Magnetic Interface Research Articles

Manipulating Interface Magnetism in Manganite Thin Film Membranes by Substrate Surface Chemistry

Manipulating Interface Magnetism in Manganite Thin Film Membranes by Substrate Surface Chemistry

Magnetic actuator driver system for laser scanning capsule endoscopy

This paper focuses on designing and implementing a power and area-efficient magnetic actuator driver interface integrated circuit for laser scanning capsule endoscopy. The proposed system contains a 3D-printed focus-adjusting actuator embarking a lens, multiple magnets, an external coil, battery, laser, and actuator driver integrated circuit with off-chip components. The actuator features multiple pantograph springs connected to the lens, as well as multiple magnets, enabling precise focusing capability through electromagnetic actuation. A magnetic actuator driver integrated circuit implemented in a commercial 180 nm CMOS process drives the coil at 32 Hz, which is the mechanical resonance frequency of the actuator. A novel control methodology for the driver has been devised, aimed at enhancing driving efficiency and mitigating total harmonic distortion. Simulations and measurements substantiate that the actuator can induce a 3.22 mm focal point displacement while the driver circuit delivers 9.62 mA (RMS) current to the 7.7 mH coil. Under these conditions, the system exhibits an aggregate power consumption of 11.48 mW, thereby achieving a power efficiency of 85.5%.

Role of the magnetic layer interface, roughness, and thickness in the temperature-dependent magnetic properties of Al2O3/Co/CoO thin films deposited by magnetron sputtering

Using the methods of atomic force and electron microscopy and the magneto-optical Kerr effect, the role of the interface, roughness, and thickness of the magnetic layer in the temperature-dependent magnetic properties of thin Al2O3–Co films with a naturally oxidized cobalt surface was studied. The layers were deposited by magnetron sputtering. The thickness of the cobalt layer varied from 2 to 100 nm. For the first time, the dependences of coercive forces and exchange displacements on the thickness of the cobalt film in the temperature range from 80 to 300 K were obtained and analyzed. The contribution to the coercive force and exchange displacement from the oxidized cobalt surface increases as the temperature decreases below 160 K. The magnitude of the contribution depends on the base material on which the cobalt film is deposited and is maximum for a cobalt film with a thickness of ∼20 nm in the Al2O3/Co structure. A weakly magnetic layer was found at the Al2O3/Co interface. The behavior of the exchange bias in this layer is similar to the behavior of a ferromagnetic Co core with a naturally oxidized CoO shell. The thickness of this layer depends on the speed and order of deposition of the layers. When the order of deposition of layers (Co/Al2O3) changes, the behavior of the exchange displacement of the interface becomes similar to that observed in the ferromagnet/antiferromagnet system. That is, when the deposition order changes, the value of the exchange shift changes sign when the cobalt layer thickness is below 10 nm.

In-situ chemically synthesized Fe3O4/K-geopolymer composite with microwave absorbency for additive manufacturing

In this work, we utilized an in-situ chemical synthesis method to fabricate a Fe3O4/K-geopolymer (KGP) composite to be applied in a microwave absorbent field. This material, as a type of ceramic precursor, is highly expected to be a 3D printing material to prepare microwave absorbing components with complex shapes. The investigation results demonstrate that the material possesses a large effective microwave absorbing bandwidth of 3.7 GHz with the minimum reflection loss reducing to −12.2 dB when the generated Fe3O4 percent reaches 12 wt% in the KGP composite. This microwave absorbent performance can be attributed to a synergistic effect between the eddy current loss caused by the improved electrical conductivity of magnetic nanoparticles and the interfacial polarization effect from the geopolymer matrix and magnetic medium interface. Also, we used direct ink writing technology to print two-dimensional components with desirable patterns. Thickness-dependent wave absorption evaluation results confirmed a maximum reflection loss of −25.9 dB at 15.2 Hz was obtained from the printed sample containing 9.0 wt% Fe3O4 for a layer thickness of 10 mm, indicating that wave consumption effectiveness was determined by porous microstructures, magnetic loss of Fe3O4 nanoparticles as well as suitable impedance matching. The preparation method and synthesized material pave the way for integrated manufacturing of 3D printing components with microwave absorbing performance.

A novel “S” chain structure mechanism model of magneto-rheological elastomer

Mechanism models based on chain-like structures are often used to characterize the morphology of magneto-rheological elastomer (MRE) and provide theoretical guidance for MRE preparation. However, widely used shear and tension mechanism models based on oblique straight chain or bent-chain structures have the limitation of insufficient accuracy in characterization, mainly because the internal particle chains of anisotropic MRE are not simple oblique straight or bent from scanning electron microscope (SEM) results. Therefore, the particle chain formation and particle interaction mechanism within MRE are revealed firstly. The theoretical results shows that particles tend to form S-like chain structures due to complex attraction and extrusion. On this basis, a novel “S” chain mechanism model is proposed, which is confirmed to have higher accuracy than the ideal shear model and tension model by comparing with the experimental results. The main reason is that the “S” chain mechanism model has realized the unification of shear, compressive, or tension mode, and integrates the fully coupled magnetic field, distribution parameters and interface stretching. The “S” chain mechanism model also takes into account the radius and volume fraction of the particles in MRE preparation, which makes it a more accurate guide to subsequent preparation.

Modulation of Kondo Behavior in a Two-Dimensional Epitaxial Bilayer Bi(111)/Fe3GeTe2 Moiré Heterostructure.

Artificial two-dimensional (2D) moiré superlattices provide a platform for generating exotic quantum matter or phenomena. Here, an epitaxial heterostructure composed of bilayer Bi(111) and an Fe3GeTe2 substrate with a zero-twist angle is acquired by molecular beam epitaxy. Scanning tunneling microscopy and spectroscopy studies reveal the spatially tailored Kondo resonance and interfacial magnetism within this moiré superlattice. Combined with first-principles calculations, it is found that the modulation effect of the moiré superlattice originates from the interfacial orbital hybridization between Bi and Fe atoms. Our work provides a tunable platform for strong electron correlation studies to explore 2D artificial heavy Fermion systems and interface magnetism.

Emergence of Interfacial Magnetism in Strongly-Correlated Nickelate-Titanate Superlattices.

Strongly-correlated transition-metal oxides are widely known for their various exotic phenomena. This is exemplified by rare-earth nickelates such as LaNiO3, which possess intimate interconnections between their electronic, spin, and lattice degrees of freedom. Their properties can be further enhanced by pairing them in hybrid heterostructures, which can lead to hidden phases and emergent phenomena. An important example is the LaNiO3/LaTiO3 superlattice, where an interlayer electron transfer has been observed from LaTiO3 into LaNiO3 leading to a high-spin state. However, macroscopic emergence of magnetic order associated with this high-spin state has so far not been observed. Here, by using muon spin rotation, x-ray absorption, and resonant inelastic x-ray scattering, direct evidence of an emergent antiferromagnetic order with high magnon energy and exchange interactions at the LaNiO3/LaTiO3 interface is presented. As the magnetism is purely interfacial, a single LaNiO3/LaTiO3 interface can essentially behave as an atomically thin strongly-correlated quasi-2D antiferromagnet, potentially allowing its technological utilization in advanced spintronic devices. Furthermore, its strong quasi-2D magnetic correlations, orbitally-polarized planar ligand holes, and layered superlattice design make its electronic, magnetic, and lattice configurations resemble the precursor states of superconducting cuprates and nickelates, but with an S→1 spin state instead.

First-principles study of the structure, magnetism, and electronic properties of the all-Heusler alloy Co2MnGe/CoTiMnGe(100) heterojunction.

Based on first-principles calculations in the density functional theory, we systematically investigated the possible interface structure, magnetism, and electronic properties of the all-Heusler alloy Co2MnGe/CoTiMnGe(100) heterojunction. The calculation indicated that the Co2MnGe Heusler alloy is a half-metal with a magnetic moment of 4.97μB. CoTiMnGe is a narrow-band gap semiconductor and may act as an ultra-sensitive photocatalyst. We cannot find an "ideal" spin-polarization of 100% in CoCo termination and MnGe termination. Due to the interface interaction, the direct magnetic hybridization or indirect RKKY exchange will be weakened, leading to an increase in the atomic magnetic moment of the interfacial layer. For eight possible heterojunction structures, the half-metallic gaps in the Co2MnGe bulk have been destroyed by the inevitable interface states. The spin-polarization value of 94.31% in the CoCo-TiGe-B heterojunction revealed that it is the most stable structure. It is feasible to search for high-performance magnetic tunnel junction by artificially constructing suitable all-Heusler alloy heterojunctions.

Porous carbon composite nanosheets loaded with magnetic FeNi/NiFe2O4 and dielectric SiO2 nanoparticles for adjustable microwave absorption

According to the escalating concern regarding the health hazards associated with electromagnetic radiation, the significance of absorbing materials underscores which could mitigate the healthy risks. While magnetic materials offer excellent absorption performance, their high density poses challenges to achieving optimal absorption efficiency. Conversely, carbon-based materials are known for their lightweight and versatile but face impedance matching issues. To address these obstacles, carbon/magnetic composite materials have been explored. However, their absorption performance has not fully met requirements due to weaker magnetic properties and increased density. Herein, we synthesized a porous carbon material embedded with magnetic FeNi/NiFe2O4 and dielectric SiO2 nanoparticles (FeNi-NiFe2O4-SiO2@PC) using carbonthermal method. By adjusting the ratio of polyvinylpyrrolidone to nitrates, the electromagnetic wave (EMW) absorption performance is adjusted. The FeNi-NiFe2O4-SiO2@PC composites display remarkable EMW absorption properties, achieving a minimum reflection loss of −69.9 dB at a thin thickness of 1.495 mm and a maximum effective absorption bandwidth of 5.68 GHz, covering the range from 12.32 to 18.0 GHz at a thickness of 1.92 mm. This outstanding performance can be attributed to the favorable impedance matching and the three-dimensional porous structure, which facilitates a 3D transmission network for multiple reflections. Additionally, the presence of FeNi, NiFe2O4, and SiO2 nanoparticles enhances magnetic loss, conductive loss, interface polarization, and dipolar polarization, leading to excellent ab. Hence, this work offers insights into the composition design of high-performance absorbing materials.

Early‐Precambrian crystalline basement beneath the Upper Yangtze Block from regional aeromagnetic anomalies: Depth from extreme points approach

AbstractAlthough the early‐Precambrian crystalline basement is now only sporadically exposed in the northern and south‐western parts of the Yangtze Block, it is supposed to have a widespread distribution beneath its Neoproterozoic and Phanerozoic covers. Here we present results of regional aeromagnetic data processing in consideration of remanent magnetization to investigate the spatial distribution of the early‐Precambrian basement buried deep under the Upper Yangtze Block and surrounding areas. The direct analytic signal amplitude of the aeromagnetic anomalies, which is less affected by the magnetization direction, reveals a broader basement below the Sichuan Basin, extending far north to the Micang Mountain. A comparison between the direct analytic signal amplitude with the reduction to the pole aeromagnetic anomalies indicates that possible remanent magnetization exists beneath the Micang Mountain near the boundary between the Qinling Orogen and Sichuan Basin. The automatic depth from extreme points transform is then performed on the direct analytic signal amplitude to estimate the depth to the early‐Precambrian crystalline basement. A synthetic model of a magnetic interface with remanent magnetization and random noise shows that the depth from extreme points method is able to resolve variable basement depths. Application of the depth from extreme points method to the direct analytic signal amplitude of the Upper Yangtze Block presents meaningful results about the early‐Precambrian crystalline basement undulations. It is shallow and uplifted beneath the Sichuan Basin, extending north to the Qinling‐Dabie Orogen, probably corresponding to the ancient Chuanzhong palaeo‐uplift. Although it gradually deepens to the east, the deepest basement is buried under the Jiangnan Orogen, which is likely associated with the collision‐induced crustal thickening between the Yangtze and Cathaysia blocks during the assembly of the Columbia supercontinent. Large gas fields around the Sichuan Basin are found at the slopes or depressions between basement uplifts, indicating that the deep marine carbonate rocks in the south and east of Sichuan Basin, particularly those located at the slopes or depressions between ancient basement uplifts, are favourable targets for further petroleum exploration.

Recovering 3D Basin Basement Relief Using High‐Precision Magnetic Data Through Random Forest Regression Algorithm: A Case Study of Tianzhen‐Yanggao Sag in Datong Basin

AbstractInversion of magnetic basement interfaces in basins is essential for interpreting potential field data and studying geothermal resource distribution, as well as basin formation and evolution. This paper introduces a novel method for inverting magnetic basement interfaces using a random forest regression (RFR) algorithm that combines potential field processing and machine learning techniques. The method creates magnetic base interface models and corresponding magnetic anomaly data through the random midpoint displacement method and magnetic interface finite element forward simulation. These anomalies are then processed using techniques such as directional transformations, analytical continuation, spatial derivatives, and fractional transformations. Feature attributes are extracted, and Gini importance is utilized to measure the contributions of feature factors, identify effective features, and enhance algorithm efficiency. The validity and practicality of the method are demonstrated through the analysis of both idealized and noisy models. The proposed machine learning‐based approach is more intelligent, efficient, and accurately represents the relief of magnetic base interfaces. When applied to magnetic survey data in the Datong Basin, it produced a reliable basin base model that aligns with known structural information, paving the way for further research in magnetic interface inversion.

One-Dimensional Magnetic Conduction Channels across Zigzag Graphene Nanoribbon/Hexagonal Boron Nitride Heterojunctions.

We examine the electronic structure of recently fabricated in-plane heterojunctions of zigzag graphene nanoribbons embedded in hexagonal boron nitride. We focus on hitherto unexplored interface configurations in which both edges of the nanoribbon are bonded to the same chemical species, either boron or nitrogen atoms. Using ab initio and mean-field Hubbard model calculations, we reveal the emergence of one-dimensional magnetic conducting channels at these interfaces. These channels originate from the energy shift of the magnetic interface states that is induced by charge transfer between the nanoribbon and hexagonal boron nitride. We further address the response of these heterojunctions to external electric and magnetic fields, demonstrating the tunability of energy and spin splittings in the electronic structure. Our findings establish that zigzag graphene nanoribbon/hexagonal boron nitride heterojunctions are a suitable platform for exploring and engineering spin transport in the atomically thin limit, with potential applications in integrated spintronic devices.

Electrical Control Grain Dimensionality with Multilevel Magnetic Anisotropy.

In alignment with the increasing demand for larger storage capacity and longer data retention, the electrical control of magnetic anisotropy has been a research focus in the realm of spintronics. Typically, magnetic anisotropy is determined by grain dimensionality, which is set during the fabrication of magnetic thin films. Despite the intrinsic correlation between magnetic anisotropy and grain dimensionality, there is a lack of experimental evidence for electrically controlling grain dimensionality, thereby impairing the efficiency of magnetic anisotropy modulation. Here, we demonstrate an electric field control of grain dimensionality and prove it as the active mechanism for tuning interfacial magnetism. The reduction in grain dimensionality is associated with a transition from ferromagnetic to superparamagnetic behavior. We achieve a nonvolatile and reversible modulation of the coercivity in both the ferromagnetic and superparamagnetic regimes. Subsequent electrical and elemental analysis confirms the variation in grain dimensionality upon the application of gate voltages, revealing a transition from a multidomain to a single-domain state, accompanied by a reduction in grain dimensionality. Furthermore, we exploit the influence of grain dimensionality on domain wall motion, extending its applicability to multilevel magnetic memory and synaptic devices. Our results provide a strategy for tuning interfacial magnetism through grain size engineering for advancements in high-performance spintronics.

Ionic control of magnetism in all-solid-state CoOx/yttria-stabilized zirconia heterostructures

Magneto-ionic gating, a procedure that enables the modulation of materials' magnetic properties by voltage-driven ion motion, offers alternative perspectives for emerging low-power magnetic storage and spintronic applications. Most previous studies in all-solid-state magneto-ionic systems have focused on the control of interfacial magnetism of ultrathin (i.e., 1–3 nm) magnetic films, taking advantage of an adjacent ionic conducting oxide, usually GdOx or HfOx, that transports functional ionic species (e.g., H+ or O2−). Here, we report on room-temperature OFF–ON ferromagnetism by solid-state magneto-ionics in relatively thick (25 nm) patterned CoOx films grown on an yttria-stabilized zirconia (YSZ) layer, which acts as a dielectric to hold electric field and as an O2− ion reservoir. Upon negatively biasing, O2− ions from the CoOx tend to migrate toward the YSZ gate electrode, leading to the gradual generation of magnetization (i.e., OFF-to-ON switching of a ferromagnetic state). X-ray absorption and magnetic circular dichroism studies reveal subtle changes in the electronic/chemical characteristics, responsible for the induced magnetoelectric effects in such all-oxide heterostructures. Recovery of the initial (virtually non-magnetic) state is achieved by application of a positive voltage. The study may guide future development of all-solid-state low-power CMOS-compatible magneto-ionic devices.

Research on modeling and self-excited vibration mechanism in magnetic levitation-collision interface coupling system

Research on modeling and self-excited vibration mechanism in magnetic levitation-collision interface coupling system

Highly Robust Room-Temperature Interfacial Ferromagnetism in Ultrathin Co2Si Nanoplates.

The reduced dimensionality and interfacial effects in magnetic nanostructures open the feasibility to tailor magnetic ordering. Here, we report the synthesis of ultrathin metallic Co2Si nanoplates with a total thickness that is tunable to 2.2 nm. The interfacial magnetism coupled with the highly anisotropic nanoplate geometry leads to strong perpendicular magnetic anisotropy and robust hard ferromagnetism at room temperature, with a Curie temperature (TC) exceeding 950 K and a coercive field (HC) > 4.0 T at 3 K and 8750 Oe at 300 K. Theoretical calculations suggest that ferromagnetism originates from symmetry breaking and undercoordinated Co atoms at the Co2Si and SiO2 interface. With protection by the self-limiting intrinsic oxide, the interfacial ferromagnetism of the Co2Si nanoplates exhibits excellent environmental stability. The controllable growth of ambient stable Co2Si nanoplates as 2D hard ferromagnets could open exciting opportunities for fundamental studies and applications in Si-based spintronic devices.

Effect of metal insertion on the magnetic properties and anomalous Hall effect in MgO/CoFeB/Ta/MgO films

CoFeB-based nano-magnetic multilayers can be applied in magnetic sensors, magnetic random access memory and other logic devices, which have attracted wide attention. The magnetic properties and interface structure of the magnetic multilayers still need further research for future applications. The effects of Pt insertion on the perpendicular magnetic anisotropy (PMA) and the anomalous Hall effect (AHE) of MgO/CoFeB/Pt/Ta/MgO multilayers were studied. It is found that the sample with 0.2 nm Pt insertion at the CoFeB/Ta interface and annealed at 250 °C can transform the films from in-plane magnetic anisotropy to PMA. The effective magnetic anisotropy K eff can reach 1.82 × 106 erg cm−3. The Pt insertion and annealing heat treatment can promote the migration of oxygen from MgO at the top layer to CoFeB/Ta interface and combine with Fe to generate iron oxide, and improve the orbital hybridization of Fe 3d and O 2p, thus successfully inducing the PMA of the film samples. In addition, Pt insertion and annealing treatment can improve the side-jump mechanism and the skew scattering mechanism which contribute to the AHE. This work provides guidance for the application of PMA materials in magnetic sensor and memory devices.

Multi-channel magnetic resonance spectroscopy graphical user interface (McMRSGUI).

This work introduces an open-sourced graphical user interface (GUI) software enabling the combination of multi-channel magnetic resonance spectroscopy data with different literature-based methods for the improvement of the quality and reliability of combined spectra. The multi-channel magnetic resonance spectroscopy graphical user interface (McMRSGUI) is a MATLAB-based spectroscopy processing GUI equipped to load multi-channel MRS data, pre-process, combine, and export combined data for evaluation with open-source quantification software (jMRUI). A literature-based, decision-tree process was incorporated into the combination type selection to serve as a guide to minimize spectral distortion in selecting between weighting methods. Multi-channel, simulated spectra were combined with the different combination techniques and evaluated for spectral distortion to validate the code. The incorporation of the combination methods into a single processing software enables multi-channel magnetic resonance spectroscopy (MRS) data to be combined and compared for improved spectral quality with little user knowledge of combination techniques. Through the spectral peak distortion simulation of the combination methods, combined signal-to-noise ratio (SNR) values from the literature were verified. The spectral peak distortion simulation provides a secondary tool for researchers to estimate the spectral SNR levels when spectral distortion could occur and use this knowledge to further guide the selection of their combination technique. The McMRSGUI provides a software toolkit for evaluating multi-channel MRS data and their combination. Simulations evaluating spectral distortion at different noise levels were performed for each combination method to validate the GUI and demonstrate a method for researchers to assess the combined SNR levels at which they could be introducing spectral distortion.

Magnetic exchange coupling via constructing hard/soft magnetic interface for stable microwave absorption

Magnetic exchange coupling interaction at hard/soft magnetic interface can expand the frequency range of magnetic resonance, providing the stable microwave absorption performance that is insensitive to matching thickness. A novel nanocomposite, in which shell/core structured Sm2Co17/Co(Sm) hard/soft magnetic nanoparticles are embedded into Sm2O3-doped porous carbon, is prepared. The magnetic exchange coupling between hard magnetic Sm2Co17 shell and soft magnetic Co(Sm) core results in extending resonance frequency. Due to the synergistic effect of quarter-wavelength cancellation and electromagnetic loss, the nanocomposites deliver the optimal reflection loss (RLm) of −38.87 dB and effective absorption bandwidth (EAB) of 3.36 GHz at thickness of 2.5 mm and 2.7 mm, respectively, and stable microwave absorption performances (RLm ≤ -20 dB and EAB ≥ 3.0 GHz) in thickness of 2.4–3.0 mm.

LaAlO3/SrTiO3 Heterointerface: 20 Years and Beyond

AbstractThis year marks the 20th anniversary of the discovery of LaAlO3/SrTiO3 (LAO/STO) oxide heterointerfaces. Since their discovery, transition metal oxide (TMO) interfaces have emerged as a fascinating and fast‐growing area of research, offering a variety of unique and exotic physical properties which has provided a strong impetus for the rapid advances and actualization of oxide electronics. This review revisits the fundamental mechanisms accounting for the two‐dimensional (2D) conducting interfaces, and how new models proposed to better account for the unique interfacial effects. Recent breakthroughs in the theoretical and experimental domains of oxide interfaces are also discussed including the detection and investigation of 2D quasiparticle. Moving beyond the well‐known LAO/STO interface, this review delves into other systems where unconventional interfacial superconductivity, interfacial magnetism, and spin polarization are dealt with in greater detail. In terms of device applications, this review proceeds with a treatment on the recent developments in domains including field effect transistors and freestanding heterostructure membranes. By emphasizing the opportunities and challenges of integrating oxide interfaces with existing technologies, the review will end off with an outlook projecting the progress and the trajectory of this research domain in the years to come.