Martensitic Alloys Research Articles

Inhomogeneous distribution of oxides in various 9Cr ODS alloys and their mechanical performance at room temperature and 650 °C

Oxide dispersion strengthened (ODS) steels have been considered as promising structural materials for fusion reactors. In fabricating ODS steels, homogenous distribution of nano-sized oxides is always expected. In this work, Ti and C were respectively added into the 9Cr alloy with 2 wt% Mn, and the effects of individual Ti addition on microstructure and mechanical performance of ODS alloys are studied. Regularly distributed oxides were revealed in the 9Cr alloys fabricated by hot isostatic pressing (HIP), irrespective of alloying compositions, which indicates the strong interaction between oxides and phase interface. Alloying elements within the matrix can be incorporated into these regularly distributed oxides. Oxide nanoparticles will affect the phase transformation behaviors and the microstructure of as-HIPed 9Cr alloys without oxides is different from that of 9Cr ODS alloys. By performing post-HIP heat treatments, the matrix conditions of 9Cr ODS alloys can be adjusted, and ferritic and martensitic 9Cr ODS alloys are respectively obtained. With tensile tests at room temperature and 650 °C, effects of oxides and matrix conditions on 9Cr alloys were evaluated. It is found that individual Ti addition has a softening effect on the 9Cr alloys, despite that whether oxides are added. Simultaneous addition of Ti and C can improve the strength of 9Cr alloys evidently. Poor ductility at 650 °C is a critical issue for 9Cr ODS alloys, while the 9Cr alloys without oxides have favorable combination of strength and ductility at both room temperature and 650 °C.

Effect of H2S on the corrosion behavior of austenitic and martensitic steels in supercritical CO2 at 550 °C and 20 MPa for Brayton cycle system

Corrosion of alloy materials significantly influences the stability and efficiency of the supercritical carbon dioxide (S-CO2) Brayton cycle. In this study, we investigated the corrosion behavior of the austenitic alloy SP2215 and the martensitic alloy X19CrMoNbVN11-19 (X19) in S-CO2 at 550°C and 20 MPa. The effect of impurities, H2S, on corrosion behavior was studied. After 900 hours, SP2215 formed a 1.1 μm thick oxide layer (Cr2O3). X19 formed a loose and porous double oxide layer of 4.1 μm (outer: Fe3O4, inner: FeCr2O4). After H2S doping, SP2215 had an oxide layer of 6.2 μm (FeS, SiO2, and Cr2O3), while X19 was 9.8 μm (outer: Fe3O4, SiO2, FexSy and Fe2O3, inner: FeCr2O4, Fe2SiO4 and Cr2S3). Metal sulfides formed and the corrosion layer thickened. This indicates that H2S not only changes the corrosion mechanism but also aggravates the corrosion. However, the corrosion of CO2 is dominant. SP2215 has better corrosion resistance than X19.

Compliant Lattice Modulations Enable Anomalous Elasticity in Ni-Mn-Ga Martensite.

High mobility of twin boundaries in modulated martensites of Ni-Mn-Ga-based ferromagnetic shape memory alloys holds a promise for unique magnetomechanical applications. This feature has not been fully understood so far, and in particular, it has yet not been unveiled what makes the lattice mechanics of modulated Ni-Mn-Ga specifically different from other martensitic alloys. Here, results of dedicated laser-ultrasonic measurements on hierarchically twinned five-layer modulated (10M) crystals fill this gap. Using a combination of transient grating spectroscopy and laser-based resonant ultrasound spectroscopy, it is confirmed that there is a shear elastic instability in the lattice, being significantly stronger than in any other martensitic material and also than what the first-principles calculations for Ni-Mn-Ga predict. The experimental results reveal that the instability is directly related to the lattice modulations. A lattice-scale mechanism of dynamic faulting of the modulation sequence that explains this behavior is proposed; this mechanism can explain the extraordinary mobility of twin boundaries in 10M.

Evaluation and Modeling of the Rate of Formation of Lath Martensite in Fe-C Alloys, Extracted from Ultra-Rapid Quenching Experiments

Isothermal information is rarely available for the formation of martensite in Fe or Fe alloys due to a very high rate of transformation compared to the rate of heat conduction. Such information has now been extracted for lath martensite in some sets of Fe alloys from available information on ultra-rapid quenching but only at a single temperature for each alloy, related to its two MS temperatures. The temperature dependence could, thus, be studied only on binary sets of alloys. Those results have been applied to mathematical models based on the Arrhenius equation and illustrated with Arrhenius plots. For three sets of binary Fe alloys, a large group of rates came close to the rate of an almost pure and carbon-free Fe-C alloy. It illustrated that Cr, Ni, and Ru in low contents have relatively small effects on the rate of formation of lath martensite in Fe. It also demonstrated that the present measurements have considerable reproducibility. In contrast, a set of Fe-C alloys did not give a straight line in the Arrhenius plot. Using a new mathematical model based on the concept of the Arrhenius equation to express the effect of carbon, it was possible to predict the rate of formation of lath martensite for Fe-C alloys with fixed C content and their temperature dependencies which are not available experimentally due to the very high rate of formation.

Multi-Force Bio-Active™ Archwires and Various Contemporary NiTi Multi-Force Archwires: Properties and Characteristics-A Review.

The manufacturing of orthodontic archwires made from NiTi alloy has undergone numerous changes from the second half of the last century to modern times. Initially, superelastic-active austenitic NiTi alloys were predominant, followed by thermodynamic-active martensitic NiTi alloys, and, finally, the most recent development was graded thermodynamic alloys. These advancements have been the subject of extensive investigation in numerous studies, as they necessitated a deeper understanding of their properties. Furthermore, it is imperative that we validate the information provided by manufacturers regarding these archwires through independent studies. This review evaluates existing studies on the subject with a specific focus on the Bio-active multi-force NiTi archwire, by examining its mechanical, thermal, and physicochemical properties before and after clinical use. This archwire consists primarily of Ni and Ti, with traces of Fe and Cr, which release graduated, biologically tolerable forces which increase in a front-to-back direction and are affected by the temperature of the environment they are in. The review provides information to practicing orthodontists, facilitating informed decisions regarding the selection and use of Bio-active™ archwires for individual patient treatments.

Observation of Hydrostatic‐Pressure‐Modulated Giant Caloric Effect and Electronic Topological Transition

AbstractPhase transition is a fundamental phenomenon in condensed matter physics, in which states of matter transform to each other with various critical behaviors under different conditions. The magnetic martensitic transformation features significant multi‐caloric effects that benefit the solid‐state cooling or heat pumping. Meanwhile, the electronic topological transition (ETT) driven by pressure has been rarely reported in martensitic systems. Here, the modulation effects of hydrostatic pressure on phase transitions in a magnetic martensitic alloy are reported. Owing to the huge volume expansion during the transition, the martensitic transition temperature is driven from 339 to 273 K by pressure within 1 GPa, resulting in highly tunable giant baro‐ and magneto‐caloric effects (BCE and MCE) in a wide working temperature range. Interestingly, an ETT is further induced by pressure in the martensite phase, with a sudden drop of the measured saturation magnetization around 0.6 GPa. First‐principles calculations reveal a sharp change in the density of states (DOS) due to the orbit shift around the Fermi level at the same pressure and reproduce the experimental observation of magnetization. Besides, the ETT is accompanied by remarkable changes in the lattice parameters and the unit‐cell orthorhombicity. The study provides insight into pressure‐modulated exotic phase‐transition phenomena in magnetic martensitic systems.

In depth analysis of the passive film on martensitic tool alloy: Effect of tempering temperature

Effect of tempering temperature on the composition of the passive film of a martensitic tool alloy was studied by synchrotron-based hard/soft X-ray photoelectron spectroscopy and electrochemical analyses. The contents of Cr and Mo in the passive film are affected by precipitation of tempering carbides. Increase of tempering temperature from 200 to 525°C leads to enhanced formation of Cr/Mo-rich tempering carbides and Cr depletion. Tempering at 525°C results in a Cr content < 11 at% in the underlying metallic layer and formation of a Cr-deficient defective passive film, and thus loss of passivity for the tool alloy in corrosive conditions.

An analytical study on SMA beam-column actuators for anti-buckling phenomenon

The present paper focuses on studying the anti-buckling behavior of prismatic martensitic shape memory alloy (SMA) beam-columns. It combines analytical and semi-analytical approaches to investigate the process of column straightening for anti-buckling. We try to comprehensively describe this phenomenon and develop a mathematical model to formulate each step of the anti-buckling problem. Due to the complex stress–strain behavior of SMA material, nine different stages of stress-height diagrams may potentially occur during this effect; thus, for facilitating the design process of SMA structures, corresponding forces and moments to each stage, are analytically derived. Our demonstration establishes that the primary cause of beam-column straightening is not the uniformity of stress, but rather the achievement of uniform strain across all fibers of the cross-section. This uniform strain distribution implies that the curvature of the beam-column diminishes to zero.

Characterization of hot workability of a Cu containing high strength low alloy steel using processing map

Hot workability of an experimental Cu containing martensitic high strength low alloy (HSLA) steel was characterized by conducting isothermal hot compression tests at different temperatures (900–1100 °C) and strain rates (0.0003–1 s−1). Flow curves exhibits predominantly single peak behaviour at temperatures for a strain rate > 0.01 s−1. At temperature > 950 °C and for low strain rates of 0.0003 and/or 0.001 s−1, multiple peaks characterised by oscillations in flow stress was observed. The strain rate sensitivity (m), temperature sensitivity (S) of the material was calculated and the processing map was developed to identify optimum condition for thermo-mechanical processing. The material exhibits three suitable processing windows in temperature – strain rate space viz., (1) 1050–1100 °C; 0.1–0.01 s−1 (2) 980–1020 °C; 0.1–1 s−1 and (3) 980–1020 °C; 0.001–0.0003 s−1. The microstructure of the material deformed under all the above mentioned processing conditions exhibited defect free equiaxed dynamically recrystallized grains with an average grain size of 30–40 μm. Any or combination of these processing conditions can be used by the industry for designing suitable forging process (roughing, finishing etc.) based on the infrastructure available. Further, using Avrami approach, the effect of strain, strain rate and temperature on the kinetics of dynamic recrystallization (DRX) was also evaluated. The results obtained are presented and discussed.

Improvement of shape recovery by controlling the microstructure and mechanical properties in a thermomechanically-treated Fe-based alloy

In this research, the effects of thermomechanical treatment including heavy cold rolling and post-deformation annealing on the improvement of shape recovery in an Fe–9Ni–7Mn (at.%) martensitic alloy were investigated. Experimental results showed that the 80 % cold rolling produced a little fraction of strain-induced austenite phase in the martensitic matrix due to the strain concentration in the microstructure and the temperature rise under deformation. During post-deformation annealing at 590 °C in a dual phase (α+γ) region, a greater fraction of the austenite was introduced in the martensitic matrix such that its amount first increased by increasing the annealing time to 1.8 ks and then decreased at a more time of reversion. The microstructural evolution revealed that the austenite reversion under post-deformation annealing initially occurred by a shear nature at the early steps of reversion and then continued by diffusion. Tensile testing represented a good mixture of a relatively high ultimate tensile strength of ∼780 MPa and proper ductility of ∼8.5 % in the post-deformation annealed (PDA) sample for 0.9 ks. In addition, the shape memory properties were examined under the conditions of cold rolling and post-deformation annealing. The results showed a maximum shape recovery rate of ∼23 % for the cold rolled specimen which increased to ∼50 % after post-deformation annealing for 0.9 ks. The presence of a relatively high amount of retained austenite with proper stability and strength in the microstructure of the PDA sample for 0.9 ks was the reason for achieving the highest value of shape recovery.

Self-centering capacity of RC columns reinforced by martensitic NiTi SMA bars in plastic hinge region

This study aimed to assess self-centering in reinforced concrete (RC) columns incorporating martensitic shape memory alloy (SMA) bars within the plastic hinge region. Three RC columns were prepared: one conventional, the others with SMA bars in the hinge zone. Columns, 400 mm in diameter and 1400 mm in height, with an aspect ratio of 3.5, were used. SMA bars, 400 mm long, were connected to steel rebars with specialized couplers. Through cyclic lateral loading, lateral displacements and corresponding forces were measured. Strain in the SMA bars was also recorded. The RC column with SMA bars displayed a plastic hinge near the couplers, concentrating concrete damage at this location, a departure from the conventional column failure mode. SMA bars remained elastic, while steel rebars yielded within the couplers. The RC column with SMA bars demonstrated exceptional self-centering, recovering about 95% at a 5% drift. However, its energy dissipation capacity was lower than the conventional RC column. The equivalent damping ratio for the RC column with SMA bars stabilized at approximately 3% after a 1.75% drift. This suggests that the remarkable self-centering capacity in the RC column with SMA bars was primarily due to the elastic behavior of the martensitic SMA bars.

Hyflex CM and EDM from Shape Memory to Control Memory.

The new era in endodontics has been established with the introduction of nickel titanium (NiTi) alloys, and later on the automation of mechanical preparation. By changing the phase transformation temperatures of NiTi alloy, the manufacturers alter the phase composition to have a NiTi with new mechanical properties. These mechanical properties can be achieved either by thermal, mechanical treatments or both. Moreover, many machining procedures (e.g. twisting, electrical discharge machining), were developed. The higher flexibility of thermomechanically treated NiTi alloys was found as the main advantages of these alloys with the improvement of cyclic fatigue resistance when compared to conventional NiTi. Austenitic alloys have superelastic properties due to stress-induced martensite transformation and consequently try to springback to their original shape after distortion. In contrast, the martensitic instruments have ability to reorientation of martensite variants when heated. So these instruments easily deformed and show a shape memory effect. Moreover, the use of martensitic alloy results in more flexible files, with an increased cyclic fatigue resistance compared with austenitic alloy. So, continued development in the manufacturing treatment of NiTi alloys has resulted in the producing of controlled memory (CM) wire. These materials do not possess superelastic properties at neither room nor body temperature. This article reviews the development process, features and properties of Hyflex file and Hyflex EDM file made from CM wire. Keywords: NiTi alloy, CM wire, Hyflex EDM, Heat treated NiTi

EBSD study of variant reorientation, texture, and twin formation in a martensitic NiTi alloy deformed in compression

Martensitic crystallography plays a vital role in the texture evolution and mechanical properties in Nickel-Titanium (NiTi) shape memory alloys when subjected to deformation. However, their microstructural changes during deformation are not well known and understood. In this study, we systematically investigate the stress-induced change of the microstructure of NiTi shape memory alloy under compression using the electron backscattered diffraction (EBSD) technique, and more specifically the variant reorientation, the evolution of textures, and the formation of twins. The EBSD maps reveal that upon strain the martensite morphologies shift from needle to block and their orientations are strongly reinforced along the loading axis. To quantify these microstructural changes, we used the Interaction Work (IW) associated with the lattice distortion of single variant, which provides a good fit with the experimental observation. A strong dependence of reorientation on the pre-textures of the parent B2 grains was also put in evidence. Other plasticity sources were confirmed such as dislocations and deformation twins. The calculations indicate that, for some specific orientations of parent grains, the active deformation twins could be easier for {011}M twin than that of (201¯)M deformation twin, whereas other orientations only favor the (201¯)M deformation twin.

Study of the effect of multiple phase transformations and relaxation annealing on the microstructure of a martensitic TiNi alloy in different structural states

The work was devoted to studying the effect of multiple phase transformations in the temperature range of phase transformations of a TiNi alloy with a martensitic structure in various initial states - coarse-grained, ultrafine-grained, nanostructured. The conducted studies have shown that in the process of thermal cycling, the accumulation of defects in the crystalline structure occurs - dislocations, which contribute to a decrease in the size of structural elements. Subsequent relaxation annealing, slightly reducing the dislocation density, made it possible to obtain a stable and more equilibrium microstructure, including the nanostructural state.

Tempered Hardness Optimization of Martensitic Alloy Steels

Tempered Hardness Optimization of Martensitic Alloy Steels

Self-centering capacity of RC columns with smart plastic hinges of martensitic NiTi SMA bars

The objective of this study was to examine the self-centering capacity of reinforced concrete (RC) columns with martensitic shape memory alloy (SMA) bars in the plastic hinge region. To achieve this, three RC columns were prepared: one was conventional and the other two had SMA bars in the plastic hinge zone. The columns had a diameter of 400 mm, height of 1400 mm, and aspect ratio of 3.5. The 400 mm long SMA bars were connected to the steel rebars using specially devised couplers. A cyclic lateral load was applied at the top of the columns, and the lateral displacements along the height of the columns and the corresponding forces were measured during cyclic lateral loading. The strain in the SMA bars was also measured. The RC column with SMA bars exhibited a plastic hinge around the couplers, thus concrete damage from cracking was concentrated at this site. This was completely different from the failure mode of the conventional RC column. The SMA bars in the column were in an elastic state, whereas the steel rebars yielded inside the couplers. The RC column with SMA bars exhibited excellent self-centering capacity, and its displacement recovery ratio was approximately 95% at a drift of 5%. However, its energy-dissipation capacity was lower than that of the conventional RC column. The equivalent damping ratio of the RC column with SMA bars was approximately 3% after 1.75% drift. It is conjectured that the excellent self-centering of the RC column with SMA bars was caused by the elastic behavior of the martensitic SMA bars.

Apical Transportation of Apical Foramen by Different NiTi Alloy Systems: A Systematic Review

Endodontic shaping can lead to canal and apical anatomical alterations, which may compromise the outcome of root canal treatment. The objective of this systematic literature review is to assess whether the use of martensitic endodontic instruments can result in less apical transportation compared to austenitic instruments during endodontic therapy. A search was conducted on PubMed, Ovid MEDLINE, and the Web of Science. The inclusion criteria were in vitro studies comparing apical transportation using endodontic instruments with austenitic or martensitic alloys. The search of the scientific databases yielded 592 results, of which only 10 were eligible for evaluation after screening. Based on the analysis of the selected articles, it can be concluded that martensitic endodontic instruments result in less apical transportation compared to austenitic instruments during the shaping phase of endodontic treatment. This behavior can be attributed to the increased flexibility of martensitic instruments. Further research is warranted to further explore this topic and provide additional evidence supporting the use of martensitic instruments in clinical practice.

Comparative analysis of process-induced strain glass states in austenitic and martensitic NiTi shape memory alloy plates

Strain glass alloys (SGAs) are metallic alloys with glassy martensitic nanodomains within a crystalline material that occur from compositionally or processing-induced strain. SGAs originate from shape memory alloys (SMAs) and exhibit similar shape memory properties and high actuation densities. The transition from SMA to SGA is relatively unexplored, and although there are similarities to amorphous SMAs and cold-worked SMAs, SGAs should be distinguished as a separate grouping. The transition occurs by interrupting the long-range martensitic order, which in turn disrupts the martensitic transformation, resulting in short-range martensitic order. A glassy martensitic phase is produced that exhibits enhanced structural and load-bearing abilities, functional stresses, and recoverability. In this study, the transformation from SMA to SGA is explored in two common commercially available SMAs, Ni49.5Ti50.5 and Ni50.8Ti49.2 (at. %), to compare martensitic versus austenitic SGAs, respectively. SMA plates were cold worked in 5% increments until a strain glass transition occurred. Characterizations of the samples at various stages of cold work were examined via differential scanning calorimetry (DSC), Vickers hardness, transmission electron microscopy (TEM), and synchrotron radiation X-ray diffraction (SR-XRD). Some prominent characteristics between the two plates, such as enthalpy peaks, twin size reduction, and crystallographic structure, were examined and compared to improve the understanding of the SMA to SGA transition.

Disorder enhanced dynamical heterogeneity in strain glass alloys.

An open question related to strain-glass (STG) alloys is whether they process similar dynamical behaviors to other glass systems. In the present work, we investigate the reorientation process of martensite domains in both STG and martensitic alloys. Our results show the presence of highly doped point defects can greatly intensify the dynamical heterogeneity and spatiotemporal correlation in ferroelastic or shape memory alloy systems, which are also two main hallmarks of structural glasses. What's more, we find that such dynamic heterogeneity exists in a different range spanning microscopic to mesoscopic scales, indicated by our molecular dynamic (MD) simulations and time-dependent Ginzburg-Landau (TDGL) modeling. Dopant atoms induced transient strain networks, i.e., spatial correlated local lattice distortion, is a response for such heterogeneous dynamics. The present study thus solidifies strain glass as a new state of matter and may provide guidelines for developing new strain glass alloys.&#xD.

Role of Zr and thermomechanical treatment on phase transformation and functional properties of NiTi-based shape memory alloys

A systematic investigation was conducted to evaluate the role of Zr addition on the martensitic phase transformation behavior and properties of NiTi-based shape memory alloys. Equiatomic binary NiTi alloy and ternary Ni50Ti45Zr5 and Ni50Ti40Zr10 alloys (at.%) were processed by a simple thermomechanical treatment including cold rolling followed by post-deformation annealing at 450 °C for 30 and 60 min. The microstructural investigation and thermal analyses reveal that martensitic phase transformation is suppressed by adding Zr. Solid solution strengthening due to Zr addition, strain hardening due to cold rolling and formation of (Ti,Zr)2Ni precipitates in a dual-phase microstructure during annealing leads to a significant increase in hardness in the thermomechanically treated alloys (e.g., up to 550 Hv for Ni50Ti45Zr5 alloy). The stress-strain curve of martensitic Ni50Ti50 alloy reveals the essential characteristics of shape memory effect, however, Ni50Ti45Zr5 alloy shows typical features of pseudoelasticity with significantly high stress plateau (∼600 MPa) and remarkable recovered strain of 3.5% during unloading.