Low-temperature Solution-processed SnO2 Research Articles

Ni-Doped SnO2 as an Electron Transport Layer by a Low-Temperature Process in Planar Perovskite Solar Cells.

Perovskite solar cells (PSCs) based on a planar structure have recently become more attractive due to their simple manufacturing process and relatively low cost, while most perovskite solar cells employ highly porous TiO2 as an electron transport layer in mesoporous devices offering higher energy conversion efficiency (PCE). In planar structural devices, non-radiative recombination effects of the absorber layer and the electron transport layer cause potential loss and lower PCE. We created an efficient electron transport layer by combining low-temperature Ni-doped SnO2 with SDBS as a surfactant (denoted as Ni:SnO2). Doping Ni+ into low-temperature solution-processed SnO2 increased the power conversion efficiency of PSCs from 17.8 to 19.7%.

Dependence of Precursors on Solution-Processed SnO2 as Electron Transport Layers for CsPbBr3 Perovskite Solar Cells

In this paper, three kinds of SnO2 precursors were comparatively investigated for low temperature solution-processed SnO2 films as electron transport layers (ETL) of CsPbBr3 perovskite solar cells (PSCs). It was found that the precursor state and solvent type played an important role on the crystallinity and film-forming performance of SnO2. All-inorganic hole-transport-layer-free planar CsPbBr3 PSCs with an architecture of FTO/SnO2/CsPbBr3/carbon were fabricated. The best-performing device with SnO2 as ETL by reflux condensation sol spin-coating technique delivered a champion power conversion efficiency (PCE) as high as 6.27%, with a short-circuit current density of 7.36[Formula: see text]mA[Formula: see text]cm[Formula: see text], an open-circuit voltage of 1.29[Formula: see text]V, and a fill factor of 65.9%. It was comparable to the highest PCE record 6.7% of the device with the same structure based on TiO2-ETL so far. Moreover, the CsPbBr3 devices without encapsulation exhibited good stability after being stored under ambient conditions with a relative humidity of [Formula: see text]% at room temperature over 1000[Formula: see text]h and 60[Formula: see text]C for 720[Formula: see text]h, respectively. The results promise the commercial potential of CsPbBr3 PSCs using reflux condensation low-temperature solution-processed SnO2 as ETLs for flexible polymer photovoltaic applications.

Efficient PbSe Colloidal Quantum Dot Solar Cells Using SnO2 as a Buffer Layer.

PbSe colloidal quantum dots (CQDs) are widely used in solar cells because of their tunable band gap, solution processability, and efficient multiple exciton generation effect. The most efficient PbSe CQD solar cells use high-temperature-processed ZnO as the electron transport layer (ETL), limiting their applications in flexible photovoltaics. Currently, low-temperature solution-processed SnO2 has been demonstrated as an efficient ETL for high-efficient PbS CQD and perovskite solar cells because of less parasitic light absorption and higher electron mobility. Herein, we introduce low-temperature solution-processed SnO2 as ETL for PbSe CQD solar cells, and fabricate the PbSe CQD absorber layer with a one-step spin-coating method. The champion device with the structure of FTO (SnO2:F)/SnO2/PbSe-PbI2/PbS-EDT (1,2-ethanedithiol)/Au achieves a high open-circuit voltage of 577.1 mV, a short-circuit current density of 24.87 mA cm-2, a fill factor of 67%, and an impressive power conversion efficiency of 9.67%. Our results pave the way for the development of low-temperature flexible PbSe CQD solar cells.

Red‐Carbon‐Quantum‐Dot‐Doped SnO2 Composite with Enhanced Electron Mobility for Efficient and Stable Perovskite Solar Cells

An efficient electron transport layer (ETL) plays a key role in promoting carrier separation and electron extraction in planar perovskite solar cells (PSCs). An effective composite ETL is fabricated using carboxylic-acid- and hydroxyl-rich red-carbon quantum dots (RCQs) to dope low-temperature solution-processed SnO2 , which dramatically increases its electron mobility by ≈20 times from 9.32 × 10-4 to 1.73 × 10-2 cm2 V-1 s-1 . The mobility achieved is one of the highest reported electron mobilities for modified SnO2 . Fabricated planar PSCs based on this novel SnO2 ETL demonstrate an outstanding improvement in efficiency from 19.15% for PSCs without RCQs up to 22.77% and have enhanced long-term stability against humidity, preserving over 95% of the initial efficiency after 1000 h under 40-60% humidity at 25 °C. These significant achievements are solely attributed to the excellent electron mobility of the novel ETL, which is also proven to help the passivation of traps/defects at the ETL/perovskite interface and to promote the formation of highly crystallized perovskite, with an enhanced phase purity and uniformity over a large area. These results demonstrate that inexpensive RCQs are simple but excellent additives for producing efficient ETLs in stable high-performance PSCs as well as other perovskite-based optoelectronics.

A facile strategy for enhanced performance of inverted organic solar cells based on low-temperature solution-processed SnO2 electron transport layer

High-efficiency organic solar cells (OSCs) based on low-temperature (LT) processed SnO2 electron transport layer (ETL) are promising for their commercial use. However, high density of traps and large contact barrier for carriers at the interface between LT SnO2 and the active layer has been reported. To solve the problem, various interface modifying layer materials, such as PFN, has been introduced. Currently, the fabrication process of such interface modifying layer materials is complex and expensive. Herein, a facile strategy involved a polar solvent ethanolamine (EA) is introduced to modify LT SnO2 surface. By soaking the SnO2 film into EA solution in 2-Methoxyethanol (2-ME), EA can easily anchor into SnO2 film surface and forms a continuous monomolecular layer via dehydration reaction. The whole process is green and highly compatible with a roll-to-roll process. Further study suggests that the deep trap centers on SnO2 surface are substantially reduced and the built-in potential in OSCs is reinforced. Finally, OSCs based on EA-modified SnO2 demonstrated an enhanced power conversion efficiency from 10.71% to 12.45% which was comparable to those based on ZnO (12.26%) under the same experiment parameters. Our work boosts the development of the inverted OSCs with easy fabrication and compatibility with roll-to-roll process.

Graphene-Modified Tin Dioxide for Efficient Planar Perovskite Solar Cells with Enhanced Electron Extraction and Reduced Hysteresis.

Tin dioxide (SnO2) as an efficient electron transport layer (ETL) has been demonstrated for emerging high-performance organic-inorganic hybrid perovskite solar cells (PSCs). However, the low-temperature solution-processed SnO2 usually results in high trap-state density and current-voltage hysteresis. Here, we reported an effective strategy to solve this problem by incorporating graphene ink into the low-temperature processed SnO2 for planar structure PSCs. The electron extraction efficiency has been significantly improved with graphene-doped SnO2 ETL coupled with attenuated charge recombination at the ETL/perovskite interface. The power conversion efficiency (PCE) of PSCs based on the graphene-SnO2 ETL reached over 18% with negligible hysteresis. Incorporation of graphene into the ETL layer also enhanced the device stability retaining 90% of the initial PCE value after storing in ambient condition with a relative humidity of 40 ± 5% for 300 h. Our results provide an important insight into further efficiency boost in SnO2-based low-temperature processed PSCs.

Low-temperature bromide modification of SnO2 for highly efficient perovskite solar cells

The electron transport layer (ETL) plays a crucial role in the rapidly developed perovskite solar cells (PSCs). SnO2 has become one of the most promising alternatives to the TiO2 ETL due to its superior characteristics, such as the wider bandgap and hysteresis-free. However, at this stage, a lot of preparation methods of SnO2 ETL exist in high temperature and long time, those undoubtedly increase the cost and time of preparation. Herein, we report a low-temperature solution-processed SnO2 ETL without high annealing temperature, and a special bromine salt is used to modify SnO2, which leads to a higher transmittance and improved carrier transport ability. Due to the excellent optical and electrical properties, the photoelectric conversion efficiency of the prepared PSC reaches up to 18.8%. Moreover, it can be fabricated using facile solution processing at low temperature, making it particularly attractive for flexible development and low-cost commercialization.

Enhanced Crystallinity of Low-Temperature Solution-Processed SnO2 for Highly Reproducible Planar Perovskite Solar Cells.

Low-temperature solution-processed SnO2 as a promising electron-transport material for planar perovskite solar cells (PSCs) has attracted particular attention because of its outstanding properties such as high optical transparency or high electron mobility. However, low-temperature sol-gel processes used in the synthesis are inevitably affected by the humidity of the atmosphere, which results in a wide distribution in the performance of the prepared PSCs owing to the inability to control crystallinity and defects. Herein, a highly crystalline SnO2 film is synthesized using a simple water bath post-treatment, which can remove the surface residuals of SnCl4 on the SnO2 films, which is beneficial for the interface charge transport from the perovskite to the SnO2 electron-transport layer. An improved performance of the PSCs can be easily obtained applying this treatment, giving rise to a high power conversion efficiency (PCE) of 19.17 %, much higher than that of the pristine SnO2 -based device (17.59 %). Most importantly, the reproducibility of the devices has been greatly improved, independent of the environmental humidity. Therefore, the enhanced crystallinity of SnO2 has shown promise for future commercial PSC applications: 5 cm×5 cm PSC modules have achieved a PCE of 16.16 %.

Low-Temperature Solution-Processed Mg:SnO2 Nanoparticles as an Effective Cathode Interfacial Layer for Inverted Polymer Solar Cell

An efficient inverted polymer solar cell (PSC)-based on bulk heterojunction composites of poly(3-hexylthiophene) (P3HT) and phenyl C61-butryricacid methyl ester (PCBM) has been demonstrated by incorporating facile low-temperature solution-processed Mg-doped SnO2 (Mg:SnO2) nanoparticles as the cathode interfacial layer. Compared to the pure SnO2, the PSCs based on Mg:SnO2 interfacial layer exhibits excellent properties with a power conversion efficiency (PCE) of up to 4.08%, increased from 2.77%, corresponding to a significant 47.29% PCE enhancement. The improved photovoltaic performance is ascribed to the increased electron mobility, elevated electrical conductivity and optimized surface morphology, which makes it an excellent growth platform for a flat and high quality photoactive layer. Furthermore, we show the Mg:SnO2 interfacial layers to dramatically improve the electron extraction and effectively suppress the photogenerated carrier recombination. The low-temperature solution-processed SnO2 with Mg d...

Low-Temperature Solution-Processed SnO2 Nanoparticles as a Cathode Buffer Layer for Inverted Organic Solar Cells.

SnO2 recently has attracted particular attention as a powerful buffer layer for organic optoelectronic devices due to its outstanding properties such as high electron mobility, suitable band alignment, and high optical transparency. Here, we report on facile low-temperature solution-processed SnO2 nanoparticles (NPs) in applications for a cathode buffer layer (CBL) of inverted organic solar cells (iOSCs). The conduction band energy of SnO2 NPs estimated by ultraviolet photoelectron spectroscopy was 4.01 eV, a salient feature that is necessary for an appropriate CBL. Using SnO2 NPs as CBL derived from a 0.1 M precursor concentration, P3HT:PC60BM-based iOSCs showed the best power conversion efficiency (PCE) of 2.9%. The iOSC devices using SnO2 NPs as CBL revealed excellent long-term device stabilities, and the PCE was retained at ∼95% of its initial value after 10 weeks in ambient air. These solution-processed SnO2 NPs are considered to be suitable for the low-cost, high throughput roll-to-roll process on a flexible substrate for optoelectronic devices.

Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

Planar structures for halide perovskite solar cells have recently garnered attention, due to their simple and low-temperature device fabrication processing. Unfortunately, planar structures typically show I–V hysteresis and lower stable device efficiency compared with mesoporous structures, especially for TiO2-based n-i-p devices. SnO2, which has a deeper conduction band and higher electron mobility compared with traditional TiO2, could enhance charge transfer from perovskite to electron transport layers, and reduce charge accumulation at the interface. Here we report low-temperature solution-processed SnO2 nanoparticles as an efficient electron transport layer for perovskite solar cells. Our SnO2-based devices are almost free of hysteresis, which we propose is due to the enhancement of electron extraction. By introducing a PbI2 passivation phase in the perovskite layer, we obtain a 19.9 ± 0.6% certified efficiency. The devices can be easily processed under low temperature (150 ∘C), offering an efficient method for the large-scale production of perovskite solar cells. Planar structured perovskite solar cells often show hysteresis and lower efficiency than mesoporous ones. Jiang et al. show that using a SnO2 electron transport layer improves the performance of planar devices, reporting a certified efficiency of 19.9%, and enables a lower processing temperature.

Efficient planar Sb2S3 solar cells using a low-temperature solution-processed tin oxide electron conductor.

Efficient planar antimony sulfide (Sb2S3) heterojunction solar cells have been made using chemical bath deposited (CBD) Sb2S3 as the absorber, low-temperature solution-processed tin oxide (SnO2) as the electron conductor and poly (3-hexylthiophene) (P3HT) as the hole conductor. A solar conversion efficiency of 2.8% was obtained at 1 sun illumination using a planar device consisting of F-doped SnO2 substrate/SnO2/CBD-Sb2S3/P3HT/Au, whereas the solar cells based on a titanium dioxide (TiO2) electron conductor exhibited a power conversion efficiency of 1.9%. Compared with conventional Sb2S3 sensitized solar cells, the high-temperature processed mesoscopic TiO2 scaffold is no longer needed. More importantly, a low-temperature solution-processed SnO2 layer was introduced for electron transportation to substitute the high-temperature sintered dense blocking TiO2 layer. Our planar solar cells not only have simple geometry with fewer steps to fabricate but also show enhanced performance. The higher efficiency of planar Sb2S3 solar cell devices based on a SnO2 electron conductor is attributed to their high transparency, uniform surface, efficient electron transport properties of SnO2, suitable energy band alignment, and reduced recombination at the interface of SnO2/Sb2S3.