PM2.5 Mass Concentration and Relative Humidity for Different Aerosol Types

Fine particle (PM2.5) mass concentration and relative humidity (RH) are the primary factors influencing atmospheric visibility. There are some studies focused on the complex, nonlinear relationships among visibility, PM2.5 concentration, and RH. However, the relative contribution of the two factors to visibility degradation, especially for different aerosol types, is difficult to quantify. In this study, the normalized forward sensitivity index method for identifying the dominant factors of visibility was used on the basis of the sensitivity of visibility to PM2.5 and RH changes. The visibility variation per unit of PM2.5 or RH was parameterized by derivation of the visibility multivariate function. The method was verified and evaluated based on 4453 valid hour data records in Tianjin, and visibility was identified as being in the RH-sensitive regime when RH was above 75%. In addition, the influence of aerosol chemical compositions on sensitivity of visibility to PM2.5 and RH changes was discussed by analyzing the characteristics of extinction components ((NH4)2SO4, NH4NO3, organic matter, and elemental carbon) measured in Tianjin, 2015. The result showed that the fitting equation of visibility, PM2.5, and RH, separately for different aerosol types, further improved the accuracy of the parameterization scheme for visibility in most cases.

Source Analysis of Ambient PM2.5 in Wuhan City Based on Random Forest Model

Based on the online monitoring data of fine particle(PM2.5) mass concentration, carbonaceous components, ionic constituents, and elemental components in an urban site of Wuhan from December 2019 to November 2020, the chemical characteristics of PM2.5 were analyzed. In addition, seasonal source apportionment of PM2.5 was conducted using the principal component analysis(PCA) method and random forest(RF) algorithm model. The results indicated that ρ(PM2.5) was the highest in winter[(61.33±35.32) μg·m-3] and the lowest in summer[(17.87±10.06) μg·m-3]. Furthermore, organic carbon(OC), with a concentration of(7.27±3.51) μg·m-3, accounted for the major proportion compared with that of elemental carbon(EC) in the carbonaceous component of PM2.5. NO3-, SO42-, and NH4+ had the highest proportion in ionic components, with concentrations of (11.55±3.86),(7.55±1.53), and (7.34±1.99) μg·m-3, respectively. K, Fe, and Ca were the main elements in elemental components, with concentrations of (752.80±183.98),(542.34±142.55), and (459.70±141.99) ng·m-3, respectively. Relying on main factor extraction by PCA and quantitative analysis by RF, five emission sources were ultimately confirmed. The seasonal concentration distribution of these emission sources was as follows:coal burning and secondary sources(46%, 39%, 41%, and 52% for spring, summer, autumn, and winter, respectively) made the highest contribution to PM2.5, followed by vehicle emission sources(22%, 28%, 27%, and 21%), industrial emission sources (14%, 18%, 17%, and 13%), dust sources (10%, 8%, 6%, and 6%), and biomass burning sources (8%, 7%, 9%, and 8%). The valuation of the RF model was evaluated using multiple indicators, including RMSE, MSE, and R2. The evaluation results showed that the model for winter had the best performance (R2=0.974, RMSE=3.795 μg·m-3, MAE=2.801 μg·m-3), the models for spring (R2=0.936, RMSE=3.512 μg·m-3, MAE=2.503 μg·m-3) and autumn (R2=0.937, RMSE=4.114 μg·m-3, MAE=3.034 μg·m-3) performed with moderate-fitting goodness, and the summer model showed a relatively weak-fitting performance (R2=0.866, RMSE=5.665 μg·m-3, MAE=3.889 μg·m-3). The RF model had a satisfactory performance in PM2.5 source apportionment and had excellent prospects in analyzing massive historical data of air pollutants.

Field Studies on the Removal Characteristics of Particulate Matter and SOx in Ultra-Low Emission Coal-Fired Power Plant

In order to reduce the environmental smog caused by coal combustion, air pollution control devices have been widely used in coal-fired power plants, especially of wet flue gas desulfurization (WFGD) and wet electrostatic precipitator (WESP). In this work, particulate matter with aerodynamic diameter less than 10 μm (PM10) and sulfur oxides (SOx) have been studied in a coal-fired power plant. The plant is equipped with selective catalytic reduction, electrostatic precipitator, WFGD, WESP. The results show that the PM10 removal efficiencies in WFGD and WESP are 54.34% and 50.39%, respectively, and the overall removal efficiency is 77.35%. WFGD and WESP have effects on the particle size distribution. After WFGD, the peak of particles shifts from 1.62 to 0.95 μm, and the mass concentration of fine particles with aerodynamic diameter less than 0.61 μm increases. After WESP, the peak of particle size shifts from 0.95 to 1.61 μm. The differences are due to the agglomeration and growth of small particles. The SO3 mass concentration increases after SCR, but WFGD has a great influence on SOx with the efficiency of 96.56%. WESP can remove SOx, but the efficiency is 20.91%. The final emission factors of SO2, SO3, PM1, PM2.5 and PM10 are 0.1597, 0.0450, 0.0154, 0.0267 and 0.0215 (kg · t−1), respectively. Compared with the research results without ultra-low emission retrofit, the emission factors are reduced by 1~2 orders of magnitude, and the emission control level of air pollutants is greatly improved.

Predicting Spatial Variations in Multiple Measures of PM2.5 Oxidative Potential and Magnetite Nanoparticles in Toronto and Montreal, Canada.

There is growing interest to move beyond fine particle mass concentrations (PM2.5) when evaluating the population health impacts of outdoor air pollution. However, few exposure models are currently available to support such analyses. In this study, we conducted large-scale monitoring campaigns across Montreal and Toronto, Canada during summer 2018 and winter 2019 and developed models to predict spatial variations in (1) the ability of PM2.5 to generate reactive oxygen species in the lung fluid (ROS), (2) PM2.5 oxidative potential based on the depletion of ascorbate (OPAA) and glutathione (OPGSH) in a cell-free assay, and (3) anhysteretic magnetic remanence (XARM) as an indicator of magnetite nanoparticles. We also examined how exposure to PM oxidative capacity metrics (ROS/OP) varied by socioeconomic status within each city. In Montreal, areas with higher material deprivation, indicating lower area-level average household income and employment, were exposed to PM2.5 characterized by higher ROS and OP. This relationship was not observed in Toronto. The developed models will be used in epidemiologic studies to assess the health effects of exposure to PM2.5 and iron-rich magnetic nanoparticles in Toronto and Montreal.

A Method to Generate Experimental Aerosol with Similar Particle Size Distribution to Atmospheric Aerosol

The SARS-CoV virus spreads in the atmosphere mainly in the form of aerosols. Particle air filters are widely used in indoor heating, ventilation, and air-conditioning (HVAC) systems and filtration equipment to reduce aerosol concentration and improve indoor air quality. Requirements arise to rate filters according to their mass-based filtration efficiency. The size distribution of test aerosol greatly affects the measurement results of mass-based filtration efficiency and dust loading of filters, as well as the calibration of optical instruments for fine-particle (PM2.5) mass concentration measurement. The main objective of this study was to find a new method to generate a chemically nontoxic aerosol with a similar particle size distribution to atmospheric aerosol. We measured the size distribution of aerosols generated by DEHS (di-ethyl-hexyl-sebacate), PSL (poly-styrene latex), olive oil, and 20% sucrose solution with a collision nebulizer in a wide range of 15 nm–20 μm. Individually, none of the solutions generated particles that share a similar size distribution to atmospheric aerosol. We found that the 20% sucrose solution + olive oil mixture solution (Vss:Voo = 1:2) could be used to generate a chemically nontoxic aerosol with similar particle number/volume size distribution to the atmospheric aerosol (t-test, p &lt; 0.05). The differences in the mass-base filtration efficiency measured by the generated aerosol and the atmospheric aerosol were smaller than 2% for MERV 7, 10, 13, and 16 rated filters. The aerosol generated by the new method also performed well in the calibration of optical-principle-based PM2.5 concentration measurement instruments. The average relative difference measured by a tapered element oscillating microbalance (TEOM) and a Dusttrak Model 8530 (calibrated by aerosol generated by the new method) was smaller than 5.8% in the real-situation measurement.

Quartz crystal microbalance with thermally-controlled surface adhesion for an efficient fine dust collection and sensing

The mass concentration of fine dust or particles acts as a standard measure to express the severity of air pollution. In connection with this, many related sensor technologies have been suggested for both indoor and outdoor uses. Among several technologies, the direct measurement of the dust mass using resonant platforms is the most preferable as it possesses multiple advantages including high sensitivity, low limit of detection, and a rapid response time. Such sensor performances directly rely on the adhesion quality between the sensor substrate and dust. In this work, we introduce a thermally controlled dust capturing scheme by integrating a polystyrene (PS) layer and microheater on quartz crystal microbalance (QCM). The Pt microheater can rapidly heat the sensor up to 100 °C, allowing a controlled switching between the soft and hard conditions of the PS film at a rapid rate. When the film is soft, the sensor can capture dust particle efficiently and we can calibrate the attached particle mass by measuring the resonance response. Compared to a bare QCM, our sensor used in this study exhibits 11 times larger detectable mass range. In addition, heated QCMs show a performance that is comparable to a high-cost particle sensing equipment such as an aerodynamic particle sizer and optical particle counter